Develop Bugs

[APP][Update to any Firmware region via Kies2.0][SpoofFw][Kies2.0]

A new approach!
Spoof the firmware version on the device, to trick Kies2.0.
But as you might understand, messing with system files is always dangerous and the possibility for a brick is always present. Hopefully this will not occur I'm doing my best to avoid that.
You should not use this app if you cannot get into Recovery and/or Download mode! (3 button combo) As always when you modifies system files!
Remember to disable any lagfix before updating!
For everyones safety I would recommend doing a manual backup of /system/build.prop and the complete /efs folder including nv_data.bin
The app does this automatically to the internal SDCARD, but just to be on the safe side I would recommend a manual backup to the computer aswell.
There is three steps where a reboot is required after step 2. The app will tell you what to do.
Step1.
Backup everything. If this fails, step2 is not available.
Step2.
Set the new ProductCode and PDA. Reboot!
Step3.
Set CSC and Phone. Do NOT reboot. Connect to Kies2.0 and update!
This setting is not permanent and will go back to previous setting after reboot.
Remember to disable any lagfix before updating!
Done!
-------------------------------------------------------------
How to Restore
Press restore in the menu. Reboot required.
If something fails, please send me your logcat.
So here it is: SpoofFw - requires ROOT and BusyBox
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Online Market link
If you get problems to connect to Kies after you used this program, try remove the registry key "HKEY_CURRENT_USER\Software\Samsung\Kies\DeviceDB"
Please let me now if it works out for you.
If you like my work, please consider a small donation.

Thanks a lot for your patch

Hi,
I'm new to the forum and am very interested in your work, at the moment the file to "fool " Kies 2.0 has not worked for me. I have the version 2.2 of Android 9000XWJPB/I9000FOPJP3/I9000XXJPP/I9000XWJPB and product code FOP. Sorry for my english, i'm from Spain.

what is new in this ??

It does'nt entirely work. Tried and it shows me update available.
But when it supposed to start downloading new rom, it say that latest software is already installed in my phone.Then Kies resets and start over offering update again.
So, I guess it detects the real rom in the phone.
Nice patch, though. Maybe you can see what is the problem.
Thanks

Same here - I just posted in the "original" theme about kies registry patcher.
Kies finds update, and when i start upgrading, the phone disconnects, and then after 1s reconects back. I cannot upgrade.

oh crap. didnt try to actually download it. thought it would work. I'll have a look at it. sorry guys.

No panic
Obviously some can upgrade, some cannot. We are the first with this problem.
I have jpx. Could this cause problems?

Those of you who have tried the patch, can you please post your info from the registry and tell me if it worked or not. Include both product code, hidswver, softwarerevision and modelname.

For me, in the registry is still JPY everywhere, after apply patch.
PRODUCT code : GT-I9000HKDXEU
HIDSWVER: I9000XXJPY/I9000OXAJPY/I9000XXJPY/I9000XXJPY
Model Name:GT-I9000
Software Revision: I9000XXJPY/I9000OXAJPY/I9000XXJPY/I9000XXJPY

HTH....
Running Kies 2.0.0.11014_49
HIDSWVER I9000XXJPO/I9000OXAJPO/I9000XXJPP/I9000XXJPO
Product Code GT-I9000HKDTMU
Model Name GT-I9000
Doesn't work unfortunately - it offers me an upgrade, appears to download the file then gives the Disconnected error.
I've also tried manually editing the registry as per kies 1.5 but no more luck.
I've tried on 2 PCs too.

HIDSWVER: I9000BUJP7/I9000GVD2JP5/I9000BUJP5/I9000BUJP7 (SofwareRev is same)
FW: I9000BUJP7/I9000GVD2JP5(CSC)/I9000BUJP5(modem)
PCode: GT-I9000HKDVD2 (VD2)
Kies: v2.0.0.11014_49
OS: Win7 Ultimate 64bit
I checked my registry but to no avail. Also tried deleting DeviceDB key to force kies into reconstructing it. It doesn't offer the fw upgrade option at all.
At least it's good to know someone is trying to develop a way to spoof kies 2.0. Did the patch work with any previous versions of kies 2.0?

I just got some another idea: could we try to hack ProductCode on device instead of on Kies side?
AFAIU ProductCode == CSC. I've googled we can change CSC in following ways:
1) *#272*HHMM# on Android 2.1 and older
2) *#272*IMEI# on Android 2.2 and newer
3) Opening preconfing with ADB
4) Editing /efs/nv_data.bin
Would it make Kies detecting different ProductCode?
There is still one more thing we have to consider: what if Kies detects our changed ProductCode but also firmware versions that were never released for given ProductCode?

Zajec5 said:
I just got some another idea: could we try to hack ProductCode on device instead of on Kies side?
AFAIU ProductCode == CSC. I've googled we can change CSC in following ways:
1) *#272*HHMM# on Android 2.1 and older
2) *#272*IMEI# on Android 2.2 and newer
3) Opening preconfing with ADB
4) Editing /efs/nv_data.bin
Would it make Kies detecting different ProductCode?
There is still one more thing we have to consider: what if Kies detects our changed ProductCode but also firmware versions that were never released for given ProductCode?
Click to expand...
Click to collapse
I have thought about it too. But we still need to change the PDA and PHONE aswell. But I have not yet located where they are stored. My guess is it's hard coded somewhere. Still the drivers need to take it from somewhere, the question is where.

LuffarJoh said:
I have thought about it too. But we still need to change the PDA and PHONE aswell. But I have not yet located where they are stored. My guess is it's hard coded somewhere. Still the drivers need to take it from somewhere, the question is where.
Click to expand...
Click to collapse
There is something like
getBasebandVersion, but I can't track RILRequest, how is is reading RIL_REQUEST_BASEBAND_VERSION... That could show us some file with baseband version maybe.

I have had some progress.
I have managed to change all necessary codes in the phone to be able to spoof Kies. This time I passed the step that the patch didnt!
Unfortunately it's not that simple, it requires root and changes system properties. But it's all reversible. I think I'll try to make an app of it during next week. First is a final exam on Monday.
watch this space.

well, it's much more fun to develop android application then study for an exam
I have successfully switched from XEN to XEE and to DBT.
I'm almost done, just some more bug testing. I'll probably release it tonight

Good news, wait for your release tonight.

luffarjoh said:
well, it's much more fun to develop android application then study for an exam
i have successfully switched from xen to xee and to dbt.
I'm almost done, just some more bug testing. I'll probably release it tonight
Click to expand...
Click to collapse
great news!!!

I have to push the release until tomorrow, I still have some fine tuning to do! Overall is works very well

[Release]XapSpyAnalysis - a graphical tool for runtime analysis

Hi XDA developers!
Today I present you my first open source software called XapSpyAnalysis. You can download a compiled version and the sourcecode at xapspyanalysis.codeplex.com. It is an extension to Behrang Fouladis excellent XapSpy tool.
First, you need to use XapSpy. You need to start XapSpy and select a XAP package you want to analyse. It will be unpacked, stripped from its licence information, patched, signed and repacked. The next step is to launch the Emulator. This is automatically done from XapSpy. After it is booted, the application will get deployed to the emulator. After this is completed, XapSpy will inform you, that you can run the Monitor from inside XapSpy. This is where XDEMonitor kicks in. It will log all method calls and its variables it can get from the emulator log window. When you are finished, you can stop the recording and save the file to your harddisk.
This file can be loaded into XapSpyAnalysis. It will parse the file and display its raw content in the first tab. You can now switch between different views. You can display a table that contains all method calls with their variables, the DLL file from where the method call originates and its time. The next tab lists all method names and their number of calls. The next tab lists statistic values like how many method calls were registered and how many of them were unique method calls.
The final tab displays a graphical analyis of the method calls. The x axis displays the point of time, when the method was called. The y axis displays the number of method that was called. This is an unfortunate restriction from the used graphic framework. You can find a legend on the right side of the diagram. It maps the numbers to method names. But you can also point your mouse cursor on any of the data points in the diagram. A tooltip will be availabe that shows you the corresponding method name.
Now some screenshots:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This screenshot shows an application, that crashes three times. You can see this from the data points starting with method 0 (InitializeComponent) and method 22 (Application_UnhandledException).
This screenshot shows an application that is properly executed and closed. It starts with method 0 (InitializeComponent) and calls a camera chooser (which is why method 0 is again called). This is a good example to see how Windows Phone 7 Multitasking and tombstoning works, because you can see when the methods Application_Deactivated and Application_Activated are used.
I hope this tool might be useful for some of you, especially when you want to understand how an application works. The apps can be even obfuscated. You will than only see method names like A, B, C etc. You can even check what other applications do, when they crash and that without having the source code.
If you have any ideas or find some bugs (and there will be bugs ) you can write me here on XDA or at Codeplex bugtracker. Already existing bugs and limitations can be found in the codeplex documentation.
Cheers,
Markus

rudelm said:
Hi XDA developers!
Today I present you my first open source software called XapSpyAnalysis. You can download a compiled version and the sourcecode at xapspyanalysis.codeplex.com. It is an extension to Behrang Fouladis excellent XapSpy tool.
First, you need to use XapSpy. You need to start XapSpy and select a XAP package you want to analyse. It will be unpacked, stripped from its licence information, patched, signed and repacked. The next step is to launch the Emulator. This is automatically done from XapSpy. After it is booted, the application will get deployed to the emulator. After this is completed, XapSpy will inform you, that you can run the Monitor from inside XapSpy. This is where XDEMonitor kicks in. It will log all method calls and its variables it can get from the emulator log window. When you are finished, you can stop the recording and save the file to your harddisk.
This file can be loaded into XapSpyAnalysis. It will parse the file and display its raw content in the first tab. You can now switch between different views. You can display a table that contains all method calls with their variables, the DLL file from where the method call originates and its time. The next tab lists all method names and their number of calls. The next tab lists statistic values like how many method calls were registered and how many of them were unique method calls.
The final tab displays a graphical analyis of the method calls. The x axis displays the point of time, when the method was called. The y axis displays the number of method that was called. This is an unfortunate restriction from the used graphic framework. You can find a legend on the right side of the diagram. It maps the numbers to method names. But you can also point your mouse cursor on any of the data points in the diagram. A tooltip will be availabe that shows you the corresponding method name.
Now some screenshots:
This screenshot shows an application, that crashes three times. You can see this from the data points starting with method 0 (InitializeComponent) and method 22 (Application_UnhandledException).
This screenshot shows an application that is properly executed and closed. It starts with method 0 (InitializeComponent) and calls a camera chooser (which is why method 0 is again called). This is a good example to see how Windows Phone 7 Multitasking and tombstoning works, because you can see when the methods Application_Deactivated and Application_Activated are used.
I hope this tool might be useful for some of you, especially when you want to understand how an application works. The apps can be even obfuscated. You will than only see method names like A, B, C etc. You can even check what other applications do, when they crash and that without having the source code.
If you have any ideas or find some bugs (and there will be bugs ) you can write me here on XDA or at Codeplex bugtracker. Already existing bugs and limitations can be found in the codeplex documentation.
Cheers,
Markus
Click to expand...
Click to collapse
Fascinating! I'll have to check this out against my xaps

I tried to follow the instructions but they were a bit confusing. The program crashes every time I select a XAP

@snickler: I am looking forward to your feedback
@MJCS: Ok, where do you get stuck? I still need to write a better documentation I guess
You downloaded Behrangs XapSpy and replaced the XDEmonitor files with the files from my version? Do you use the WP7 or WP7.5 SDK? There is an important difference regarding the naming of the emulator. In WP7 it is called Windows Phone 7 Emulator, while in WP7.5 it is just Windows Phone Emulator.

I am using 7.5
**
Ahhh I just noticed the 7.1 binaries. Now it works. Thank you!!!

Glad to hear I am really looking forward to your feedback!

[GUIDE]Karbonn A5,A7,Walton Primo IMEI writting & No Sim Problem Fixing

All right everyone here I will give u the method of writing IMEI & No Sim Detection problem of Karbonn A5/W619/Walton Primo & Karbonn A7/S01..
Many of the User of A5 are having problem with the IMEI & Mobile network lost and no sim is detecting while upgrading or downgrading Baseband.
As I have been searching for solution about a month and there is no specific solution regarding this problem..Through some ideas from different sites & developer and experimenting with my own device I have managed to write back both IMEI & enabled mobile network.
Note: For A7 user Please download AP of your device not this one.
Software & Other Requirement:
1.Stock AP of Karbonn A5/W619/Walton Primo (Original Stock GB Rom).
Link : http://jabadbd24.blogspot.com/2013/03/walton-primo-karbon-a5-downgrade-to-gb.html
2.Baseband- V3025 & V3070 both.
3.Fastboot 1.0.2.4 (for downloading AP+BP to device).
4.Drivers.
5.QPST Modem Tool V1.1 (for writing IMEI).
Link : http://www.mediafire.com/download/c9nv2zc1a233s13/Qualcomm_Modem_Tools%20V1.1.rar
6.QPST 2.7 (for restoring network).
Link : http://www.mediafire.com/download/kna2s9x3z06gcuu/QPST_2.7_378.zip
*********************************** FB ID= facebook.com/dj.rifat*****************************************************
Procedure:
A. (BP+AP) Download:
1.If u have upgraded your device to ICS then u have to Downgrade to GingerBread. First goto recovery mode(CWM/TWRP).Goto mount and select all and wipe data,system,boot,cache,android secure,SD-ext.Then Power off the device.
2.Then Update BP.First with V3025 (591347_8376_WCDMA_V3025) & then with V3070 (591347_8376_WCDMA_V3070).
[note: before updating V3070 baseband,Copy and replace 'appsboot.mbn' & 'appsboothd.mbn' this two files from the AP folder to V3070 folder in ur PC.]
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3.Then update Gingerbread AP in Fastboot mode (green screen on device).
4.Turn on mobile while it is connected with the PC.PC will detect new hardware.One from them u installed before while BP Download..
5.Goto Device Manager of PC.U will find three new hardware.Install driver for them.As Shown below:
B. Write IMEI
1)Unzip “Qualcomm_Modem_Tools_V1.1.rar”, open Qualcomm_Modem_Tools.exe, (Turn on ADB Debugging from Application>Development>ADB Debugging from ur mobile)
interface as blew:
(2) Select port. Port should be same as modem port.
(3) Write IMEI. Input new IMEI, click “write”.
(4) Complete writing IMEI.
(5) Then click read, confirm the new IMEI is successful written
C.Fixing NO sim problem and Network.
Now Install ''QPST 2.7.398.exe'' on PC.
(1) Open “QPST Software Download”(Start>Programs>QPST Software Download) and click Restore, interface as below:
(2) Power on handset, connect usb cable and select port by pressing browse as shown below.
(3) Now press the 2nd browse button and navigate to the folder of V3070 Baseband folder ( '591347_8376_WCDMA_V3070' this folder) and select ''591347_8376_WCDMA_V3070.qcn'' file. Now press START ,if you have done everything correctly it will go good.
(4)Restart your mobile.Now goto to Backup Tab and type a name in QCN file column according to ur choice for better understanding which qcn file is the working backup and select location where you wanna save it and press start.This qcn file is important because if u lost ur IMEI sometimes during upgrade or downgrade restoring this file will
recover ur IMEI & network.
This way I have solved my problem.I apologize As I am not a expert in this field if any mistake done by me.
If you don't understand any steps or having problem please let me know will try my best to help you.
You can also find me in facebook/dj.rifat if need help.
Thanks.
Hit like If I have helped you.

Gr8 work bro.. i appritiate your work..!

Rifat.ahmed08 said:
All right everyone here I will give u the method of writing IMEI & No Sim Detection problem of Karbonn A5/W619/Walton Primo & Karbonn A7/S01..
Many of the User of A5 are having problem with the IMEI & Mobile network lost and no sim is detecting while upgrading or downgrading Baseband.
As I have been searching for solution about a month and there is no specific solution regarding this problem..Through some ideas from different sites & developer and experimenting with my own device I have managed to write back both IMEI & enabled mobile network.
Note: For A7 user Please download AP of your device not this one.
Software & Other Requirement:
1.Stock AP of Karbonn A5/W619/Walton Primo (Original Stock GB Rom).
Link : http://jabadbd24.blogspot.com/2013/03/walton-primo-karbon-a5-downgrade-to-gb.html
2.Baseband- V3025 & V3070 both.
3.Fastboot 1.0.2.4 (for downloading AP+BP to device).
4.Drivers.
5.QPST Modem Tool V1.1 (for writing IMEI).
Link : http://www.mediafire.com/download/c9nv2zc1a233s13/Qualcomm_Modem_Tools%20V1.1.rar
6.QPST 2.7 (for restoring network).
Link : http://www.mediafire.com/download/kna2s9x3z06gcuu/QPST_2.7_378.zip
*********************************** FB ID= facebook.com/dj.rifat*****************************************************
Procedure:
A. (BP+AP) Download:
1.If u have upgraded your device to ICS then u have to Downgrade to GingerBread. First goto recovery mode(CWM/TWRP).Goto mount and select all and wipe data,system,boot,cache,android secure,SD-ext.Then Power off the device.
2.Then Update BP.First with V3025 (591347_8376_WCDMA_V3025) & then with V3070 (591347_8376_WCDMA_V3070).
[note: before updating V3070 baseband,Copy and replace 'appsboot.mbn' & 'appsboothd.mbn' this two files from the AP folder to V3070 folder in ur PC.]
3.Then update Gingerbread AP in Fastboot mode (green screen on device).
4.Turn on mobile while it is connected with the PC.PC will detect new hardware.One from them u installed before while BP Download..
5.Goto Device Manager of PC.U will find three new hardware.Install driver for them.As Shown below:
B. Write IMEI
1)Unzip “Qualcomm_Modem_Tools_V1.1.rar”, open Qualcomm_Modem_Tools.exe, (Turn on ADB Debugging from Application>Development>ADB Debugging from ur mobile)
interface as blew:
(2) Select port. Port should be same as modem port.
(3) Write IMEI. Input new IMEI, click “write”.
(4) Complete writing IMEI.
(5) Then click read, confirm the new IMEI is successful written
C.Fixing NO sim problem and Network.
Now Install ''QPST 2.7.398.exe'' on PC.
(1) Open “QPST Software Download”(Start>Programs>QPST Software Download) and click Restore, interface as below:
(2) Power on handset, connect usb cable and select port by pressing browse as shown below.
(3) Now press the 2nd browse button and navigate to the folder of V3070 Baseband folder ( '591347_8376_WCDMA_V3070' this folder) and select ''591347_8376_WCDMA_V3070.qcn'' file. Now press START ,if you have done everything correctly it will go good.
(4)Restart your mobile.Now goto to Backup Tab and type a name in QCN file column according to ur choice for better understanding which qcn file is the working backup and select location where you wanna save it and press start.This qcn file is important because if u lost ur IMEI sometimes during upgrade or downgrade restoring this file will
recover ur IMEI & network.
This way I have solved my problem.I apologize As I am not a expert in this field if any mistake done by me.
If you don't understand any steps or having problem please let me know will try my best to help you.
You can also find me in facebook/dj.rifat if need help.
Thanks.
Hit like If I have helped you.
Click to expand...
Click to collapse
Thank you very much. can u please tell about karbonn a7 plus stock AP where to find. i m having this mobile and facing the same problem.

Thank you so much!!!
I made an account just to say thank for this GUIDE. I was looking and waiting for a year for this GUIDE. THANK YOU SO MUCH!!!:good:

#Respect
Just register an account to post reply. Great work bro, help me pick my phone up from hell :laugh::good::good::good:

vktisnow said:
Thank you very much. can u please tell about karbonn a7 plus stock AP where to find. i m having this mobile and facing the same problem.
Click to expand...
Click to collapse
got my problem solved. thanks a lot for this awesome guide

Anybody can give proper link for the Files.. Most of them are DEAD !!!

i found Port number (COM6).. after this i am unable to write IMEI number(getting error Write IMEI fail). i have entered my old imei number.
when i dial *#06# in my mobile displaying as below:
IMEI1:
IMEI2:
both blanks...(So i entered old IMEI numbers).
And from where can i get new IMEI numbers?
can you please help me on this.

Does this work for SM-A520FDS?

Help unlock huawei HWD14

no way to putt NCK , no information on internet , Putty erro, DC unlocker not support .if found NCK how do i use that ? firmware update?? but where? this is real challenging for me
tks
ATI
Manufacturer: Huawei Technologies Co., Ltd.
Model: HWD14
Revision: 11.232.03.10.824
IMEI: 3528980453****
+GCAP: +CGSM
OK
AT^NVRDEX=50503,0,128
ERROR

Anandasri2 said:
no way to putt NCK , no information on internet , Putty erro, DC unlocker not support .if found NCK how do i use that ? firmware update?? but where? this is real challenging for me
tks
ATI
Manufacturer: Huawei Technologies Co., Ltd.
Model: HWD14
Revision: 11.232.03.10.824
IMEI: 3528980453****
+GCAP: +CGSM
OK
AT^NVRDEX=50503,0,128
ERROR
Click to expand...
Click to collapse
Found modem : M9625E-1
Model : Huawei HWD15
IMEI : 352898045xxxxxx
Serial NR. : N7SDW1431700xxxx
Firmware : 11.232.03.10.824
Dashboard version : 22.001.26.06.824
SIM Lock status : Locked (Card lock)
Wrong codes entered : 0 (unlock attempts left : 10)
sorry, this modem not supported !

Anandasri2 said:
Found modem : M9625E-1
DC unlocker
Model : Huawei HWD15
IMEI : 352898045xxxxxx
Serial NR. : N7SDW1431700xxxx
Firmware : 11.232.03.10.824
Dashboard version : 22.001.26.06.824
SIM Lock status : Locked (Card lock)
Wrong codes entered : 0 (unlock attempts left : 10)
sorry, this modem not supported !
Click to expand...
Click to collapse
CardLock_UnLock-e58xx/HUAWEI MODEM Code Writer not working ether for NCK enter may be Firmware block ..!

Anandasri2 said:
CardLock_UnLock-e58xx/HUAWEI MODEM Code Writer not working ether for NCK enter may be Firmware block ..!
Click to expand...
Click to collapse
only firmware online is "easy-firmware" looks scam to me cuss it's paid and suspicious .
HWD14_11.232.03.30.824_22.001.26.06.824
HWD14TCPU-V100R001B232D03SP30C824_Firmware_05012FPY.zip
Date: 26-09-2018  | Size: 270.65 MB
found something working but got error
"CardLock_UnLock-e58xx " code writer detect this device but when enter NCK its got error, may be due to firmware block
For NCK used old V1 algo cuss imei# start we 35XXXXXXXXXXX
but non of attempts count according to DC unlocker still remain 10 chances
if not found any solution soon i will try to update it by Web UI built in using auto update, but still hesitate to do cuss it may more difficult to unlock
*i tried using puty telnet /Serial commands but no success
++++++++++++++++++++++++++++++++++++++++
1.at^sfm=1
2.at^reset
3.AT^NVWREX=8268,0,12,1,0,0,0,2,0,0,0,A,0,0,0
4.at^sfm=0
5.at^reset
+++++++++++++++++++++++++++++++++++
atc ati
atc at^nvwrex=8268,0,12,1,0,0,0,2,0,0,0,a,0,0,0
+++++++++++++++++++++++++++++++++++=
ATI
ATI
AT^NVRDEX=50503,0,128
++++++++++++++++++++++++++++++++++++
if i found any progress i will update , also if some one can help much appreciate...!:angel:
tks,

Anandasri2 said:
only firmware online is "easy-firmware" looks scam to me cuss it's paid and suspicious .
HWD14_11.232.03.30.824_22.001.26.06.824
HWD14TCPU-V100R001B232D03SP30C824_Firmware_05012FPY.zip
Date: 26-09-2018  | Size: 270.65 MB
found something working but got error
"CardLock_UnLock-e58xx " code writer detect this device but when enter NCK its got error, may be due to firmware block
For NCK used old V1 algo cuss imei# start we 35XXXXXXXXXXX
but non of attempts count according to DC unlocker still remain 10 chances
if not found any solution soon i will try to update it by Web UI built in using auto update, but still hesitate to do cuss it may more difficult to unlock
*i tried using puty telnet /Serial commands but no success
++++++++++++++++++++++++++++++++++++++++
1.at^sfm=1
2.at^reset
3.AT^NVWREX=8268,0,12,1,0,0,0,2,0,0,0,A,0,0,0
4.at^sfm=0
5.at^reset
+++++++++++++++++++++++++++++++++++
atc ati
atc at^nvwrex=8268,0,12,1,0,0,0,2,0,0,0,a,0,0,0
+++++++++++++++++++++++++++++++++++=
ATI
ATI
AT^NVRDEX=50503,0,128
++++++++++++++++++++++++++++++++++++
if i found any progress i will update , also if some one can help much appreciate...!:angel:
tks,
Click to expand...
Click to collapse
working this command
but
ATI
> AT ^ CARDLOCK?
^ CARDLOCK: 1,10,0
when enter
AT ^ CARDLOCK = "Xx NCK CodeXXX" nothings happen so i realize this is firmware block ...
so i have to find modified firmware for do this so if any one have access to easy-firmware. com resource and get "HWD14_11.232.03.30.824_22.001.26.06.824 HWD14TCPU-V100R001B232D03SP30C824_Firmware_05012FPY.zip" pls share with me : so at least give a try ..

Anandasri2 said:
working this command
but
ATI
> AT ^ CARDLOCK?
^ CARDLOCK: 1,10,0
when enter
AT ^ CARDLOCK = "Xx NCK CodeXXX" nothings happen so i realize this is firmware block ...
so i have to find modified firmware for do this so if any one have access to easy-firmware. com resource and get "HWD14_11.232.03.30.824_22.001.26.06.824 HWD14TCPU-V100R001B232D03SP30C824_Firmware_05012FPY.zip" pls share with me : so at least give a try ..
Click to expand...
Click to collapse
+++++++++++++++++++++ DAY 5 ++++++++++++++++++++++++++++
finally found way to download original Firmware , with all revision
HWD14_UPDATE_11.232.03.10.824_22.001.26.06.824.ZIP English/Japanese
HWD14_UPDATE_11.232.03.30.824_22.001.26.06.824.ZIP English/Japanese
bit of research i realize ZIP is a compressed bin file, not a compressed package.. also i know nothing abut these files so i have to dig more to learn how to handle those file may it's impossible but still i don't
know :laugh:
now i have
*firmware file
*Hi links drivers to enable COM port

Anandasri2 said:
+++++++++++++++++++++ DAY 5 ++++++++++++++++++++++++++++
finally found way to download original Firmware , with all revision
HWD14_UPDATE_11.232.03.10.824_22.001.26.06.824.ZIP English/Japanese
HWD14_UPDATE_11.232.03.30.824_22.001.26.06.824.ZIP English/Japanese
bit of research i realize ZIP is a compressed bin file, not a compressed package.. also i know nothing abut these files so i have to dig more to learn how to handle those file may it's impossible but still i don't
know :laugh:
now i have
*firmware file
*Hi links drivers to enable COM port
Click to expand...
Click to collapse
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
working with some tools in linux (binwalk... ect ) but still no luck if some one can mod this firmware pls let me know i will send the link ... cuss it's long way to go learn Reverse Engineering :silly:

Anandasri2 said:
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
working with some tools in linux (binwalk... ect ) but still no luck if some one can mod this firmware pls let me know i will send the link ... cuss it's long way to go learn Reverse Engineering :silly:
Click to expand...
Click to collapse
FM file links
http://update.hicloud.com:8180/TDS/..._UPDATE_11.232.03.10.824_22.001.26.06.824.ZIP
http://update.hicloud.com:8180/TDS/..._UPDATE_11.232.03.30.824_22.001.26.06.824.ZIP

Anandasri2 said:
FM file links
http://update.hicloud.com:8180/TDS/..._UPDATE_11.232.03.10.824_22.001.26.06.824.ZIP
http://update.hicloud.com:8180/TDS/..._UPDATE_11.232.03.30.824_22.001.26.06.824.ZIP
Click to expand...
Click to collapse
doesn't work because the file is corrupted looks like it's faking about corrupt cuss looks suspicious to me ,i think archive is good but they don't need open it easily:laugh: still looking forward
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Anandasri2 said:
doesn't work because the file is corrupted looks like it's faking about corrupt cuss looks suspicious to me ,i think archive is good but they don't need open it easily:laugh: still looking forward
Click to expand...
Click to collapse

Question call recorder

i've seen too many videos on youtube that teach indian users how to enable automatic call recording on their samsung a32 4g , but unfortunately that option is not available on my device.
is it possible that some how i get that feature ?
for example by dumping an indian phone apk file or something ?

amiravandfar said:
i've seen too many videos on youtube that teach indian users how to enable automatic call recording on their samsung a32 4g , but unfortunately that option is not available on my device.
is it possible that some how i get that feature ?
for example by dumping an indian phone apk file or something ?
Click to expand...
Click to collapse
i would really appreciate if a user from india extracts phone dialer apk and uploads it here so we can test.
i've seen the same worked for huawei phones.

To activate the call recording it is not the call apk, it is a code that is added to the build.pro or the csc, I do not remember well in one of the two.

PatricioCarrasco said:
To activate the call recording it is not the call apk, it is a code that is added to the build.pro or the csc, I do not remember well in one of the two.
Click to expand...
Click to collapse
thanks for your insight, i was totally clueless before.
it's csc , which is the country code.

here is my experience id like to share :
1-dial *#1234# with your dialer , and it shows you 3 numbers , screenshot it and save it somewhere diffrent than in your phone.
2-download your indonesian firmware for a32 from sammobile that has the same version ending characters as yours.
3-choose home csc from the package and put it in csc part of odin.
4- connect your pc to your phone with an original cable to a usb2 port (if you are on a pc , use backside ports of case) , disconnect every other usb devices.
5-click start of odin , the whole process should be completed in less than a minute and you will get native call recording without data loss.

Thanks for this guide. Works without data loss.

amiravandfar said:
here is my experience id like to share :
1-dial *#1234# with your dialer , and it shows you 3 numbers , screenshot it and save it somewhere diffrent than in your phone.
2-download your indonesian firmware for a32 from sammobile that has the same version ending characters as yours.
3-choose home csc from the package and put it in csc part of odin.
4- connect your pc to your phone with an original cable to a usb2 port (if you are on a pc , use backside ports of case) , disconnect every other usb devices.
5-click start of odin , the whole process should be completed in less than a minute and you will get native call recording without data loss.
Click to expand...
Click to collapse
HI,
in my case, Galaxy A32 4g, it works great, take less than 30s. If I need to make a factory reset? My old CSC was OXM, is it still in the phone?
Best regards

amiravandfar said:
here is my experience id like to share :
1-dial *#1234# with your dialer , and it shows you 3 numbers , screenshot it and save it somewhere diffrent than in your phone.
2-download your indonesian firmware for a32 from sammobile that has the same version ending characters as yours.
3-choose home csc from the package and put it in csc part of odin.
4- connect your pc to your phone with an original cable to a usb2 port (if you are on a pc , use backside ports of case) , disconnect every other usb devices.
5-click start of odin , the whole process should be completed in less than a minute and you will get native call re
Click to expand...
Click to collapse
amiravandfar said:
here is my experience id like to share :
1-dial *#1234# with your dialer , and it shows you 3 numbers , screenshot it and save it somewhere diffrent than in your phone.
2-download your indonesian firmware for a32 from sammobile that has the same version ending characters as yours.
3-choose home csc from the package and put it in csc part of odin.
4- connect your pc to your phone with an original cable to a usb2 port (if you are on a pc , use backside ports of case) , disconnect every other usb devices.
5-click start of odin , the whole process should be completed in less than a minute and you will get native call recording without data loss.
Click to expand...
Click to collapse
Please I want to find out whether I have to root my phone before I start or I should just go ahead without rooting the phone. I'm grateful for sharing your knowledge here.

[email protected] said:
HI,
in my case, Galaxy A32 4g, it works great, take less than 30s. If I need to make a factory reset? My old CSC was OXM, is it still in the phone?
Best regards
Click to expand...
Click to collapse
Its not stored in the phone , if you reset factory it will be reset with the new csc !

della-dell said:
Please I want to find out whether I have to root my phone before I start or I should just go ahead without rooting the phone. I'm grateful for sharing your knowledge here.
Click to expand...
Click to collapse
No rooting is required.

amiravandfar said:
here is my experience id like to share :
1-dial *#1234# with your dialer , and it shows you 3 numbers , screenshot it and save it somewhere diffrent than in your phone.
2-download your indonesian firmware for a32 from sammobile that has the same version ending characters as yours.
3-choose home csc from the package and put it in csc part of odin.
4- connect your pc to your phone with an original cable to a usb2 port (if you are on a pc , use backside ports of case) , disconnect every other usb devices.
5-click start of odin , the whole process should be completed in less than a minute and you will get native call recording without data loss.
Click to expand...
Click to collapse
Please I have downloaded and installed the Odin3 v3.14. I have downloaded the package and chosen the Home CSC and put it in the CSC section of Odin. I clicked START and nothing happens. Please help me. I have attached some images to help you understand my problem so you can guide me. Thank you.

amiravandfar said:
No rooting is required.
Click to expand...
Click to collapse
amiravandfar said:
here is my experience id like to share :
1-dial *#1234# with your dialer , and it shows you 3 numbers , screenshot it and save it somewhere diffrent than in your phone.
2-download your indonesian firmware for a32 from sammobile that has the same version ending characters as yours.
3-choose home csc from the package and put it in csc part of odin.
4- connect your pc to your phone with an original cable to a usb2 port (if you are on a pc , use backside ports of case) , disconnect every other usb devices.
5-click start of odin , the whole process should be completed in less than a minute and you will get native call recording without data loss.
Click to expand...
Click to collapse
After change csc ,when you make call is caller ID fail to identify number region? I guess it will fail..pls confirm

Please update, I need this as well. When you change the CSC does it do a reset? That is usually required. I'm trying to do it on my brothers phone and would rather not tell him i need to do a hard reset

Sir, I have done procedure step by step as you guided but in notification message shown, (Process completed 0/ successful 0). Nothing change in mobile too. please guide about your Point 4. Either we connect mobile with PC through USB cable without Flashing mode or put mobile in flashing mode first then connect to PC? Please guide step by step, because I am a simple mobile user not software engineer. Thanks in advance.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

[email protected] said:
HI,
in my case, Galaxy A32 4g, it works great, take less than 30s. If I need to make a factory reset? My old CSC was OXM, is it still in the phone?
Best regards
Click to expand...
Click to collapse
Hi, I have performed step by step all procedure but not successful. Screen short attached. Please guide, either attache Mobile with PC in Flashing mode (using Home+Power+vol down key) or simply attach with USB cable and allow to use data?