Ok, I switched up from the Epic, and that thing was almost impossible to brick. Every time I tried to install new ROMS, kernels, whatever, if it failed, I was always able to get it into download mode, Odin the stock ROM, and I was back and working.
I'm not a ROM newb, but this was the first time trying something with the E4GT. For this phone, I was trying to install one of the pre-rooted kernels, and the process failed. I let odin say it failed and unplugged the phone, pulled the battery and tried to get it into download mode again (Vol down + Power) but all I get is the Blue LED, nothing else. Screen and buttons don't light up, no USB recognition (with many various cables.) The most I get is the blue LED.
So, is it totally screwed?
If I can't get something going, I am just going to have the store replace it. (Good rapport with the SM, since it's not working at all, I will likely have her replace it with a new handset today.)
I'd rather not waste a perfectly good phone though if it isn't totally screwed.
Any suggestions?
You probably arent screwed try this and do it step by step
Turn phone off plug your usb into the comp FIRST hold vol down first then power "keep holdin them" galaxy s logo may appear twice before entering dload mode!!
Then you should be in dload mode hit volume up then connect your usb cord to phone
then open odin
also try plugging in your usb cord to epic first with the battery out hold vol down and power then put battery in real fast after that may help into download mode
Side note see if your battery shows charging on front screen when you, plug usb in , im curious to see if you did the same thing i did, oh yes you can hard brick it easily i did two days ago... but i flashed a aTAT GSM rom, over the cdma phone which is a pemabrick instantly, i lost all usb recognition for good!!
---------- Post added at 12:57 AM ---------- Previous post was at 12:54 AM ----------
I forgot to mention try the 3 button combo for dload mode that the gt i9100 uses hold VOL DOWN, @ HOME BUTTON @ POWER all at once its worth a shot after i flashed the gsm tar file i had to use the atat download mode ,method for their galaxy s device
---------- Post added at 12:59 AM ---------- Previous post was at 12:57 AM ----------
Theres no way you dont have dload mode,unless you flashed a kernel from a gsm rom, are you certain it was one of the kernels for the epic touch 4g, your probably just having a hard time gettin the button config right for dload mode
nope, doesn't work. I tried everything you said above, and it does nothing more than light the blue LED.
I was trying to flash the deodexed-rooted-busybox-EG30.tar, but it didn't get to that point in Odin.
I think this is one of the first non-gsm kernel true bricks...
In a flashing video, one of the ACS guys said if a flash didn't take and you are having issues, pull the battery and let the sit an hour or two with out power. Maybe push power button to try to drain the phone completely. Then try reflashing. Sounds a little wishful to me but maybe he knows something I don't.
Google Samsung epic 4g jig and try to find the documentation for making one. It's only a micro usb plug and a 301K resistor jumping pins. Maybe that will get you into download mode.
reply
take it to a service repair center, dont mention flashing tars, just say u did a kies update on windows 7 64 bit and it crashed they are wll aware that kies wasnt optimized for windows 7 at some point and theyve seen alot of these crashes, just act like you have no idea and no nothing about android, theyll take it right into the back try to flash the tar then, if they cant get it into odin, theyll simply throw a new motherboard in.. tel em its your only phone , they wont let u leave without it working..
thats what theyre paid to do they have parts, they wont charge you and if you dont have insurance theyll add it on the spot..
took me 25 min and i walked out with a working epic.
Then when u get it id leave it be.. or have someone else do the kernal flashing.
---------- Post added at 01:51 AM ---------- Previous post was at 01:48 AM ----------
Theyre have been more bricking with this perticular phone than i have ever seen with samsung before... Not sure why, but mine was by mistake, i had taken a bad tar file for a gt i9100 atat phone that was renamed eg30.tar so i got screwed by an asshole!!
---------- Post added at 01:54 AM ---------- Previous post was at 01:51 AM ----------
That makes sense, kinda like when you replace a part on a vehicle that was throwing a bad code it wont fix the issue until you pull the batt cable and turn on your lights to fully drain your computer brain!!
---------- Post added at 01:57 AM ---------- Previous post was at 01:54 AM ----------
When mine was bricked i still had download mode, but had to use home with the 3 button combo to get into it, but i had no usb recognition, I still think you have download mode regardless, just some reason you cant get into it!!
It can be tricky, i know on tmobiles vibrant you had to plug in usb cord with batt out and do the button combo then put battery back in and it forced it into download mode!
I left the battery out all night last night, and held the buttons down for about 30 seconds without battery in to see if that drained the capacitors in the phone and still nothing.
Just going to have the manager at the Advanced Exchange store replace my device. I know her personally, so she will likely just swap with a New in box handset since it's totally out.
Related
I was flashing jackos s3 radio after the phone finished installing the update it will not start at all any fix for this previously it was stuck at htc screen did the task 29 and flashed the jackos rom will stay stuck at htc screen thanks
Is your device GSM or CDMA?
is gsm tried everything I could think of, I hope you have a suggestion the only thing that I found is the last resource is that riff jtag box ($150 plus shipping) but I don't have it, and I don't think is worth it for one phone.
Try...
Try flashing stock rom....i think hold volume down and press power button..go to bootload screen/ three color screen..
.then insert cable and flash stock rom
that is the biggest problem I don't get a bootloader screen or any screen any longer it seems like the the cellphone is dead, it tried holding the reset button with battery and without and it makes no difference, it just died after flashing the radio and I don't get a screen anymore I tried a different battery I have a separate charger, and it doesn't work either...
Not enough information to work with really, could you say more about the steps you took in this flash. There is a lot of help here on XDA but only IF enough is known. What you describe is not a common failure. Somethings been left out.
Just have to wonder if you were stock rom prior to the flash, were you unlocked, did the device operate properly before ANY flash was attempted ect....Not knowing were you started and the steps taken make it difficult, xda folks love fixing these things TELL US MORE !!!
PS I'm only here once or twice a month but really have gotten nothing less than the best help here when asked for with better information.
Let me see this telephone is not mine is from a friend that gave to me to fix it, the phone it was unlocked and on the bootloader screen it said security disabled I think something like that,
what it was wrong is that it was stuck on the htc white background
everytime you turn the phone on, I read some threads on how to repair this and found out how to get to the bootloader screen,
then I flashed, Rhodium-HardSPL_V2_00R3_185HSPL it completed and then rebooted, I flashed then Jackos S3 JackFULL 1.4.0, it completed 100% but I got the same error, I read on some thread that you somebody fixed that error by using task 29 so I flashed task 29 and then I flashed the same rom, it was stuck on the same htc screen so I checked on the rom folder there was another file recommended radio Radio_Rhodium_4.49.25.91 I flashed that file to see if it fixed the problem, but after it finished the phone turn itself off and did not start again,
then I checked the battery it had charge,
I tried a different battery nothing,
if I remove the battery slowly I see the red low battery light on for an instant
so the phone is getting power,
I pressed the power button and down button nothing
just the power button nothing,
tried holding the reset button nothing,
it is in a brick state,
is there any hardware mod for this phone,
I fixed a samsung captivate with a tool you created using a micro usb head some resistor in order to put it in a state called download mode,
the only thing I found on how to revive this is this box http://www.gsmserver.com/shop/gsm/riff_box_jtag.php the problem I don't have the money for it...
is that enough information? and of course the rom I use it was a gsm rom
I wonder if a hard reset would snap it into doing something...remove the battery, wait a couple of minutes, put the battery back in.. hold the talk and end buttons down and press the power button...I'm really not sure as I have not experienced this, but...I don't think anything would be a waste of time at this point
---------- Post added at 12:16 PM ---------- Previous post was at 11:52 AM ----------
oops...oh yeah...if the device does power on and you get a screen press the volume up next and see what if anything happens
that is right I have to try everything, but it didn't work but thanks anyway any suggestions I am still open to try everything...
I know you say the phone is GSM but...could you please tell us which, if any, carrier information the phone was designed for, and which rhodium version it is by looking at the sticker under the battery?
Ive been looking for a while into a solution for your symptoms and what Ive found thus far indicates a wrong radio was installed...CDMA radio to GSM device, or vice versa....there are people on this site who know everything, I am not one of them, but...it might be the case where you use MTTY...a low level type of command you can send to the phone via usb from your PC...I'm still looking...perhaps try looking too and cut the time in half lol...the low level commands can get to the device without it being in bootload screen...I think...as I said, I'm still looking for solutions
---------- Post added at 09:46 PM ---------- Previous post was at 09:10 PM ----------
read up on this...
http://forum.xda-developers.com/showthread.php?t=371154
and there's an example here
http://www.youtube.com/watch?v=4fQE0P3diKg
I'm not saying this will work and certainly dont try anything without reading up on the process in the first link
---------- Post added at 10:07 PM ---------- Previous post was at 09:46 PM ----------
I've been reading the thread of the link I posted, it's not relative to the Rhodium specifically, but still good reading until some Rhodium specific links can be found
i was running fc07 on my phone for the longest & yesterday decided to odin to fc15. the process got stuck during the modem part of it & took a long time (exceeding a half hour). i unplugged my phone & attempting to reboot it when the screen told me "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again." i proceeded to download Kies on my computer; however, when i get to the firmware recovery, it is asking for a code. i dont know what to do. Did i brick my phone? Is there a way to odin to a system recovery? i have tried fc05 & ek02 & i get the smae results.
Remove battery, Press AND Hold VolDown continuing to hold as you replace battery. It may feel awkward to do this.
That should get you back into Odin D/L mode.
I have the same issue. I upgraded to FC15 and after a full charge this am. I made a call, did some email and text, then BAM! nothing. no lights, can't turn on, can't get into DL mode, can't do anything.....
any thoughts?? I think I am outta luck here.
Yes. Just directed by sfhub.
And odin using his one-click odin after you entered to download mode.
http://forum.xda-developers.com/showthread.php?t=1551901
For me, I'm using sfhub's no-data version right now and no issues at all since it's released by him.
thanks, but as I stated, I can't enter DL mode.
I also tried pulling the battery and holding power down...
dsarch21 said:
thanks, but as I stated, I can't enter DL mode.
I also tried pulling the battery and holding power down...
Click to expand...
Click to collapse
You held Power+VolDown or just Power (as you replaced the battery)?
If that doesn't work, you should try a usb jig.
dsarch21 said:
I have the same issue. I upgraded to FC15 and after a full charge this am. I made a call, did some email and text, then BAM! nothing. no lights, can't turn on, can't get into DL mode, can't do anything.....
any thoughts?? I think I am outta luck here.
Click to expand...
Click to collapse
dsarch21, how did you upgrade your rom to FC15?
ok, what is a usb jig? sounds awesome.
I used odin to get to FC15
wait!!! OK, I got into DL mode, I must not have pushed power dn and power correctly....
thanks guys.....
ok now the phone wont power on. i put it on the charger for awhile & it still will not go into odin....it has a faint led light...any suggestions
Sent from my Xoom using XDA App
did you ever try vol down/up + power or just power with your usb cable connected to AC outlet?
yeah that didnt work...
Sent from my Xoom using XDA App
You may want to try to download mode keys either after inserting the battery and/or while inserting the battery. This might just get you back into download mode..
Also, how long did you have the phone plugged into A/C?
yeah...i kept the phone on the charger cuz i thought the battery was drained...it is giving a faint led light
Sent from my Xoom using XDA App
I hope you are using the original micro usb cable for odin or to change the battery.
If it is, for me, I don't have any more recommendation. Only customer service center would be your only hope. Be prepared how you are going to explain them!
---------- Post added at 04:26 PM ---------- Previous post was at 04:20 PM ----------
kobridge said:
I hope you are using the original micro usb cable for odin or to change the battery.
If it is, for me, I don't have any more recommendation. Only customer service center would be your only hope. Be prepared how you are going to explain them!
Click to expand...
Click to collapse
Or try to use different cable.
izan24 said:
yeah...i kept the phone on the charger cuz i thought the battery was drained...it is giving a faint led light
Click to expand...
Click to collapse
Depending on how long you kept it there - and how well ventilated it was - the phone could have overheated. There have been similar reports where all they got was a blue LED light.
Have you tried pulling the battery out, wait until the capacitors on the board run out (you'll see the LED go out) and then re-inserting the battery?
Hopefully this will help it come back to life - you could try a different battery as well but it may just be easier to take it to Sprint and have them replace at that point.
ok i got my wife's battery & it turned back on. now here is the problem i am running into. when i load the phone it says the firmware is not up to date....so i load it to odin & when i tried to do the odin fc15 restore, it gets stuck at the modem portion of the restore. what steps should i take from here?
Sent from my Xoom using XDA App
izan24 said:
ok i got my wife's battery & it turned back on. now here is the problem i am running into. when i load the phone it says the firmware is not up to date....so i load it to odin & when i tried to do the odin fc15 restore, it gets stuck at the modem portion of the restore. what steps should i take from here?
Sent from my Xoom using XDA App
Click to expand...
Click to collapse
let it be! if it does that with a blue line flowing across the xcreen let it be.
if ur there for a long time 10-20 mins. Well i dont want to tell you but someone else will. leave it til then. did u check md5?
Edit: Im not going to tell u something i am not 100% about so wait it out
i will let it be but definitely tell me if this doesnt work so i can figure out if a new phone is needed....what is md5 & where can i find it
Sent from my Xoom using XDA App
Well, since it's been a while hopefully you let it sit and finish flashing FC15. I noticed the delay as well and stood there in horror as I waited to see if I now held a $550 paperweight....
...but then came the "Pass!" indication about a minute later. I'll post my thoughts on this update separately.
So if you didn't, let it go all the way through and you should be all set. And glad that it seems it was just a battery - they're certainly easier (and cheaper!) to replace than the entire phone.
well i let the phone sit for hours & i didnt get a pass....without a way to at least nandroid to a backup, i chalked it up as a lost and filed a claim...will be getting the new phone today at work. if anyone is interested in playing w/a phone that i believe is bricked let me know...im sure i can get it off for a cheap price....lol say no to fc15....lol
Today I was in my car sitting in a parking lot, had my phone propped on my steering wheel with the txt app open when the screen when blue then shut down. I tried to power it on but it wouldn't come on, I pulled the battery hit the power button, the LG logo came up for a few seconds then shut off and the only way to turn it on again would be to pull the battery. Holding the power and volume rocker button down will turn it on to recovery. The phone is rooted so when I go to factory reset i've had 2 times it loaded to TWERP recovery but then the blue screen would come up again and I can't do anything. Most of the time it will end up in a green screen with the TC Crash, Demigod crash screen. Plugging it into my computer does load it as a device but I'm not able to access the phones storage. Has anyone ran into this issue and first question, is there anyway to recover data? Second question, is this a hardware related issue? I'm about to try and flash it back to stock since I can't get into TWERP but i'll wait for a response before I do that.
I tried to boot to download mode, I hold the volume up rocker and then plug in a USB, it shows download mode icon for a quick second but the screen goes black. I tried the LG flash tool but it doesn't get past step 1. Any one have any ideas i'm fresh out. Only new thing to report is sometimes instead of the green TZ crash i'm getting an orange RMP crash screen but with the same options as the green screen.
Need to know know a little more before I can reach my decision on where to start.
ROM
Kernel
Thermal mods
Was the phone hot?
Does it get hot upon starting?
Baseband?
I had this happen before but never to the extent that your explaining. Kind of sounds like a kernel panic.
DroidsOnRoids said:
Need to know know a little more before I can reach my decision on where to start.
ROM
Kernel
Thermal mods
Was the phone hot?
Does it get hot upon starting?
Baseband?
I had this happen before but never to the extent that your explaining. Kind of sounds like a kernel panic.
Click to expand...
Click to collapse
I can tell you what ROM it was and thats about it. Resurrection-Remix-LP-v5.5.8-20151027-vs985
Was running sold for months. Phone wasn't hot and didn't notice it getting hot at start up. Phone had 99% battery last time I checked before the blue screen.
I did some research about the LG G3 and blue screen and its a common issue from what i've found. No fix really
http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359 u could try this
TheMadScientist420 said:
http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359 u could try this
Click to expand...
Click to collapse
WOW, not sure about that. I'll see. Going to call verizon and see if they can do anything first.
Youll have to pay cause ure waranty is voided being rooted its a sure fire fix for almost all hard bricks and everything its not as bad as it looks i have had to myself on my g2 and g3
---------- Post added at 06:07 PM ---------- Previous post was at 06:02 PM ----------
Do u get the screen press up for dl mode. Try a bat pull and boot into recovery if possible
TheMadScientist420 said:
Youll have to pay cause ure waranty is voided being rooted its a sure fire fix for almost all hard bricks and everything its not as bad as it looks i have had to myself on my g2 and g3
Click to expand...
Click to collapse
Are you sure its a hard brick? From all the things i've read about this blue screen is its a hardware issue. My phone is showing up in the device manager under ports. Can I skip the first part?
Itsna kernal panick some people claim its from over heat others other issues if ure phonenshows up as qusb bulk or something like that then i believe u can the pin groung is to reset it to get it into bulk mode so from there u reflash all the primary gtp partitions then u can get to download mode to restore using stock tot. Ive nevernhad this issue happen but no its not technicly a hard brick but so far i cant find a solution but the method ive shown u usaully brings back all bricks and issues it could be a hardware issue but 9 outa 10 times its a software or firmware issue
---------- Post added at 06:20 PM ---------- Previous post was at 06:15 PM ----------
If u got usbbulk mode on com ports not step 4 but num 4 further down the page is where u start but u have to dl wilcracker and ure stock tot file
TheMadScientist420 said:
Itsna kernal panick some people claim its from over heat others other issues if ure phonenshows up as qusb bulk or something like that then i believe u can the pin groung is to reset it to get it into bulk mode so from there u reflash all the primary gtp partitions then u can get to download mode to restore using stock tot. Ive nevernhad this issue happen but no its not technicly a hard brick but so far i cant find a solution but the method ive shown u usaully brings back all bricks and issues it could be a hardware issue but 9 outa 10 times its a software or firmware issue
---------- Post added at 06:20 PM ---------- Previous post was at 06:15 PM ----------
If u got usbbulk mode on com ports not step 4 but num 4 further down the page is where u start but u have to dl wilcracker and ure stock tot file
Click to expand...
Click to collapse
OK thanks. I mean I guess I don't have anything to loose, so i'll give it a shot.
Like i said i couldnt find a solution im no developer ive just been rooting and modding since the first og moto droid ive bricked and fixed a lot of phones this may not be the proper solution i just no its work for a lot of people on a lot of diffrent bricks on both g2 and g3 i know basicly the g2 is unbri kable and sofar so has the g3 since this i wish it was a general sticky
---------- Post added at 07:07 PM ---------- Previous post was at 07:00 PM ----------
You can try calling lg but i consider there tecks dumber the crap but they get paid for what they do again 9 outa 10 times they cant help other than u sending it in for repair like i said ure rooted if they find out it is its fixed on ure dime i dont know no cell company has ever helped me out.
What do kind of wire do you suggest using?
I used acouple strands of speaker wire coiled up and a pair of tweezers to hold it end bent it to touch both so i still had a free hand
TheMadScientist420 said:
I used acouple strands of speaker wire coiled up and a pair of tweezers to hold it end bent it to touch both so i still had a free hand
Click to expand...
Click to collapse
This is impossible!
joel71 said:
This is impossible!
Click to expand...
Click to collapse
When u plug into ure pc what ports or coms. What xoez the fone shop up az
TheMadScientist420 said:
When u plug into ure pc what ports or coms. What xoez the fone shop up az
Click to expand...
Click to collapse
After trying for what felt like forever I got it kind of work once. It showed up as QCBATCH on port 6. But once I broke connection it went away and I wasn't able to get it to work again. I'll give it another try sometime today..
Sometimes it takes a bunch of trys
TheMadScientist420 said:
Sometimes it takes a bunch of trys
Click to expand...
Click to collapse
Got it working on the first try today. I used the SIM Card bay for a ground so I didn't have to hold it. Much easier, flashing now, will report back after.
joel71 said:
Got it working on the first try today. I used the SIM Card bay for a ground so I didn't have to hold it. Much easier, flashing now, will report back after.
Click to expand...
Click to collapse
Let me no how it goes
I did the steps but it still booted to a RPM CRASH screen, I couldn't get into download mode. I'm trying to flash Cache, System, Userdata, and SB1 now.
So after flashing a new 7.0 rom on the phone, I updated it via OTA. When it finished, instead of rebooting the phone, it led to a black screen. I have tried turning it on and opening bootloader/recovery but nothing has worked so far. When I charge the phone the white LED above the screen starts blinking and if I plug the phone to my pc and keep pressing the power button, it connects/disconnects from the PC every 20 seconds, so I know the phone is not completely dead. I don´t know what to do anymore, please help.
Its a hard brick you many of us have done it and for now there is no solution. If you check the other threads someone has claimed they figured out a way to boot in to bootloader to revive the phone I think the website is aryktech or something similar but haven't seen verification. Other than that its a paperweight.
---------- Post added at 07:28 AM ---------- Previous post was at 07:25 AM ----------
http://www.aryk.tech/2017/07/moto-z-play-unbrick-solutions.html?m=1
I had that problem on a OnePlus 3t. The battery was so low it would constantly try to boot when you plug it in. I put it on a turbo charger and left it. Eventually the battery got enough where I could get into recovery and boot.
Hello All,
I have been using Lineage OS on my rooted HTC One M9 for more than 6 months. Everything was working fine, only battery backup was not good(old Battery). A week ago when i pulled my phone out of my pocket, it was off, tried turning it on, didn't work. When connected to charger nothing happens, tried to go to bootloader/recocvery mode did not work.
After googling all this, i found about field test mode, that also is not working, tried.
Tried charging with stock charger, different charger, USB to laptop... nothing.
However, when phone is connected to laptop, windows 10 notification sound comes up but phone is not detected.
Seems like the soul has left the phone.
Please Help!!
Change out the battery. If that doesn’t work, it also sounds like the Motherboard went out.
Battery dead
The soul must be in sleep,is not dead but the battery is gone
R.I.P battery (we will miss you)
Change you battery dude
;( can't upload pic of problem "network error"
I'll got 4x HTC m9 from an ex HTC employee and he told me one of them had a problem and he wasn't sure really what the problem was but he told me the phone keeps rebooting, so I thought wellllll I flashed like every single galaxy from 1 to 10 and ofcourse i faced some times i did got it semi bricked but after moments of rage and eating excessive amounts of instant noodles I was always luckily able to fix it. Now this m9 says on the screen
Blackbox: Software status modified
Pink: locked
Orange: s-on
Pink : security warning
Got 4 choises
Reboot
Reboot to bootloader
Boot to recovery
Power down
Now all of these options don't work... even power down will reboot back to this screen and recovery option gives message that it's a development version.
Some people claim it's fixable by sending RUU? With Odin or boot.img other story's saying EMMc bricked.. since xda is the only place where I can actually get an answer from people knowing what they are talking about.. is it dead? If it's not I just put some more time in it.. at least the phone gets detected by my PC when my s6 edge had a eMMC brick it would show up as (no USB id for devicediscriptor...
influenza026 said:
;( can't upload pic of problem "network error"
I'll got 4x HTC m9 from an ex HTC employee and he told me one of them had a problem and he wasn't sure really what the problem was but he told me the phone keeps rebooting, so I thought wellllll I flashed like every single galaxy from 1 to 10 and ofcourse i faced some times i did got it semi bricked but after moments of rage and eating excessive amounts of instant noodles I was always luckily able to fix it. Now this m9 says on the screen
Blackbox: Software status modified
Pink: locked
Orange: s-on
Pink : security warning
Got 4 choises
Reboot
Reboot to bootloader
Boot to recovery
Power down
Now all of these options don't work... even power down will reboot back to this screen and recovery option gives message that it's a development version.
Some people claim it's fixable by sending RUU? With Odin or boot.img other story's saying EMMc bricked.. since xda is the only place where I can actually get an answer from people knowing what they are talking about.. is it dead? If it's not I just put some more time in it.. at least the phone gets detected by my PC when my s6 edge had a eMMC brick it would show up as (no USB id for devicediscriptor...
Click to expand...
Click to collapse
Well,i am not a development or something like that but my idea is(not a good idea but anyway) it seems that you have to download a little lot of Rom's and if non of them works it is a refurbished item from Htc.co (this is my opinion)
For better answer(of course that have intelligent people than me)you better ask them privately
---------- Post added at 12:56 PM ---------- Previous post was at 12:55 PM ----------
Can you give me that broken Htc?
ford1234 said:
Well,i am not a development or something like that but my idea is(not a good idea but anyway) it seems that you have to download a little lot of Rom's and if non of them works it is a refurbished item from Htc.co (this is my opinion)
For better answer(of course that have intelligent people than me)you better ask them privately
---------- Post added at 12:56 PM ---------- Previous post was at 12:55 PM ----------
Can you give me that broken Htc?
Click to expand...
Click to collapse
Unable to flash rom trough RUU always get message the battery is below 30% and that cannot be true.
influenza026 said:
Unable to flash rom trough RUU always get message the battery is below 30% and that cannot be true.
Click to expand...
Click to collapse
Of course not that is true