Hi, calling all Singaporean DHD users here! I'm having a problem :X
I'm intending to send my phone for warranty tmr, because my screen suddenly has a blue tint to it. So as i'm looking for the proper RUU to use, my phone screen went off. totally everything is black. I can boot (hear the custom bootsound)but it's black everywhere. Major screen hardware issue i guess. But! This makes it so difficult for me to even do a factory reset since i cant make the steps without even knowing which button i'm hitting on a practically blank screen. I was thinking if anyone of you has went back for warranty and is there a particular RUU i can request for? As far as i know, RUU can be install via the PC right?
Really really appreciate any help here for this Poor DHD dude T_T
So,
You create a thread in the Development section. I move it to the General section. You then think its wise to create a duplicate thread in the Q&A section.
Thread Closed.
Related
I bought a 2nd hand XDA Orbit with all the correct software and that. I've had a problem with it before, nothing a good hard reset couldn't solve. But today, I did exactly the same thing for a hard reset, and now doesn't go past the O2 screen and just goes black!
I cannot hard reset again, and I cannot go into the bootloader (hold power + voice thing on the other side, push the reset with stylus and let go while still holding the buttons on either side). I'm rather scared I've bricked the device, but I am sure the previous owner did not load any unofficial ROMs and I haven't either and I still have the original WM2003 CD. Wouldn't be a problem if I eventually had to go to an O2 shop would it? Lets hope it can be sorted! And seeing as quite a few people have had this with varying degrees of sucess, I fear my luck may be out with this thing .
I hope someone can point me in the right direction.
Oh and I don't think my device i CID unlocked, does this matter?
Thanks in advance x
fixed
mods..can u please delete this now pointless thread!
it was down to my own stupidty...so thank you for the people working on a response...well if you were!
Hi all,
I tried doing a search on this before posting this thread. No luck. I just got my TP2 on sunday. I let it charge and flashed HardSPL and a few roms. I noticed my phone would turn completely off when I open and close the screen. At first, I thought it was the display turning off to save power, but the phone is actually turning completely off and I need to hit the power button and boot it back up again. Is this a setting I need to change? Or could there be something wrong with my phone? I also tried going back to the stock rom to eliminate that as a cause and the same thing happens.
Any help is appreciated.
I have posted an almost similar question here with no reply.
http://forum.xda-developers.com/showthread.php?t=553378
Not sure what the problem is. In my case the solution is not to close the keyboard when OneNote Mobile is still open!
My colleague is having the same prob, from what he is experiencing, i would suggest a hardware fault, probably just a loose ribbon cable... but best send it back to HTC to avoid voiding your warranty
palatkik said:
I have posted an almost similar question here with no reply.
http://forum.xda-developers.com/showthread.php?t=553378
Not sure what the problem is. In my case the solution is not to close the keyboard when OneNote Mobile is still open!
Click to expand...
Click to collapse
I don't OneNote is my problem. Since I don't use it.
rosebud said:
My colleague is having the same prob, from what he is experiencing, i would suggest a hardware fault, probably just a loose ribbon cable... but best send it back to HTC to avoid voiding your warranty
Click to expand...
Click to collapse
I guess it's time to give TMO a call. Just need to flash everything back to stock.
Thanks for the suggestions guys. I was hoping to avoid having to send it back, but i might as well.
Albaholic said:
Hi all,
I tried doing a search on this before posting this thread. No luck. I just got my TP2 on sunday. I let it charge and flashed HardSPL and a few roms. I noticed my phone would turn completely off when I open and close the screen. At first, I thought it was the display turning off to save power, but the phone is actually turning completely off and I need to hit the power button and boot it back up again. Is this a setting I need to change? Or could there be something wrong with my phone? I also tried going back to the stock rom to eliminate that as a cause and the same thing happens.
Any help is appreciated.
Click to expand...
Click to collapse
Hi,
I had this issue to and send the phone in for repair. The said that it was a problem with the mainboard - replaced it and send it back. It now works perfect.
REMEMBER!!! If you want to send the TP2 in for repair you must reflash the SPL back to the original one, I think it is 0.79.0000 (see http://forum.xda-developers.com/showthread.php?t=550131 for how to restore to the original HardSPL)
discoverd the same issue, happened to me about a week ago for a few times, when i slide in/out the keyboard. It just habbend about 4 times, but didn't happend again since this time ... i will have a eye on it...
Same here. The screen turns off completely but the phone actually works and I can receive or place calls. Called the HTC support and they advised to try if a hard reset will fix it before sending the phone in. The tricky part here is that this issue can not be recreated easy in their service as it happens randomly with me (sometimes it works fine for days). I am still trying to find out what causes this issue on first place. I think it started right after I installed IGO 8 and changed some power settings in the ini file but it kept doing this after I removed it. I also tried to disable the light sensor (the one that turns the screen off when you place the handset to your ear during a call) because it looks exactly like this - screen turns off but the phone works. So, I will give it another week and I will try the hard reset.
What roms do you guys have this issue with? I am using the stock T-Mobile US with HardSPL.
wejergang said:
Hi,
I had this issue to and send the phone in for repair. The said that it was a problem with the mainboard - replaced it and send it back. It now works perfect.
REMEMBER!!! If you want to send the TP2 in for repair you must reflash the SPL back to the original one, I think it is 0.79.0000 (see http://forum.xda-developers.com/showthread.php?t=550131 for how to restore to the original HardSPL)
Click to expand...
Click to collapse
Did they replace the entire phone or just the mainboard?
ma6inista said:
Same here. The screen turns off completely but the phone actually works and I can receive or place calls. Called the HTC support and they advised to try if a hard reset will fix it before sending the phone in. The tricky part here is that this issue can not be recreated easy in their service as it happens randomly with me (sometimes it works fine for days). I am still trying to find out what causes this issue on first place. I think it started right after I installed IGO 8 and changed some power settings in the ini file but it kept doing this after I removed it. I also tried to disable the light sensor (the one that turns the screen off when you place the handset to your ear during a call) because it looks exactly like this - screen turns off but the phone works. So, I will give it another week and I will try the hard reset.
What roms do you guys have this issue with? I am using the stock T-Mobile US with HardSPL.
Click to expand...
Click to collapse
Did you ever resolve your issue? i ask because I am having he same problem on a Sprint Touch Pro 2
coppertop24 said:
Did you ever resolve your issue? i ask because I am having he same problem on a Sprint Touch Pro 2
Click to expand...
Click to collapse
Sorry, forgot to update this thread. I ended up getting a replacement from TMO. I am much happier now that my phone doesn't turn off whenever I close the screen. Get a replacement while you can and ask them nicely if they can overnight it to you. I did.
Actually, this was a software problem in my case - I did the hard reset 2 weeks ago and since then I have not experienced the issue. I am going to start installing my previous programs one by one to find out what caused the problem.
Same
I have the same problem,
The hard reset solve the problem?
please heeeeelp
Hi,
Right in the middle of use, my ATT Tilt 2 went to a basic, dead screen with red, green, blue, and white bars that says Rhod300 32m SS-BC, etc.
The operating system seems have gone down--it won't respond to anything. Hard reset produces the same results.
Can I flash a cooked or official Rom back onto this? I think activesynch is needed for a normal flash and of course I can't use active synch with the phone in this condition.
I think probably what I need is an original ROM install. Is this possible with a normal Windows 7 PC and a dead phone?
I have so many Windows Mobile programs and peripherals that I am trying to avoid going to Windows Phone at all costs--at least until they have basic stuff like file systems, a way to port over notes, etc. Also need a hard keyboard.
Right now using an older Fuze, which works, but is slower, worse screen, smaller, and lacks some of the features I like.
Thanks for your help.
You sound like you're in the bootloader mode. Tri-color screen.
You can flash from USB or from SD at that screen. I'd recommend trying to flash a stock ROM - as it flashes everything. Assuming that works, hopefully you can flash back whatever ROM you were on.
The phone isn't dead if you're at the tri-color screen. It should say 'serial' at the bottom - when you plug in your USB cable, it should say 'USB' and install some drivers. Then with the RUU software that comes with every ROM, you should be able to flash it.
Phone won't reboot--stuck on tricolored boot screen
Hi,
Thanks so much for replying. I appreciate you pros helping us novices.
Just after I posted the first note, I pulled the battery and hit the power button, it rebooted, and everything was still there in the OS--working fine. But whenever the device had to be rebooted, I would have the same problem of it getting stuck in the boot screen. After that, for the last several days once in awhile, randomly, it would finally reboot from the boot screen after I pulled the battery and hit the power button. The rest of the time (about 5/1) it would just sit there in the boot screen no matter what I did. The "Serial"/"USB" thing would change when I plugged it in, but that's all.
Thought it was the OS, so at a lucky moment where the "pull battery, hit power button" strategy actually worked, I installed the latest official HTC/ATT Rom--it's the next to last one issued that ends in .4.
It was gorgeous and I got all excited--started installing stuff thinking my problem was solved.
Had to reboot to install some programs--now it is stuck again on the boot screen. Tried 30x again--no luck with the "pull battery/hit power button"
strategy. Sometime it would flash a white screen really quickly saying something like "Can't read image!" before going into permanent boot screen. The boot screen will switch from "Serial" to "USB" if you connect it to the computer. So, the problem doesn't seem to be in the OS--rather, in the ability of the device to "read" the OS from the boot screen.
I would be grateful if you or anyone else may know what's going on here, and any ideas on how to fix it. Is there any manual way to get it to read the OS from the boot screen when that's not happening?
I have two guesses (both of which may be wrong):
1. It may be something in the hardware is just worn out and is less and less able to read the Rom--any ROM. I got the phone new off Amazon for a profit of $50 ($.01 cost plus a refund for an older phone) in the summer of 2010 when it was already outdated. and WP was replacing WM. I've certainly gotten my money's worth after 18 months!
Of course we now know that a brand new ROM has the same problem as the older one--which suggests to me it's in the hardware. I'm sure the new OS and the stuff I installed is still there on the phone, but something it appears is not reading something in order to allow the boot up.
2. I have a squirrely free program called Rax Reset (from Windows Mobile Marketplace) that does a software-based hard or soft reboot from inside the OS. The very last time the device went down and didn't come back up, I had used that program to soft reset it. Might have been a big mistake. Could this program be causing the problem? If so, just one reboot would allow me to get rid of it or even hard reset to remove everything but the new OS--but can't get it to boot.
If it turns out the phone is just worn out, I've certainly gotten my money's worth.
I still love WM even with all its problems--and especially the newer Sense version. If this one is shot, I'm thinking about just buying a new Touch Pro2 on Ebay to avoid all of the sacrifices and backwards steps involved with Windows Phone.
Thanks for any help anyone can provide.
Phil Butin
Why are you crossposting? I read this EXACT same post in a thread just below this, in the same section. That's pretty low.. Crossposting across forums isn't welcome, crossposting within forums IN THE SAME SECTION is definitely not welcome.
Don't do it again.
Sorry, just trying to get help
Sorry, just trying to get help, not that familiar with the rules.
I searched on "bootloader" and found a thread (wrote a comment there too), but it's old....
Here is the thread. It doesn't really provide any solution.
HomeArrow
Legacy & Low Activity DevicesArrow
HTC Rhodium: Touch Pro2, Tilt 2Arrow
Touch Pro2, Tilt 2 GeneralArrow
issues with bootloader.
Either way, whether you know the rules or not - why would you think copying and pasting the exact same words in the exact same forum help you any more...
Anyhoo, have you tried the usual? Flash stock? Sometimes I've heard you have to flash several times, I never really understood that logic tho.
I'll try to reinstall the HTC/ATT Sense OS again. I guess you're saying active synch doesn't need to be working in order to do that. I'm at work now--have to wait until i get home. Nothing to lose at this point.
But I'm seriously wondering whether the problem is the OS install or whether there is something in the device that is supposed to read the ROM and start the bootup that is just wearing out.
Thanks.
"No Image File"
The quick little flash of white screen has "No image file" in blue letters--goes by so fast you can hardly see it.
[email protected] said:
The quick little flash of white screen has "No image file" in blue letters--goes by so fast you can hardly see it.
Click to expand...
Click to collapse
That error message is 'normal'. Basically the phone checks the SD card for a file labeled "RHODIMG.nbh". If said file exists, it will flash from it. If no file exists, or no SD present - it continues loading bootloader and should say "Serial" at the bottom. This indicates that it's ready to be flashed. If you plug in your USB cable, it will install some drivers and then it should change to "USB" at the bottom instead of "Serial".
Now you should be ready to flash from a normal RUU. I would recommend flashing STOCK, because this flashes everything.
It might also be good to note a lot of people have experienced something similar - the phone getting "stuck" in bootloader mode, and only occasionally making it to WinMo. I'd guess it's failing hardware in some way shape or form, as none of my RHOD's or RAPH's have ever done this.
Good News--at least for now
Good news--I hooked it up to the computer with the USB cable for awhile and the Windows 7 computer did set up some drivers. For some reason after I disconnected it I reset it, and the reboot worked. Then I immediately uninstalled the squirrely reset program and removed it.
Everything I installed yesterday is working fine--I have soft reset it about 5 times now and each time it has rebooted. So I think maybe I'm back in business. Too soon to tell--but we will pray and keep our fingers crossed.
Thanks so much for your time and help. I don't know how to use the thanks meter but I would have if I could have.
[email protected] said:
Thanks so much for your time and help. I don't know how to use the thanks meter but I would have if I could have.
Click to expand...
Click to collapse
You're welcome. Basically if I or someone else posts something helpful, click the "Thanks" button under that post.
15 hours later, Tilt 2 is still working fine on the newly installed Sense OS. I have rebooted freely (using the stylus button on the side) since removing the program "Rax Reset," and everything seems to be going well. I'm keeping my fingers crossed, and will end my contributions to this thread with a warning about using "Rax Reset."
Thanks to all.
Hello, I don't know much about what i'm doing guess u can call me a virgin to the modding game. I'm a blackberry user so please bare with me. I'm thinking about joining team droid and I found my moms old HD2 lying around. It was having problems (un responsive touch screen) and I managed to find a place to fix that. I walk out the repair shop and start driving home and the phone is rebooting itself, stuck on a screen that says NRG Energize. I'm guessing whoever gave it to her had a rom installed? Now i tried holding down the volume down button and the power button, and also holding down the volume down button while pressing the reset button on the back but all that does is bring me to a multi colored screen that doesnt go away and reads:
PB81120 HV B3
SPL-2.08. HSPL 8G XE
'
can anyone, if anyone tell me where do i start in fixing this problem? any helpful links? advice on if i can get passed this, if theres a better rom out there and how i would go about installing.
please and thanks in advance. sorry if i am posting wrong or if theres another post i should be looking at, any guidance would help.
Armani_X said:
Hello, I don't know much about what i'm doing guess u can call me a virgin to the modding game. I'm a blackberry user so please bare with me. I'm thinking about joining team droid and I found my moms old HD2 lying around. It was having problems (un responsive touch screen) and I managed to find a place to fix that. I walk out the repair shop and start driving home and the phone is rebooting itself, stuck on a screen that says NRG Energize. I'm guessing whoever gave it to her had a rom installed? Now i tried holding down the volume down button and the power button, and also holding down the volume down button while pressing the reset button on the back but all that does is bring me to a multi colored screen that doesnt go away and reads:
PB81120 HV B3
SPL-2.08. HSPL 8G XE
'
can anyone, if anyone tell me where do i start in fixing this problem? any helpful links? advice on if i can get passed this, if theres a better rom out there and how i would go about installing.
please and thanks in advance. sorry if i am posting wrong or if theres another post i should be looking at, any guidance would help.
Click to expand...
Click to collapse
This should probably be put in the HD2 Android NAND Development Forum of the HTC HD2..... but I'm gonna help you anyway!
First you should look at this: http://forum.xda-developers.com/showthread.php?t=1021837 read it and study it GOOD!!
Then choose a rom from here: http://forum.xda-developers.com/forumdisplay.php?f=928
Use the instructions from the first link to flash the new rom.
Thanks, prior to reading this i was able to get the stock rom from t-mobile and load it up from my sd card. Now my issue is if it starts up it freezes during set up and goes into a bootloop or it just goes thru a bootloop when i turn it on. I guess the first step (from what i've read today) is when i get home to check the battery pins? not even exactly sure how they are suppose to look but i'll mess around with them (hopefully they dont break) when i get back home... i'm at work unable to focus thinking about fixing this phone lol.
I didn't know where to post this question since the phone I'm going to refer to is not listed anywhere... It's P350 from LG. It has a really weird problem. From the moment I bought it (some months ago) it keeps entering emergency mode or close and either reboot either not reboot or even it gets stuck anywhere when used or not used randomly with no apparent reason for it to do so. I tried to return it in factory settings more than three times already, while I'm running it without the SD card and I can't understand if there could be a solution or I should take it to service. Any help would be appreciated.
Moved to LG P350 forum, as per OP request - thanks
Maybe you can go back to the shop and ask a new one?