Develop Bugs

[Q] USB death after Root and Flash on Xperia ARC

HI all,
I flashed my Arc last night, and then rooted it.
All seemed to be fine, until I rebooted after the Root had been completed.
Once the phone turned back on, the battery had dropped from 70% to 1%. It was warning me that it was about to shut off, so I tried to plug it into the computer, via USB cable to charge, and nothing!! I thought it must just be my computer, so I tried to plug it into the wall socket, and still nothing! It just refused to charge. Full stop. However, it continued to tell me that I was bout to run out of charge and didn't turn itself off!!! I unplugged it 1000 times, and still tried each option ( computer/wall socket) and it just wouldnt work.
So, basically, this is a well known problem and you can solve this by following this procedure -
" try removing the battery for a few seconds then reinsert the battery whilst the wall charger is plugged in. give it 5 mins before attempting to switch it back on.
if it manages to switch back on, try to put the phone in flight mode until the red light turns a pale green. "
I did this, and turned it back on. Straight away the phone rocketed back up too 77% battery.
And, the usb port worked again.
So my question is this,
Is this a common issue?
And is following the above process ok for the phone? I hope that I wont have to send it back, cause the other people on that link above had too.
Is anyone else had this problem?
Thanks all for your input
Amanda

This is a common issue, no worries Amanda! Same for me when I flashed the UK Generic 2.3.2 to obtain Root..

How did you fix it???

This happened to me also last time after a reflash. You may try to do a complete drain then do a complete full charge (don't turn on the fone while charging at this time).
Sent from my LT15i using XDA Premium App

Just remove the battery and wait a few sec.
Sent from my LT15i using XDA Premium App

Problem with ROM now I can't charge

I installed the ARHD 7.0.0 ROM on Monday everything was working fine, I also installed the SMooth Rosie MOD and still everything was fine. But today, I lost my phone signal and though oh well i'll leave it whilst I go to the gym, I came back and the bttery ws at 23% (Was at 91% when I left it).
I rebooted the phone and it would get to the lock screen (with no ring) then it would reboot and it constantly done that. I reset everything and formatted everything, I transfered the ARHD 7.0.0 back onto the phone but as I was trying to flash the image, from windows, the battery died, I can't seem to charge it.
All its doing at the moment is flashing the red LED. I tried resetting the LED with power presses in and Vol but it keeps coming back after a few seconds.
I really just need to know how to charge the phone, once its charged I will be able to sort it out. Oh and I can't even turn the phone on at the moment.
Thanks in advance.

Sounds like you didnt instal the boot.img
EDIT: put it in the wall charger for 10-15 minutes and dont touch it...

I put it in a wall charger and its stopped blinking. Cheers
Oh and I did install the boot image on Monday, i've been using the phone for two days, then it just lost the signal and then didn't work. Weird!
Thanks again!

Yeah....just pluggin usb charger and leave it for ~1h and U will see, it's charging.
Few days after buying HOX I was on a party with enabled wifi, async, gps ect. Lately this night my phone goes off and I wasn't able to turn it on. At home I plugged in charger but there was no charging led.
Yeah...thougt the new phone was bricked.
With plugged usb I just left it for ~1h and then...TADAA!...charging led!!!

Well tried charging it with the wall charger. At first the light when solid, I returned to it 2 hours later and the light was off. Tried to turn it of and its blinking again, I can't even turn it on Arghh!!

My G2 will shut itself off - any suggestions?

I'm looking for any ideas for the problem I'm having on my G2. I'm afraid it's a hardware problem and not much I can do about it.
I started having problems after upgrading from CM 7.1 to 7.2, but I don't think it was related to the upgrade. I started having battery draining problems, the phone took forever to get fully charged, and car mode would automatically start sometimes when plugging up or unplugging the charger. I cleaned the usb port with alcohol (with battery removed), let dry, and restarted. Now I don't have the car mode problem and the battery problem is somewhat better.
My problem now is that the phone will just die when I'm using it. Usually when I'm using the browser. I'll be scrolling on a page and the phone will just turn itself off. Like the battery died. I can turn the phone back on and it will start up, get all the way started back up, but while it is still loading the home screen widgets, it will go off again. I can repeat this several times. The only way to recover is to plug in the charger. I don't have to hit the power button again, just plugging in the charger will start up recovery mode automatically, I'll choose reboot and the phone will start normally then and stay on.
The phone never dies when I'm not using it. I'll carry it all day, making phone calls on and off, and it'll stay on with no problem. Mostly, I only have the problem when using the browser. Also had the problem while using my newsreader. Once during playing a game. But if I start up browsing the internet, it doesn't take long before it will turn itself off. A matter of a couple of minutes. I don't have the problem with reading emails with K9. Don't have a problem in downloading from the internet such as podcasts. Don't have a problem in sending text messages. Don't recall it shutting down while using the Facebook app. After putting up with this for a week, some troubleshooting and observations.
I never have this problem if the charger is plugged in. Only when it is running fully from the battery.
I've tried swapping to a different battery.
Turned down the overclocking with no difference.
I've changed to other recoveries, CM 7.2, CM 7.1, a CM 7.1 that I was running in May. No difference.
I've swapped memory cards.
I've reset battery stats.
No difference if running on wifi or just data.
Clearing caches made no difference.
So, I start thinking it must be a hardware problem, but then why does it only crop up when internet browsing. Must be power related since plugging in the charger makes it go away, but why does it not have a problem with using the phone in other ways?
Any suggestions on what I could try?

You could try to see if there is too much voltage drop when you start something power-hungry. Use a battery voltage logger and post the results. Start logging, let the phoneidle for a minute and then start browsing. Even if the phone shut off, the log should still be there after rebooting.

Thanks for the idea. I can't locate a logger that looks like it would work. It would have to capture a quick drop in voltage that is momentary. This problem happens even on a full battery and when the phone come back on (either momentarily or after a recovery reboot) the battery level is unchanged.

You might try as well an other way: first idle, then gradually step up to a more power hungry app to see when the problem actually happens. I have no other ideas...

Make sure that you dont have any contact with the battery and the door.
Normally batteries are covered with an aluminum wrap, and can cause short-cuts with the phone itself.
I searched it for a while with the galilio batteries.
You can try to put some saranhwrap around the battery.

I have the same problem with two different batteries. But I'm ready to try that too.

Battery graph
So here's a graph of my battery status. Long time to charge to 100%. Discharges pretty rapidly. Each downturn ends in the phone turning itself off. Notice that at 7:30 today, it turned itself off, I did a recovery reboot, then noticed it wasn't charging very well (green line turns to blue but doesn't increase), then I did a manual reboot and when the phone restarted, it showed the battery was at 100% charge (from about 60% before the reboot).
What do you think - hardware or software?

oVeRdOsE. said:
Make sure that you dont have any contact with the battery and the door.
Normally batteries are covered with an aluminum wrap, and can cause short-cuts with the phone itself.
I searched it for a while with the galilio batteries.
You can try to put some saranhwrap around the battery.
Click to expand...
Click to collapse
Well, I just took the cover off for awhile and tried it. Played crosswords (Shortz) for awhile with no problems. Started my newsreader (Newsrob) and it shut itself off in about 15 seconds. So, no short to the battery cover.

Same thing is happening to me. I use poweramp or the browser and the G2 just shuts off. Then I restart it and it tells me that the battery is low. Once I shut it down and reboot in recovery and wipe the battery cache it's back to it's normal battery level. I disabled data and set my phone for 2G networks only and it didn't shut off after. I'm assuming this is a wireless issue? I'm running mimicry 1.3.0 on my G2.

Had the same problem. Swapped out batteries and problem gone.
Sent from my HTC Vision using xda app-developers app

Did you swap the battery and immediately have no further problems? I tried swapping my battery already and still have the same problem.

[Q] [q] Hard bricked? Won't turn on, won't connect, small signs of life

Hi,
I turned my phone off last night before going to sleep, it had 40% battery left. When I tried to turn it on this morning it didn't do anything. Even when trying to charge it the LED did not light up.
the only sign of life I got out of it was a screen with the "battery charging", looked like it was charged around 50%. However, it did not, and still does not respond to the hardware keys...
Any solutions? Or am I simply out of luck.
Extra info:
Stock rom, rooted.
Already had some sort of problem described in this thread: http://forum.xda-developers.com/galaxy-note-2/help/phone-freezes-awake-stock-custom-rom-t2908503
Thanks in advance!

May be you should try wiping data (lock screen & stuff) from samsung online site (if you have registered).. Not sure if it work.. Just a suggestion..

Somehow I don't have any registered devices.. (I did register it though, just because of the dropbox storage bonus)
Edit: My device randomly booted up, had it plugged in to the charger all day (about 6 hours), 47% charged right now.
going to make a backup using titanium and flashing stock via odin, see if it helps.
This is reaaally weird though... :silly:

[Q] Can't boot up SmartWatch 3

Guys,
I've updated my SmartWatch 3 to 5.1 yesterday via OTA
Everything worked fine.
When battery was low, I charged it up from 9% to around 80% (I switched it off though)
It stuck charging at 80% as it was very hot I removed it from charge.
After 2-3 hours I charged again to complete from 80% to 100% even after 1-2 hours of charge It would not charge.
Today morning I did the same I wouldn't charge. I switched on the watch I got android wear logo and it directly switched off.
Now it's not switching on.
Any help I can get?

Yeah same issue here but it is harder than that ...
I installed TWRP on my watch, and when I received the 5.1 OTA, it seems that it did not want to install the update because I was not on recovery stock. Then, my SW3 started to lag, I was not able to install the ZIP via TWRP, and it was superhot, I was unable to boot Android Wear..
That's so ****ed up, man. I can't even know what should I do. xD

I've got the same (or really similar) problem my watch was out of battery, I put it on the charger, it showed normal charging battery icon, then when I tried to turn it on it doesn't show anything, the display is black and when I held down the power button it vibrated once. The problem is that it isn't only display fault because I can't connect to the watch with my mobile phone. Wat do?
---------- Post added at 06:43 AM ---------- Previous post was at 06:38 AM ----------
Mavi222 said:
I've got the same (or really similar) problem my watch was out of battery, I put it on the charger, it showed normal charging battery icon. When I woke up the watch was extremely hot and then when I tried to turn it on it didn't show anything, the display i black and when I held down the power button it vibrated once. The problem is that it isn't only display fault because I can't connect to the watch with my mobile phone. Wat do?
Click to expand...
Click to collapse
edit: Well that was weird, I unplugged it from the charger and put it there again and now the charging icon is back and when I pressed the button it started to boot. Weird.

Me, too.
After OTA today, my watch is dead. Even long press power button can make freeze screen reboot.
sharukhmohammed said:
Guys,
I've updated my SmartWatch 3 to 5.1 yesterday via OTA
Everything worked fine.
When battery was low, I charged it up from 9% to around 80% (I switched it off though)
It stuck charging at 80% as it was very hot I removed it from charge.
After 2-3 hours I charged again to complete from 80% to 100% even after 1-2 hours of charge It would not charge.
Today morning I did the same I wouldn't charge. I switched on the watch I got android wear logo and it directly switched off.
Now it's not switching on.
Any help I can get?
Click to expand...
Click to collapse

Okay guys, here my solution, it worked for me :
If the screen of your SW3 is completly dark:
1) Just let it plug. In fact, the watch is charging, it's just not shown up (I dunno why...)
2) Let it like that for 1 hour, and then unplug it and let it cool down for 10 mn.
3) Install the Sony Companion App on your PC.
4) Keep ressing the power button of your watch til a screen with the watch and USB appears.
5) Plug It to your PC, open the Companion App.
6) Somewhere in the menus, you can resinstall the OS of the watch, RESET it, find the menu.
7) Let your watch restart.
And you're done ! It worked for me, so try.

I left it aside from morning to evening. Didn't even touched it. It completely discharged. So I kept to charge once again and it magically booted up and now working fine. Seems pretty weird. ?
Sent from Galaxy Note II using XDA Premium App

As I read in other post, I can confirm there is some kind of bug when you are charging your SW3, if you turn it on with the usb cable charging and the screen showing the battery %, the smartwatch gets like frozen and doesn't do anything.. In case you have this problem, you should wait until the battery goes to 0%, start charging your sw3 BUT when you are going to turn it on again first unplug the usb cable and wait until the battery % display dissapears.. I did it after I read it in other post in XDA (I don't have the link here.. I was searchig for it on another computer) and worked for me.
I hope it works for all.. sorry if my English it's not perfect hehe
I found the link: http://forum.xda-developers.com/smartwatch-3/help/smw3-wont-start-t3192354