this may seem paranoid but is there plugs that actually "shut off" the microusb input so that dust won't get in?
I saw people have it for their iphones.
I bought these in black. Fit well, but I ended up not using them because the rubber cover itself ends up becoming a dirt magnet.
apparently I can't post links yet so just search for "usb dust cover galaxy" on ebay
Related
Ordered a new digitizer for my Samsung Epix and it is the correct part and the digitizer just sits in the bezel, I assume its glued on but cant figure out how it comes off. Anyone done this before on this phone or have a tutorial or how-to?
Thanks
Mike
Just did it today. Wish I'd taken pics. You have to take it completely apart in order to connect the new ribbon cable as it attaches to the underside (bottom) of the circuit board. There's 6 screws that need to come out, the bottom 4 being obvious and the top two hidden, one under the stylus, the other under a rubber plug at the top rt corner, which you just pry out to reveal the screw head.
Once the screws are out, use something plastic to separate the case halves, I used an old credit card and started prying beneath the memory card slot. Then you can see the little ribbon cable on the bottom right side of the circuit board, folding around from the front. Be VERY careful when removing the ribbon cable from the board. You have to lift a small latch upwards and to the left , ending up with the little flap like lever standing straight up , to release the cable. The cable goes back in by inserting it and closing that lever to sandwich the cable in place.
The digitizer is held in by two sided tape that you may or may not be able to reuse. You will have to carefully pry it loose from the front bezel. I suggest you warm it with a hair dryer.
I had to use silicone gasket sealer on mine to hold it oin place as the sticky stuff came off with the digitizer.
Good luck !
Picked up this case at a Sprint Corporate store for 35 bucks and could not be happier.
http://www.freshfiber.com/products/galaxy-s3/
It is the Grey Macedonia case which is some sort of birds nest inspired look.
The outer part of the case kind of has a flex to it, just the right amount of give when you sit your phone down.
One thing I noticed at first which threw me off was the fact that the bottom of the case didn't have a hole for the bottom mic, but after further inspection it actually sits away from the body of the phone and kind of channels the mic next to the charging port, if that makes sense.
Nobody has ever complained about not being able to hear me since getting the case.
Solid corner protection, doesn't add weight to the phone at all (case itself weighs 16.8 grams) and has good lip protection on it for times when the phone is face down. I have a screen protector but just a cheap one I got that only covers the screen so I don't know how it may fit with some of the full screen protectors, but it does appear to have a bit of room to not affect them.
The best part?
That this case is 3D Printed and beautiful, and according to the packaging, the Grey and White cases can be put in the dishwasher for cleaning!
The one bad thing.
The back of the phone gets a little cruddy from being exposed.
Rearth Discover Wallet Case Review
Im a little surprised that no one has done a review of this product for the Nexus 5 yet but its hard to plop down a good chunk of change for a phone case especially if the point of getting said phone was because it is a bargain. I usually don't buy cases which cover the phone completely with a flap (wallet style) but I really love my Nexus 5 and this case looked like the best I could find and at around 50 bucks I hoped for the best...
The Box
Sorry no pictures of this because I opened it in an unboxing video and didn't think to take pictures of it. The box was very flimsy, almost looked as if it was damaged. The plastic window showcasing the phone had been pushed in creating a hole which you could stick your fingers into. That didn't really bother me much as long as the contents weren't damaged.
There were a few items in the box:
-The case
-Little card explaining the features of the case
-Screen protector and screen protector accessories (I didnt use any of these because I have a Spigen screen protector on my Nexus 5 already)
The case was held in place inside the box by a thin piece of cardboard with a weird paper strap which had adhesive on the very and which was stuck to the phone case. Peeling off the piece of paper with adhesive on it left a mark which I first thought was just stuck adhesive (Turns out this actually damaged the leather leaving marks)
The Case
The case felt very nice to the touch as it is real leather, It made my phone look like a little book. This case obviously adds a lot of bulk but its meant to replace your wallet in addition to protecting your phone.
Front of the case
Back of the case, notice the damage to the leather? Cutouts are fine with the exception of a little piece of plastic left over from the molding process with by the camera hole at 11 o'clock.
Great stitching and some branding.
Branding on the rib.
Inside the case, four pockets, some subtle branding.
How the phone is held in, some branding, Ringke Fusion case with a leather cover. All holes are nicely cut out and all buttons are covered and responsive.
The Conclusion
In conclusion it's a flawed beauty, it is so close to being perfect for me. I think this is a great start for Rearth, they usually make much cheaper products, but for the cost I don't think the adhesive should've left a mark like that (I feel its not acceptable), I think they should at least remove the "Ringke Fusion" on the case and it's missing one key feature that turns me off, there is no wake function for this case.
I will be contacting Rearth to see if I can get a replacement or if they will be updating this case at least with a sleep wake function.
Thanks for reading/watching guys!
Hello everyone
I had an idea about using my phone under water to take pics and videos etc. I'm a little paranoid about the flaps coming open though.
I was wondering if anyone had come across a case that covers all of the flaps but still gives access to the shutter button?
Also if not, have you guys got any ideas as to ways of guaranteeing that they stay closed?
I know it's a bit of an odd request! Lol
Thanks in advance for any help!
Will
I had sourced this out in Fall last year, and every single case I could find had the cutouts for ports open.
The only solution I had found was a company that 3D prints their cases, and I asked them if they could make me one without the holes cut out. They said yes, but the case was $50 plus $20 shipped, and would be ready in 3 months (due to backlog of their 3D printer).
I never went through with the order, but it can be done. Here's why:
Mentioned by the above company, this will cause additional wear and tear on your device, because while your goal is trying to keep the water out, waters' goal is to try to get in, and if successful, even with the flaps closed, that case is going to hold it there. Moisture will now be locked in against the case and phone, and can cause issues such as paint protection, fogging and possibly water damage.
My advice:
You're best just grabbing some medical tape from a medical supply store, and using that to keep the flaps closed. Medical tape is waterproof, similar to a band aid, but has only a slight adhesive to it, so it comes off easily without damage to your screen protector or phone itself. It's perforated so it's super easy to tear by hand too.
http://www.amazon.ca/Complete-Medic...8&qid=1423238156&sr=8-5&keywords=medical+tape
NOTE: Do NOT buy cotton tape, or lower quality "medical tape", as most are designed for plaster casting and have a very strong adhesive to them. They WILL damage your phone and possibly tear off your protector, damaging it. Look in low quality first aid kits at whatever "big box store" you want (WalMart, etc.). The cotton tape is white, and requires the use of scissors or a knife to cut. That is the **** stuff. If you can't easily tear it off in a straight edge by hand, it's not the correct stuff.
I recently recieved my second SPECK CandyShell Clear for my HTC 10 (I broke the first one by trying to mod it but that's a different story), so I took the chance to take some photos and give you a short review. Disclaimer: This review is neither sponsored, nor did I recieve any discount in order to write this review.
Pricing
I paid ~30 USDs at an online Android accessories retailer (used some available-to-all coupon that reduced the price by ~5 USDs).
The price is pretty hefty when compared to other HTC 10 cases except the original ice view ones.
Retail box
This case comes in the standard SPECK retail box, which looks nice IMHO and is very easy to open.
Build quality / Durability / Looks
Although it is made of plastic, this case definitely screams premium. The way it shimmers and feels in hand sets it apart from its competition.
Unlike the (now retired) Gem Shell I had for my One M9 and similar to the original CandyShells, this one has a two-layered construction: The outer layer is sturdy plastic while the inner one is soft rubber. Both layers are completely transparent (although the rubber has a very slight frozen look only notably when the case is not yet put on the phone).
SPECK promises that this case would resist UV yellowing and I can mostly confirm this: My first CandyShell Clear did not yellow for two month except the buttons. The buttons did yellow indeed but this did not affect the overall looks too much since the rest of the case stayed perfectly clear.
I had some CandyShell/GemShell/CandyShell Grip cases before and one of the very few downsides is that they were quite prone to scratches and looked worn after a couple of days. I was really astonished to see that SPECK made some serious improvements here: The first case had very few scratches after two month, none of 'em were obvious. No comparison to the elder cases where the gloss disappeared quickly due to the surface being covered by scratches all-over.
One nice detail is the SPECK logo. It is placed quite nicely to complement the HTC logo and not to interfere with it. But what it really makes it a stunner is how it is done. It is embossed in the rubber layer of the case in such way. that it appears to be embossed in the metal body of the phone. Nice idea, SPECK!
The only downside in this department is that this case adds some bulk. Not too much and nothing like UAG-like cases, but those who like their device as slim as possible might find it too bulky.
Protection
Protection is where this case really shines. The sturdy outer shell combined with the cushioning inner rubber layer keeps you covered in most drop situations. The front-side lip does not only protect the screen when putting it face to the table but is also thick enough to protect the screen while dropping on almost flat surfaces.
Fitting / Cutouts
This case sits like a glove. It is manufactured to fit the contours of the 10 like a perfect ten (pun intended). All cutouts are surrounded by rubber that will keep dust out of the case.
The small cutouts for the bottom-side and back-side microphone fit perfectly. The headphone jack cutout is big enough so that most headphones should fit into it. The camera cutout is quite big but this way, the flash should not interfere with the case (although I have not tested this). The bottom speaker cutout fits also well, same goes for the USB port cutout.
But the USB port cutout may be the biggest downside of this case: It is so tight that some cables won't fit. The original HTC charger cable, which comes with the 10 does. But my 3rd party cables with metal plugs did not fit and so won't any cables whose plugs are significantly bulkier than the rather slim plug of the original cable.
Remember that I told you, it was a different story that this is already my second CandyShell Clear? I broke the first one while extending the USB port cutout with a drill. Unfortunately, I did not spend enough attention and damaged the inner rubber layer which looked pretty ugly. So I replaced the damaged case with this new one and also replaced my cables with ones that provide slicker plugs. Quite some hassle but this case is definetly worth it.
In case you wonder which cables I was talking about: Aukey CB-CMD5 (pack of 5) will fit while Aukey CB-CMD2 (pack of 5) won't.
Liked this review? Do not forget to push the "thx" button!
Does the tpu on the front fit properly? The lip would get pushed in and down when I put the phone one and I couldn't get it to actually be a lip on the screen. I sent mine back. On the bright side speck has a very easy return process.
if you take a picture with the flash on, does the light bleed through the case?
aer0zer0 said:
if you take a picture with the flash on, does the light bleed through the case?
Click to expand...
Click to collapse
At least the flashlight does. Have not yet checked whether this affects photos. I'd assume so but I remember having read otherwise somewhere. As soon as I tested it, I will let you know.
TotallyAnxious said:
Does the tpu on the front fit properly? The lip would get pushed in and down when I put the phone one and I couldn't get it to actually be a lip on the screen. I sent mine back. On the bright side speck has a very easy return process.
Click to expand...
Click to collapse
This case is a tight fit indeed. It took me some patience to get the phone in while keeping the lid in place. Once the phone is in, it takes some force to remove it. Great for being sure that the phone won't slide out accidentally on drops. Not so great if you want to remove your phone frequently.