(Avis aux intéressés, j'ai traduit mon message en français, et reparti une discussion sur Frandroid.)
Hello,
I managed to map the partitions on the Gio 5660M (Bell Canada, 2.3.4, MUGK3) in order to extract an ODIN flashable complete stock backup.
I have also made a stock, rooted ROM backup by working in a hex editor. Other tools that helped the mapping were Winmerge, to do file comparisons with an Euro 5660 ROM, and Notepad++ for string searches.
Those with a 5660M that are experiencing issues after flashing Euro 5660 ROMs that have been posted here now have the possibility of flashing back their original radio and kernel.
ROM development and deployment is going to be safer going forward.
I copied the blocks with the dd command as follows:
dd if=/dev/block/bml1 of=/sdcard/bml1 bs=4096
WARNING!!! DO NOT dd /dev/block/stl5 as there have been multiple reports of bricking following reading it. We already know that this block contains the EFS partition, including the SIM-lock code. You can however dd bml5 without issue from a "live" phone. If you absolutely want stl5, you may get it by using a rooted custom recovery.
From what I've gathered bml is essentially a lower level interface to the same blocks accessed by stl, but the results differ somewhat in resulting file size.
Here are the results:
Code:
/dev/block/bml1 MIBIB
/dev/block/bml2 QCSBL
/dev/block/bml3 OEMSBL
/dev/block/bml4 AMSS
/dev/block/bml6 Essentially empty, with a FSR_STL string at the beginning.
/dev/block/bml7 arm11boot
/dev/block/bml8 boot.img. My initial assumption was based on the .ops file supplied with the Euro ROM I've done my comparisons with. This has since been confirmed with actual flashing.
/dev/block/bml9 recovery.img for the same reasons as above.
/dev/block/bml10 Essentially empty. Mine has a BMC string at the beginning which matches the CSC code on this phone, followed by an ON and an OFF.
/dev/block/bml11 Empty. \xFF all around.
/dev/block/bml12 Seems to contain the same RFS data as stl12, but with an additional 8 megs of data/padding, not readable by MagicISO.
/dev/block/bml13 Like 12 above, but user data
/dev/block/bml14 As above, but the almost empty partition
/dev/block/stl1 cannot open for read
/dev/block/stl2 cannot open for read
/dev/block/stl3 cannot open for read
/dev/block/stl4 cannot open for read
/dev/block/stl6 Empty: contains only \xFF
/dev/block/stl7 cannot open for read
/dev/block/stl8 cannot open for read
/dev/block/stl9 cannot open for read
/dev/block/stl10 cannot open for read
/dev/block/stl11 cannot open for read
/dev/block/stl12 system.rfs - is flashable as-is once tarballed. Also contains the CSC files as we're taking this from a "live" installation, contrary to an OEM provided image. (My image is also rooted for the same reason.)
/dev/block/stl13 data.rfs - User data partition
/dev/block/stl14 cache.rfs - Odin hangs when I try to flash it. Use CWM and dd back into place from the SD card.
From what I see we can't repartition our phones like the GT-I9000 guys do, so there are no PIT files to worry about. Only the OPS files which ODIN uses. We're not able to flash with Heimdall in its current configuration as it requires a PIT file.
GT-S5660M_MUGKG3_stock_rooted_ROM_v2.7z (101.46 MB)
Un7-Zip, flash tarball with Odin using the "One Package" option. Tested working on my phone. I think it goes without saying that flashing this is at your own risk.
(PDA: S5660MUGKG3 PHONE: S5660MUGKG3 CSC: S5660MBMCKG3)
Tutorial on flashing with Odin, with link for the appropriate version for our phone.
I've released my custom 5660M ROM, ArpegGioMod.
Goodbye,
Darkshado
Wow,
Thank you very much. The screen brightness issues and problems connecting to the mobile 3G network were very troublesome.
I will be flashing this ROM back to my s5660m.
THANK YOU!
STATUS UPDATE:
I have successfully flashed the image to my phone, i had to rename factory.rfs to system.rfs in order for ODIN to flash successfully. Also, it may not be important but I noticed that your image is missing the csc.rfs file.
I copied it from another ROM but it still didn't take it.
Even with the CSC.RFS file missing, it SEEMS to work GREAT! No more screen issues or 3G problems so far, I will keep you updated!
Again, thank you for uploading this, Hopefully soon there will be a CM7 for the s5660m!
Cool! Please, pretty please let me know as soon as possible how it turns out. When do you plan on trying this? This afternoon or later tonight?
Depending on how much you feel at ease with experimenting, you might be able to make a modified OPS file and new tar archive to flash only AMSS and boot.img to your system. Boot in recovery to wipe cache and dalvik-cache, then reboot the phone in normal mode. *If* things go according to plan you'd be left with a custom ROM'ed and functional phone. Otherwise just flash the whole thing back to stock.
Good luck,
Darkshado
Coolty said:
STATUS UPDATE:
I have successfully flashed the image to my phone, i had to rename factory.rfs to system.rfs in order for ODIN to flash successfully. Also, it may not be important but I noticed that your image is missing the csc.rfs file.
I copied it from another ROM but it still didn't take it.
Even with the CSC.RFS file missing, it SEEMS to work GREAT! No more screen issues or 3G problems so far, I will keep you updated!
Again, thank you for uploading this, Hopefully soon there will be a CM7 for the s5660m!
Click to expand...
Click to collapse
Great! You just made my day!
About the missing CSC file: CSC is an acronym for Carrier/Country Specific Code. The csc.rfs file is a partition image file that, as far as I can tell, is merged with the contents of the system.rfs partition. In our case, the CSC file would contain the APN settings, as well as the Bell proprietary apps like self-serve and remote PVR.
Instead, since I took the system partition from a live phone, the CSC content is already in the system.rfs partition. I think the idea behind this is that Samsung can release new CSC packages without having to update the whole firmware when "new" carriers add the phone to their lineup.
I'll see if I can edit the RFS partitions, (maybe by mounting them on the phone directly?) if so, I would be able to unroot, and make that separate CSC partition as well. That would make the backup completely stock, as if it came right from Samsung.
Another, simpler solution would be to modify the OPS file to skip the CSC partition.
One question: did you re-tar each file individually for ODIN to take them?
CM7 port: I'd love to have one on that phone as well, but I'm not in a position to tackle that project, yet. The good news is that since we now have a way to bring the phone back to stock, we can experiment safely.
Goodbye,
Darkshado
Depending on how much you feel at ease with experimenting, you might be able to make a modified OPS file and new tar archive to flash only AMSS and boot.img to your system. Boot in recovery to wipe cache and dalvik-cache, then reboot the phone in normal mode. *If* things go according to plan you'd be left with a custom ROM'ed and functional phone. Otherwise just flash the whole thing back to stock.
Click to expand...
Click to collapse
I will try this as well, will let you know the status of that as soon as I get to that. I am pretty confident with flashing phones by now
One question: did you re-tar each file individually for ODIN to take them?
Click to expand...
Click to collapse
No, I use linux so it was an easy process of copying the factory.rfs to my HDD, renaming it to system.rfs, deleting factory.rfs from TAR, and then adding system.rfs to the TAR file.
Let me know if you want me to try anything else, as I have access to linux and am pretty knowledgeable when it comes to things of that nature.
I can confirm that replacing amss and boot.img for 5660m from custom firmware meant for the 5660 works perfectly. I am using this tar: GioPro-1_2-LITE-by_ZimniY-S5660XXKQ6_S5660XXKQ5_S5660SEBKQ1.tar AND the GioPro 1.3 update zip. No screen issues or 3G problems. If you like I can upload the edited ROM for ODIN.
Step by Step guide for Noobs?
Hello,
My Samsung Gio S5660M is on an infinite loop.
Will this method fix the issue?
Can someone kindly give a step-by-step guide to this method (starting from what software/driver needed)?
Thanks a lot.
red02 said:
Hello,
My Samsung Gio S5660M is on an infinite loop.
Will this method fix the issue?
Can someone kindly give a step-by-step guide to this method (starting from what software/driver needed)?
Thanks a lot.
Click to expand...
Click to collapse
Why is your phone stuck in an infinite loop? What did you do to cause this?
did you somehow overwrote stl5(the efs partition afaik) while trying to unlock your phone?
Coolty said:
I can confirm that replacing amss and boot.img for 5660m from custom firmware meant for the 5660 works perfectly. I am using this tar: GioPro-1_2-LITE-by_ZimniY-S5660XXKQ6_S5660XXKQ5_S5660SEBKQ1.tar AND the GioPro 1.3 update zip. No screen issues or 3G problems. If you like I can upload the edited ROM for ODIN.
Click to expand...
Click to collapse
if you could post it, that would be much appreciated!!
steez003 said:
if you could post it, that would be much appreciated!!
Click to expand...
Click to collapse
I am currently in the process of uploading the edited TAR file to megaupload. The file is rather large so it may take another hour or so to complete. I will update this post when it is completed.
EDIT:
Here you go! GioPro 1.2 LITE edited for use with the Samsung Galaxy s5660m
Gio Pro 1.2 LITE updated for canadian s5660m by coolty
Coolty said:
Why is your phone stuck in an infinite loop? What did you do to cause this?
did you somehow overwrote stl5(the efs partition afaik) while trying to unlock your phone?
Click to expand...
Click to collapse
Hello Coolty,
Yes, that's exactly what happened. I tried to unlock it using Andorid Terminal Emulator, and although it gave me the unlock code, it fell into infinite loop upon restart.
Will your uploaded file fix this problem?
What would possibly provide a detailed guide on how to use the file?
Thanks.
red02 said:
Hello Coolty,
Yes, that's exactly what happened. I tried to unlock it using Andorid Terminal Emulator, and although it gave me the unlock code, it fell into infinite loop upon restart.
Will your uploaded file fix this problem?
What would possibly provide a detailed guide on how to use the file?
Thanks.
Click to expand...
Click to collapse
Hi,
I'm not one for explaining things in great detail, but the basic breakdown of the things you need (google is your friend) are:
1) Odin_Multi_Downloader_v4.42
2) The USB drivers for your phone (Hint: Samsung Kies)
3) OPS File (for this phone, I recommend GIO_v1.0.OPS)
4) Either a single TAR file or multiple files (eg, appboot, PDA, etc) For the file I am uploading it will be a single TAR file which is a package that includes all the things needed.
Then, you just remove the battery in your phone, unplug it from USB or wall charger, put battery back in, hold vol down + HOME + power until you see a screen (you may have to press a vol key after that, read the screen to see if you need to) Your screen on the phone should say DOWNLOADING... This is when you:
1) connect phone to computer via USB after installing drivers (kies, usb driver)
2) make sure kies is closed
3) run ODIN
4) choose the proper OPS file
5) click single package
6) choose the TAR file you want to flash to your phone
That's it!
EDIT:
I am providing some forum links that may better explain how to do what you need done:
How to unbrick (for samsung ACE, but applies to the 5660m) http://forum.xda-developers.com/showthread.php?t=1071970
How to use ODIN to flash your phone: http://forum.xda-developers.com/showpost.php?p=16979859&postcount=549
And of course, the great bible of GIO 5660 links and information: http://forum.xda-developers.com/showthread.php?t=1209425
I have updated my previous post to include the download link to the fixed rom for use with the s5660m.
(search for "s5660m by coolty" on the forums to find it)
Coolty said:
I am currently in the process of uploading the edited TAR file to megaupload. The file is rather large so it may take another hour or so to complete. I will update this post when it is completed.
EDIT:
Here you go! GioPro 1.2 LITE edited for use with the Samsung Galaxy s5660m
Gio Pro 1.2 LITE updated for canadian s5660m by coolty
Click to expand...
Click to collapse
Thanks! I ended up flashing my phone and I have run into a problem. For some reason Wifi won't work in GioPro. It says 'Turning on...' and then it will say 'Error'. Any ideas?
Thanks
Will this help at at all with a blank IMEI? I assume this would only help for people flashing back to stock firmware or recovering from a non-bootable or reboot loop phone?
steez003 said:
Thanks! I ended up flashing my phone and I have run into a problem. For some reason Wifi won't work in GioPro. It says 'Turning on...' and then it will say 'Error'. Any ideas?
Thanks
Click to expand...
Click to collapse
I'm also running into the same issue
Sent from my Nexus S using XDA App
Thats why i recommend you guys always do a factory reset before and after flashing , these glitches , like gps issue , wifi , stuck on boot logo , won't happen if you properly fectory reset before and after flashing....
Waqasshazad: Maybe wiping the caches will help, but the issues might be due to running a 5660 on a 5660M as well. We know the kernels and modems aren't compatible, it may go a bit further. By the way, it's spelled factory.
MacrossFX: I've seen mentions of people dd'ing their stl5 partition into a file and then back on the phone, but I'm unsure this worked in the end. I'm afraid your only solution might involve a shipment to the service center...
ClockworkMod Recovery for the Samsung Galaxy Gio GT-S5660
http://forum.xda-developers.com/showpost.php?p=16980117&postcount=559
May be this can backup for you , too with s5660m , i have tested on Gt s5660 and it worked perfectly fine..
waqasshahzad1986 said:
Thats why i recommend you guys always do a factory reset before and after flashing , these glitches , like gps issue , wifi , stuck on boot logo , won't happen if you properly fectory reset before and after flashing....
Click to expand...
Click to collapse
I followed your instructional video and did do a factory reset before and after. Maybe i'll try reflashing it again tonight and see what happens.
Related
Reference http://www.samfirmware.com/WEBPROTECT-p1000.htm
Saw under the Asia Firmware 'P1000DXJM4 ## ODIN 1.7 | P1.PIT | Version 2.2 | 2010 December' is available and to be cautious, i seek seniors' opinion before i go ahead and flash mine ^^
Any recommendation on how to proceed is appreciated, esp with ODIN (dont know what it is even read so much about this word)!
I already backup with TB
edit: Connect to Kies and says 'This device's version cannot be updated.' Stating PDA: JK2 / Phone: JJ2 / CSC: JJ2. now even more confused
edit update after flashed JME instead of JM4 (long story short):
"i will write down the event by event of recovery as reference:
1. flash the JVJL1 (no problem on reboot) by mistake then flash JM4 (missing dbdata.rfs) tar file downloaded from samfirmware.com and failed to reboot due to the missing file.
2. did some silly step and resulted in (phone .. ! .. pc) icon
3. run odin 1.7 and plug the usb and odin show is connected with tab
4. flash JM4 (yes with missing dbdata.rfs) and able to bring the tab back to download mode but unable to reboot into tab
5. flash Roto's dbdata.rfs file (http://forum.xda-developers.com/show...91&postcount=1) and able to reboot right after but missing pda & csc info (*#1234#)
6. tried the hard reset (http://forum.xda-developers.com/show...&postcount=106) but no help
7. download Roto's pre-rooted JME 3 files as mentioned (http://forum.xda-developers.com/showthread.php?t=895827) and finally boot the tab with full *#1234# details.
* So if you see the (phone .. ! .. pc) icon dont panic. like KChauJen said, able to solve with enough reading. i listed my route to recovery as reference to give you positive hope to retry.
TB's backup in Internal SD and before flashing JME, i copied the TB folder to my hdd during the missing pda & csc boot and did a backup on JME reboot, copy paste back to TB folder under internal sd and the restore work flawlessly."
cant be updated? er, i was from jk2 to jm4. did you applied oclf? if you did, try undo it b4 anything.
Hi fastcx, thanks for replying and sharing your experience. I did some further reading in some singapore forum saying have to run the kies patch (http://forum.xda-developers.com/showthread.php?t=835628) and spoof firmware version in order to update. i have yet to try due to somewhere in the same forum also said that once updated:
1. cant go back version
2. z4root wont work (which i am already using)
may i know have you rooted your SGT? need more solid info before taking the route to update the firmware as already using SGT as my primary device. I havent OCLF yet
rooted, since day 1, after every update (jj1>jj2>jk2) able to root with z4root till jm4 which requires SOC(SuperOneClick). To use kies, switch back to samsung default launcher b4 u connect using kies. I do not have any issue there. Another note is that after root, i always go back to /system/app to check n remove any apps that I do not need using adb shell.
The interface changed, to darker color, dlna client really working now, oclf performance improvement might not be obvious this time around. I suspect they really optimized it, everything is more stable now. Over protective I would say, cause any previous flashlight apps isnt going to sustain the led light for over 2sec. Default browser is a wee bit smoother now.
SuperOneClick is very easy to use anyway, so give it a try, oclf is useful only when u have over 400mb apps + loads of sms & contacts..anything related to I/O will have improvement.
The worse case scenario is just if kies still do not allow u to update, just use odin..what did you do previously? How do you update previously?
VNPython said:
Reference http://www.samfirmware.com/WEBPROTECT-p1000.htm
Saw under the Asia Firmware 'P1000DXJM4 ## ODIN 1.7 | P1.PIT | Version 2.2 | 2010 December' is available and to be cautious, i seek seniors' opinion before i go ahead and flash mine ^^
Any recommendation on how to proceed is appreciated, esp with ODIN (dont know what it is even read so much about this word)!
I already backup with TB
edit: Connect to Kies and says 'This device's version cannot be updated.' Stating PDA: JK2 / Phone: JJ2 / CSC: JJ2. now even more confused
Click to expand...
Click to collapse
Yeah... I'm in your case.
Thinking does it would be updated or not???
1. cant go back version
2. z4root wont work (which i am already using)
Click to expand...
Click to collapse
Just look at inside of tar file, and according to the Chainfire's Warning, the three files:
* boot.bin
* Sbl.bin
* zImage > 7,000K
So, this firmware would be has the protected boot loader. It would give us a lot of trouble in the future of updating and downgrading.
I think, this firmware can be updated with the help from Roto, eliminate the three files above and just take the PDA part.
I was using CSC: XEV (Vietnam) then to SIN (Singtel) and feel good and when Nov'10 update came, updated via Kies wihtout any trouble. When Dec'10 update came, tried with SIN resulted unable to update, switch back to XEV also resulted unable to update. I havent try XSO which the singapore forum stated successful for those with that CSC.
So i have to try to switch to XSO and report in later. be it protected boot loader or not, as long as we want stable and more 'juice' to service our daily SGT needs, no choice but to follow. I do believe as days goes, seniors like Roto alike will crack the nut for us to appreciate further.
on other note, my default email (not gmail) app seem got problem whenever you click reply or forward any email will result in force close. do not know if this bug related to after i switch from SIN to XEV (to try update) then switch back to SIN and follow up by restore using TB.
anyone has similar force close on the default email app?
backing up with TB now should we (those yet to update jm4) wait for Roto to do his magic for this update?
edit: tried with XSO and also unable to update... that really puzzle me.
edit 2: unroot with z4root and try still unable to update... now looking at ODIN route
perhaps odin route is the best solution for your case, but from jk2 > jm4 not sure if pit file is needed? repartitioning needs it tho, perhaps its good that u do back up of everything, let us know ur flashing result. Odin will definitely able to do the job
oh no... T_T somehow i downloaded P1000JVJL1 (Arabic) by mistake and Odin 1.7 with Auto Reboot & F. Reset Time, selecting the mistaken Arabic firmware (PDA) and flash it without any problem (JVJL1 / JXJK3 / JVJK4) and able to reboot itself.
After notice the wrong firmware, downloaded the right one (P1000DXJM4) from samfirmware.com and using Odin 1.7. Repeating the above steps but the phone briefly flash and came back the 'download mode' and nothing happened although Odin stated passed without any error.
I able to hold the power to shutoff and turn on again and the screen shows the samsung logo screen and stay flashing the word 'samsung' with 1 then 2 quick vibrate (like force close) and didnt boot into the main screen!
what should i do next?? is it bricked?? T_T
edit: the downloaded filename is 'P1000DXJM4_P1000DXJM2_P1000OLBJM1_HOME.tar' and anyone know if correct one?
edit 2: now i am downloading DXJK2 and see if i am able to revert the flash of JM4 T_T
edit 3: is over T_T saw the (phone .. ! .. pc icon)
This is due to dbdata.rfs missing. Please refer to the guide of flashing JMC/D/E series.
BTW, I have a problem is Camera Faulty error when start the camera app. Somebody mentioned that the LCD density can't set too small, but I have reverted it back to default 240, the problem still there. Any clue about it?
Sent from my GT-P1000 using XDA App
thanks dahuzi, i wonder if i choose to flash eu rom by Roto, would his rooted bring my tab back to operation? appreciate any help to bring back my tab.
i am able to bring my (phone .. ! .. pc icon) to the download mode. flashing anything before JM4 wont work anymore (fail at odin 1.7 and 1.3) and i am able to go back to hard reset option (holding vol up and power up). now i need to get the TB backup from the int SD before i try anything new. possible to retrieve in download mode?
edit: where to find the dbdata.rfs for this JM4? can anyother dbdata.rfs from other firmware able to fill it in? help ~ T_T
Hi VNPython,
Your case is complecated one, take it easy and read the thread from Chainfire "WARNING! Do not flash ... ", in there, a lot people has solved with different path.
Be patient, Bro. At that moment, your TAB is not Brick yet, but be careful because it's on the way of the End.
Wish you luck.
Take care.
ha.. i hope to win this war ^^ and learning the way of android!!
edit: just a quick question - does TB backup all user and app data in internal SD or External SD? i got bunch of files in my ext SD folder '.android_secure' and inside have files like 'com.keramidas.TitaniumBackup-1.asec' can any senior confirm is a valid TB backup files and can be used to restore my user & app data? many thanks!
TB (TitaniumBackup) file in the internal SD (in my case is the default), please double check.
Please give us your detail of winning as I'm scare of Samsung flash. My history is, 4 years ago, I bricked my Omnia phone Samsung after I flashed the rom from SIN to AUS. And, this's my second device on Samsung but this is Android and I want to learn the new OS.
Take care, Bro.
hey guess what? i managed to get a file for dbdata.rfs from Roto and got the tab back live but missing PDA and CSC field (checking with *#1234#). tried the reset to get the pda and csc back but failed.
learned quite a few things along the way and will update this thread after completing my mission to update my tab to JM4.
windows seem cant extract and tar file for android tar files. i tried to extract jm4 files and add dbdata.rfs into it but when flashing, it fail.
worst come to worst, flash the JVJL1 to get the working tab again
i hope Mr. Roto could let me know what software to install on windows that able to 'untar' and 'tar' properly with android (linux) files. tried 7z and winrar both cant untar without error.
try using winrar to do the add on of dbdata.rfs, anyway, good luck next time, double check what you downloading
fastcx said:
try using winrar to do the add on of dbdata.rfs, anyway, good luck next time, double check what you downloading
Click to expand...
Click to collapse
Wow... another Maitre!!! What's your winrar???
Look and read:
.....i hope Mr. Roto could let me know what software to install on windows that able to 'untar' and 'tar' properly with android (linux) files. tried 7z and winrar both cant untar without error.
Click to expand...
Click to collapse
Thanks
sorry for the late update as yesterday too late to post anything after able to get my tab back to life! the learning curve is nice and not stressing since many time i see the icon of (phone .. ! .. pc) yet i am able to bring the download (digging) icon back again always.
i will write down the event by event of recovery as reference:
1. flash the JVJL1 (no problem on reboot) by mistake then flash JM4 (missing dbdata.rfs) tar file downloaded from samfirmware.com and failed to reboot due to the missing file.
2. did some silly step and resulted in (phone .. ! .. pc) icon
3. run odin 1.7 and plug the usb and odin show is connected with tab
4. flash JM4 (yes with missing dbdata.rfs) and able to bring the tab back to download mode but unable to reboot into tab
5. flash Roto's dbdata.rfs file (http://forum.xda-developers.com/showpost.php?p=9305891&postcount=1) and able to reboot right after but missing pda & csc info (*#1234#)
6. tried the hard reset (http://forum.xda-developers.com/showpost.php?p=9482192&postcount=106) but no help
7. download Roto's pre-rooted JME 3 files as mentioned (http://forum.xda-developers.com/showthread.php?t=895827) and finally boot the tab with full *#1234# details.
* So if you see the (phone .. ! .. pc) icon dont panic. like KChauJen said, able to solve with enough reading. i listed my route to recovery as reference to give you positive hope to retry.
TB's backup in Internal SD and before flashing JME, i copied the TB folder to my hdd during the missing pda & csc boot and did a backup on JME reboot, copy paste back to TB folder under internal sd and the restore work flawlessly.
after 1 days usage, the trouble found is email app still being force close whenever you reply or forward any email. any senior have similar force close on original email app?
KChauJen said:
Wow... another Maitre!!! What's your winrar???
Look and read:
Thanks
Click to expand...
Click to collapse
My bad. How polite of you.
Back to topic, VNPython everything there is a first time it's good info here. Perhaps you can edit your 1st post with info from your last post?
EDIT: 1 thing though, do you have any issue regarding using samsung apps?
samsung app can use, checked my CSC and its KOR. Apps: Vlingo words to action, Vietnamese Dictionary application & blinkx Beat. didnt try any of them. just *#272*IMEI# and there's no SIN or XEV or XSO or Asian Sales Code in the Roto JME (EU) multiCSC. maybe will try to download multicsc with asian sale code.
* on the email app force close, i delete the email account and re-setup them, and the force close is gone. could be due to TB's restore? anyway, is solved ^^
I wonder will i be able to flash DXJM4 if there is a full tar file?
VNPython said:
....
I wonder will i be able to flash DXJM4 if there is a full tar file?
Click to expand...
Click to collapse
Please consider it carefully, Bro.
What I looked inside of the tar file, and according to Chainfire's Warning, it has the protected boot.
If we can eleminate the three files:
* Boot.bin
* Spl.bin
* zImage
and put back to the tar file with the encrypted code by Samsung (maybe we can ask Roto) then we can flash this modified firmware JM4.
FYI.
I'm very happy to announce, that a developer raidzero from rootzwiki forum, has made us a fully working recovery for Samsung Galaxy w i8150!
You can download it from here:
DOWNLOAD
TEMPORARY LINK .... USE THIS IF FIRST ONE DOESN'T WORK
THANKS TO andynroid FOR PROVIDING LINKS!
Flashing recovery is very simple, all you need is root access on your phone, and adb on computer. You just copy downloaded recovery on internal sdcard. Then disconect phone from copmuter. Make sure that USB debugging is on. Now connect it again but don't connect phone memory (computer shouldn't see sdcard and internal memory in Windows explorer), open command prompt and got directory where adb is installed, now enter this:
Code:
adb shell
$su
#dd if=/sdcard/RZR-2.1.4-ancora-rec.img of=/dev/block/mmcblk0p13
This is all. Now turn off phone and turnd it on like this: hold Volume Up + Home + Power button, when Samsung sign appears relese power button but still hold other two, until recovery is loaded. Bamm you are in, and ready to flash something, or backup ! Expolre the recovery, it has a lot of options, you can even choose what color of menus you want .
I would like to thanks raidzero again for all his effort he made! And also big thanks to arco68,for much need informations he provided!
We can now expect, that when developing his recovery and adding new goodies, this recovery will follow others!
great news!! Thanks for your effort!
Has anyone had a chance to test the Recovery?
Will this work on the Samsung Exhibit II?
thanks mate.downloading now. just in case it needs to be recovered. after this we would see custom roms developed by our developers here..
klingel_One said:
great news!! Thanks for your effort!
Has anyone had a chance to test the Recovery?
Click to expand...
Click to collapse
I've tested it and it works
radgoos said:
Will this work on the Samsung Exhibit II?
Click to expand...
Click to collapse
I wouldn't bet that this will work on Exibith II cause every phone has different partitions.
after giving me the command you said to me reacts to: permission denied.. Whi?
lipanz said:
thanks mate.downloading now. just in case it needs to be recovered. after this we would see custom roms developed by our developers here..
Click to expand...
Click to collapse
Definitely...BTW can anyone adv us the rooting method Odin or....
can you show me a screen when you give the command adb?
when I try to restart the device in recovery restarts continuously and never give me the recovery menu
qzem said:
I'm very happy to announce, that a developer raidzero from rootzwiki forum, has made us a fully working recovery for Samsung Galaxy w i8150!
You can download it from here:
www.rzdroid.com/ftp/recovery/gingerbread/2.1.4/RZR-2.1.4-ancora-rec.img
Flashing recovery is very simple, all you need is root access on your phone, and adb on computer. You just copy downloaded recovery on internal sdcard. Then disconect phone from copmuter. Make sure that USB debugging is on. Now connect it again but don't connect phone memory (computer shouldn't see sdcard and internal memory in Windows explorer), open command prompt and got directory where adb is installed, now enter this:
Code:
adb shell
$su
#dd if=/sdcard/RZR-2.1.4-ancora-rec.img of=/dev/block/mmcblk0p13
This is all. Now turn off phone and turnd it on like this: hold Volume Up + Home + Power button, when Samsung sign appears relese power button but still hold other two, until recovery is loaded. Bamm you are in, and ready to flash something, or backup ! Expolre the recovery, it has a lot of options, you can even choose what color of menus you want .
I would like to thanks raidzero again for all his effort he made! And also big thanks to arco68,for much need informations he provided!
We can now expect, that when developing his recovery and adding new goodies, this recovery will follow others!
Click to expand...
Click to collapse
Thanks again, will try this ASAP, just a few questions:
Is /dev/block/mmcblk0p13 the Recovery partition??
Is it been overwritten by the dd if.......of??
Should the original stock recovery?? be backed-up/saved first??
Is there an MD5 or anything to check file integrity:
This could be used on the Device: Android File Verifier
Can the procedure be done using Terminal Emulator on the phone?
Do I need to have stock ROM for it to work?
snake873 said:
after giving me the command you said to me reacts to: permission denied.. Whi?
Click to expand...
Click to collapse
There are two possible reasons for this either you didn't run su command first, or you don't have rooted phone.
irishpancake said:
Thanks again, will try this ASAP, just a few questions:
Is /dev/block/mmcblk0p13 the Recovery partition??
Is it been overwritten by the dd if.......of??
Should the original stock recovery?? be backed-up/saved first??
Is there an MD5 or anything to check file integrity:
This could be used on the Device: Android File Verifier
Can the procedure be done using Terminal Emulator on the phone?
Click to expand...
Click to collapse
1. Yes /dev/block/mmcblk0p13 is recovery partition
2. It is gonna be overwritten with costum one.
3. You can back it up that you reverse dd command. Or I can upload original recovery.
4. There isn't MD5 cause noone made it , you only need MD5 file if you would like to flash this via Odin.
nakTT said:
Do I need to have stock ROM for it to work?
Click to expand...
Click to collapse
Do you know any custom rom for our phone ? But no it is not rom related.
snake873 said:
can you show me a screen when you give the command adb?
when I try to restart the device in recovery restarts continuously and never give me the recovery menu
Click to expand...
Click to collapse
What screen? From computer or phone? Your phone need to be turned on and booted in android when running dd command.
qzem said:
There are two possible reasons for this either you didn't run su command first, or you don't have rooted phone.
1. Yes /dev/block/mmcblk0p13 is recovery partition
2. It is gonna be overwritten with costum one.
3. You can back it up that you reverse dd command. Or I can upload original recovery.
4. There isn't MD5 cause noone made it , you only need MD5 file if you would like to flash this via Odin.
Do you know any custom rom for our phone ? But no it is not rom related.
What screen? From computer or phone? Your phone need to be turned on and booted in android when running dd command.
Click to expand...
Click to collapse
From computer
---------- Post added at 12:09 PM ---------- Previous post was at 11:41 AM ----------
ahahaha ok ok I did thank you very much for your patience
qzem......top marks for your persistence
qzem said:
There are two possible reasons for this either you didn't run su command first, or you don't have rooted phone.
1. Yes /dev/block/mmcblk0p13 is recovery partition
2. It is gonna be overwritten with costum one.
3. You can back it up that you reverse dd command. Or I can upload original recovery.
4. There isn't MD5 cause noone made it , you only need MD5 file if you would like to flash this via Odin.
Click to expand...
Click to collapse
Thanks, gotta learn ODIN first,
btw, thanks for the ODIN d/l........installed it, but still unsure how to proceed???
I have latest Kies installed on my laptop, any reason why you do not use it?? It appears to allow back-ups and restores, also new firmware d/l.
As I am new to Samsung, and also ODIN, but does using ODIN have advantages over Kies, and is it safer to upgrade new f/w with ODIN or Kies, do you lose root, or anything else??
BTW, on the MD5 thing, for the RZR-2.1.4-ancora-rec.img
I used MD5 Checksum Tool from http://www.novirusthanks.org/product/md5-checksum-tool/
to generate the MD5.
File: RZR-2.1.4-ancora-rec.img
Size: 5230592 bytes
Publisher: Unknown
Checksum (MD5): 3b9cc641aa898910b5bad911bd38f675
*File generated by MD5 Checksum Tool*
http://www.novirusthanks.org
Click to expand...
Click to collapse
I just think it is good security practice to check file integrity before applying on your device, as many things can happen, like data corruption, while transferring file from download on Laptop to SD card, and best to check file on device SD or Internal Storage with AFV against MD5 generated at source.........
which I did not check at source, but I am just illustrating for example!!
[BTW, lots of MD5's on rzdroid.com recovery ftp site, here, but not sure of our .img file
The above MD5 is what I got from the d/l file
Thanks again, I saw your stuff with raidzero on rootzwiki.........
top marks for your persistence, and a good result for all i8150 owners.
irishpancake said:
Thanks, gotta learn ODIN first,
btw, thanks for the ODIN d/l........installed it, but still unsure how to proceed???
I have latest Kies installed on my laptop, any reason why you do not use it?? It appears to allow back-ups and restores, also new firmware d/l.
As I am new to Samsung, and also ODIN, but does using ODIN have advantages over Kies, and is it safer to upgrade new f/w with ODIN or Kies, do you lose root, or anything else??
BTW, on the MD5 thing, for the RZR-2.1.4-ancora-rec.img
I used MD5 Checksum Tool from http://www.novirusthanks.org/product/md5-checksum-tool/
to generate the MD5.
I just think it is good security practice to check file integrity before applying on your device, as many things can happen, like data corruption, while transferring file from download on Laptop to SD card, and best to check file on device SD or Internal Storage with AFV against MD5 generated at source.........
which I did not check at source, but I am just illustrating for example!!
[BTW, lots of MD5's on rzdroid.com recovery ftp site, here, but not sure of our .img file
The above MD5 is what I got from the d/l file
Thanks again, I saw your stuff with raidzero on rootzwiki.........
top marks for your persistence, and a good result for all i8150 owners.
Click to expand...
Click to collapse
Well I really don't know that is better to use Kies or Odin. If you want official and (what is supposed to be tested) firmware, tha you better use Kies (but well even with kies your phone could get bricked, I've learned that from one user here ). If you want to flash latest firmware, which sometimes is not availible on all the countries, and you can't get it from Kies fast enaught, than I suggest odin is the choice. I prefere Odin, cause I don't like official stuff .
To use Odin is very simple. You need to turn on phone with Volume Down + Home + Power. When you are prompt (on hte phone),wether to conutioue od cancle, you connect phone and computer with USB cable, and choose contuinu, now you are in download mode. Then all you have to do, to choos proper .ops file (button OPS) in odin, an proper firmware (usually you choos that under One Package button, if you have one package in tar.md5), then you wait for chekcking md5. When is checked you just click Start, and wait for stuff to happen.
Don't forget that there is a possabiltiy that something might go wrong with flashing, but it is not that big one. I suggest, that you first made full nandorid backup with recovery, if something goes wrong, you can boot you phone in recovery and restore it totaly. And one more suggestin when flashing, do it with latop(if possible), so that you have battery and power cable plugged in laptop, if electricyty goes out, that you still have battery to run laptop.
And thanks for the support you guys are showing to me, since I'm not a developer. I try really hard, to get people that are willing to help us developing better roms for our phone !
qzem said:
There are two possible reasons for this either you
Do you know any custom rom for our phone ? But no it is not rom related.
Click to expand...
Click to collapse
Spot on. I just need to know if it is ROM related (that I need a ROM file on my PC).
Thanks for the reply.
Hey there, just a noob question:
Where are adb drivers installed? I'm working under Windows 7.
I tried to google this and ended up here /developer.android.com/sdk/index.html
and downloaded the first two files, but I'm unsure what to do now. Thanks in advance!
Hey qzem,
Am I right, that the adb driver should be installed, when i first installed Kies?
Is your Guide How-To Install the recovery also working on my mac? I think so, or am I wrong?
Perhaps you already figured by now, I'm new to Android!
There is one more thing i can't seem to figure out:
In foreseeable future, there are hopefully some nice custom roms for the Galaxy W. Do I have to install recovery everytime i flash a new Rom? Or is it like a bios, that has nothing to do with the actual Android System?
Thanks for your help in advance
fender90 said:
Hey there, just a noob question:
Where are adb drivers installed? I'm working under Windows 7.
I tried to google this and ended up here /developer.android.com/sdk/index.html
and downloaded the first two files, but I'm unsure what to do now. Thanks in advance!
Click to expand...
Click to collapse
For adb, you need to download Android SDK from here. Download zip file and extract it somwhere. Than go in folder where you have extract it and run SDK Manager, from there you will install adb rivers and everything else. When you are done (it could take a while, to download and install everything), open Command promnt and follow the instrucions I've wrote in first post.
klingel_One said:
Hey qzem,
Am I right, that the adb driver should be installed, when i first installed Kies?
Is your Guide How-To Install the recovery also working on my mac? I think so, or am I wrong?
Perhaps you already figured by now, I'm new to Android!
There is one more thing i can't seem to figure out:
In foreseeable future, there are hopefully some nice custom roms for the Galaxy W. Do I have to install recovery everytime i flash a new Rom? Or is it like a bios, that has nothing to do with the actual Android System?
Thanks for your help in advance
Click to expand...
Click to collapse
The same goes for mac users, there is also Android SDK for mac. You can install Kies before this, but you need both because kies includes drivers for this phone exactly. As far as recoverey goes, if it is not included in ROM, which you flash, I think you'll need to install it again. I hope that developers will include recovery in their roms.
Thanks so far qzem,
It seems like theres someone in your Cyanogenom-Forum-Post qzem, who is trying and willing to help making a custom rom. But he seeks for som guidance!
Perhaps someone with experience like, arco can take him under his wings!
Hi there,
i would like to thank you. Everything works like a charm.
Did the flash, tried the recovery.. and uaaaahhhh....
...i forgot to backup the original recovery!
can someone please, please upload it to somewhere??
thx.
Zetup-EXe
Hello all and a good day.
Device: Samsung Galaxy Note 8.0 GT-N5100 (3G) - XME (Malaysia)
What I did: Nothing unusual! Device mainly used for text reading and some writing. After updated to Android 4.2.2 (PDA: N5100XXCMI1, CSC: N5100OLBCMH2, MODEM: N5100XXCMI1) via ODIN, the symptom # 1 appeared. The firmware for Malaysia was downloaded from the sammobile.com.
Same time I came to know the importance of /efs backup, so rooted (1st time) the device, backed-up /efs via EFS Pro, used Triangle Away, unroot, and flashed the stock. Since the symptom # 1 continued, I did a factory reset, and then all other symptoms appeared.
Symptoms:
1) Tablet doesn’t vibrate.
2) Kies is unable to detect the tablet.
3) SIM Cards are not detected. A prohibition sign is shown at the cell signal (left to the battery indicator) (see image 1).
4) In “Settings > About device”, and in “Settings > About device > Status”, many fields are stated as “Unknown”, e.g.:
Baseband and IMEI (see image 1 and image 2). Incorrect Serial number (/efs has the correct one as in the back cover).
5) Camera view is upside down.
6) Proximity sensor doesn’t work. In the *#0*# Test mode, Proximity value is 1.0. If exit and check again value becomes 0.0.
7) Regardless of Flight mode or not Cell standby drains the battery a lot. Once activated, Flight mode turns grey (see image 3).
8) [SOLVED, see 5th post] Several times (not always), a white screen appeared at the boot screen (model name), and also when plugged to power source while the tablet switched off. I guess something to do with param partition.
9) [SOLVED, see 5th post] "No command" error message in the stock recovery (3e).
9) “Modem boot timeout” and “Couldn't find 'rild' socket” errors in logcat -b radio.
10) When tried to use the tablet as a modem from Windows 7, it gives an Error 692, and the diagnostics states, “Timed out waiting for response from modem”.
Solutions tried (no success): As many, I too tried various /efs based solutions mentioned in XDA, and flashed all the five firmwares available for the device, but the problem stays same. I tried to solve this without troubling others much, but now I am lost.
Help needed: Is this problem can be fixed by me with some guidance, which would be great since to claim warranty the tablet need to be send to another country. Or is it a hardware problem, therefore I should send it straight to Samsung service without wasting more time?
Attached files, if they help:
1) Outputs of the following commands
logcat -b radio
logcat *:E
dmesg
ls -la /efs
ls -la
mount
cbd -t xmm626x -o t
2)
- recovery log from - CivZ_rev1.1-PhilZ 5.1.1 (touch)
- build.prop file
Thank you for reading. Greatly appreciate any help and guidance. Sorry, if I violate any XDA rules in this post. Kind regards!
New Problem: "There is no PIT partition."
Last night managed to fix a part of the problem (customer.xml error in logcat) in the above post thanks to the guidance from civato. In an attempt to fix other problems, last night I had mistakenly executed the following cmd in ADB while in recovery.
Code:
dd if=/data/media/0/efs.img of=/dev/block/[B]mmcblk0[/B]
The correct one should have used is mmcblk0p3 (/efs partition in Note 8.0). At least I managed to do some damage, otherwise all the credit goes to Samsung.
Now I can go to download mode only. A white screen flashes if try recovery mode or normal boot or even connect to a power source to recharge. Since charging or not also unsure (before this happened battery was 100%), I have a limited time to use the device to get it to work properly. Other problem is, if fail, can’t claim warranty as there’s no way to use the Triangle Away in this situation.
Now when try to flash via ODIN:
1) normal way - it failed stating, "There is no PIT partition." (see image 1).
2) with kona3g.pit I have - it failed stating, "Re-partition operation failed." (see image 2).
Even when the device was working properly, 2nd option never worked for me.
My kona3g.pit read well by PIT Magic 1.3.10.
Can anyone provide me a working .pit for Note 8 GT-N5100. Thinking of trying Heimdall Suite 1.4.0 tonight, but need some reading as I never used it and limited battery time for flashing.
Any advice to recover my device is highly welcome.
King regards.
Here you go, unzip it and in Odin select repartition and then Odin a new stock rom. (PDA)
Or look here for the 5110 pit file it should alos work on the 5100 as the modem partition is also created.
reinstall your csc also after rom onstallation
PS try the included Odin
Working kona3g.pit for GT-N5100
civato said:
Here you go, unzip it and in Odin select repartition and then Odin a new stock rom. (PDA)
Or look here for the 5110 pit file it should alos work on the 5100 as the modem partition is also created.
reinstall your csc also after rom onstallation
PS try the included Odin
Click to expand...
Click to collapse
Brilliant and thank you! The Odin3_v3.07.exe you provided missing an Odin3.ini (see image). I used an Odin3.ini (see attached files) that I have (for the same version) together with your Odin3_v3.07.exe and kona3g.pit, and the flashing went perfectly without any errors. So your kona3g.pit is a genuine working one. Thank you
I’ll continue further tonight and post here. My friend share his laptop with me, therefore I have limited time.
EDIT: When looked from the PIT Magic 1.3.10, the GT-N5110.pit is same as the GT-N5100 one (kona3g.pit). But when looked from the HxD - Hexeditor 1.7.7.0, the signatures at the end of the files are different, so it might not work on the sister device. Also, your GT-N5110.pit has trailing zeros after the signature, somewhere I read that these zeros must be deleted from a hexeditor for it to work.
Kind regards!
Image:
Solutions for symptoms 8 & 9
Solution for symptom 8:
Googled for a param.bin for Note 8.0, but only found one for Galaxy S3. Anyway, being fed up with the white screen, I copied S3 param.bin to the mmcblk0p4 partition of Note 8.0, surprise it worked. But the boot screen became S3 . Later among my backups, I found a param backup of mmcblk0p4 that I took via EFS Pro. Unfortunately couldn't restore it via EFS Pro as I had renamed the tar.gz to keep things tidy. So I extracted it to get a file called param. Since this param didn't work after copying, I compared it in the hex editor with the working S3 param, and noticed EFS Pro add some data to the beginning of the file. I removed this begining data and also the trailing zeros, and renamed it to param.bin (to go along with the name in kona3g.pit, perhaps not necessary). Finally, copied it by "dd if=/sdcard/param.bin of=/dev/block/mmcblk0p4" command, after couple of reboots white screen disappeared.
Solution for symptom 9:
Difficult to say this is a solution but it disappeared after this. In order to send for warranty claim, I restored the device to clean stock. First used Triangle Away to reset the counter. Booted and fully unroot via SuperSU. Then flashed the stock rom with the pit file, and without restart option. Shut down the device and boot into the recovery to do a full wipe, and the "No command" error wasn't there.
I must say, since my modem not working, capslock66's Android Reverse Tethering 3.15 saved my day to download the required Triangle Away add-on via laptop's broadband connection.
Since all other symptoms couldn't be solved my me after much effort, I sent the tablet for Samsung service.
WHAT IS THE USE OF .pit FILE?
.pit FILE IS USED TO DIRECT THE PARTITION OF THE WHOLE ANDROID SYSTEM..JUST LIKE WE ARE DOING GRUB IN PC...HERE ALSO WE NEED TO PARTITION THE SYSTEM FOR FLASHING THE FIRMWARE PROPERLY.. AND HERE THE .PIT IS USED
1. Get your phone into download mode..
2. connect to computer. Make sure that usb drivers installed and you have the firmware.tar file.
3. Now open odin 3.10
4. click on PIT and select ZEROLTE_USA_TMO.pit
5. Make sure that partition is tick
6. click on PDA and select firmware.tar file
7. Now start button and wait...You are done
link:
https://drive.google.com/folderview...tmV3YxMTB4WGpSZU5ReEI1WjZtUXM&usp=sharing_eid
Mhhh could be useful great job Op
The link doesn't work for me, could you reupload it? Also does this contain data about your /data partition? If so this might be specific to your model (16/32/64 GB)
update the file
update the file
SHATTAH said:
update the file
Click to expand...
Click to collapse
Just requested permission for the file.
SHATTAH said:
WHAT IS THE USE OF .pit FILE?
.pit FILE IS USED TO DIRECT THE PARTITION OF THE WHOLE ANDROID SYSTEM..JUST LIKE WE ARE DOING GRUB IN PC...HERE ALSO WE NEED TO PARTITION THE SYSTEM FOR FLASHING THE FIRMWARE PROPERLY.. AND HERE THE .PIT IS USED
1. Get your phone into download mode..
2. connect to computer. Make sure that usb drivers installed and you have the firmware.tar file.
3. Now open odin 3.10
4. click on PIT and select ZEROLTE_USA_TMO.pit
5. Make sure that partition is tick
6. click on PDA and select firmware.tar file
7. Now start button and wait...You are done
link:
https://drive.google.com/folderview...tmV3YxMTB4WGpSZU5ReEI1WjZtUXM&usp=sharing_eid
Click to expand...
Click to collapse
Can you please explain how you got the pit file? from what I understand you cannot simply dump the pit anymore unless I missed something.
requested access to this as well-- can you post somewhere other than Google Drive as people cant get to this file?!
can you please grant my request to download the file? I have a soft bricked phone and I really need the Pit file. thanks so much
looking a pit file for latest firmware 5.1.1 G925TUVU2COF6 does anyone have?
onlineunlocks said:
looking a pit file for latest firmware 5.1.1 G925TUVU2COF6 does anyone have?
Click to expand...
Click to collapse
According to: http://www.droidviews.com/how-to-extract-pit-file-from-samsung-galaxy-devices/
Requirement: To be able to use any of the methods described below [to extract the PIT file], you must have root privilege on your Galaxy device. Both the methods have been tested on the Samsung Galaxy S5.
Click to expand...
Click to collapse
This means that, unless someone gets it directly from Samsung somehow (leak, release, or otherwise), you'll need to wait for root on the 5.1.1 stock ROM.
I don't know a whole lot about the PIT file, and why someone would ever need it (apart from screwing around so much that you overwrite your partition information on the device... which would be hard for the average user to accidentally do).
Have you tried Samsung Smart-Switch? I don't know if it's capable, but it might download the PIT info from the internet before restoring stock firmware on a 100% borked device.
Thank you for the reply; by adb I know does not work without root as I looked over those methods. But there is also Heimdall that should be able to extract the pit while in download mode and has the option to save it,but seems not supporting this device. Also odin performs this tasks " Get PIT for mapping.." ,but does it automatically and there is no option to save from a working device with same details to use on other. I need it for a g925t that is stuck on samsung logo after odin restore and showing in download mode SW rev. check fail. device:2 binari 1 , and I think by flashing with a pit might fix it
onlineunlocks said:
Thank you for the reply; by adb I know does not work without root as I looked over those methods. But there is also Heimdall that should be able to extract the pit while in download mode and has the option to save it,but seems not supporting this device. Also odin performs this tasks " Get PIT for mapping.." ,but does it automatically and there is no option to save from a working device with same details to use on other. I need it for a g925t that is stuck on samsung logo after odin restore and showing in download mode SW rev. check fail. device:2 binari 1 , and I think by flashing with a pit might fix it
Click to expand...
Click to collapse
Let us know if this worked. I need to restore back to 5.0.2 also from 5.1.1. Thanks
will not work to restore to 5.0.2 from what I know and might also damage it,so do not recommend to try that
onlineunlocks said:
Thank you for the reply; by adb I know does not work without root as I looked over those methods. But there is also Heimdall that should be able to extract the pit while in download mode and has the option to save it,but seems not supporting this device. Also odin performs this tasks " Get PIT for mapping.." ,but does it automatically and there is no option to save from a working device with same details to use on other. I need it for a g925t that is stuck on samsung logo after odin restore and showing in download mode SW rev. check fail. device:2 binari 1 , and I think by flashing with a pit might fix it
Click to expand...
Click to collapse
I'm in the same situation.
Have you found a solution?
Aou said:
According to: http://www.droidviews.com/how-to-extract-pit-file-from-samsung-galaxy-devices/
This means that, unless someone gets it directly from Samsung somehow (leak, release, or otherwise), you'll need to wait for root on the 5.1.1 stock ROM.
I don't know a whole lot about the PIT file, and why someone would ever need it (apart from screwing around so much that you overwrite your partition information on the device... which would be hard for the average user to accidentally do).
Have you tried Samsung Smart-Switch? I don't know if it's capable, but it might download the PIT info from the internet before restoring stock firmware on a 100% borked device.
Click to expand...
Click to collapse
is this gonna fix my phone if efs is not mounted??? me and my buddy have no idea how he broke his phone.
Hey guys,
It seems more and more people are receiving the new version of the P8000:
- Stock Android 6
- New fingerprint scanner that is moved slightly higher and is able to unlock phone from screen-off (I confirm this is working)
- Sim 2 is combined with the micro-sd (I haven't tried whether you can have them both in at the same time)
- Somethings new about the display, since people are reporting errors with it after flashing older roms.
Warning: do NOT flash other roms. We have no way to unbrick the soft bricks yet!
---
Other topics that refer to this version:
http://forum.xda-developers.com/elephone-p8000/general/rom-p8000-t3431571
http://forum.xda-developers.com/elephone-p8000/help/stock-rom-p8000b-t3434477
http://forum.xda-developers.com/elephone-p8000/general/p8000-version-announced-t3346848
---
For development:
- The phone does not come pre-rooted. We have no way to flash custom recovery yet. Any tips for getting root? I've tried such tools as Kingo and vRoot, they don't work.
- We need the blocks file (scatter file) for SP Flash Tools. MTKDroidTools reports "unknown rom structure". Any help? Would love to start working on this.
Looking forward to hearing from others who have this version/who can help me with these questions.
Thanks!
Emile
Nice! Can you provide a dump from /system and /boot maybe?
BlueFlame4 said:
Nice! Can you provide a dump from /system and /boot maybe?
Click to expand...
Click to collapse
I would, if I knew how to. Any pointers?
Emileh said:
I would, if I knew how to. Any pointers?
Click to expand...
Click to collapse
Sure thing. On a rooted device, go into adb shell.
Then use "mount" command to check which partitions are mounted. One should be "/dev/block/platform/mtk-msdc.0/by-name/system" or similar. Use "dd if=/dev/block/platform/mtk-msdc.0/by-name/system of=/storage/emulated/0/system.img bs=1M" to dump the system to the internal sdcard to the file "system.img". If adb complains that bs=1M is an invalid option, try again without that one. A system dump can take some time where you will not get any feedback, so be patient there
Do the same for boot. So "/dev/block/platform/mtk-msdc.0/by-name/boot" should be the way to go for the path. I cannot tell the definite pathes on Android 6.0 but I am rather sure they are more or less like this.
If you run into troubles, just ask
BlueFlame4 said:
Sure thing. On a rooted device, go into adb shell.
Then use "mount" command to check which partitions are mounted. One should be "/dev/block/platform/mtk-msdc.0/by-name/system" or similar. Use "dd if=/dev/block/platform/mtk-msdc.0/by-name/system of=/storage/emulated/0/system.img bs=1M" to dump the system to the internal sdcard to the file "system.img". If adb complains that bs=1M is an invalid option, try again without that one. A system dump can take some time where you will not get any feedback, so be patient there
Do the same for boot. So "/dev/block/platform/mtk-msdc.0/by-name/boot" should be the way to go for the path. I cannot tell the definite pathes on Android 6.0 but I am rather sure they are more or less like this.
If you run into troubles, just ask
Click to expand...
Click to collapse
Thank you for your great instructions! The problem is that we've yet to achieve root on this device. We don't have a custom recovery for this version of the P8000 yet and other 'standard' methods of rooting don't work for me.
(I'm pretty solid in shell, so I'll do this afterwards, but I guess root is actually the first step).
// Edit to say: it does not come pre-rooted
Since the elephone support on facebook didn't realize there are two different versions of the P8000 available, I still need a ROM to unbrick my phone.
flo1k said:
Since the elephone support on facebook didn't realize there are two different versions of the P8000 available, I still need a ROM to unbrick my phone.
Click to expand...
Click to collapse
Ok, we know that, but doesn't really help us
Can you write them an e-mail?
I will do
Edit: OK, see if there will be an answer.
Thank you flo1k!
I have e-mailed as well, and would like to post on the Elephone forum, but don't seem to have access (because of minimum post count, I guess)
Anyone willing to ask for a ROM for the new P8000 on the forum there?
ROM Dump
@BlueFlame4
I can provide ROM dump in two versions:
1) a dump from adress 0000 0000 to 9d80 0000 (apr. 2.5 GB in one file)
2) a readback generated with the scatter.txt of the 'old' 5.1 stock ROM (apr. 2.8 GB seperated in 23 files)
FrauHofrat said:
@BlueFlame4
I can provide ROM dump in two versions:
1) a dump from adress 0000 0000 to 9d80 0000 (apr. 2.5 GB in one file)
2) a readback generated with the scatter.txt of the 'old' 5.1 stock ROM (apr. 2.8 GB seperated in 23 files)
Click to expand...
Click to collapse
The second choice looks promising
Maybe a stupid question
where shall I upload the files - any preferred webspace?
I'm uploading the files - because they contain my NVRAM I send the link as PM as soon as the upload is finished
FrauHofrat said:
Maybe a stupid question
where shall I upload the files - any preferred webspace?
I'm uploading the files - because they contain my NVRAM I send the link as PM as soon as the upload is finished
Click to expand...
Click to collapse
Are you sure we're talking about the same version of the P8000? Cause as far as I know there isn't 5.1 available for this version... Right?
Just checking thank you for your help in any case!! Really looking forward to it.
// edit: ah, you just used the old scatter file. But does that one work for this version?
Emileh said:
Are you sure we're talking about the same version of the P8000? Cause as far as I know there isn't 5.1 available for this version... Right?
Click to expand...
Click to collapse
No, there is only one Firmware available - the mysterious P8000_6.0_20160516.
Btw, this Phone contains a new mainboard model "K06TS-L-V2.0.3" - the 'old' mainboard is moder "K05T...."
// edit: ah, you just used the old scatter file. But does that one work for this version?
Click to expand...
Click to collapse
No, it doesn't work resp. the phone boots with this firmware, but the LCD-driver is the wrong one - the display only shows coloured lines and blurry spots. And there are probabely some more bugs ....
FrauHofrat said:
No, there is only one Firmware available - the mysterious P8000_6.0_20160516.
Btw, this Phone contains a new mainboard model "K06TS-L-V2.0.3" - the 'old' mainboard is moder "K05T...."
No, it doesn't work resp. the phone boots with this firmware, but the LCD-driver is the wrong one - the display only shows coloured lines and blurry spots. And there are probabely some more bugs ....
Click to expand...
Click to collapse
But if the phone boots with the firmware, doesnt that mean that the scatter file of the regular P8000 works? Since it flashes the firmware correctly.
The problem is that I was not able to flash the 'readback files' to the faulty phone.
When selecting 'Only Download' at SP-Flashtool I got the error "PMT... must be download"
When selecting 'Firmware Upgrade" I got some BROM error code
In both cases I used the same scatter,txt which I used to 'readback' the firmware from the working phone
Actually I have to correct my statement in post #15:
I flashed the faulty phone with the last 5.1 stock ROM (160711) - with this stock ROM the phone boots up but LCD (and probably more things) is not working.
I have actually gotten alot further
You have the use the scatter.txt from Android 6.0, which works perfectly fine. I have been able to extract boot.img, system.img and recovery.img that way (using Readback in SP Flash Tools)
Which ones do you need?
They probably flash fine (only thing I've flashed so far are custom recoveries, and although my ported PhilZ starts, I havent gotten it to mount anything.)
A little warning: don't use anything that has anything to do with Android 5.1. Those scatter files don't work
These are great news!
"Which ones do you need?"
Probably all of them
Ok this contains the scatter file, preloader, system.img, boot.img and stock recovery.img
https://ehaffmans.stackstorage.com/index.php/s/uKGKCir0BociydU
You need SP Flash Tools v5, select the scatter file first, then deselect everything, and only select these 4 and manually select the correct files.
Btw, the name of the preloader file is wrong, don't worry. It came from this phone
I am of course not responsible for anything!
Can you guys please confirm this doesn't contain anything personal? Like personal files or IMEI or something. Thanks!