Related
please help out here....my phone get stucked to HTC logo...i have just left my phone lower battery to 10% then after charging it wont boot up properly...anyway, the battery is still charging...am able to upload RADIO rom with the trick like holding down the reset+back+reset...able to upload RADIO rom but after booting up still stucked in HTC logo.....pls advise...dont know what to do now....have even tried removing SIM card...pls HELP...
What happens if you hold down the volume button while booting your device?
will try it here....holding the volume down? pls reply asap....thanx for helping
its not really reacting with any button once it get stucked to HTC logo
yea, to boot into the bootloader.
If you hold down the "volume button down" while booting your device it must show the colored screen within a second. Just hold down the "volume down" while pressing the reset button on the back. Keep holding the "volume down" till you see the colored screen.
tell me how please...i will have to remove the battery and put it back in...then it will still charge.....anyway...the only way i can start there is to press the power button and it will start up....but it will get stuck in HTC logo....when do i start going to bootloader in there....pls help...
Have you not tried a hard reset yet?
If that still does not work the flash a new ROM - while connected via bootloader ( only way )
i can still go to bootloader here sir....thanks for staying with me.....then what should i do next
wencyv said:
tell me how please...i will have to remove the battery and put it back in...then it will still charge.....anyway...the only way i can start there is to press the power button and it will start up....but it will get stuck in HTC logo....when do i start going to bootloader in there....pls help...
Click to expand...
Click to collapse
Remove the battery, place the battery, hold down the "volume down" button, start your device ( while still holding the "volume down" button ).
Try a hard reset first as mentioned above:
Hold down the "volume down" button + the round button on the front, then reset your device while still holding those two buttons.
wencyv said:
i can still go to bootloader here sir....thanks for staying with me.....then what should i do next
Click to expand...
Click to collapse
Download a ROM and flash it while the device is still in that mode.
wencyv said:
tell me how please...i will have to remove the battery and put it back in...then it will still charge.....anyway...the only way i can start there is to press the power button and it will start up....but it will get stuck in HTC logo....when do i start going to bootloader in there....pls help...
Click to expand...
Click to collapse
1. restart the phone (with the pen in the small red button at the pen hole)
2. immediately after you have restarted, hold down the volume down button.
3. now you should be in three color bootloadermode.
4. connect your usb cable (after that you will see USB at the white color part)
5. start your custom ruu to flash your new rom.
good luck
edit..
aaaa u solved it while i was writting
great.
To hard reset -
reset your device with the stylus the before anything appears on the screen hold down the Vol down key and the centre button - follow the instructions - but don't use the volume down option unless you want to format you internal memory too.
have you tried to reflash rom? another rom possibly?
trying to do hard reset again...and this time it applies....dont know why it's not reacting awhile ago....
wencyv said:
trying to do hard reset again...and this time it applies....dont know why it's not reacting awhile ago....
Click to expand...
Click to collapse
Who cares as long as it will work
you know what....iam able to revive it....tahnx for staying here...next time...i know what to do next....
job done
thread closed
hello to everybody, i'm new here
i just wanted to unlock my universal. i read the instructions in the readme of the downloaded file from here (Source) carefully and wanted to enter the bootloader.
but after i press the power, light and reset button simultaneously like here: Image ...it just restarts (like i only press the reset key).... --> no bootloader apers
anybody knows the reason why it doesn't start the bootloader? thank u for helping
hi, welcome to forum. sometimes can be tricky. but if you hold the buttons then press reset and continue holding for a couple more seconds then it should load the bootloader. hope this helps
thank u for ur quick answer!
i'm holding power and light button simultaneously and then i push the reset button. it seems to be not working.. like it ignors that i'm pressing the other buttons...?
hi, tried with mine. if i hold the light and power and when i press reset and hold it also it enters bootloader. if this doesnt work sorry maybe a more experienced user can enlighten us.
solved the prob
power is working. reset is working. if you press the light and backlight settings come up then thats working depending on your rom. not sure what your issue is if they all work.
ok solved the problem with a trick. now everything is working. thank you for ur help!
BAD Flash when updating radios, who can I pay to fix this?
Or anyone know of a way to fix this?
It appears to be bricked
When I flashed the ATT_Radio_Rhodium_4.48.25.95, I didn't rename it to RUU_Signed
Now I get nothing when I restart the phone, just a black screen.
[email protected] said:
BAD Flash when updating radios, who can I pay to fix this?
Or anyone know of a way to fix this?
It appears to be bricked
When I flashed the ATT_Radio_Rhodium_4.48.25.95, I didn't rename it to RUU_Signed
Now I get nothing when I restart the phone, just a black screen.
Click to expand...
Click to collapse
is your phone a gsm rhodium or does it have a cdma module too?
Both I believe
This happened to me last night. I reflashed the ROM to fix it. I used MightROM which is FRIGGIN' Awesome if you ask me
In order to do that though you need to be CID unlocked though but basically as long as you are in the bootloader/bios then you can flash the new ROM from your PC via the USB. If you need any links to that stuff I can post, but I am not quite sure if this would be part of XDA or not (Is MightROM xda? Idk? PPCGeeks??)
You can also try holding down the Call answer and Call end buttons at the same time with the power button then put your battery in. This didn't work for me though, but I had to do this anyways after I flashed the ROM so it might work.
edit: Sorry I misread. I am not sure about the Black Screen. Might work though. I was in the bootloader/tricolor to reflash. Maybe your LCD is dead or something for all I know. Sorry Mate.
[email protected] said:
Both I believe
Click to expand...
Click to collapse
oh god then you flashed a GSM radio to a CDMA worldphone (just because it has a GSM module doesn't mean you can flash a GSM carrier radio to it... nope!!)
if you plug it into the PC does the PC try to install some USB driver?
[email protected] said:
BAD Flash when updating radios, who can I pay to fix this?
Or anyone know of a way to fix this?
It appears to be bricked
When I flashed the ATT_Radio_Rhodium_4.48.25.95, I didn't rename it to RUU_Signed
Now I get nothing when I restart the phone, just a black screen.
Click to expand...
Click to collapse
It is simple. You obviously have a CDMA device. It doesn't matter if you use it on a GSM network. Your device is and always will be a CDMA device. NEVER try to flash ANYTHING GSM on it or you run the risk of permanently bricking it.
To fix this, you will need to grad the latest ROM update from either HTC's website, or your carrier's website. Put the device into bootloader mode by holding down the power button and pressing the tiny reset button under the battery cover with your stylus. Once it boots into the tri-colored screen (bootloader), you can then run the ROM update utility that you just downloaded. This will restore everything back to stock settings and you can try again. If you have already done Hard SPL, then it will NOT be overwritten, so don't worry.
Update
I cannot get into the tri-colored screen (bootloader).
How long do I need to hold in the reset and power button?
More than 1 min?
[email protected] said:
I cannot get into the tri-colored screen (bootloader).
How long do I need to hold in the reset and power button?
More than 1 min?
Click to expand...
Click to collapse
You can't get there, because you're doing it wrong. You need to hold down the volume down button and then press the reset button once. This gets you into the bootloader.
Update
Holding down the volume down button and then pressing the reset button once, did not work for me.
How long do I hold the volume down button for?
[email protected] said:
Holding down the volume down button and then pressing the reset button once, did not work for me.
How long do I hold the volume down button for?
Click to expand...
Click to collapse
Do you have power in the device? You need to have a battery in it. Also, the reset button might not power your device on. If your device doesn't turn on when you press the reset button, then just hold the volume down button and press the power button once instead. That ought to do it.
Hi,
My One X was working fine with my custom firmware for about six months but then it suddenly bricked itself by booting into HBOOT and now the up volume key and power button both move the selection down while the down volume key does nothing. When I turn the phone off it just reboots into HBOOT. For it to turn off I have to wait for the battery to run out, but that doesn't help with anything.
My computer doesn't seem to recognise the phone either, even though I haven't really changed anything since I rooted it and flashed the new rom. I have no idea what to try now, any help?
No one has any advice? Does this mean it is completely bricked?
Astiolo said:
No one has any advice? Does this mean it is completely bricked?
Click to expand...
Click to collapse
maybe your volume buttons are broken, have some problem here in the forum try open the HOX and see if they are not stuck or durty
Thant said:
maybe your volume buttons are broken, have some problem here in the forum try open the HOX and see if they are not stuck or durty
Click to expand...
Click to collapse
I thought that was unlikely but I finally got around to testing anyway and the phone booted up properly when I unplugged the ribbon which includes the volume buttons. I guess the down volume button must have been stuck on which is why the phone continually booted into HBOOT and the down volume key didn't do anything when it was pressed. I guess the way the menu HBOOT menu is programmed meant that pressing the other buttons didn't do anything but upon release it registered the down button again.
Anyway, I replaced that part of the phone and it's all in working order. Thanks for the tip.
Hi! Anybody knows how to enter recovery mode on this device? I looked trough the forum but holding a reset button till the other buttons lights are flashes, not work, also tried to hold it 25 sec and when it boots up press the reset button again doesn’t work. So any ideas welcome!
Thanks!
It is a PX5 unit Cortes a53 chip, and no buttons apart the reset button.
benicsalad said:
Hi! Anybody knows how to enter recovery mode on this device? I looked trough the forum but holding a reset button till the other buttons lights are flashes, not work, also tried to hold it 25 sec and when it boots up press the reset button again doesn’t work. So any ideas welcome!
Thanks!
It is a PX5 unit Cortes a53 chip, and no buttons apart the reset button.
Click to expand...
Click to collapse
After hold reset button for x seconds you have to release and press immediatly not to wait after reboot.
AlexRuhl said:
After hold reset button for x seconds you have to release and press immediatly not to wait after reboot.
Click to expand...
Click to collapse
I tried that one as well, but nothing, and still a question how long i need to hold the reset button?
benicsalad said:
I tried that one as well, but nothing, and still a question how long i need to hold the reset button?
Click to expand...
Click to collapse
Hold reset button until led keys are blinking. This method works for me( radio without phisical buttons like you)
AlexRuhl said:
Hold reset button until led keys are blinking. This method works for me( radio without phisical buttons like you)
Click to expand...
Click to collapse
I tried to hold the reset button for 30 sec but the led keys are not blinking, this is my issue, I looked trough the forum, YouTube but can find any solution.
I asked the seller but nothing back at the moment. Wanna go back to android 6 form android 8, and without recovery mode don’t know how
benicsalad said:
I tried to hold the reset button for 30 sec but the led keys are not blinking, this is my issue, I looked trough the forum, YouTube but can find any solution.
I asked the seller but nothing back at the moment. Wanna go back to android 6 form android 8, and without recovery mode don’t know how
Click to expand...
Click to collapse
Could you please post a screenshoot of information of radio?
AlexRuhl said:
Hold reset button until led keys are blinking. This method works for me( radio without phisical buttons like you)
Click to expand...
Click to collapse
AlexRuhl said:
Could you please post a screenshoot of information of radio?
Click to expand...
Click to collapse
Here it is, thank you for your help and time!
benicsalad said:
Here it is, thank you for your help and time!
Click to expand...
Click to collapse
I have an idea: put on sd an .img file corrupted and try to upgrade mcu..radio will go to recovery and stop here because the file is invalid..after you can put an sd card with what you need to downgrade
Can I just downgrade, because I think it is a different file system under android 8. I can download an app what put the radio into recovery mode, but i’m not sure downgrade is that easy,so I downloaded malaysk rom (android 6) already, do you think it will be strait forward?
Yes I downgraded with a stock rom with make a autostart sd(see the discussion like upgrade) only put sd and wait
AlexRuhl said:
Yes I downgraded with a stock rom with make a autostart sd(see the discussion like upgrade) only put sd and wait
Click to expand...
Click to collapse
It didn’t work out exactly how I planned, but I ended up in recovery mode somehow and eventually downgraded my unit, thank you for you time and effort
Radio navigation gps hyundai elantra 2011-2014.
Hello. Does anyone know how to reset the multimedia station RADIO NAVIGATION GPS HYUNDAI ELANTRA 2011-2014. A-Media Auto 1024x600 Android 6.0.1 px5 I Need to perform a hard reset to enter recovery after upgrading to Android 8 px5
benicsalad said:
It didn’t work out exactly how I planned, but I ended up in recovery mode somehow and eventually downgraded my unit, thank you for you time and effort
Click to expand...
Click to collapse
How did you manage to enter recovery?Fake .img or .zip on usb?
tokesszabi said:
How did you manage to enter recovery?Fake .img or .zip on usb?
Click to expand...
Click to collapse
Hi same question here...
Im not sure, I used one of the downloaded image and I ended up there, sorry guy, car sold with the unit.
My device is completely broken and the system does not boot. How to go to recovery mode? Even the buttons no longer work, only the boot image
HI, my Dasaita MAX10 is in boot loop animation. I want to go to recovery, i see flashing touchbutton pressing reset button at startup (ignition on) but then I can't see recovery even if I release and press the reset button. Does someone have the same issue ?
angelopellef said:
HI, my Dasaita MAX10 is in boot loop animation. I want to go to recovery, i see flashing touchbutton pressing reset button at startup (ignition on) but then I can't see recovery even if I release and press the reset button. Does someone have the same issue ?
Click to expand...
Click to collapse
I had the same issue.
Was able to boot recovery from SD-Card
[MTCD/E] Android 10 upgrade using official Free tools
To upgrade a MTCD/E PX3, PX5, PX6 from Android 6+ on using official Rockchip free tools - a reminder, bringing together multiple threads. First note - if coming from Android 6 - early versions of Realtek dual BT/WIFI (type 2) are not supported...
forum.xda-developers.com
In this recovery I was able to flash a current Firmware and got it working again.