Desire frozen on htc screen - Desire Q&A, Help & Troubleshooting

Hello everyone,
I have a problem with my HTC desire.
I was running Leedroid for more than 6 months and everything was fine.
Yesterday morning, my phone went battery-dead and then when I started it plugin-in to the power socket it turned on and got stuck at the HTC screen.
I can enter bootloader (I guess ?) by pressing power + back but then I don't know what to do (I have a white screen with several menus I can browse with vol up/down) ?
I also tried going with a RUU (RUU MoDaCo Version: 1.15.405.4) and it does detect my phone but won't finish.
Is there anything I can do ?
Geeum

Geeum said:
Hello everyone,
I have a problem with my HTC desire.
I was running Leedroid for more than 6 months and everything was fine.
Yesterday morning, my phone went battery-dead and then when I started it plugin-in to the power socket it turned on and got stuck at the HTC screen.
I can enter bootloader (I guess ?) by pressing power + back but then I don't know what to do (I have a white screen with several menus I can browse with vol up/down) ?
I also tried going with a RUU (RUU MoDaCo Version: 1.15.405.4) and it does detect my phone but won't finish.
Is there anything I can do ?
Geeum
Click to expand...
Click to collapse
Why won't it finish?

No idea, it doesn't say.
I believe my phone is soft bricked, I can access hboot and fastbood so i'm pretty sure I can do something about it.
I read something about a unbrick thing you could launch from fastboot ? But can't find it.
Geeum

Try to flash this ruu:
http://shipped-roms.com/download.ph...9.00.32U_5.11.05.27_release_151783_signed.exe
Boot phone in fastboot mode and follow instructions on the screen. Does it give you any errors?

Everything goes well, it does the sending part then gets stuck at signature update:
ERROR [132]: SIGNATURE ERROR
The ROM Update Utility cannot update your Android Phone.
Please get the correct ROM Update Utility and try again.
Click 'Exit' to quit.
Geeum

FYI I tried to create a gold card but adb devices doesn't return anything so I don't know if I can create a goldcard.
fastbood devices does return something though.

Geeum said:
FYI I tried to create a gold card but adb devices doesn't return anything so I don't know if I can create a goldcard.
fastbood devices does return something though.
Click to expand...
Click to collapse
Adb will run only if adb debugging is allowed, so Booted state or recovery state. In fastboot mode, only Fastboot will run. Have you overwritten recovery yet? If not, you flash another rom. If yes, are you S-Off? If so, you can flash an Hboot/recovery in Fastboot mode

droidzone said:
Have you overwritten recovery yet?
Click to expand...
Click to collapse
I think I did. I downloaded ClockworkMod Recovery and put it in my tools folder then typed 'fastboot flash recovery /path/to/<recovery>.img':
C:\android-sdk-windows\tools>fastboot flash recovery recovery-clockwork-2.5.1.8-bravo.img
sending 'recovery' (3412 KB)...
OKAY [ 0.563s]
writing 'recovery'...
(bootloader) signature checking...
FAILED (remote: signature verify fail)
finished. total time: 0.922s
droidzone said:
If not, you flash another rom.
Click to expand...
Click to collapse
How ? I tried to put another ROM at the root of my sdcard but not sure how to go from then on. Here is whet I tried, with leedroid v2.5:
C:\android-sdk-windows\tools>fastboot update leedroid.zip
archive does not contain 'android-info.txt'
archive does not contain 'android-product.txt'
error: update package has no android-info.txt or android-product.txt
droidzone said:
If yes, are you S-On?
Click to expand...
Click to collapse
Don't know what S-On means ?
droidzone said:
If so, you can flash an Hboot/recovery in Fastboot mode
Click to expand...
Click to collapse
Can you tell me more ?
Thanks for your help it's greatly appreciated.
Geeum

Geeum said:
I think I did. I downloaded ClockworkMod Recovery and put it in my tools folder then typed 'fastboot flash recovery /path/to/<recovery>.img':
C:\android-sdk-windows\tools>fastboot flash recovery recovery-clockwork-2.5.1.8-bravo.img
sending 'recovery' (3412 KB)...
OKAY [ 0.563s]
writing 'recovery'...
(bootloader) signature checking...
FAILED (remote: signature verify fail)
finished. total time: 0.922s
How ? I tried to put another ROM at the root of my sdcard but not sure how to go from then on. Here is whet I tried, with leedroid v2.5:
C:\android-sdk-windows\tools>fastboot update leedroid.zip
archive does not contain 'android-info.txt'
archive does not contain 'android-product.txt'
error: update package has no android-info.txt or android-product.txt
Don't know what S-On means ?
Can you tell me more ?
Thanks for your help it's greatly appreciated.
Geeum
Click to expand...
Click to collapse
You cant flash custom roms from fastboot
You can flash recovery, and each of the .img files included in the Clockworkmod backup folder, but only if you're S-off. Apparently you're S-On (Security on. For S-off, Alpharev should have been used)..
Were you foresighted enough to make a gold card? If you hadnt, you have to find the RUU you successfully flashed last, or the RUU corresponding to the region of your device and brand.
You can read more on two of the threads I started. Click on my userid, and choose "Threads started by DZ". Look for "How to unbrick an SLCD Desire (which works for AMOLED too)" and "How to unroot" both of which should give you a comprehensive idea of how to approach your problem. Any queries pertaining to those threads can be asked there, or after reading it, here.

droidzone said:
You can read more on two of the threads I started. Click on my userid, and choose "Threads started by DZ". Look for "How to unbrick an SLCD Desire (which works for AMOLED too)" and "How to unroot" both of which should give you a comprehensive idea of how to approach your problem. Any queries pertaining to those threads can be asked there, or after reading it, here.
Click to expand...
Click to collapse
I tried, but when I click on your name I can only click on "Find all posts by droidzone" and there are 40 pages of them
Can you maybe send me the link to the posts you mention ?
Geeum
[edit] found the how to unroot one, reading it now. (http://forum.xda-developers.com/showthread.php?t=880268)
[edit 2] found the 2nd one: http://forum.xda-developers.com/showthread.php?t=831734

Geeum said:
I tried, but when I click on your name I can only click on "Find all posts by droidzone" and there are 40 pages of them
Can you maybe send me the link to the posts you mention ?
Geeum
[edit] found the how to unroot one, reading it now. (http://forum.xda-developers.com/showthread.php?t=880268)
Click to expand...
Click to collapse
Hmm.. You should learn your way around the forum!
But here they are:
http://forum.xda-developers.com/showthread.php?t=831734
http://forum.xda-developers.com/showthread.php?t=880268

I did find them in the end
I extracted the PB99IMG.zip and put in on my SDCARD but after loading and checking I get:
CID incorrect!
Update Fail !
I don't have a goldcard
I read on your posts that I can take my sdcard to another DESIRE phone and make it a goldcard so I'll try that tomorrow.
Any other idea ?
Geeum

Geeum said:
I did find them in the end
I extracted the PB99IMG.zip and put in on my SDCARD but after loading and checking I get:
CID incorrect!
Update Fail !
I don't have a goldcard
I read on your posts that I can take my sdcard to another DESIRE phone and make it a goldcard so I'll try that tomorrow.
Any other idea ?
Geeum
Click to expand...
Click to collapse
Making a goldcard is the solution. And you can get the CID from any Android phone.

You definitely need to create a gold card. To create a goldcard see this: http://www.nazriawang.com/2010/04/ho...th-ubuntu.html
It is in unbutu, but maybe you can sort it out. Have a look.

OK I now have a goldcard: took a friends phone (same phone, same carrier) and put my sdcard in there and used modaco's tool.
Now the next step is to install a valid RUU for my region, right ?
If I do so it seems to go past the last error but gets stuck at
ERROR [140]: BOOTLOADER VERSION ERROR
Thanks

Hello ! I tried using a different RUU (the one suggested bu MatDroid: RUU_Bravo_Froyo_HTC_WWE_2.29.405.2_Radio_32.49.00.32U_5.11.05.27_release_151783_signed) and it has -almost- worked !
The update went until the end but now my phone boots and reboots after a couple of seconds (not fixed: sometimes I can go to unlock my simcard, sometimes a bit longer ...)
I'm getting desperate everytime I think I'm making advance there something new.

Now what ? I'm gone back to the original state: frozen on HTC screen
I tried re-running the RUU (this time the latest I could find: RUU_Bravo_Froyo_HTC_WWE_2.29.405.5_Radio_32.49.00.32U_5.11.05.27_release_159811_signed.exe)
Everything goes well, it says it is successful but then it reboots and gets stuck with HTC screen

Hey guys, went to the bootloader and erased all data. This time for some reason it rebooted fine and now the phone seems to be working.
Now I would like to have some advice:
- What can I do so in the future I have all I need for recovering ?
- I already have a goldcard
- what about the recovery ? Should I install something ?
- I liked leedroid, so thinking of going back to 2.5 what do you think?
Thanks for your help you re the best !
EDIT: well I thought it was working but here I am again. Reboot after reboot. This time the first one happened after 15 solid minutes and now it reboots every 30 seconds I barely have the time to enter my pincode ...

Anyone has an idea ?
I've found a way to stabilize my phone, which is by not putting my SIMcard in, but not sure how long it's gonna take before the next reboot.
I don't know what to do. Was thinking in downgrading using teppic74 tool but everytime I download it I get an error: corrupted file.
Can't see the end of it.

Guys, in the end I re-did the whole process: use RUU then delite data in the recovery and it seems to work.
I guess those RUU don't always work fine the first time.
Thanks to you all for your help

Related

[Q] Stuck on S-Off Screen

Hi, i've been using LeeDroid for a few months now and all has been well, however yesterday my Desire turned itself off and now won't come back on. Each time i try and power it up it freezes at the Alpharev S-Off screen. I went into the menu's with volume down + power, but i can't get into my recovery - it takes me to the same frozen screen as does trying to reboot etc. And i don't think it's being recognized by usb either. So i really don't know what to do now.. is my phone bricked? I was a complete noob before rooting and flashing a custom rom before, so now that i've hit a problem i'm clueless all over again. Any help would be greatly appreciated
can you use fastboot? If so just flash a new recovery and all should be fine... chill out it can be fixed
What would i need for that? That's going into new territory
j3nni said:
What would i need for that? That's going into new territory
Click to expand...
Click to collapse
Can you access recovery? If no can you access bootloader (vol down + power on)
I can get onto the menu with the options 'fastboot, recovery, clear storage and simlock' if that's what you mean? The recovery option takes me back to my frozen alpharev screen, but i can get onto fastboot and after reading around i can get my pc to recognize it from fastboot usb from my pc using cmd.. Am i going the right direction at all? Eek. What i don't get now is the recovery image i'm supposed to use
j3nni said:
I can get onto the menu with the options 'fastboot, recovery, clear storage and simlock' if that's what you mean? The recovery option takes me back to my frozen alpharev screen, but i can get onto fastboot and after reading around i can get my pc to recognize it from fastboot usb from my pc using cmd.. Am i going the right direction at all? Eek. What i don't get now is the recovery image i'm supposed to use
Click to expand...
Click to collapse
Use amon_RA ... Download and flash onto ur phone and ur phone should be fixed
Plenty of guides around man, good way of learning fastboot
to use fastboot you need to download several things. Instead of using fastboot with cmd, I'd just recommend using fastboot commander, which does the job for you. In order to use that however, you will need the adb drivers, and Java SDK.
Once you've got all that, simply boot into fastboot, run "fastboot commander.exe", go into the "misc" tab, wipe Recovery, system, cache, boot, and userdata. Once you've done that download recovery, navigate to the "Hboot, radio & Rec" tab on fastboot commander, select recovery, find the recovery.img you just downloaded, and flash it. Once you've done that just boot into recovery and install any ROM you want.
Thanks for the replies guys. I did what you said to do (using fastboot commander), and when trying to boot into recovery to install my ROM it froze again at the alpharev screen. I'm stuck again now. When the files show up as you turn on into fastboot, i'm getting this..
SD Checking...
Loading...[PB99DIAG.zip]
No Image!
Loading...[PB99DIAG.nhh]
No Image or Wrong Image!
Loading...[PB99IMG.zip]
No Image!
Loading...[PB99IMG.nhh]
No Image or Wrong Image!it's saying my pb****.img files arn't found
which i gather can be normal. Other than that i'm stumped again
j3nni said:
Thanks for the replies guys. I did what you said to do (using fastboot commander), and when trying to boot into recovery to install my ROM it froze again at the alpharev screen. I'm stuck again now. When the files show up as you turn on into fastboot, i'm getting this..
SD Checking...
Loading...[PB99DIAG.zip]
No Image!
Loading...[PB99DIAG.nhh]
No Image or Wrong Image!
Loading...[PB99IMG.zip]
No Image!
Loading...[PB99IMG.nhh]
No Image or Wrong Image!it's saying my pb****.img files arn't found
which i gather can be normal. Other than that i'm stumped again
Click to expand...
Click to collapse
try do a full wipe of everything like I've mentioned before and then a different HBOOT
Okiedoke, how do i use a different hboot? And where do i find one from? At the moment i believe it's 0.93
j3nni said:
Okiedoke, how do i use a different hboot? And where do i find one from? At the moment i believe it's 0.93
Click to expand...
Click to collapse
www.alpharev.nl download a HBOOT and flash it through fastboot. Just make sure to check MD5 (you need a MD5 utility AFAIK)
I'm not sure which one is the right one for my ROM, i'm using LeeDroid.. Sorry for all the questions!
j3nni said:
I'm not sure which one is the right one for my ROM, i'm using LeeDroid.. Sorry for all the questions!
Click to expand...
Click to collapse
For any sense UI ROMs you would use the Sense HBOOT, remember to nandroid backup before you do so! because you might find that you get a bootloop after flashing the HBOOT.
And don't worry about asking questions! it's what we're all here for.
By the way if you don't know what different HBOOTs do: they change the partition sizes for /system /cache and /data. So by using a different HBOOT instead of the stock one you may get more storage for apps etc. if you choose one with a larger /data partition.... if that makes sense
Ok the sense one it is =)
Ah i see! Thanks for explaining cos underneath the nerd in me would have been wondering what it did lol.
Not sure how to get a nandroid done when i can't get into recovery though
I still havn't got anywhere with my problem, if anyone could advise me further i'd really appreciate it, as this is really stressing me out now.
The only screen i can still ever see is a frozen alpharev screen, and i still can't enter recovery. I've cleared everything using fastboot commander and flashed a new recovery which did nothing. Then i took the next advice and flashed a new hboot. The hboot has changed on my hboot menu (vol down + power) but still goes to the frozen alpharev screen when i try to go to recovery or turn the phone on. I then flashed a LeeDroid rom, which came up with an error at the end of it..
"sending 'zip' (173060 KB)... OKAY [ 23.469s]
writing 'zip'... FAILED (remote: not allowed)"
And that's as far as i've got.
Reading further i've been trying to work out how to flash a stock ruu to see if that works. However my phone was a branded Orange UK phone before so there is no ruu for that. So my question is, bearing in mind i can't get into the phone at all, how can i go about downgrading the hboot and installing a htc stock ruu. Can anyone point me to the right files i would need. I really don't know what i'm doing and i think the amount of searching i've been doing is just confusing me further
j3nni said:
I still havn't got anywhere with my problem, if anyone could advise me further i'd really appreciate it, as this is really stressing me out now.
The only screen i can still ever see is a frozen alpharev screen, and i still can't enter recovery. I've cleared everything using fastboot commander and flashed a new recovery which did nothing. Then i took the next advice and flashed a new hboot. The hboot has changed on my hboot menu (vol down + power) but still goes to the frozen alpharev screen when i try to go to recovery or turn the phone on. I then flashed a LeeDroid rom, which came up with an error at the end of it..
"sending 'zip' (173060 KB)... OKAY [ 23.469s]
writing 'zip'... FAILED (remote: not allowed)"
And that's as far as i've got.
Reading further i've been trying to work out how to flash a stock ruu to see if that works. However my phone was a branded Orange UK phone before so there is no ruu for that. So my question is, bearing in mind i can't get into the phone at all, how can i go about downgrading the hboot and installing a htc stock ruu. Can anyone point me to the right files i would need. I really don't know what i'm doing and i think the amount of searching i've been doing is just confusing me further
Click to expand...
Click to collapse
Hi.
As I can see the only way to restore is using a RUU to go back to stock then root and S-Off the phone again.
First: Preparation.
1. If you have a custom HBOOT (e.g.: 6.93.0001) you need first to flash the HBOOT Downgrader (found on alpharev site), then flash the RUU.
2. You will gonna need a Gold Card if your phone was branded.
Second: Starting
1. Make your Gold Card using someone's else phone (it has to be running Android) - the Gold Card is unique per SD Card, not per phone.
2. Use this tool to make the Gold Card: HERE
3. Guide how to make a Gold Card in Linux: HERE
4. get the latest RUU WWE 2.29.405.5. Extract the PB99IMG.zip file from the RUU: here it is how: http://forum.xda-developers.com/showthread.php?t=880268 -2nd post.
5. Reboot in bootloader (Volume-Down + Power)
7. Select fastboot
8. Flash the HBOOT Downgrader (don't forget to check the MD5 of the file you have downloaded from alpharev)
9. Extract the PB99IMG.zip and put it on root of SD Card.
10. Reboot in bootloader (scroll to REBOOT and select)
11. It will automatically load the img and ask you if you want to install
12. Check Yes and follow onscreen progress.
13. Wait untill it finnishes
14. I think it will reboot itself, if not scroll down to the Reboot obtion and press Power button to select.
IMPORTANT WARNING!!!
droidzone said:
Whatever you do, DO NOT turn off the device manually unless the software tells you to. If something goes wrong, dont switch off phone. Keep the phone on while trying a solution. Newer RUUs dont usually wreck a phone, and with a goldcard, you can always recover. But, the flash SHOULD NOT be interrupted by switching off or disconnecting the cable.
Always start with a battery with >50% power (full recommended).
Click to expand...
Click to collapse
Or if you want to go to stock and it is an unbranded phone you can just run ur ruu when the phone is in fastboot
Sent from my HTC Desire using XDA App
Think i may be the happiest girl in the world today lol i finally got it all fixed. I had a bit of trouble making the goldcard as at first my sd card kept saying it needed to be reformatted after, but after formatting it with SD Formatter program rather than Vista's own, it worked. All the rest went without a hitch. Now just gotta root, s-off and grab my new ROM and this past week can all get forgotten about =)
Thankyou so much to everyone that helped!
Incase anyone does read this far, is the procedure still the same as when i first used it back in April.. from here? http://forum.xda-developers.com/showthread.php?t=1016084
It is still the same.
If you like sense -
http://forum.xda-developers.com/showthread.php?t=1054435
░█░ [ROM][28/06] ✰.Reflex S v2.1.7 Gingerbread 2.3.3· ░█░ · |SenseGingerB 2.1+3.0|
You might like it...

Rom Advice / Steps please

Good Afternoon everyone,
Here once again. I have been having lots of problems recently with my phone memory getting low, crashes freezing, un-expected reboots etc. I have been using the same rom for a few months and was fine at first but just broke down. So I went into recovery and did a wipe now when powered on for the first time it doesnt get past boot animation just stay on the screen no matter how many reboots or further wipes. I also got a brand new 32GB Micro SD card for xmas that I haven't used yet so my idea was to get a new cool rom and use the SD card
First of all which rom. Now I know people say try different roms and see which you like but so many roms I dont know what to go for and was wondering for some advice. My requirements are that it is not ICS version as I get a phone upgrade on contract in July and want to leave ICS for a new phone so Gingerbread it is.
Now the rom requirements are:
> HTC Sense, prefferably a latest 3D version but if it doesn't work or very laggy then no.
> Camera needs to be fully working
> USB Tethering
> As much as possible on the SD card to save phone space
> Dont need super battery life but at least something that lasts a day and doesnt drain it
> Music Working nicely
> Not too buggy and fairly stable
Now secondly I still have not got myself familiar with Android flashing etc. If I want to start again from scratch new memory card does anyone know the steps. Is there any plain step by step instructions out there that tells me completly what I need to do as I can get confused quite easily.
Thanks in advance for any responses,
Regards,
Max
For this moment(in my opinion) this is the one from the best ROM for HTC Desire...including everything what you questing...
http://forum.xda-developers.com/showthread.php?t=1315961
Thanks. I was already interested in this rom and you saying that has swayed by boat. The next problem is how to go about it. the first steps appears to be installing EXT4 Recovery but its an APK and they are installed with the phone botted up normally correct? My phone isnt booting only in Recovery Mode which is the clockwork mod (from about 8 months ago)
4ext has an app to download its recovery. If you are s-off, the app will flash the recovery img.
Sent from my HTC Desire using Tapatalk
Ok I beleive I do have S-OFF from previous flashing however I can no longer boot the rom up so what do I do?
I can boot into recovery mode but as soon as I boot normally it just sits on the boot animation completly animated but never going further (left it for 3 hours until battery died) also tried wiping about 5 times after a wipe and I just cannot get it on. So what do I do?
I'll upload it for you (from my sd card).
If you are s-off, you can fastboot flash it (see link to my guides for info on fastboot flash - Forget adb, not relevant...)
Thanks but I am a little confused as to what I am doing.
Is there any step by step?
i have the 4EXT now not installed yet. What about HBOOT, radio rom I have no idea what I am doing in what order now due to my phone not botting :-(
If you don't have 4EXT recovery-reboot phone normally, install this app and update you're recovery from the list...
But if you read above I cannot boot my phone normally!
1.update the recovery(like i say)
2.change the hboot:downolad file PB99IMG.zip, put it on your sdcard, then start the phone in HBOOT mode (VolDown+POWER) to flash(update) the HBOOT.
3.Restart phone in recovery,perform full wipe(format all partition without FAT32)
4.Download file with ROM, put into your SDCARD and reflash...
I am sorry not having much luck. I have put both the EXT4 recoevry zip and the pb99img zip on my memory card rebooted into the boot loader with vol down went into the fastboot option and the only options there are bootloader (takes me back to main screen) reboot, reboot bootloader and power down.
I am so lsot and need my phone working again :-(
max_carpenter said:
But if you read above I cannot boot my phone normally!
Click to expand...
Click to collapse
If you'd bothered to read the fastboot faq I told you to read, you'd know that you fastboot flash from the fastboot screen NOT in Android!
max_carpenter said:
Irebooted into the boot loader with vol down went into the fastboot option and the only options there are bootloader (takes me back to main screen) reboot, reboot bootloader and power down.
Click to expand...
Click to collapse
Again, all in the FAQ you were supposed to read!!!
Sorry missed the link couldnt see one very tired. I appreciate your help. I am looking over it now trying to figure it out.
max_carpenter said:
Sorry missed the link couldnt see one very tired. I appreciate your help. I am looking over it now trying to figure it out.
Click to expand...
Click to collapse
OK good luck, although if you're tired, it may be better to wait until tomorrow. Its not broken so its just a case of remaining calm and doing the required.
Ok I think I got it phone is plugged in with the HBOOT drivers I h ave extracted that EXT4 zip you sent me to the C Drive and I run the following command:
fastboot flash recovery c:\recovery.img
Just wanted to check before I did it.
Hmm ok I have done something wrong :-(
sending 'recovery' (3730 KB)... FAILED (status malformed (1 bytes))
finished. total time: 0.004s
Ok I went into FASTBOOT on the phone screen then tried running the command again and I get this:
sending 'recovery' (3730 KB)... OKAY [ 0.676s]
writing 'recovery'... INFOsignature checking...
FAILED (remote: signature verify fail)
finished. total time: 1.197s
Are you sure you're s-off? Should say on the hboot screen
Sent from my HTC Desire using Tapatalk
Ahh its on damn I am sure it was off. Dont you have to be booted into a rom to get it off though?
Ok so who is clever enough to figure out the mess I am in now then..
1: Custom rom Won't boot even after wipe/several reboots
2: HBOOT Version = PVT1 0.93.0001
3: Radio Version = 5.09.05.30_2
4: Recovery Image is ClockworkMod v2.5.0.7
5: S-ON is set
6: Running the HTC Official RUU returns this error after a little while:
ERROR[140]: Bootloader version error
7: I have been asked to run the following commands with the following files and results are on each line after the = sign:
fastboot erase cache = OK
fastboot oem rebootruu = ... INFO[ERR] Command error !!!
fastboot flash zip C:\rom.zip = INFOsignature checking...
FAILED (remote: not allowed)
fastboot flash zip C:\PB99img.zip = FAILED (remote: signature verify fail)
rom.zip was extracted from the official HTC RUU utility.
Any ideas? At the moment i will be pleased jsut to get back to stock.

[Q] Flashed EU HOX with AT&T stuff and BRICKED! Please help

I'm desparate, please help me!
I flashed the remove-3-dot for the AT&T HOX, but I have another one. Now I cannot go back, since the device doesn't completely boot.
It is stuck with the HTC figures showing up and halfway the music stops and the device hangs.
I can go to recovery, but since the Àll-In-One Kit from Hasoon2000 doesn't see the device when in recovery (CWM 5.8.2.7 Touch), I cannot even put anything to the SD card, so I cannot even flash anything else!
Please help me before the battery dies out!! (I cannot turn it off since lonng press of the power button only restarts the booting)
If you have CWM did you made a nondroid backup?
Bright.Light said:
I'm desparate, please help me!
I flashed the remove-3-dot for the AT&T HOX, but I have another one. Now I cannot go back, since the device doesn't completely boot.
It is stuck with the HTC figures showing up and halfway the music stops and the device hangs.
I can go to recovery, but since the Àll-In-One Kit from Hasoon2000 doesn't see the device when in recovery (CWM 5.8.2.7 Touch), I cannot even put anything to the SD card, so I cannot even flash anything else!
Please help me before the battery dies out!! (I cannot turn it off since lonng press of the power button only restarts the booting)
Click to expand...
Click to collapse
THIS will help you
@muamers: Thanks!!
I already found out how to turn the device off, not draining the battery anymore.
I also flashed the new CWM 5.8.3.1 so it should have some ability to charge.
I am currently downloading the latest stock 1.29.401.11 and will try to flash that one.
I did search, but it's difficult currently. However, I made a permanent link to the Wiki - it's more than useful (the reason it exists, I know...)
Oh - it wasn't bricked (because it still did some stuff)
@jeyml: No, I did not do that (didn't know it was possible)
Does that mean that I could recover with the rom exactly as it was put on the device? (including installed ZIP files)
Bright.Light said:
@muamers: Thanks!!
I already found out how to turn the device off, not draining the battery anymore.
I also flashed the new CWM 5.8.3.1 so it should have some ability to charge.
I am currently downloading the latest stock 1.29.401.11 and will try to flash that one.
I did search, but it's difficult currently. However, I made a permanent link to the Wiki - it's more than useful (the reason it exists, I know...)
Oh - it wasn't bricked (because it still did some stuff)
@jeyml: No, I did not do that (didn't know it was possible)
Does that mean that I could recover with the rom exactly as it was put on the device? (including installed ZIP files)
Click to expand...
Click to collapse
Yup.It is actualy quite simple,i always do a backup before i flash something or update my ROM and other stuff.You keep the volume down + power button.After that you enter recovery mode (you will need to have CWM) and you have an option there "backup and restore",enter there and make a backup.Next time if you have any problems just enter again in the CWM,go to "backup and restore" and restore the backup you've made.It saves everything you have (i mean the ROM setting and such.Apps and other stuff must be backed up with Titanium Backup).
The backups you made are saved in the SD card in the nandroid directory if i remember corectly,so if you update you're ROM to...1.29 for example and have a 1.28 backup just enter there and delete it and make a new backup of the 1.29 so you don't get confused in so many backups and if you ever have problems and restore a 1.28 backup on you'r 1.29..well...you realize that the phone isn't going to work anymore.So,be carefoul.
Didn't work... I downloaded this rom: RUU_ENDEAVOR_U_ICS_40_HTC_Europe_1.29.401.11_Radio_1.1204.105.14_release_260491_signed
did everything this page told us: http://forum.xda-developers.com/showthread.php?t=1609190
But I do not see anything change... It's still stuck in the boot process.
I don't know what I am doing wrong...
I also didn't find a clear guide for how to do things - it's all pieces which everyone has to put together, making it hard when there is a real problem.
If this can be solved, I will investigate the nand backup for certain!
For now I need my phone, but it does not work...
Oh - how does the charging with the new clockwork work? I don't see anything happen, so I am afraid the battery will be down soon.
edit: It was on power all night and when I looked it had the screen on. Unplugging and replugging and the gren light went on. Does that mean the battery is filled?
One important fact: the adb command cannot find the device and I don't know why!
How did you flash the RUU? You have to connect the phone in FASTBOOT to the PC and then run it (with a locked bootloader) and it replaces the entire system
EddyOS said:
How did you flash the RUU? You have to connect the phone in FASTBOOT to the PC and then run it (with a locked bootloader) and it replaces the entire system
Click to expand...
Click to collapse
with a LOCKED bootloader?
Mine is unlocked...
I will try to relock the boorloader (saw somewhere a snippet)
Tried with a locked one:
Code:
D:\One_X_All-In-One_Kit_v1.0\Data>fastboot oem lock
... INFOLock successfully...
OKAY [ 0.143s]
finished. total time: 0.143s
D:\One_X_All-In-One_Kit_v1.0\Data>fastboot flash boot boot_signed.img
sending 'boot' (4288 KB)... OKAY [ 0.667s]
writing 'boot'... FAILED (remote: not allowed)
finished. total time: 0.874s
D:\One_X_All-In-One_Kit_v1.0\Data>fastboot flash system system.img
sending 'system' (963584 KB)... FAILED (remote: (00000008))
finished. total time: -0.000s
The bootloader loocks relocked ok (as it shows on top of that screen)
But flashing is impossible and, of cause, I don't know why
Adb will work in recovery but only if you boot the recovery from fastboot.
Fastboot boot recovery recovery.img
ok, next approach:
- Booted to fastboot
- unlocked bootloader with the unlock .bin file
- fastboot boot Recoveries\CWM5.8.3.1.img
- adb push rom.zip /sdcard/
- waited 5 minutes until done
- in recovery: Install zip from sdcard
- manual selected the rom.zip (yes, it was actually on the SDcard, so adb did its job)
- got an error that the image was bad:
ClockworkMod Recovery v5.8.3.1
-- Installing: /sdcard/rom.zip
Finding update package...
Opening update package...
E:Can't open /sdcard/rom.zip
I think I will have to get another image, right?
This one was extracted from
RUU_ENDEAVOR_U_ICS_40_HTC_Europe_1.29.401.11_Radio_1.1204.105.14_release_260491_signed.exe
I started the program and searched for the rom.zip in my temp folder. Was this ok?
Run .11 RUU, wait until load all completely, now go to %temp% in your pc and find a folder that contain a ROM.ZIP file... Unzip the files and flash the boot_signed.img and the recovery_signed.img, then relock your phone fastboot oem lock) do a factory reset (with the new recovery) and then try to run the .11 RUU.
THAT SHOULD WORK
pd: sorry for my poor english.
Sent from my HTC One X using XDA
Bright.Light said:
ok, next approach:
- Booted to fastboot
- unlocked bootloader with the unlock .bin file
- fastboot boot Recoveries\CWM5.8.3.1.img
- adb push rom.zip /sdcard/
- waited 5 minutes until done
- in recovery: Install zip from sdcard
- manual selected the rom.zip (yes, it was actually on the SDcard, so adb did its job)
- got an error that the image was bad:
ClockworkMod Recovery v5.8.3.1
-- Installing: /sdcard/rom.zip
Finding update package...
Opening update package...
E:Can't open /sdcard/rom.zip
I think I will have to get another image, right?
This one was extracted from
RUU_ENDEAVOR_U_ICS_40_HTC_Europe_1.29.401.11_Radio_1.1204.105.14_release_260491_signed.exe
I started the program and searched for the rom.zip in my temp folder. Was this ok?
Click to expand...
Click to collapse
You haven't a clue have you?
You don't flash an RUU from CWM, it's a Windows application!
1. Boot phone into FASTBOOT
2. Connect to the PC
3. Lock the bootloader
4. Run the RUU
Job done
@wolfraim: Yes, the factory reset was the one culprit, it seems!
EddyOS: Tried that so many times, but finally wolfraim added a crucial point: Factory reset!
Now the RUU install from the PC is working... (Have to wait for some time ...)
* I have to go for now, right after the flash is done.
When I've got the time, I will try to make some more notes and maybe another step-by-step story on how to make the device work again.
Thank you very much for your patience and help!
This is why I love the xda-developers site so much!
(and all possible ways included on XDA to brick my device is the reason why I hate xda sometimes... )
edit: Flashing has succeeded! Software number: 1.29.401.11, so it seems I also have the latest ROM update now.
I'll make a recovery backup asap and will try the titanium backup too.
Oh, this one is SU-locked of cause, so I will have to install the SU zip file again... Much work is to be done yet. Maybe I should look for a good ROM in the Android development area.

[Q] Help rooting Wildfire S please

Hi All
Spent most of today trying to root the good lady's phone, using http://forum.xda-developers.com/showthread.php?t=1195275Much more difficult than I thought! I have got as far as having unlocked the bootloader but when I try Flashing the Custom Recovery UI, I get "CID incorrect" Could someone please explain what this means. I have tried searching for help but not found anything i understand sufficiently to proceed. What is a goldcard and what does it do please?
It has just stuck me that I have the PG76IMG.zip file and the root.zip on the sd card at the same time, should it just be PG76IMG.zip until the CWM recovery UI is installed? Many thanks for your help it is much appreciated.
O
pompeyrodney said:
Hi All
Spent most of today trying to root the good lady's phone, using http://forum.xda-developers.com/showthread.php?t=1195275Much more difficult than I thought! I have got as far as having unlocked the bootloader but when I try Flashing the Custom Recovery UI, I get "CID incorrect" Could someone please explain what this means. I have tried searching for help but not found anything i understand sufficiently to proceed. What is a goldcard and what does it do please?
It has just stuck me that I have the PG76IMG.zip file and the root.zip on the sd card at the same time, should it just be PG76IMG.zip until the CWM recovery UI is installed? Many thanks for your help it is much appreciated.
Click to expand...
Click to collapse
There is already a post on this search around a bit more...wrong section too.
Don't forget to smash that thanks button down since its being a big meanie!
Harsh Response
Thanks for the response even if it was a tad harsh. I only posted as I could not find the answers i need so you sent me off searching again? I have been reading around and still do not know why the CID error occurred and still do not know if I am doing something wrong by having the PG76IMG.zip file and the root.zip on the sd card at the same time. I found a better way of obtaining the SD card CID using an android app called Gold Card helper and I now have a page http://psas.revskills.de/?q=goldcardwhere I can input the cid to get an image downloaded to me. What I still fail to see is why this has become necessary. Can you tell me if this card created during this process then has to be in the phone when I attempt to flash the clockwork mod recovery image, as that is on another sd card. Please enlighten me and I shall give deserved thanks.
pompeyrodney said:
Thanks for the response even if it was a tad harsh. I only posted as I could not find the answers i need so you sent me off searching again? I have been reading around and still do not know why the CID error occurred and still do not know if I am doing something wrong by having the PG76IMG.zip file and the root.zip on the sd card at the same time. I found a better way of obtaining the SD card CID using an android app called Gold Card helper and I now have a page http://psas.revskills.de/?q=goldcardwhere I can input the cid to get an image downloaded to me. What I still fail to see is why this has become necessary. Can you tell me if this card created during this process then has to be in the phone when I attempt to flash the clockwork mod recovery image, as that is on another sd card. Please enlighten me and I shall give deserved thanks.
Click to expand...
Click to collapse
Bro can you at least text format your posts?? You write everything in a single line without pressing enter.
It becomes creepy to read.
Anyways, Where is the prob?
Prob is in rooting or in flashing CWM(clockwork mod recover) ?
For CWM ,
http://www.clockworkmod.com/rommanager
find the device , and click on the version number to start downloading.. (its 5.0.8 as of now)
then paste it to desktop. And then with the fastboot command flash it to your mobile in fastboot mode.. you will be done. Then the root.zip that you have , flash it from recovery .
Hi Mihir
Thanks for your help, I had no idea there was a specific recovery image for each model of phone.
Now that I have downloaded the image can I substitute the image for the one I currently have and then I guess run
Code:
fastboot flash recovery recovery-clockwork-5.0.2.8-marvel.image
would that be correct as i guess the image need to be in the same directory as fastboot?
pompeyrodney said:
Thanks for your help, I had no idea there was a specific recovery image for each model of phone.
Now that I have downloaded the image can I substitute the image for the one I currently have and then I guess run
Code:
fastboot flash recovery recovery-clockwork-5.0.2.8-marvel.image
would that be correct as i guess the image need to be in the same directory as fastboot?
Click to expand...
Click to collapse
ya that would be correct
Code:
fastboot flash recovery recovery-clockwork-5.0.2.8-marvel.img
should be .img rather than .image...
Thanks Mihir I will try that when my battery has recovered!
Please help
Hi
I have just managed to download the correct Recovery image as suggested and it appears to have installed correctly.
Code:
c:\WFS>fastboot flash recovery recovery.img
sending 'recovery' (4494 KB)...
OKAY [ 1.700s]
writing 'recovery'...
OKAY [ 2.200s]
finished. total time: 3.900s
I have then removed the battery for a couple of minutes, restarted while holding down the volume minus.
I get the white screen showing hboot at the top highlighted in blue and fastboot highlighted in blue further down.
The sd card is then checked? and I can then select recovery and press the power button.
I then wait for the recovery options but all I am seeing is a white screen saying HTC followed by a black screen with all the four screen button lights on?
There is no mention of any recovery options at all.
Has something gone horribly wrong?
Delete the old download, download the recovery again, and flash it using a GOOD USB-cable. preferably the shortest and sturdiet you have. The image file has probably been corrupted somewhere from the interwebs to your computer, or from your computer to your phone.
Success at last
I finally got Recovery to work with the help of the Recovery provided by Operator3 at this thread http://forum.xda-developers.com/showthread.php?t=1997465&page=3
I used Recovery to install the root.zip and I now finally have a rooted phone, woo hoo!!:laugh:
Now all I need to do is free up some space at last.

[Q] HTC Desire Bravo PVT1 badly bricked. Unrooted and S-ON

Hi everybody, first of all many thanks for a great forum. I have found it very useful in the past and never needed to seek help, but this time I am stumped and although I read pretty well all the threads on the subject I have not been able to solve my problem and I fear I have a paper weight on my hands.
My Desire does not boot up and stays on the HTC logo on a white screen for ever. This happened after a stupid and unresearched attempt to downgrade my Hboot from 1.03 to earlier ones with RUU_Bravo_H3G_UK_1.20.771.3_Radio_32.36.00.28U_4.06.00.02_2_release_124822.exe.
The process worked fine but my Desire never managed to reboot and got stuck on the opening logo.
I can go into HBOOT USB PLUG and I can charge the battery (the led comes on and eventually goes green). The HBoot screen reads:
LOCKED (00W)
BRAVO PVT1 SHIP S-ON
HBOOT - 1.03.0003
TOUCH PANEL - SYNT0101
RADIO - 4.05.00.11
Date 21 2011 - 20:44:09
I can do FASTBOOT DEVICES and get
HT06XPL00452 fastboot
but any other operation with fastboot always gives me:
FAILED (status malformed (1 bytes)
Does anybody know what this means?
I also tried:
** to rerun the official RUU but I get a clearly wrong message saying that the battery is below 30% charge and the program stops.
** several other RUUs with same result except RUU_Bravo_Froyo_HTC_WWE_2_29_405_5_Radio_32_49_00_32U_5_11_05_27_release_159811_signed.exe which leads to ERROR [170]: USB CONNECTION ERROR. I know the USB Hboot drivers are ok and are those I downloaded from XDA. Device manager shows "Android composire interface"
** select RECOVERY but it goes immediately into the white screen aith HTC logo and gets stuck
** select CLEAN STORAGE . When I answer "Yes to Delete all user data?" it confirms "clear..." and then gets stuck on the log screen
** select SIMLOCK and get
FAT32 init OK
Open MCCMNC file fail
Open CID file fail
Has anybody got any other ideas? Should I just give up and use it as paperweight?
Tried the 2.3.3 WWW RUU? Download it from shippedroms
research and use the PB88IMG.zip method, bortak's troubleshooting guide.
eddiehk6 said:
Tried the 2.3.3 WWW RUU? Download it from shippedroms
research and use the PB88IMG.zip method, bortak's troubleshooting guide.
Click to expand...
Click to collapse
Many thanks eddiehk. The RUUs I had tried before came from shippedroms.com too but I cannot find any for the Desire (nor for the Bravo) with 2.3.3 nor WWW in their name. Do you have a specific link? I have just tried yet another one for luck but got the same result as before "battery less then 30%" which is not!:crying:
The PB88IMG.zip method cannot work for me as I cannot get to write to the system nor the sdcard as the phone does not boot up. I have read a bortak's guide, but it seem to be only for S-OFF setups and it also seems to be only for rooted phones. Mine is not rooted and it has S-ON.
Any other ides anybody?
marco_bruzzone said:
Many thanks eddiehk. The RUUs I had tried before came from shippedroms.com too but I cannot find any for the Desire (nor for the Bravo) with 2.3.3 nor WWW in their name. Do you have a specific link? I have just tried yet another one for luck but got the same result as before "battery less then 30%" which is not!:crying:
The PB88IMG.zip method cannot work for me as I cannot get to write to the system nor the sdcard as the phone does not boot up. I have read a bortak's guide, but it seem to be only for S-OFF setups and it also seems to be only for rooted phones. Mine is not rooted and it has S-ON.
Any other ides anybody?
Click to expand...
Click to collapse
http://shipped-roms.com/index.php?category=android&model=Bravo
"HTC_Desire_Android_2.3_Upgrade.zip" at the bottom
I meant "PB99IMG.zip" method sorry. It should and will work. It does not require the phone to be booted up. It only requires you to copy it to the root of the sdcard (use a card reader). Then boot into bootloader (volume down + power), wait a few seconds, then accept. All in the guide
Or search how to downgrade hboot 1.03 in these forums, I've seen it successfully done on a few occasions.
eddiehk6 said:
"HTC_Desire_Android_2.3_Upgrade.zip" at the bottom
I meant "PB99IMG.zip" method sorry. It should and will work. It does not require the phone to be booted up. It only requires you to copy it to the root of the sdcard (use a card reader). Then boot into bootloader (volume down + power), wait a few seconds, then accept. All in the guide
Or search how to downgrade hboot 1.03 in these forums, I've seen it successfully done on a few occasions.
Click to expand...
Click to collapse
Many thanks again. Unfortunately I got no further. I downloaded the PB99IMG_Bravo_Froyo_HTCCN_CHS_CU_2.35.1402.5_Radio_32.54.00.32U_5.14.05.17_release_163341_signed.zip file from the url you indicated. There were several PB99IMG... and picked one at random. None had the same radio as what was indicated on my Hboot screen by the way. Anyway given the lack of success I suspect it wouldn't have made any difference which one I picked. I then copied it to the root of the sd card using my PC and kept my fingers firmly crossed when I went into bootloader. After a brief moment I saw a subliminal message about checking something but could not read the rest. It then went back to the now very boring Hboot screen with the normal commands "fastboot;recovery;clear storage and simlock".:crying:
Then I tried to use the Universal Android AIO flasher and could see some messages. Trying to flash something in fastboot mode always gave this message:
"(bootloader) signature checking...
FAILED (remote: signature verify fail)"
It does look like something is very screwed up on the internal card and might need a total reformatting. Is it possible or am I barking at the wrong tree?
LATEST UPDATE
OK, I am officially an idiot.
The reason why the .zip file did not work was that I had not changed its name to PB99IMG.ZIP. I did that and hey presto got it to reload the firmware,
As I ended up with a Chinese carrier version I would now like to change it again to a European version preferably a no carrier version. How can I find out which version to pick and which one is the latest version on the ShippedRom site?
In the meantime many many many thanks for all the help. It is so great to have this forum to help all the newbies like me.
@marco_bruzzone
You got a Chinese ROM version because you ignored my advice......
You get the "European version preferably no carrier version" by actually reading my previous post..................
I even quoted the name and location of the correct RUU to use..............
eddiehk6 said:
@marco_bruzzone
You got a Chinese ROM version because you ignored my advice......
You get the "European version preferably no carrier version" by actually reading my previous post..................
I even quoted the name and location of the correct RUU to use..............
Click to expand...
Click to collapse
I am sorry for being dim, I reread your earlier posting and finally understood it. I will now try the correct .zip file. Thanks again

Categories

Resources