Ive just rooted, installed the lastest radio and installed the latest CM 6.1.1
After i rebooted phone it is now stuck in bootloop
Help?
Desire SLCD On telus if that matters.
Oh and i cant go back into Recovery. I can go into Hboot
check your reply on android forums
Restore the nandroid you made before flashing, or do a full wipe (in clockworkmod: data/factoryreset, cache and dalvik cache under advanced) and reflash the rom.
Hey Everyone,
I had Starburst with Data2SD flashed on my Desire with some things cooked in from the UOT. I found the MIUI ROM and I figured I wanted to try it. I made a Recovery backup so that if I didn't like it, I could get right back to where I left off. I flashed the CDMA MIUI ROM which was a mistake because my Desire is GSM (Doh) But I went in to recovery and selected the backup I made before I flashed MIUI and restored it, it restored successfully but when I reboot it just sits at the white screen that says htc and it doesn't go anywhere after that. I can reflash the Starburst ROM and reinstall the Data2SD and it will boot and everything and then I go back in to recovery and restore just the data from the back up and it doesn't boot after that. Can anyone help me figure out where I'm going wrong? I don't really want to start from scratch. Any help is appreciated. If you think you can help but don't understand what I'm asking, either post here or PM me. Thanks. I would really like my Desire to work so I can stop using my dreaded Iphone.
Did you do a full wipe before you restored your backup? Make sure you do a factory reset/data wipe, cache wipe and dalvik wipe (from advanced menu)
If it still does not work, try wipe just the cache and dalvik cache after restoring the backup and see if it will boot then.
Yesterday I tried installing Danvh's 4.4.2 Google Edition ROM and I guess it must have went wrong. I backed up my current ROM and data before the installation. I did a full wipe (davick / data / cache etc.) and I also did a format of internal SD. I installed Danvh's ROM fine but when I rebooted after the installation it will not get past Galaxy S4 screen. So I figured there was something wrong with the ROM so I flashed back to my back up but when I restart my phone it will still be stuck at the S4 screen so I have to keep flashing back to the backup file. I used TWRP 2.6.1.0 for recovery and I also fixed the permissions with TWRP. Any ideas? What should I do? If my phone ever crashes I will have to restore to my only back up.
re: stuck
ragingazn628 said:
Yesterday I tried installing Danvh's 4.4.2 Google Edition ROM and I guess it must have went wrong. I backed up my current ROM and data before the installation. I did a full wipe (davick / data / cache etc.) and I also did a format of internal SD. I installed Danvh's ROM fine but when I rebooted after the installation it will not get past Galaxy S4 screen. So I figured there was something wrong with the ROM so I flashed back to my back up but when I restart my phone it will still be stuck at the S4 screen so I have to keep flashing back to the backup file. I used TWRP 2.6.1.0 for recovery and I also fixed the permissions with TWRP. Any ideas? What should I do? If my phone ever crashes I will have to restore to my only back up.
Click to expand...
Click to collapse
You forgot to do a "factory reset" in twrp before restoring your Nandroid backup.
Most likely after doing that the phone will fully boot.
Be sure to wipe data, system, cache, dalvik cache and
do a factory reset before restoring your backup.
Good luck!
Good luck!
Nope I did do factory reset as well...
Hi all, hoping this is a stupidly simple fix. I wanted to update to latest stable CM7 and so downloaded and flashed it from CWRecovery,
I also ran the factory reset, and cleared the cache.
When I boot, it shows the blue loading screen, then comes to the "Welcome to ADR6300" and reverts to the CyanogenMod7 loading screen..
Then, it keeps bouncing back and forth between these two screens until I pull the battery...
You didn't mention the order of what you did. Assuming you have no valuable data, I would just start over.
Reboot into recovery
Wipe system
Factory reset
Flash ROM
Flash GAPPs (if desired)
Reboot into ROM
Also, ensure you're on the latest CWM, first.
[Solved]
PonsAsinorem said:
You didn't mention the order of what you did. Assuming you have no valuable data, I would just start over.
Reboot into recovery
Wipe system
Factory reset
Flash ROM
Flash GAPPs (if desired)
Reboot into ROM
Also, ensure you're on the latest CWM, first.
Click to expand...
Click to collapse
Worked perfectly! Thank you!!
Apparently the problem was having the wrong version of GAPPs. I was reinstalling but Wiping system was the step I had skipped!
Hello everyone,
This is what is happening to me. I was trying to flash Miroslav's Cyanogenmod 11 RC2 with Philz Touch 6.07.9, but none of the recomended methods worked for me, I just got stuck on lg logo bootloop - I really want this rom but it is hard as f**k to flash -. So I tried to go back to CM 10.2.1 and got the "Status 7" error. Very frustrated, I finally used my stock recovery image and it worked fine.
From this point, i was recovering my apps and data using titanium back up and when it finished, a notification asked if I wanted the official system update. I refused it and proceded to reboot. Now the phone boots instantly to recovery mode and show the purple screen of Philz touch. First I wiped cache and dalvik and got the same bootloop. Then I wiped cache, dalvik and factory reset and got the same bootloop. Finally, I formated system, factory reset, wiped cache, wiped dalvik and flashed again my recovery image, and got again the recovery mode bootloop.
Any Ideas? Thank you for your help.
Best regards.
EDIT: I must clarify that when I flash my recovery image, it ALWAYS get suck on a part that says something like "installing android security". I have to press power button 10 seconds to restart but it boots normaly in the stock rom.
chortiman said:
Hello everyone,
This is what is happening to me. I was trying to flash Miroslav's Cyanogenmod 11 RC2 with Philz Touch 6.07.9, but none of the recomended methods worked for me, I just got stuck on lg logo bootloop - I really want this rom but it is hard as f**k to flash -. So I tried to go back to CM 10.2.1 and got the "Status 7" error. Very frustrated, I finally used my stock recovery image and it worked fine.
From this point, i was recovering my apps and data using titanium back up and when it finished, a notification asked if I wanted the official system update. I refused it and proceded to reboot. Now the phone boots instantly to recovery mode and show the purple screen of Philz touch. First I wiped cache and dalvik and got the same bootloop. Then I wiped cache, dalvik and factory reset and got the same bootloop. Finally, I formated system, factory reset, wiped cache, wiped dalvik and flashed again my recovery image, and got again the recovery mode bootloop.
Any Ideas? Thank you for your help.
Best regards.
EDIT: I must clarify that when I flash my recovery image, it ALWAYS get suck on a part that says something like "installing android security". I have to press power button 10 seconds to restart but it boots normaly in the stock rom.
Click to expand...
Click to collapse
When in vain , unbrick your phone again using unbricking guide and use CWM , not all guide is working for the same type of phone . No need to wipe system clean cache watevr **** you were told unless recommended by developer and just factory reset then flash the rom
Mr.201 said:
When in vain , unbrick your phone again using unbricking guide and use CWM , not all guide is working for the same type of phone . No need to wipe system clean cache watevr **** you were told unless recommended by developer and just factory reset then flash the rom
Click to expand...
Click to collapse
Thanks for the answer and the advice about factory reset. Yes, I had to unbrick my phone and by the way, still could not install miroslav's cm11 RC3 using Philz touch 6.19.3.
But I have another issue: I successfully got back to CM 10.2.1 but after I restored my apps using Titanium Backup, I rebooted the phone and got stuck on CM logo for half hour. I wiped dalvik and got the same result. Then wiped cache and dalvik and still stuck. What should I do? Flash again the rom? The restored data is from CM 10.2.1 so I don't see any problem....
chortiman said:
Thanks for the answer and the advice about factory reset. Yes, I had to unbrick my phone and by the way, still could not install miroslav's cm11 RC3 using Philz touch 6.19.3.
But I have another issue: I successfully got back to CM 10.2.1 but after I restored my apps using Titanium Backup, I rebooted the phone and got stuck on CM logo for half hour. I wiped dalvik and got the same result. Then wiped cache and dalvik and still stuck. What should I do? Flash again the rom? The restored data is from CM 10.2.1 so I don't see any problem....
Click to expand...
Click to collapse
check again what you restore, user apps will have no problem to restore but system apps will cause incompatibility to the rom and crash it
Mr.201 said:
check again what you restore, user apps will have no problem to restore but system apps will cause incompatibility to the rom and crash it
Click to expand...
Click to collapse
The phone is good now, I restored the stock rom and from there I flashed CM 10.2.1 just making a factory reset. Plus I flashed adreno drivers and gapps. Once it booted, I restored my apps without sistem data and now the phone works properly.
Thank you Mr.201
chortiman said:
The phone is good now, I restored the stock rom and from there I flashed CM 10.2.1 just making a factory reset. Plus I flashed adreno drivers and gapps. Once it booted, I restored my apps without sistem data and now the phone works properly.
Thank you Mr.201
Click to expand...
Click to collapse
Glad it worked, make sure you untick 'system' in filter in titanium backup so that you can only see your user apps .