Related
I was trying to do the radio s off with visionary and something went wrong.
I downloaded visionary+ onto my Telus HTC Desire HD no problem, I had rooted it earlier and beleived that to be done correctly. I was getting ready to flash my radio and was going through the steps to do so when my problems began.
Now, all that happens is VISIONary+ keeps on rebooting. I have tried pulling the battery, I have tried to change my settings (re: usb debugging) but nothing seems to help.....all it does is continously shut back off and try to reboot.
Any help would be greatly appreciated.
Update: This issue has been resolved. I am now trying to figure out if my phone is properly rooted...go to page 2 in thread please
What is your build number in settings>about>software information? Anything higher (and including) than 1.7 will cause Visionary to fail. Then you have to downgrade first.
OK, that is my first mistake, my Build # is 1.84.61.2.
I will attempt the downgrade and report back here
I am at the downgrade prompt. When I put in the command "adb push psneuter /data/local/tmp" I get a message saying "'adb' is not recognized as an internal or external command, operable program or batch file"
What did I do wrong?
bleagues said:
I am at the downgrade prompt. When I put in the command "adb push psneuter /data/local/tmp" I get a message saying "'adb' is not recognized as an internal or external command, operable program or batch file"
What did I do wrong?
Click to expand...
Click to collapse
download android sdk first
http://developer.android.com/sdk/index.html
put your command to the folder .. for example if u extract to desktop with folder android, then go to command prompt, point to the folder first
e.g: "cd desktop" "cd android"
p/s: put the file inside the folder too
Thanks Hayday, this dosen't seem to help though.
I have the Android SDK in my C: drive and I have placed the "downgrade" folder inside of it. And I still get the same error of "adb' is not recognized as an internal or external command, operable program or batch file" when I type the "adb push psneuter /data/local/tmp"
Any other suggestions?
I believe it still may be a driver problem. I keep getting a message from HTC Sync that says "HTC sync port of ### is not responding. Please disconnect cable and reconnect after 10 seconds"
Can I use the program terminal emulator to do this directly on the phone?
does the folder have adb.exe in it ?
if you place the android sdk folder in c for example the folder name is "android" , you just go to cmd .. then type "cd c:/android/"
and then type "adb" ..
you must use the command inside c:/android .. not c:/android/Downgrade
to be safe, just copy everything in "Downgrade" folder and paste to android sdk folder too ..
btw, here is the full thread by jkoljo himself on how to downgrade.
http://forum.xda-developers.com/showthread.php?t=905003&highlight=downgrade
I have done exactly as you say, I have the "downgrade" folder inside of the "AndroidSDK" folder....and still get the exact same message of "'adb' is not recognized....."
I cannot post a question in that other thread because I have fewer than 10 posts. I will as soon as I get up to 10.
Download & install htc sync, this should include all the drivers you need.
I think you need net framework 3.xx installed as well.
Then in cmd, go to where you put the downgrade file (cd blah blah) - http://forum.xda-developers.com/attachment.php?attachmentid=483902&d=1294492245 - & then the command lines should work.
arlrb said:
Download & install htc sync, this should include all the drivers you need.
I think you need net framework 3.xx installed as well.
Then in cmd, go to where you put the downgrade file (cd blah blah) - http://forum.xda-developers.com/attachment.php?attachmentid=483902&d=1294492245 - & then the command lines should work.
Click to expand...
Click to collapse
oh forgot to mention. download and install htc sync for the driver.
http://www.htc.com/www/supportdownloadlist.aspx?p_id=324&act=sd&cat=all
bleagues said:
I have done exactly as you say, I have the "downgrade" folder inside of the "AndroidSDK" folder....and still get the exact same message of "'adb' is not recognized....."
Click to expand...
Click to collapse
adb.exe is found in platform-tools folder in the android-sdk folder.
Add it to your path. Eg: PATH=c:\android-sdk\platform-tools;%PATH%
Thanks arjunr, after a little bit of tinkering with some files and folders I got it!
Thanks!
Now that I have the proper build #, I want to make sure my phone is properly rooted......or do I have to re-root it?
Is there any way to check and see if my phone is properly rooted?
I had rooted it before I did the build downgrade, does this make a difference?
My phone out of the box was a HTC Desire HD by Telus. The rooting that I followed was the http://forum.xda-developers.com/showthread.php?t=954997"which is the "[GUIDE] Telus Desire HD - Rooting and Flashing" found here on this website
I am good to go, I am rooted and downgraded!
bleagues said:
I am good to go, I am rooted and downgraded!
Click to expand...
Click to collapse
yeah now you can proceed with s-off, and flash new roms if you like.
Heydayat, I seem to be having some issues with anything internet related. I have started another post at http://forum.xda-developers.com/showthread.php?t=1012754 can you take a look at this and see if you can help me?
Thanks
Update: I have fixed the issue at the other thread, it was my APN settings.
Thanks to all for the help
Hi Guys, sorry if this has been posted before but i have just spent 14 hours trying to un usb-brick my desire. Each method seemed to need root which i had lost.
Eventually i found these instructions, they are not mine, i only found them so total kudos to the author. to keep it simple (and remember this is for unrooted desires:
Requirements:
Fastboot (part of Android SDK) installed. For instructions on setting up fastboot, search guide on how to install ADB & Android SDK.
HTC Desire USB Unbrick Files .
Android Terminal Emulator app (Install from Android Market)
Procedure:
Reboot your device into its bootloader (fastboot) mode and connect it to your computer via USB.
Launch a Command Prompt window on your computer and enter this command:
fastboot oem enableqxdm 0
On your phone, Go to Menu > Settings > About phone > Software information and note down the Kernel version that you see there. If you see more than just numbers, only note down the numbers e.g. 2.6.32.15.
In the Command Prompt window on your computer, enter this command:
fastboot getvar cid
Note down the CID that you get. It should be something similar to ‘HTC__022’.
Visit this site, enter the CID from step 4 and the kernel version from step 3 as the ROM version, and click ‘OK’. This will generate an mtd0.img file and prompt you to download it. Save it somewhere you will remember.
Now connect your SD card to your computer using a card reader device or another phone, and transfer the extracted HTC Desire USB Unbrick files as well as this mtd0.img to it. Make sure the files are in the root of the SD card and not in any folder.
Insert the SD card back into your phone.
Launch Terminal Emulator on your phone and enter these commands:
cat /sdcard/rageagainstthecage-arm5.bin > /data/data/jackpal.androidterm/rageagainstthecage-arm5.bin
cat /sdcard/flash_image > /data/data/jackpal.androidterm/flash_image
cat /sdcard/mtd0.img > /data/data/jackpal.androidterm/mtd0.img
cd /data/data/jackpal.androidterm/
chmod 755 rageagainstthecage-arm5.bin flash_image
/data/data/jackpal.androidterm/rageagainstthecage-arm5.bin
In case your phone seems to crash or shows erratic behavior, ignore it for now.
Completely quit Terminal Emulator: First press the ‘Home’ button and then go to Menu > Settings > Applications > Manage Applications > All, find ‘Terminal Emulator’ there and tap ‘Force Stop’.
Launch Terminal Emulator again. This time, you should see a # prompt instead of $, indicating you have achieved temporary root access necessary for the next step.
Enter these commands in Terminal Emulator:
cd /data/data/jackpal.androidterm/
./flash_image misc mtd0.img
Finally, reboot your phone and you’re done.
That’s all there is to it – your USB brick issue should now be fixed.
If Mods believe this is easily accessible elsewhere on XDA, please delete the post but it took me 14 hours of trawling the net to get my desire un-bricked
regards
Whilst the info is good it's quite useless without the actual links. I'm sure I've seen similar info within these forums before though. Fortunately I've not managed to brick mine (yet).
Parva4 said:
Whilst the info is good it's quite useless without the actual links. I'm sure I've seen similar info within these forums before though. Fortunately I've not managed to brick mine (yet).
Click to expand...
Click to collapse
Sorry about that, files now added to first post
Regards
Jamadant
Try to get visionary+ I don't think you can get it from the market but there are other places, this will give you temporary root as I couldn't get root using the rageagainstthecage, then extract the flash image and paste it with the mtd file in data, then carry on with the commands in as above after the root (so dnt enter commands for rageagainstthecage as that is a process for getting root)
If you need more details let me know as I know how it feels to almost have a very expensive paperweight
Sent from my HTC Desire using XDA Premium App
thanks for you to share this method
USB Brick HELP!
Hi, last night I got my htc desire bricked. Pc can't detect my phone and sd card.
As a requirement on your posted guide, i need to install ADB and Android SDK. But when I plugged my phone into my pc to install software drivers its showing "Qualcomm CDMA Technologies MSM Driver not found". Where can I get this drivers?
I tried also to enable SD card by "fastboot oem enableqxdm 0' in command prompt but "'fastboot' is not recognized as an internal or external command"
My phone details for reference:
Android 2.2
Hboot 0.93
Software 2.14.207.1
PVT3 Ship S-On
RAdio 5.09.05.30_2
Unrooted, O2 branded
How can I continue to unbrick my phone with these initial problems?? Can you suggest newer guide for my case?
PLEASE HELP!
USB Brick help...
after i force stop the terminal emulator when i try to lounch it again doesn't run.
i get a white screen and nothing more
have you guys any ideea why is this happening?
rugarai_3x said:
Hi, last night I got my htc desire bricked. Pc can't detect my phone and sd card.
As a requirement on your posted guide, i need to install ADB and Android SDK. But when I plugged my phone into my pc to install software drivers its showing "Qualcomm CDMA Technologies MSM Driver not found". Where can I get this drivers?
I tried also to enable SD card by "fastboot oem enableqxdm 0' in command prompt but "'fastboot' is not recognized as an internal or external command"
How can I continue to unbrick my phone with these initial problems?? Can you suggest newer guide for my case?
PLEASE HELP!
Click to expand...
Click to collapse
Follow my instructions here for fastboot :- http://forum.xda-developers.com/showthread.php?t=1176663
HBoot 1.02 S-On No Root
Hi!
I USB-Bricked my Desire PVT4. Now it is with HBoot 1.02 and official unrooted Gingerbread.
I tried common methods, but I cant get access to write misc partition.
I got my SD card working with fastboot oem enableqxdm 0. I made a valid mtd0 Image etc... but after copy the flash_image, rageagainstthecage and mtd0 the terminal emulator wont run after stopping the task.
Cant downgrade HBoot without root. Alpharev (revolutionary4-4) needs USB running in ROM.
Please !!!! I need help!!!!!
Thanx guys
Search for guide for usb brick.
TouchPaled from Oxygen with Transparent XDA App
MatDrOiD said:
Search for guide for usb brick.
TouchPaled from Oxygen with Transparent XDA App
Click to expand...
Click to collapse
I did (with help of Leinad):
http://forum.xda-developers.com/showthread.php?t=955845
Cant pass step 5! Relaunching the Terminal Emulator fails! Doesnt open anymore. I read, that writing Misc partition in HBoot 1.02 is not possible using this method.
Need working method for HBoot 1.02 with official gingerbread 2.3.3 in order to USB-unbrick my Desire!
Any ideas?
dexterm1 said:
I did (with help of Leinad):
http://forum.xda-developers.com/showthread.php?t=955845
Relaunching the Terminal Emulator fails!
Click to expand...
Click to collapse
Try to re-do all the steps..if it fails to open, before u can flash the misc partition, maybe u did something wrong..at least it should open and u should be able to run the commands to flash the misc
hey guys,
i am new to xda and i need your help please.....i did the OTA update few days back and downloaded the visionary+ but the visionary gets stuck on the black screen and nothin happens and i also downloaded the gingerbreak v1 it gives a error of could not extract assets error, i read everything regarding this error but nothing help can you please help me on who can i do a S-off and enter the recovery mode and install the rom on the OTA 2.3.3 in desire HD......i dnt know how to use adb commands (i dnt have SDK).....please help me
I don't think there's a root option available for that firmware. You will likely have to make a gold card, temp root, downgrade, then perm root it. It's really not hard, and you will just need to copy/paste commands found in instructions. Just be sure to read the instructions through completely one or 2 times first, and then follow them well.
But you can boot up normally right? Try this http://forum.xda-developers.com/showthread.php?t=1152233
Sent from my HTC Desire HD using XDA App
i read the post, also downloaded the downgrade and ran "run thi for root" but a CMD prompt opened up and it closed automatically after few secs.....and i dnt know hat is adb and adb sheel and how to use it....i tried typing the adb code in the CMD prompt but gave me an error message saying something internal or external........i also tried using gingerbreak but giving me an error message of something extract assets.......please help ppl
It means that you've fail to execute step 3 in the guide right? Then use adb process. It refers to use direct command from android software developing kit. Download the android sdk tool from http://developer.android.com/sdk/index.html (recommended to use web installer, Java runtime required)
Usually it will create sdk folder in C:/ local disk. In the folder, shift+right click tools folder and click command prompt. Enter the command lines in the guide and continue.
You can't use gingerbreak on android build above 2.37. As I assume that you have applied OTA with at least 2.42. Is that correct?
Sent from my HTC Desire HD using XDA App
ya i have a 2.42 after the OTA........i think its the third step, i have the android sdk but i dnt know how to use it, i need the sense3.0 rom desperately....hope you can help me with the sdk thing
http://driphter.com/index.php?topic=3867.0
Instead of Goldcard Helper when making your goldcard...
- Open up a command prompt (Windows Key + R, type "CMD", press enter)
- connect your phone as "charge only" and have usb debugging enabled
- type: cd "c:\htc ace toolkit\resource" and hit enter (if you've already extracted my toolkit)
- Now type:
adb shell cat /sys/class/mmc_host/mmc2/mmc2:*/cid
-Select and copy the cid, then paste into the appropriate field on the Goldcard Generator webpage.
You will now get a proper image, that once applied, will give you a proper working Goldcard to copy the PD98IMG.zip to and downgrade your device. and can now start with the fre3vo downgrade.
cant open your tool kit some kind of error.....
vaibhav_ertx said:
cant open your tool kit some kind of error.....
Click to expand...
Click to collapse
if you're using IE 9, read what it says underneath the toolkit download link.
If you're using avg it will flag it as some type of bad software (its cuz avg sucks long donkey......)
when i type adb in cmd it gives me error something internal and external thing it says help ppl
vaibhav_ertx said:
when i type adb in cmd it gives me error something internal and external thing it says help ppl
Click to expand...
Click to collapse
1. do you have the phone connected to your pc with usb debugging enabled?
2. Do you have HTC Sync installed (for the drivers)?
JSLEnterprises said:
1. do you have the phone connected to your pc with usb debugging enabled?
2. Do you have HTC Sync installed (for the drivers)?
Click to expand...
Click to collapse
i have done the debugging but not installed the htc sync software
JSLEnterprises said:
if you're using IE 9, read what it says underneath the toolkit download link.
If you're using avg it will flag it as some type of bad software (its cuz avg sucks long donkey......)
Click to expand...
Click to collapse
i use safari not ie9 and i dnt have avg i have kaspersky
JSLEnterprises said:
http://driphter.com/index.php?topic=3867.0
Instead of Goldcard Helper when making your goldcard...
- Open up a command prompt (Windows Key + R, type "CMD", press enter)
- connect your phone as "charge only" and have usb debugging enabled
- type: cd "c:\htc ace toolkit\resource" and hit enter (if you've already extracted my toolkit)
- Now type:
adb shell cat /sys/class/mmc_host/mmc2/mmc2:*/cid
-Select and copy the cid, then paste into the appropriate field on the Goldcard Generator webpage.
You will now get a proper image, that once applied, will give you a proper working Goldcard to copy the PD98IMG.zip to and downgrade your device. and can now start with the fre3vo downgrade.
Click to expand...
Click to collapse
hey, i downloaded your toll kit by using, IE9,firefox,safari but when i try tp unzip i get an error message "cannot open the file does not appear to be valid"
help
Good Morning to everyone (Germany ).
I´ve downgraded my DZ from the actual version to Froyo. Now i want to root it. I was searching for different manuals and all of them said that it´s necessary to check the Infocid. Unfortunately it doesn´t really work on my phone.
http://forum.xda-developers.com/showthread.php?t=905261
The first step seems to be clear. I type in the command and the phone restarts and powers up in the boot menu. But when I type in the second command line, the terminal says that this command was not found. Every files should be in the right folder i think, but it does not work. Do you have any ideas, what the problem might be? I don´t have i file called fastboot oem loader in my platform-tools-folder. Is that the problem?
Thank you very much.
Edit: Now i also found this Thread. http://forum.xda-developers.com/showthread.php?t=1140722 . But what does "set up on your computer" mean? Is it a programm? I got a fastboot folder in my platform-tools with 3 fastboot files for each OS. So: Do i have to rename the fastboot-mac to fastboot? Lot of questions, don´t want to brick it
...so you already downgraded succesfully to 1.34 wwe?
then i would use this guide for perm root:
http://forum.xda-developers.com/wik...sion#Rooting_the_Vision_.28G2.2FDZ.29_and_DHD
...if you get in troubles pm me
Solved, had to rename the command line to reboot-mac
Hello.
I wanted to root my htc one x and got to the step when i enter/get the token, but i cant seem to go further than step 8 when i get the bootloader token in cmd, it just says that cd \Android is not a valid path or something, so i cannot unlock the bootloader.
Please help me out here.
please give me the exact error message you get... i rooted mine 2 days ago (but with the normal root method without this program).
Sounds like a Folder error or something. Where have you placed the toolkit ??
Dont know if there is an error, but when i try to unlock bootloader from cmd with cd \Android i get that the path is invalid.
The toolkit is placed for me in D: drive in an "Htc one x root" folder.
And i dont even have a path to an android folder in c drive.
And how do i even get the right android folder in the c drive?
Sorry for this "noob'ish" questions, but all the rooting i have done before was through superoneclick and "on-phone" rooting.
Ok a few things. Where did you save your SDK to? If its in c:/program files move it to root. You can do this all easily in Windows explorer. Then go to cmd, type in "cd..", enter, then "cd..", again. you should be in root. Then type dir and check if android is there. Try to "cd android", enter, "cd platform-tools" type dir and you should see adb and fastboot, then do fastboot OEM unlock. For me I added the android folder to my environment variables so I can do adb from any folder, so I don't need to put everything on my android folder! Pm me if you need more help. I'm also willing to help over remote desktop. It took me so long to set up the SDK so I know how irritating it feels.
Sent from my HTC One X using XDA
the sdk is located in c:/program files(86)/Android/Android-SDK
andsa said:
the sdk is located in c:/program files(86)/Android/Android-SDK
Click to expand...
Click to collapse
try cd \program file (x86)\android\android-sdk\platform-tools
Still the same message.
sorry for late answer but i cant send you a mail... it seems you disabled it in your setting so I post it here:
I do it with the following method and it worked like a charm:
LINK
if you still "stuck" on your method, give this a try... its not complicated
I managed to root the phone