Related
EDIT: OP EDITED WITH CHANGED PTA SETTINGS UNDER APN TYPE!
After reviewing the GS2 thread on the same topic (http://forum.xda-developers.com/showthread.php?t=1109983), I thought it might be worthwhile to discuss this issue on the Nexus. I was not able to get the Nexus connected using the information in that thread. However, I was able to get it connected to pta using a slightly modified version of the Skyrocket settings, which I'll post below.
One quick question before I do that, though -- I am only able to get 3 mb/s or so on my Nexus. I am on the unlimited data SOC code for LTE: LDPPVM5 -- think that code is causing any problems?
Anyway, here are working settings to get to PTA (the one the Skyrocket uses):
1) Go to settings, more (under networks), Access Point Names
2) Click on the 3 dots to create a new APN, name it AT&T PTA, and enter the following:
Name: ATT pta
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMS Proxy: not set
MMS port: not set
MCC: 310
MNC: 410
Authentication type: not set
APN type: default,internet,supl [NOTE NO SPACES IN THIS]
APN Protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecified
3) Then separately create another new APN and enter the following:
Name: AT&T US MMS
APN: wap.cingular
Proxy: wireless.cingular.com
Port: 80
Username: not set
Password: not set
Server: not set
MMSC: http://www.mmsc.cingular.com
MMS Proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC: 410
Authentication type: not set
APN type: mms
APN protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecify
4) Make sure the little circle next to AT&T pta is green.
5) Wait for the device to connect and then restart it.
I had a hard time finding these settings, so I thought it might be helpful to someone else here.
Parent/Teacher Association
oscillik said:
Parent/Teacher Association
Click to expand...
Click to collapse
No. Bad joke.
Sent from my GT-I9100 using xda premium
Not to be too paranoid, but will messing with these settings make it appear you are, say, tethering? I don't want to lose my unlimited data on ATT and fear that changing anything to access faster speeds may flag me for using a computer?
Similar to when the Dolphin desktop mode was flagging people on ATT, prompting the carrier to accuse users of tethering...
I wasn't aware Galaxy Nexus had the proper radio for this...
nirvanayoda said:
After reviewing the GS2 thread on the same topic (http://forum.xda-developers.com/showthread.php?t=1109983), I thought it might be worthwhile to discuss this issue on the Nexus. I was not able to get the Nexus connected using the information in that thread. However, I was able to get it connected to pta using a slightly modified version of the Skyrocket settings, which I'll post below.
One quick question before I do that, though -- I am only able to get 3 mb/s or so on my Nexus in Houston (an AT&T favorite city). I am on the unlimited data SOC code for LTE: LDPPVM5 -- think that code is causing any problems?
Anyway, here are working settings to get to PTA (the one the Skyrocket uses):
1) Go to settings, more (under networks), Access Point Names
2) Click on the 3 dots to create a new APN, name it AT&T PTA, and enter the following:
Name: ATT pta
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMS Proxy: not set
MMS port: not set
MCC: 310
MNC: 410
Authentication type: not set
APN type: default,supl [NOTE NO SPACES IN THIS]
APN Protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecified
3) Then separately create another new APN and enter the following:
Name: AT&T US MMS
APN: wap.cingular
Proxy: wireless.cingular.com
Port: 80
Username: not set
Password: not set
Server: not set
MMSC: http://www.mmsc.cingular.com
MMS Proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC: 410
Authentication type: not set
APN type: mms
APN protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecify
4) Make sure the little circle next to AT&T pta is green.
5) Wait for the device to connect and then restart it.
I had a hard time finding these settings, so I thought it might be helpful to someone else here.
Click to expand...
Click to collapse
Are you using AT&T's LTE provisioned SIM? that's probably why you're seeing the issue. Also that SoC code is LTE provisioned code which doesn't help.
milan03 said:
Are you using AT&T's LTE provisioned SIM? that's probably why you're seeing the issue. Also that SoC code is LTE provisioned code which doesn't help.
Click to expand...
Click to collapse
I am using an AT&T LTE provisioned SIM and my SOC code is LTE, so that could be part of the problem. But also keep in mind, I had that done just in case AT&T ever started to refuse to upgrade unlimited data users to LTE unlimited data. Right now, they're eager to get the LTE towers full, so they won't stop such upgrades -- that may change in the future.
Anyway, I played with my settings for a long time tonight and realized that APN type needs to read "default,internet,supl", not just "default,supl". I have no idea what that means or why it matters, but when I changed that, my speeds definitely increased. To give a comparison, at 1 AM, I got the following speeds:
default wap.cingular APN -- 4-5 Mb for most test servers
phone APN (as described in the thread linked in the OP) -- Average of 5 Mb for most test servers and high of 6 Mb
pta APN (as described above) -- average of 7 Mb for most test servers and high of 8 Mb
The difference isn't exactly extreme, and it's far lower than I'd hoped for, but I think pta is demonstrably faster, at least in my area. I'm eager to see how it does during the work day tomorrow.
I just tried this in Saint Lous, MO and I get no data service with pta
sluflyer06 said:
I just tried this in Saint Lous, MO and I get no data service with pta
Click to expand...
Click to collapse
Are you sure this line was exact (with no spaces)? Without "default" there it won't get me data services either, but with it I do:
APN type: default,internet,supl
No data for me either, reverted back to the dault cingular apn...though the HSPA+ phone APN that is floating around these board damn near doubled my speeds.
mrflips said:
No data for me either, reverted back to the dault cingular apn...though the HSPA+ phone APN that is floating around these board damn near doubled my speeds.
Click to expand...
Click to collapse
Just curious... If the HSPA+ APN doubled your speed, then why go back to the default cingular settings?
Im confused, why would the PTA apn do anything in the first place? i thought the i9250 version of the GNex isnt equiped with an LTE radio. Im in Los Angeles, CA where theres no LTE, i cant even get data with the PTA APN on my skyrocket. Unless I am mistaken and theres an LTE radio? id be so happy. Can anyone confirm? GSMARENA.COM list the specs for the i9250 with LTE 700mhz but other sites dont.
oatterzonxda said:
Im confused, why would the PTA apn do anything in the first place? i thought the i9250 version of the GNex isnt equiped with an LTE radio. Im in Los Angeles, CA where theres no LTE, i cant even get data with the PTA APN on my skyrocket. Unless I am mistaken and theres an LTE radio? id be so happy. Can anyone confirm? GSMARENA.COM list the specs for the i9250 with LTE 700mhz but other sites dont.
Click to expand...
Click to collapse
The 9250 doesn't have LTE. It's HSPA+.
oatterzonxda said:
Im confused, why would the PTA apn do anything in the first place? i thought the i9250 version of the GNex isnt equiped with an LTE radio. Im in Los Angeles, CA where theres no LTE, i cant even get data with the PTA APN on my skyrocket. Unless I am mistaken and theres an LTE radio? id be so happy. Can anyone confirm? GSMARENA.COM list the specs for the i9250 with LTE 700mhz but other sites dont.
Click to expand...
Click to collapse
It does not have LTE. It has HSPA+ (which AT&T and T-Mobile advertise as 4G). The poster here was saying he previously used a Galaxy S II Skyrocket (which is an AT&T LTE device) and because of that, his data plan is LTE and his SIM is an LTE SIM.
Anyway, I used the APN settings listed around this board and it doesn't seem to make a difference. When I used the settings posted, speedtest wouldn't work properly. It said I was getting 7kbps when it clearly wasn't that slow in real world usage. Going back to default fixed that issue, but I'm only getting about 3.5mbps down. I'd be happy to be getting 5. I already called AT&T and confirmed I've been changed over to an HSPA+ data SOC. Also, I got a new SIM card yesterday since my last one was from when I got my iPhone 3GS a couple years ago.
nirvanayoda said:
I am on the unlimited data SOC code for LTE: LDPPVM5 -- think that code is causing any problems?
Click to expand...
Click to collapse
If you have an LTE SOC, you can use the LTE APN but the device doesn't support LTE. You might as well get the HSPA+ SOC and use the HSPA+ APN.
milan03 said:
Are you using AT&T's LTE provisioned SIM? that's probably why you're seeing the issue. Also that SoC code is LTE provisioned code which doesn't help.
Click to expand...
Click to collapse
Using the latest AT&T LTE compatible SIM will not cause a problem. It is backward compatible with all AT&T plans. As for an incorrect SOC, well that's a different story and may have unpredictable results although a number of people have different SOCs/APNs working to their satisfaction.
Since a lot of people here think the LTE SIM is not compatible with HSPA/HSPA+, I am posting part of an official communique for "company owned" device users that went out just before the new LTE SIM was rolled out:
ATT said:
Next Generation SIM card for 4G devices now available
The new SIM card for 4G LTE devices is available for ordering in the COU system. While this SIM is required for 4G LTE devices, it is also compatible with 3G devices and COU will be shipping the 4G LTE SIM with every device make and model going forward (with exception to iPhone 4/iPad 3G +WiFi).
The new SIM (SKU 73057) includes enhancements that will enable functionality for LTE capable devices when supported by the network.
Click to expand...
Click to collapse
nirvanayoda said:
EDIT: OP EDITED WITH CHANGED PTA SETTINGS UNDER APN TYPE!
After reviewing the GS2 thread on the same topic (http://forum.xda-developers.com/showthread.php?t=1109983), I thought it might be worthwhile to discuss this issue on the Nexus. I was not able to get the Nexus connected using the information in that thread. However, I was able to get it connected to pta using a slightly modified version of the Skyrocket settings, which I'll post below.
One quick question before I do that, though -- I am only able to get 3 mb/s or so on my Nexus in Houston (an AT&T favorite city). I am on the unlimited data SOC code for LTE: LDPPVM5 -- think that code is causing any problems?
Anyway, here are working settings to get to PTA (the one the Skyrocket uses):
1) Go to settings, more (under networks), Access Point Names
2) Click on the 3 dots to create a new APN, name it AT&T PTA, and enter the following:
Name: ATT pta
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMS Proxy: not set
MMS port: not set
MCC: 310
MNC: 410
Authentication type: not set
APN type: default,internet,supl [NOTE NO SPACES IN THIS]
APN Protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecified
3) Then separately create another new APN and enter the following:
Name: AT&T US MMS
APN: wap.cingular
Proxy: wireless.cingular.com
Port: 80
Username: not set
Password: not set
Server: not set
MMSC: http://www.mmsc.cingular.com
MMS Proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC: 410
Authentication type: not set
APN type: mms
APN protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecify
4) Make sure the little circle next to AT&T pta is green.
5) Wait for the device to connect and then restart it.
I had a hard time finding these settings, so I thought it might be helpful to someone else here.
Click to expand...
Click to collapse
my account is LTE provisioned too(came from skyrocket) and these are almost the exact settings I ended up with as well after messing around with them and comparing with other skyrockets and SG2.
i have not been using the "internet" in the "default,internet,supl" setting, I just had "default,supl".
i have added the internet to see if I see any changes. these are the fastest Ive been able to get my GN to perform at. still not as fast as my skyrocket was using h+, and the MMS take a while to send/recieve sometimes.
nirvanayoda said:
EDIT: OP EDITED WITH CHANGED PTA SETTINGS UNDER APN TYPE!
After reviewing the GS2 thread on the same topic (http://forum.xda-developers.com/showthread.php?t=1109983), I thought it might be worthwhile to discuss this issue on the Nexus. I was not able to get the Nexus connected using the information in that thread. However, I was able to get it connected to pta using a slightly modified version of the Skyrocket settings, which I'll post below.
One quick question before I do that, though -- I am only able to get 3 mb/s or so on my Nexus in Houston (an AT&T favorite city). I am on the unlimited data SOC code for LTE: LDPPVM5 -- think that code is causing any problems?
Anyway, here are working settings to get to PTA (the one the Skyrocket uses):
1) Go to settings, more (under networks), Access Point Names
2) Click on the 3 dots to create a new APN, name it AT&T PTA, and enter the following:
Name: ATT pta
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMS Proxy: not set
MMS port: not set
MCC: 310
MNC: 410
Authentication type: not set
APN type: default,internet,supl [NOTE NO SPACES IN THIS]
APN Protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecified
3) Then separately create another new APN and enter the following:
Name: AT&T US MMS
APN: wap.cingular
Proxy: wireless.cingular.com
Port: 80
Username: not set
Password: not set
Server: not set
MMSC: http://www.mmsc.cingular.com
MMS Proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC: 410
Authentication type: not set
APN type: mms
APN protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecify
4) Make sure the little circle next to AT&T pta is green.
5) Wait for the device to connect and then restart it.
I had a hard time finding these settings, so I thought it might be helpful to someone else here.
Click to expand...
Click to collapse
Confirm that after obtaining new SIM to replace my 3 year old one and provisioning with a Skyrocket IEMI with LTE unlimited data plan I now am regularly 5Mbps down and hit 7-8Mbps at times. Latency is around 130ms.
MMS not playing nice. I haven't tested send and receive enough to say it works for me or not. I'll check in the morning when texting.
updated: no mms
lpasq said:
Confirm that after obtaining new SIM to replace my 3 year old one and provisioning with a Skyrocket IEMI with LTE unlimited data plan I now am regularly 5Mbps down and hit 7-8Mbps at times. Latency is around 130ms.
MMS not playing nice. I haven't tested send and receive enough to say it works for me or not. I'll check in the morning when texting.
updated: no mms
Click to expand...
Click to collapse
Have you tried using apn: phone? with the mms settings? Just wondering.
ebaul said:
Have you tried using apn: phone? with the mms settings? Just wondering.
Click to expand...
Click to collapse
Yes. Thank you. I did do so. My calls to ATT level 2 tech support and then a Supervisor now claim my issue is related to provisioning. The sim is correctly provisioned as pta with APN type settings as default,internet,mms,supl. I am told my account settings as part of my customer profile does not correctly reflect my IEMI and therefore my MMS feature is wonked. Sounds like I am in the customer service black hole waiting for my service ticket to make it through helpless-desk hell. There is something to what I am being spun because my online account is all screwed up. I love smartphone gadgets and hate wireless carriers!
lpasq said:
Yes. Thank you. I did do so. My calls to ATT level 2 tech support and then a Supervisor now claim my issue is related to provisioning. The sim is correctly provisioned as pta with APN type settings as default,internet,mms,supl. I am told my account settings as part of my customer profile does not correctly reflect my IEMI and therefore my MMS feature is wonked. Sounds like I am in the customer service black hole waiting for my service ticket to make it through helpless-desk hell. There is something to what I am being spun because my online account is all screwed up. I love smartphone gadgets and hate wireless carriers!
Click to expand...
Click to collapse
Ok, for the sake of argument, try this please and report back. I have a Vivid that I bought unsubs, therefore I didn't get it from at&t, but from Tigerdirect.com and I had to set my apn because I live in York, PA and there is no LTE here. I am able to send and receive mms and access internet at 6+ mbps and I didn't call at&t to report my new phone. Here are my APN settings:
I setup 2 apns, below are both:
APN1:
Name: AT&T HSPA+
(everything else leave blank until the end, which you will
APN type: default,admin,fota,hipri
APN2:
Name: AT&T MMS
APN: wap.cingular
MMSC: http://mmsc.cingular.com
MMS proxy: wireless.cingular.com
MMS port: 80
APN type: mms
Those are my settings and again I can send and receive MMS and access internet. Ensure the radio is clicked on AT&T HSPA+
Hope this helps.
Are you having issues with LTE on an AOSP ROM? Look here for information, and post any questions you may have about the subject.
First, we need to debunk the carrier's explanation of 4g. The carriers will explain to you that if it says 4g on the stock ROM you are using LTE. That is NOT true, 4g on the stock ROM is actually H, or H+, which is technically 3.5g, and not LTE. The stock ROM displays LTE as 4g LTE
So the first thing you need to do is make SURE you are in a location that has LTE coverage. Go to your carrier's website and verify with their coverage map
Coverage Maps:
AT&T
Rogers
Bell
Telus
AOSP based ROMs display your true network connectivity as follows:
G = GPRS
E = EDGE
3g = 3g
H = HSDPA / HSPA
H+ = HSDPA+ / HSPA+
4g = LTE
For Canadian users, you MUST verify LTE / GSM / WCDMA is selected.
The Dialer Code is *#*#DATA*#*# (or *#*#4636#*#*). You will enter the Data Programming menu, to set it.
Here is an app that will access the menu for you:
LTEOnOFF
Reported ROMs the settings stick on reboot:
CM10
SlimBean
AOKP
Now you have to verify you are using the correct LTE APN settings, and if not, add it.
You can access your APNs by "System Settings => More => Mobile networks => Access Point Names"
Here are the LTE settings for ALL US and Canadian carriers:
AT&T
Name: ATT PTA
APN: pta
MMSC: http://mmsc.mobile.att.net
MMS Proxy: proxy.mobile.att.net
MMS port: 80
MCC: 310
MNC: 410
Auth: none
APN type: default,mms,supl,hipri
Rogers
APN - ltemobile.apn
Proxy - <not set>
Port - <not set>
Username- <Not set>
Passwors - <not set>
Server < not set>
MMSC - http://mms.gprs.rogers.com
MMS - proxy 10.128.1.69
MMS - Port 80
MMS protocol - Wap 2.0 or Blank
MCC - 302
MNC - 720
Aythentication type - < not set>
APN type - either "*" or "internet + mms" Should work
Bell
APN: pda.bell.ca
Proxy: web.wireless.bell.ca
Port:80
Username: Not set
Password: Not set
Server: Not set
MMSC: http://mms.bell.ca/mms/wapenc
MMS Proxy: web.wireless.bell.ca
MMS Port: 80
MCC:302
MNC: 610
Authentication Type: Not set
APN Type: Not set
Telus
NAME: TELUS SP
APN: sp.telus.com
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMSC: http://aliasredirect.net/proxy/mmsc
MMS Proxy: 74.49.0.18
MMS Port: 80
MMS Protocol: WAP 2.0
MCC: 302
MNC: 220
Authentication type: not set
APN Type: default,mms,hipri
Bearer: unspecified
Alaska Communications (ACS)
2 APNs
Data APN:
Name: ACS Data
APN: web.acs
MCC 311 (Default)
MNC 370 (Default)
APN type: “default,supl” or “*”
MMS APN:
Name: ACS MMS
APN: mms.acs
MMSC: http://mmsc.gci.csky.us:6672
MMS proxy: 209.4.229.92
MMS port: 9201
MCC 311 (Default)
MNC 370 (Default)
APN type: mms
Or the easiest way to do it would be just to edit the two current (GCI) APNs and change in the APN where ‘gci’ is listed to ‘acs’.
-Frozen
Fido
apn: ltemobile.apn
mmsc: http://mms.fido.ca
mms proxy: 204.151.11.13
mms port: 80
mcc: 370
apn type: internet +mms
reserved for god
My lte wasn't working when I flashed to cm10 yesterday. I did the steps you stated, deleted all other apn other than the rogerslte one and restarted my phone. It has been working since then.
Sent from my SGH-I747 using xda app-developers app
Deoxlar said:
My lte wasn't working when I flashed to cm10 yesterday. I did the steps you stated, deleted all other apn other than the rogerslte one and restarted my phone. It has been working since then.
Sent from my SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
Carrier? could you post your settings for help with the guide? If they look exactly the same, just say theyre the same...
I'm with Rogers, everything is the same except for the mms protocol. I left mine blank instead of Wap 2.0
I believe cm10 sometimes resets some settings back to default if you don't reboot after changing a setting. But I'm not 100percent sure.
Sent from my SGH-I747 using xda app-developers app
Deoxlar said:
I'm with Rogers, everything is the same except for the mms protocol. I left mine blank instead of Wap 2.0
Sent from my SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
fixed, thx
Will place in AT&T Index shortly.
Excellent job... noob
I'd like to mention that the LTE / GSM / WCDMA selection does not revert after every reboot on any Canadian S3 that I know of with CM10, and has never done so to my knowledge. If this is happening in other AOSP ROMs, it is a ROM specific problem.
The setting does revert to the default after a data wipe though.
Could users of other AOSP ROMs comment on does it stick on reboot?
Quasimodem said:
Could users of other AOSP ROMs comment on does it stick on reboot?
Click to expand...
Click to collapse
I've been using Slimbean 2.6 and 2.7 for several weeks now and can confirm LTE is sticking. However I certainly don't think I'm getting the as high a LTE connectivity rate as with the stock rom.
finneginsfast said:
I've been using Slimbean 2.6 and 2.7 for several weeks now and can confirm LTE is sticking. However I certainly don't think I'm getting the as high a LTE connectivity rate as with the stock rom.
Click to expand...
Click to collapse
There's so many factors that can contribute to that... too ambiguous to T/S.... It's a trial and error thing... Location, network traffic, and the modem you're currently running...
Quasimodem said:
There's so many factors that can contribute to that... too ambiguous to T/S.... It's a trial and error thing... Location, network traffic, and the modem you're currently running...
Click to expand...
Click to collapse
This is definitely true. Only way I can tell though with a degree of certainty is with a network monitoring app and the fact that I've got pretty standard area of operation.
I've been running kyanrom though for the past couple days and I'm back to getting a much higher degree of LTE connections. I guess while I'm at it, I can also confirm that LTE is sticking with kyanrom also.
APNs for Alaska Communications (ACS)
Alaska Communications (ACS), 2 APNs
Change Network Mode to LTE/GSM/WCDMA
Data APN:
Name: ACS Data
APN: web.acs
MCC 311 (Default)
MNC 370 (Default)
APN type: “default,supl” or “*”
MMS APN:
Name: ACS MMS
APN: mms.acs
MMSC: hxxp://mmsc.gci.csky.us:6672
MMS proxy: 209.4.229.92
MMS port: 9201
MCC 311 (Default)
MNC 370 (Default)
APN type: mms
Or the easiest way to do it would be just to edit the two current (GCI) APNs and change in the APN where ‘gci’ is listed to ‘acs’.
Change hxxp to http.
-Frozen
Hello,
having LTE issues (Not getting LTE) with Task & Ktoonsez AOKP rom, I have it set to LTE/GSM (PRL) mode (*#*#4636#*#* menu) and when I go into settings>More>Mobile Networks>Network Mode, I have it set to: LTE/GSM/WCDMA mode, and all I get is H and H+ still. I have the LTE APN and have it selected, and still no luck. I had a SIM replacement from Virgin Mobile, but it didn't do any good. When I put it on LTE only mode I lose connection to my carrier. So I keep it on LTE/GSM mode, but still getting no LTE. Anything I can do to fix this? Thanks. It used to work when I had Team Insomnia's Jellybean rom, I had 4g but got no where near LTE speeds. Would this be a Virgin Mobile problem?
Papaniz said:
Hello,
having LTE issues (Not getting LTE) with Task & Ktoonsez AOKP rom, I have it set to LTE/GSM (PRL) mode (*#*#4636#*#* menu) and when I go into settings>More>Mobile Networks>Network Mode, I have it set to: LTE/GSM/WCDMA mode, and all I get is H and H+ still. I have the LTE APN and have it selected, and still no luck. I had a SIM replacement from Virgin Mobile, but it didn't do any good. When I put it on LTE only mode I lose connection to my carrier. So I keep it on LTE/GSM mode, but still getting no LTE. Anything I can do to fix this? Thanks. It used to work when I had Team Insomnia's Jellybean rom, I had 4g but got no where near LTE speeds. Would this be a Virgin Mobile problem?
Click to expand...
Click to collapse
When you were on the TouchWiz ROM did it only say 4g and not 4g LTE? It would say 4g LTE in a TouchWiz ROM... You may not be in an LTE area...
Quasimodem said:
When you were on the TouchWiz ROM did it only say 4g and not 4g LTE? It would say 4g LTE in a TouchWiz ROM... You may not be in an LTE area...
Click to expand...
Click to collapse
Oh it only had 4G on it. I did check the map for Virgin and yeah I am in an LTE area. I don't know it may be a Virgin Mobile issue.
Sent from my SGH-I747 using xda app-developers app
Papaniz said:
Oh it only had 4G on it. I did check the map for Virgin and yeah I am in an LTE area. I don't know it may be a Virgin Mobile issue.
Sent from my SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
If it only had 4G on it you were never getting lte in the first place... Might wanna call them.. . Do u mind posting your apn settings for the op?
Not sent from your phone...
Quasimodem said:
If it only had 4G on it you were never getting lte in the first place... Might wanna call them.. . Do u mind posting your apn settings for the op?
Not sent from your phone...
Click to expand...
Click to collapse
Sure..
Name: Bell LTE
APN: pda.bell.ca
Proxy: web.wireless.bell.ca
Port:80
MMSC: http://mms.bell.ca/mms/wapenc
MMS Proxy: web.wireless.bell.ca
MMS Port: 80
MCC: 302
MNC: 610
Authentication Type: Not Set
APN Type: Not Set
APN Protocol: IPv4
Bearer: Unspecified
EDIT: I think I got it, I am on a Virgin Mobile Supertab (From old phone still being paid off) and changed from that older phone, that didn't have LTE, to the S3 , I went into my Virgin Mobile "My Account' and it showed my phones it only listed the HTC Legend I had few months ago, but not the S3 itself, and beside it saying this device runs on a HSPA+ network. I'm getting this fixed on Monday so I'll see what happens then. If somebody can do it sooner though if they have the same issue with Virgin Mobile/Bell, that would be great too. The system I guess still thinks that I have the HTC Legend which doesn't run LTE.
Anybody on the Bell network having signal problems while running AOKP? I can't seem to get my phone to run LTE and my signal drops randomly. I've wiped, fixed permissions, enabled the proper settings and still nothing.
IUH1991 said:
Anybody on the Bell network having signal problems while running AOKP? I can't seem to get my phone to run LTE and my signal drops randomly. I've wiped, fixed permissions, enabled the proper settings and still nothing.
Click to expand...
Click to collapse
On the stock rom did it say 4G lte?
Not sent from your phone...
Hi
So long story short, my Tmo GS3 got stolen at my work :/
So my mom gave me her ATT GS3 cus she was up for an upgrade,
i been reading its possible to get 4G on an ATT GS3 but so far no luck,
i know i have the right APN cus i copied the one from my Nex4 to my GS3, i set the network to manual and choose Tmo, but still all i get is Edge.
Does it have to do something with the way i unlocked the phone?
I been reading it has to be factory unlock and i unlocked mine by dialing *#197328640# and doing the required steps.
Can anyone help me with this?
orphan22 said:
Hi
So long story short, my Tmo GS3 got stolen at my work :/
So my mom gave me her ATT GS3 cus she was up for an upgrade,
i been reading its possible to get 4G on an ATT GS3 but so far no luck,
i know i have the right APN cus i copied the one from my Nex4 to my GS3, i set the network to manual and choose Tmo, but still all i get is Edge.
Does it have to do something with the way i unlocked the phone?
I been reading it has to be factory unlock and i unlocked mine by dialing *#197328640# and doing the required steps.
Can anyone help me with this?
Click to expand...
Click to collapse
Do a little bit of search work; it depends on the coverage for T-Mobile in your area. It's still a Work in Progress to get the 1700 Mhz band to work on a ATT GS3 since there's a bounty for it in the General section.
Setting the APN to what you have on the Nex4 won't do anything because it's all software and hardware controlled. The software part is currently locked down because no one knows what to change to get the hardware to send and recieve information from the 1700Mhz Band.
Your best bet is to check the coverage map and hope you get 3G service or wait until T-Mobile Rolls out their 4G so the old EDGE will switch onto HSPA for ATT devices that use a T-Mobile Network.
Hope this helps
hD
orphan22 said:
Hi
So long story short, my Tmo GS3 got stolen at my work :/
So my mom gave me her ATT GS3 cus she was up for an upgrade,
i been reading its possible to get 4G on an ATT GS3 but so far no luck,
i know i have the right APN cus i copied the one from my Nex4 to my GS3, i set the network to manual and choose Tmo, but still all i get is Edge.
Does it have to do something with the way i unlocked the phone?
I been reading it has to be factory unlock and i unlocked mine by dialing *#197328640# and doing the required steps.
Can anyone help me with this?
Click to expand...
Click to collapse
I was wondering myself smdh when im in landover md. I get good 4g. And soon as get greenbelt md all get is edge. Or maybe 3g. Or h
Sent from my SGH-I747 using Tapatalk 2
Try these apn settings if they arent what you're already using. They've worked for S3 users before.
Name: Straight Talk
APN: att.mvno
Proxy: <not set>
Port: <not set>
MMSC: http://mmsc.cingular.com
MMS Proxy: 66.209.11.33
MMS Port: 80
APN Type: default,supl,mms,hipri
xBeerdroiDx said:
Try these apn settings if they arent what you're already using. They've worked for S3 users before.
Name: Straight Talk
APN: att.mvno
Proxy: <not set>
Port: <not set>
MMSC: http://mmsc.cingular.com
MMS Proxy: 66.209.11.33
MMS Port: 80
APN Type: default,supl,mms,hipri
Click to expand...
Click to collapse
Arent those att apns? I need it to work foor tmo...
Sent from my Nexus 4 using xda app-developers app
orphan22 said:
Arent those att apns? I need it to work foor tmo...
Sent from my Nexus 4 using xda app-developers app
Click to expand...
Click to collapse
correct. my mistake. posted the wrong ones. what are your current apn settings?
i came across these:
APN: epc.tmobile.com
Proxy:
Port:
Username:
Password:
Server:
MMSC: http://mms.msg.eng.t-mobile.com/mms/wapenc
MMS Proxy:
MMS Port:
MCC: 310
MNC: 260
Authentication Type:
APN Type: default,supl,admin,dun,mms
APN Protocol: IPv4/IPv6
APN Roaming Protocol: IPv4/IPv6
and this one as well.
Name : T-Mobile LTE
APN: fast.tmobile.com
MMSC: http://mms.msg.eng.t-mobile.com/mms/wapenc
MMS Protocol: WAP 2.0
MCC: 310
MNC: 260
APN Type: default,supl,admin,dun,mms
xBeerdroiDx said:
correct. my mistake. posted the wrong ones. what are your current apn settings?
i came across these:
APN: epc.tmobile.com
Proxy:
Port:
Username:
Password:
Server:
MMSC: http://mms.msg.eng.t-mobile.com/mms/wapenc
MMS Proxy:
MMS Port:
MCC: 310
MNC: 260
Authentication Type:
APN Type: default,supl,admin,dun,mms
APN Protocol: IPv4/IPv6
APN Roaming Protocol: IPv4/IPv6
and this one as well.
Name : T-Mobile LTE
APN: fast.tmobile.com
MMSC: http://mms.msg.eng.t-mobile.com/mms/wapenc
MMS Protocol: WAP 2.0
MCC: 310
MNC: 260
APN Type: default,supl,admin,dun,mms
Click to expand...
Click to collapse
In going to try them. Thanks a lot.
Sent from my Nexus 4 using xda app-developers app
HermitDash said:
Do a little bit of search work; it depends on the coverage for T-Mobile in your area. It's still a Work in Progress to get the 1700 Mhz band to work on a ATT GS3 since there's a bounty for it in the General section.
Setting the APN to what you have on the Nex4 won't do anything because it's all software and hardware controlled. The software part is currently locked down because no one knows what to change to get the hardware to send and recieve information from the 1700Mhz Band.
Your best bet is to check the coverage map and hope you get 3G service or wait until T-Mobile Rolls out their 4G so the old EDGE will switch onto HSPA for ATT devices that use a T-Mobile Network.
Hope this helps
hD
Click to expand...
Click to collapse
I get really good 4G over 18MB on my nex4.
Sent from my Nexus 4 using xda app-developers app
Hey orphan did it work
Sent from my SGH-T959V using xda premium
HolyGhostBoy1 said:
Hey orphan did it work
Sent from my SGH-T959V using xda premium
Click to expand...
Click to collapse
No :/ still only edge. Is there a way to know what band 1700Mhz for example do i get in mi zone?
Sent from my Nexus 4 using xda app-developers app
I had the same situation: only edge, after flashing this files i have 4g http://forum.xda-developers.com/showthread.php?t=1771021&page=25.
Start reading from post #246. If you flash the files you must root your phone like it is a t999, also goes for recovery, im not sure about kernel and DO NOT flash another modem/radio.
Alright guys, I have this weird problem with my S4. Most of the time my mobile data doesnt work nor show the lte symbol even when data is enabled. Everytime I disconnect from my wifi, my data doesnt come on after a while. Do i need to update my modem or any other solution? I've attached done pictures to show it and my device info.
Sent from my SGH-M919 using Tapatalk 2
check your APN & make sure its selected. Try that to see if that helps or not.
I had the same exact issue. Your baseband is MDB and your build is MDL. Your network settings are LTE/GSM auto. Change it to GSM/WCDMA, if you get back your 4G icon then you'll need to either flash a MDB build or just Odin the stock MDL tar file. I did a full wipe and Odin the MDL tar and that fixed my problem.
Sent from my SGH-M919 using Tapatalk 2
Sounds like a apn setting mismatch, if you could send screenshot of your apn id better be able to tell and help you fix
Sent from my SGH-M919 using Tapatalk 2
Xcor3 said:
Alright guys, I have this weird problem with my S4. Most of the time my mobile data doesnt work nor show the lte symbol even when data is enabled. Everytime I disconnect from my wifi, my data doesnt come on after a while. Do i need to update my modem or any other solution? I've attached done pictures to show it and my device info.
Click to expand...
Click to collapse
Try using these APN settings, It worked for someone in the wicked thread:
Name : T-Mobile LTE
APN: fast.tmobile.com
MMSC: http://mms.msg.eng.t-mobile.com/mms/wapenc
MMS Protocol: WAP 2.0
MCC: 310
MNC: 260
APN Type: default,supl,admin,dun,mms
Works as it should now. Thank you
Sent from my SGH-M919 using Tapatalk 2
saldebot said:
Try using these APN settings, It worked for someone in the wicked thread:
Name : T-Mobile LTE
APN: fast.tmobile.com
MMSC: http://mms.msg.eng.t-mobile.com/mms/wapenc
MMS Protocol: WAP 2.0
MCC: 310
MNC: 260
APN Type: default,supl,admin,dun,mms
Click to expand...
Click to collapse
Hey do u have the international gt-i9500 and are using it on Tmobile. If so how do u get network data to get anything besides edge?
calibachrome said:
Hey do u have the international gt-i9500 and are using it on Tmobile. If so how do u get network data to get anything besides edge?
Click to expand...
Click to collapse
Sorry bro, I have the TMO SGH-M919....
I thought matching baseband and software would help me, but it didn't. Was on the phone with tmobile for 40 minutes. I wasnt getting any data in LTE settings while my friend with the note 2 standing next to me was in 4g mode. New phone was sent out next day free, got it yesterday and all is working. Even updated to official MDL
saldebot said:
Try using these APN settings, It worked for someone in the wicked thread:
Name : T-Mobile LTE
APN: fast.tmobile.com
MMSC: http://mms.msg.eng.t-mobile.com/mms/wapenc
MMS Protocol: WAP 2.0
MCC: 310
MNC: 260
APN Type: default,supl,admin,dun,mms
Click to expand...
Click to collapse
Hey! This began to work for me. But I have a question - I don't see MMS protocol anywhere in the aPN settings. I set everything else. Is that alright?
I need to try this I have note 2 getting lte and my girlfriend phone is not
this is the correct one..
Name: T-Mobile US
APN: fast.t-mobile.com
MMSC: http://mms.msg.eng.t-mobile.com/mms/wapenc
MMS Proxy: Not set
MMS port: Not set
MCC: 310
MNC: 260
Auth: Not set
APN type: default,mms,supl
APN protocol: IPv4/IPv6
APN roaming protocol: IPv4/IPv6
Mine is not working too.. my mobile data has not working even I reset it.. what to do?
AxAtAx said:
this is the correct one..
Name: T-Mobile US
APN: fast.t-mobile.com
MMSC: http://mms.msg.eng.t-mobile.com/mms/wapenc
MMS Proxy: Not set
MMS port: Not set
MCC: 310
MNC: 260
Auth: Not set
APN type: default,mms,supl
APN protocol: IPv4/IPv6
APN roaming protocol: IPv4/IPv6
Click to expand...
Click to collapse
Do these settings vary by region?
State? Time zone?
Or can this be applied to any phone anywhere.
Pp.
Just curious as I'm having the same issue. I've got the t919 but I'm running on at towers (net10) I had no issues until I loaded a custom ROM. Could it be because I flashed a tmo ROM or should I use a att based ROM?
Hi, I was wondering if anyone else had a similar problem or can help with a solution. I just got my Oppo 7 (love this thing) but it seems the network doesn't work properly. The network seems to be picked up just fine, full bars, under network settings it automatically acquires the APN settings and everything, but I can't do anything over the air without WiFi. As soon as the WiFi is gone, I can't browse the internet, send or receive text messages, etc. What do?
Will this help? Won't be LTE, but H+ (my phone doesn't have LTE)
APN: att.mvno
Proxy : wireless.cingular.com
Port: 80
MMSC: http://mmsc.cingular.com
MMS Port: 80
MCC: 310
MMC: 410
APN Type: default,supl,mms
APN Protocol: IPv4
APN Roaming: IPv4
Chuteboxe39 said:
Hi, I was wondering if anyone else had a similar problem or can help with a solution. I just got my Oppo 7 (love this thing) but it seems the network doesn't work properly. The network seems to be picked up just fine, full bars, under network settings it automatically acquires the APN settings and everything, but I can't do anything over the air without WiFi. As soon as the WiFi is gone, I can't browse the internet, send or receive text messages, etc. What do?
Click to expand...
Click to collapse
I have mine set up on T Mobile and I'm having the same problem. It's pretty annoying. I've tried a factory reset to no avail. My phone downloaded an update this morning which I hoped would fix the problem, but it looks like it hasn't.
Chuteboxe39 said:
Hi, I was wondering if anyone else had a similar problem or can help with a solution. I just got my Oppo 7 (love this thing) but it seems the network doesn't work properly. The network seems to be picked up just fine, full bars, under network settings it automatically acquires the APN settings and everything, but I can't do anything over the air without WiFi. As soon as the WiFi is gone, I can't browse the internet, send or receive text messages, etc. What do?
Click to expand...
Click to collapse
That's odd. There's one thing wrong with this device on stock - its APN database for AT&T is 3-4 years out of date. It was still using the wap.cingular APN when I turned mine on.
You need to manually put in the AT&T LTE APN (pta). ALSO if you've never owned an LTE device before you'll need to talk to AT&T to have your account updated. (Using the pta APN with a Nexus 5 resulted in no data for me too until I had my plan/account updated. You can do this without an actual contract change - for example I'm still grandfathered in to "unlimited data"). In general I would recommend doing this in-person at an AT&T-owned store, not at the phone and not at a franchisee (like most small mall kiosks).
Thanks for the reply everyone, I entered in the new ATT HSPA+ APN and it works like a charm now.
Could you post your settings?. I confirmed the SIM I got yesterday was lte capable but still no dice.
Sent from my X9006 using XDA Free mobile app
jgunna405 said:
Could you post your settings?. I confirmed the SIM I got yesterday was lte capable but still no dice.
Sent from my X9006 using XDA Free mobile app
Click to expand...
Click to collapse
Just putting in the pta APN with no other info was enough for me.
(MMS is probably borked for me until I fill in the right settings for it but I use MMS maybe once every 3 years at most.)
Entropy512 said:
Just putting in the pta APN with no other info was enough for me.
(MMS is probably borked for me until I fill in the right settings for it but I use MMS maybe once every 3 years at most.)
Click to expand...
Click to collapse
I just realized that you were in here Entropy. I appreciate the work you did with the Galaxy S2 (last phone I had before this one). Do you plan on doing any dev work with this one or are you going to take it easy?
mmsc: http://mmsc.mobile.att.net
mms proxy: proxy.mobile.att.net
mms port: 80
apn type: default,mms.supl
That's what I have currently and mms works fine.
jgunna405 said:
I just realized that you were in here Entropy. I appreciate the work you did with the Galaxy S2 (last phone I had before this one). Do you plan on doing any dev work with this one or are you going to take it easy?
mmsc: http://mmsc.mobile.att.net
mms proxy: proxy.mobile.att.net
mms port: 80
apn type: default,mms.supl
That's what I have currently and mms works fine.
Click to expand...
Click to collapse
I'm working on lighting up omni. Oppo sent us a few devices.
Thanks for the MMS info, I should stick that into my device.
jgunna405 said:
I just realized that you were in here Entropy. I appreciate the work you did with the Galaxy S2 (last phone I had before this one). Do you plan on doing any dev work with this one or are you going to take it easy?
mmsc: http://mmsc.mobile.att.net
mms proxy: proxy.mobile.att.net
mms port: 80
apn type: default,mms.supl
That's what I have currently and mms works fine.
Click to expand...
Click to collapse
I pulled the APN configs for ATT Phone APN from omni's github (I updated it a few months back to what it was from an AT&T stock TouchWiz Galaxy S4 ROM, so it this is update-to-date afaik)
I've bolded the ones that you actually need to touch, otherwise, don't touch them
Name: ATT Phone
APN: phone
Proxy: Not set
Port: Not set
Username: Not set
Password: Not set
Server: Not set
MMSC: http://mmsc.mobile.att.net
MMS proxy: proxy.mobile.att.net
MMS Port: 80
MCC: 310
MNC: 410
Authentication type: Not set
APN type: default,subl,mms,hipri (no spaces between them!!!!)
APN protocol: IPv4
APN roaming protocol: IPv4
APN enable/disable: APN enabled (this should be grayed out anyway)
Bearer: Unspecified
jakew02 said:
I pulled the APN configs for ATT Phone APN from omni's github (I updated it a few months back to what it was from an AT&T stock TouchWiz Galaxy S4 ROM, so it this is update-to-date afaik)
I've bolded the ones that you actually need to touch, otherwise, don't touch them
Name: ATT Phone
APN: phone
Proxy: Not set
Port: Not set
Username: Not set
Password: Not set
Server: Not set
MMSC: http://mmmsc.mobile.att.net
MMS proxy: proxy.mobile.att.net
MMS Port: 80
MCC: 310
MNC: 410
Authentication type: Not set
APN type: default,subl,mms,hipri (no spaces between them!!!!)
APN protocol: IPv4
APN roaming protocol: IPv4
APN enable/disable: APN enabled (this should be grayed out anyway)
Bearer: Unspecified
Click to expand...
Click to collapse
I have this as my settings now and still only get H+. (except for the mmsc, you have 3 m's)
Weird thing is that I get 0 connection when I change from phone to pta.
Not sure if locale is the culprit. I'm in Oklahoma City.
Sent from my X9006 using XDA Free mobile app
jgunna405 said:
I have this as my settings now and still only get H+. (except for the mmsc, you have 3 m's)
Weird thing is that I get 0 connection when I change from phone to pta.
Not sure if locale is the culprit. I'm in Oklahoma City.
Sent from my X9006 using XDA Free mobile app
Click to expand...
Click to collapse
whoops made a typo, yea it's only 2 m's in mmsc
try applying ATT Phone apn and rebooting,,
that's weird. did you call AT&T to confirm that you have the LTE data package on your account like Entropy512 stated ?
jakew02 said:
whoops made a typo, yea it's only 2 m's in mmsc
try applying ATT Phone apn and rebooting,,
that's weird. did you call AT&T to confirm that you have the LTE data package on your account like Entropy512 stated ?
Click to expand...
Click to collapse
I went to the ATT store, but they weren't any help. They confirmed that the SIM they gave me was lte compatible, but I assumed that's the same thing as having an LTE data package. I'll give them a call tonight and let you all know. (btw, just re-applied your settings and still no luck)
edit: called.. and they claim that all accounts have lte compatibility now and of course she had never heard of the OF7a
The settings entropy posted were the exact settings my N5 had which I copied over and worked fine. One thing to be aware of is that mine says 4G on LTE and then either H or H+ for those, not sure if this applies only to my service area or what and another might show differently. At any rate if you're getting 4G showing you might wanna run speedtest and see if you are getting LTE.
jgunna405 said:
I went to the ATT store, but they weren't any help. They confirmed that the SIM they gave me was lte compatible, but I assumed that's the same thing as having an LTE data package. I'll give them a call tonight and let you all know. (btw, just re-applied your settings and still no luck)
edit: called.. and they claim that all accounts have lte compatibility now and of course she had never heard of the OF7a
Click to expand...
Click to collapse
AT&T's SIMs have been LTE compatible for years, even before AT&T had an LTE network. I need to check to be sure, but I'm fairly certain my SIM is still the original "cut down SIM" that I've had since 2011 at least.
It's your account that needs to be LTE-enabled.
Don't call. Phone support is awful. Go to a corporate-owned AT&T physical store. That's where the competent staff are.
(In my case, I originally did the LTE upgrade on a Nexus 5 - if you put a SIM into a Nexus 5 that doesn't have LTE on the account, you'll get a text message saying to call AT&T.)