Develop Bugs

HTC Desire Help Needed

hello i have desire with
BRAVO PVT1 SHIP S-ON
HBOOT-0.93.001
MICROP-031D
TOUCH PANEL-SYNT0101
RADIO-5.11.05.27
AUG 10 2010.17:52:10
ITS STUCK ON HTC LOGO . I CAN GO IN HBOOT BUT PROBLEM IS I TRIED MANY ROMS BUT ITS ALWAYS SAY MAIN FIRMWARE IS OLDER FLASHING FAILED
ITS ORANGE BRANDED PHONE
PLEASE HELP NEEDED ANY EXPERT

Did you root?
Sent from CM7

no i dint root . can i root phone in this condotion? if possible please can u tell me the way?

you can root in hboot screen.
and root tools ,I suggest unrevoked 3.21 (root tools included clockworkmod 2.5.x recovery) .
good luck man.

You can't flash roms without rooting. Download this and if your on Windows, download the drivers too and also read the page so the drivers install properly. After you have done all of that, run the utility. Please be aware that issues may arrise when your done and no one but yourself takes responsibility what happens, but nontheless, it should be fine.
When your done rooting, go into the recovery and go to backup and restore > backup and it will backup the whole phone. Keep this just in case. It will go on your SD Card > clockworkmod/backup.

my phone is connected in HBOOT but unrevoked say connect phone in usb debugging mode now how can i connect in debuging while phone can only enter in HBOOT

I have the exact same problem, I applied the f***** HTC update and the phone never started afterwards. Just the HTC logo then reboots.
I will try to root the phone as suggested by Meaple and kosterz and will let you know how it turns.

HTC Desire help
Dear xda community
I have a O2 htc desire from uk. Warranty expired. ( now I m in Pakistan so it is not possible to me send it to htc company because here is no htc service shop and If I send it uk or other country expenditure are more than phone price) When I update it with 2.14.207.3 during updating wifi disconnect and phone stacked I remove the battery and on it. Now it stacked on htc logo and show 4 exclamation sign in triangular.
Picture
When I connect it with pc and then disconnect it screen will be appear
Picture
Bravo PVT1 ship s-on
Hboot-0.93 0001
Microp-031d
Toutch Panel-synt0101
Radio 0-5.11.05.27
Aug 10 2010.17.52.10
RUU
No volume key , menu key or back key work
I try to O2 2.14.207.1 rom Ruu upload but when it reached at 85% green installation bar full on the phone and message appear.
ERROR [110]: FILE OPEN ERROR
This error message indicates that the RUU lacks some specific files or they are damaged, so the RUU cannot continue with the update. You have to get the complete RUU package and try again.
And at the pc recover your phone after all process recover successful but when I on the phone it is on same condition
I download this rom from many sites and try it but result is same.
In RUU read me file they said that
Q: I used RUU to update and it failed. Now, my Android phone always boots in the RUU failed mode and cannot enter the Android Home screen anymore, what should I do?
A: This is normal and can be recovered. Follow the instructions below to reset your Android phone and to establish a connection with the PC.
1. Disconnect your Android phone from the USB cable.
2. Reset your Android phone (Remove and reinstall the battery).
3. Reconnect your Android Phone to the USB cable.
4. Check if the Android phone is recognized by the PC.
5. Return to the ROM Update Utility.
So please tell me any solution. I will be thankful to you.

anyhelp from anybody els?

Unrooting HTC Desire Hboot 0.8 Help

I've read several guides and I've tried several different RUU's
RUU_Bravo_Froy2_UK_2.14.207.1_Radio_32.44.00.32U_5.09.05.30_2_release_144166_signed.exe
RUU_Brav2_UK_1.20.207.1_Radio_32.36.00.28U_4.06.00.02_2_release_124865.exe
RUU_Bravo_HTC_WWE_1.21.405.2_Radio_32.36.00.28U_4.06.00.02_2_release_126984_signed.exe
All of them do the same thing, they connect to the phone start loading and when the phone is showing the hTC logo they say waiting for bootloader and then say an error occurred.
Some of the guides say leave the phone on the htc screen and reload the bootloader. The moment I exit the RUU installation the phone reboots to cyanogen mod. I've tried restarting etc.. leaving the phone in and just re-running. No luck, I cannot get the phone to stay on the hTC screen, it always restarts when I exit the program.
Any ideas as the phone needs repairing as the cpu crashes continuously!
Thanks
Bootloader details:
BRAVO PVT1 SHIP S-ON
HBOOT-0.80.0000
MICROP-031d
TOUCH PANEL-SYNT0101
RADIO-5.17.05.23
Mar 29 2010,21:34:33

DeliveryNinja said:
I've read several guides and I've tried several different RUU's
RUU_Bravo_Froy2_UK_2.14.207.1_Radio_32.44.00.32U_5.09.05.30_2_release_144166_signed.exe
RUU_Brav2_UK_1.20.207.1_Radio_32.36.00.28U_4.06.00.02_2_release_124865.exe
RUU_Bravo_HTC_WWE_1.21.405.2_Radio_32.36.00.28U_4.06.00.02_2_release_126984_signed.exe
All of them do the same thing, they connect to the phone start loading and when the phone is showing the hTC logo they say waiting for bootloader and then say an error occurred.
Some of the guides say leave the phone on the htc screen and reload the bootloader. The moment I exit the RUU installation the phone reboots to cyanogen mod. I've tried restarting etc.. leaving the phone in and just re-running. No luck, I cannot get the phone to stay on the hTC screen, it always restarts when I exit the program.
Any ideas as the phone needs repairing as the cpu crashes continuously!
Thanks
Bootloader details:
BRAVO PVT1 SHIP S-ON
HBOOT-0.80.0000
MICROP-031d
TOUCH PANEL-SYNT0101
RADIO-5.17.05.23
Mar 29 2010,21:34:33
Click to expand...
Click to collapse
Which error code occured? CID error? If yes, create a goldcard:
http://android.modaco.com/content/software/308798/pc-application-goldcardtool/
After this, pu this in your desire and flash ruu again:
RUU_Bravo_Froyo_HTC_WWE_2.29.405.5_Radio_32.49.00. 32U_5.11.05.27_release (If you want stock froyo)
RUU_Brav2_UK_1.20.207.1_Radio_32.36.00.28U_4.06 .00.02_2_release_124865.exe (If you want eclair rom with o2 rom (i guess that was your branding).

I get Error code 171 error connecting via usb. This is when it's just loaded the new bootloader and is sitting on the new htc logo. I then click exit and it throws me back to cyanogen mod.
I have the original gold card in from when I did the root.

Try the RUU on baadnwz.eu/search/label/addons
I've just them before i rooted my phone with Unrevoked

DeliveryNinja said:
I get Error code 171 error connecting via usb. This is when it's just loaded the new bootloader and is sitting on the new htc logo. I then click exit and it throws me back to cyanogen mod.
I have the original gold card in from when I did the root.
Click to expand...
Click to collapse
Sounds for me you could have an usb brick. Here is a guide how fix it:
http://forum.xda-developers.com/showthread.php?t=691639
When done, try to flash ruu like before again.

Okay,
I tried the usb brick fix. Made no difference. It was still throwing the 171 error.
I had a look around online and found you can grap the rom.zip file from the temp directory of windows while the RUU is running. I renamed this to PB99IMG.zip and dropped it on the root of the sd card (gold card) and then booted to hboot. This then started to install the new hboot 0.93 and O2 UK Froyo from the
RUU_Bravo_Froy2_UK_2.14.207.1_Radio_32.44.00.32 U_5.09.05.30_2_release_144166_signed.exe RUU.
Hope this helps if anyone else is stuck.

[Q] Stock Gingerbread Update results in Bootloop

Hi there!
Maybe this question was asked 100 times but I really searched and searched but dont found any solution for my problem.
I got a HTC Desire with stock froyo on it - no root - no CFW - just stock.
Phone sometimes doesnt boot. Just come to green HTC logo 1x vibrate and reboot. If this happens I pulled out the battery leave it alone for a hour pulled it back and it boots fine.
Because of this error I tried to fix it with latest dev update to gingerbread. Install went fine - succesful - reboot...
Since then im not able to acces the OS. It ALWAYS stucks at green HTC vibrate on time and reboot.
Damned. Tried to flash again via RUU - same ****. Tried to flash via SD - same ****.
I have acces to Hboot and fastboot but i think this doesnt help me anyway.
So please - if anyone has a solution how to fix my bootcycle problem - give me a hint.
---EDIT---
I dont know how but i have succesfully boot into GB. Immediatly I used revolutionary to get S-OFF. Done.
Now Phone looks like it boots normally. Strange thing if I enable WIFI and connect to some network it reboot and is not able to boot again. Always reboot at Welcome screen. Battery out - wait some time - battery in - booting - extremly fast disable wifi and it works normally.
SO... is my WIFI bricked? Is anything known about that matter. If yes - are there solutions???
Thanks
CRC

really - no one can help me
damned i think my desire has a heating problem. everytime i do something little bit intesiver work - like syncing, or inet surfing - my desire does a restart and could only be reachable after 20 min without plugged in battery.
strange

Throughout reading your problems, I immediately thought it was a hardware issue. Talk to HTC and see what they say.
Punched in..

oke i allready thought about something like that
just wanted it to confirm by someone else...
thank u

Similar problem
Hi all,
I have a rooted HTC Desire that is stuck in a bootloop. It gets to the HTC screen and that’s it. I tried to upgrade from a cyanogen MOD 7 to gingerbread 2.3 with the RUU I got from the HTC DEV site. Well actually the upgrade looked to be succesfull but when my phone rebooted I got this bootloop.
So now I tried to do a recovery but I only get the “apply update from sdcard” instead of “apply sdcard:update.zip”. When I try to do this update I get a “invalid operation” and the phone reboots. I also did a wipe of the cache and data.
When I try and connect with usb I can only see a driver being loaded after I switch to fastboot.
I tried “adb devices” but no device is seen. When I do the “fastboot devices” I get a serial.
I also tried the Revolutionary software to S-OFF but again I get the “waiting for device”. I tried with the HTC sync drivers, bootloader drivers with several laptops and pc’s.
BRAVO PVT3 SHIP S-ON
HBOOT-1.02.0001
MICROP-051d
TOUCH PANEL-SYNT0101
RADIO-5.17.05.23
I also tried with an other sdcard from a working Desire but I cannot get on the sdcard.
I tried to “mount” the sdcard again with 'fastboot oem enableqxdm 0' but no luck.
Please ask if more info is needed.

Deeway666 said:
Hi all,
I have a rooted HTC Desire that is stuck in a bootloop. It gets to the HTC screen and that’s it. I tried to upgrade from a cyanogen MOD 7 to gingerbread 2.3 with the RUU I got from the HTC DEV site. Well actually the upgrade looked to be succesfull but when my phone rebooted I got this bootloop.
So now I tried to do a recovery but I only get the “apply update from sdcard” instead of “apply sdcard:update.zip”. When I try to do this update I get a “invalid operation” and the phone reboots. I also did a wipe of the cache and data.
When I try and connect with usb I can only see a driver being loaded after I switch to fastboot.
I tried “adb devices” but no device is seen. When I do the “fastboot devices” I get a serial.
I also tried the Revolutionary software to S-OFF but again I get the “waiting for device”. I tried with the HTC sync drivers, bootloader drivers with several laptops and pc’s.
BRAVO PVT3 SHIP S-ON
HBOOT-1.02.0001
MICROP-051d
TOUCH PANEL-SYNT0101
RADIO-5.17.05.23
I also tried with an other sdcard from a working Desire but I cannot get on the sdcard.
I tried to “mount” the sdcard again with 'fastboot oem enableqxdm 0' but no luck.
Please ask if more info is needed.
Click to expand...
Click to collapse
Stuck with exactly the same problem, Devs Please help!

Can't root a RUU Bravo version 2.10.751.4

Hi,
Let me start with my device info.
HTC Desire
- Bravo PVT4 SHIP S-ON
- HBOOT-0.93.0001
- MICROP-051d
- Touch panel-synw0101
- radio-5.09.05.30_2
- Aug 10 2010,17;52;18
Current image version
RUU_Bravo_Froyo_Chunghwa Taiwan carriers (version: 2.10.751.4)
I'm running Windows Vista x86
That's all I got.
Now, the problem.
Everytime I turn the device on, it get stuck at the White HTC Windows and vibrates several times, I think this is a pretty common problem, so I won't stress this issue too much.
The solutions that I found are.
As my device is S-ON my options are limited. I can't boot recovery, so..
I download the latest RUU_Bravo_Froyo_HTC_WWE_2_29_405_5_Radio_32_49_00_32U_5_11_05_27_release_159811_signed_2
Now, I run the ruu until ask to connect, I connect my device, the ruu recognize and identify my device, it ask to update, everything good. Updating process start and suddenly stops and tells me, "error 131, customer id error"
and that I need to use the right RUU utility.?
So I decided to avoid the USB connection and try to flash it directly from the SDCARD, I extracted the rom.zip from the above file, change the name to PB99IMG.ZIP, put it on my device, volume + power, but nothing.
so thinking that something is missing, I select fast boot, the device shows some text in green, even shows the PB99IMG.ZIP file, and is back to the bootloader screen and nothing happens.
What else can I do to bring to life my device, if I choose recovery with the PB99IMG file in the sdcard, the device shows a black screen with a red triangle.
I think is something with that taiwanes RUU, but maybe not.
Could any one please put me in the right direction
Thanks in advance
Sovius

As my device is S-ON my options are limited. I can't boot recovery, so..
Click to expand...
Click to collapse
Can you boot into fastboot? Using revolutionary.io will give you S-OFF and then you can flash a recovery - since you are PVT4, then AmonRa or newest CWM recommended.

You need a goldcard to RUU with that RUU. Download the 2.3.3 RUU from htcdev.com. this should resolve the Id issue.
Sent from my HTC Desire using xda premium

Thanks for you replays
This is what happen now.
davebugyi
In tried to S-Off with Revolutionary, I remove HTC Sync and install the drivers required. > Back + Power > the device is in fastboot screen > connect the USB cable and the device seems to be recognized by the computer but no notification of that is given, except for a beep (like when you plug a USB flashdrive) but no letter is assign to the device or anything. > I double click revolutionary and the program said "waiting for device", I left it for 30min, but nothing.
As I cannot get inside the device, the problem might be that revolutionary requires my device to have "USB debugging on" I don't know if is on or not.
rootSU
How do I create a Gold Card, if I can't get inside the device to set everything up?. Can I use another Gold card or they are exclusive of each device.?.
Your recommendation are Welcome, Please let me know if you need anything from me to have a much clear understanding about what's going on.
I'll make a video to show you exactly what happening and what I'm doing
Cheers

[Q] Stuck in hboot at flashing stock recovery.

In advance, thank you for any assistance.
I have a VZW Dinc 2 Rooted with Revolutionary
Vivo_W XB Ship S-Off RL
HBOOT-6.13.1002
Radio-1.09.01.0622
emmc-boot
Apr 1 2011, 18:34:39
To make a long story short, the Dinc is stuck at the Hboot screen. How it got there, not quite sure. Wasn't my phone and am trying to fix it for a friend.
I have a tested working SD card, and tested working USB cable. The phone, when power is pressed - boots to the white HTC screen, then goes blank/black. The phone can get to the bootloader by vol+&power, but when accessing recovery choice, again, white HTC screen then blank/black. I've tried flashing stock with pg32img.zip, but it hangs on recovery (30+ min).
I've tried connecting to PC, and the drivers are properly installed, HTC sync is removed and the device is seen by fastboot; but not adb. In fastboot, regardless of the command, I get an error. Again, any ideas and assistance are welcome.
Thank you,

jakekam1 said:
In advance, thank you for any assistance.
I have a VZW Dinc 2 Rooted with Revolutionary
Vivo_W XB Ship S-Off RL
HBOOT-6.13.1002
Radio-1.09.01.0622
emmc-boot
Apr 1 2011, 18:34:39
To make a long story short, the Dinc is stuck at the Hboot screen. How it got there, not quite sure. Wasn't my phone and am trying to fix it for a friend.
I have a tested working SD card, and tested working USB cable. The phone, when power is pressed - boots to the white HTC screen, then goes blank/black. The phone can get to the bootloader by vol+&power, but when accessing recovery choice, again, white HTC screen then blank/black. I've tried flashing stock with pg32img.zip, but it hangs on recovery (30+ min).
I've tried connecting to PC, and the drivers are properly installed, HTC sync is removed and the device is seen by fastboot; but not adb. In fastboot, regardless of the command, I get an error. Again, any ideas and assistance are welcome.
Thank you,
Click to expand...
Click to collapse
I am having the same problem today and need help ASAP since this is my only device. Im stuck on the revolutionary exe cmd where it says waiting for fastboot while the phone is stuck on the boot loader.

Guys please post the error message. Need more info.
fastboot devices should show as follows.