I compiled ext4 module to work with enclair 2.1 kernel 2.6.29, tested with XXJF5 stock firmware. Need root access, tune2fs and mke2fs static binary (e2fsprog-bin.tgz.zip)
mkdir -p /system/lib/modules/2.6.29/
#copy module.tar.gz in /system/lib/modules/2.6.29/
cd /system/lib/modules/2.6.29/
tar zxvf module.tar.gz
insmod /system/lib/modules/2.6.29/kernel/fs/jbd2/jbd2.ko
insmod /system/lib/modules/2.6.29/kernel/lib/crc16.ko
insmod /system/lib/modules/2.6.29/kernel/fs/ext4/ext4.ko
if=/dev/zero of=/sdcard/sd/filesystem.ext4 bs=1048576 count=2048
losetup /dev/block/loop1 /sdcard/sd/filesystem.ext4
mke2fs -t ex4 /dev/block/loop1
tune2fs -c 0 -i 0 -m 0 /dev/block/loop1
mkdir /sdcard/sddata
mount -t ext4 /dev/block/loop1 /sdcard/sddata
cp -rp /data/data /sdcard/sddata
cp -rp /data/system /sdcard/sddata
cp -rp /data/dalvik-cache /sdcard/sddata
cp -rp /data/app /sdcard/sddata
cp -rp /data/app-private /sdcard/sddata
mount -t ext4 -o bind /sdcard/sddata/data /data/data
mount -t ext4 -o bind /sdcard/sddata/system /data/system
mount -t ext4 -o bind /sdcard/sddata/dalvik-cache /data/dalvik-cache
mount -t ext4 -o bind /sdcard/sddata/app /data/app
mount -t ext4 -o bind /sdcard/sddata/app-private /data/app-private
run your quadrant test, i got 1793. enjoy.
ps: if you want make it permanent look at RyanZA playlogos1 trick. Also make sure your ext4 filesystem is available at boot time instead /sdcard/sddata
Note:
- due its nature ext4 keep data in RAM much more than ext3 before writing on disk, therefore if a powerloss happens before data got written this may results in lost of data. (see delayed allocation). On the other hand a temporary file wont be written to disk, but kept on RAM avoiding read/write cycles. Inode reservation can increase performance as well.
- barrier can be disabled but this may result in a corrupt journal
explain please
you may want to use ext4 without reflash, and at the same time keep your /data untouchable, just in case you need a recovery backup. eg: if /sdcard got corrupt, system will mount your original /data. (desynced)
I had to disable vold, and mv /etc/vold.conf /etc/vold.old, otherwise it coundnt find /sdcard/filesystem.ext4 so I mount it just before everything.
userinit.sh
--
/system/bin/mount -t vfat -o errors=remount-ro /dev/block/mmcblk1p1 /sdcard
insmod /system/lib/modules/2.6.29/kernel/fs/jbd2/jbd2.ko
insmod /system/lib/modules/2.6.29/kernel/lib/crc16.ko
insmod /system/lib/modules/2.6.29/kernel/fs/ext4/ext4.ko
/data/local/bin/losetup /dev/block/loop1 /sdcard/filesystem.ext4
/system/xbin/e2fsck -p /dev/block/loop1
/system/bin/mount -t ext4 /dev/block/loop1 /sdcard/sddata
/system/bin/mount -t ext4 -o bind /sdcard/sddata/data /data/data
/system/bin/mount -t ext4 -o bind /sdcard/sddata/system /data/system
/system/bin/mount -t ext4 -o bind /sdcard/sddata/dalvik-cache /data/dalvik-cache
/system/bin/mount -t ext4 -o bind /sdcard/sddata/app /data/app
/system/bin/mount -t ext4 -o bind /sdcard/sddata/app-private /data/app-private
--
mv /system/bin/playlogos1 /system/bin/playlogosnow
Do not forget to create /system/bin/playlogos1 as follow:
#!/system/bin/sh
sh /system/bin/userinit.sh
/system/bin/playlogosnow
I got 1858
this is just proof do not use on your device if you dont know what you doing. Since vold does not mount partition some application may not recognize /sdcard mounted that way.
id like to find a way to start vold before playlogos1 and resolve this issue, buts vold seems check argv[0] before start.
e2fsprogs recompiled as well ? In other words, will the e2fsprogs from cynogen work on ext4? These do use libs, btw.
I might build support for this into CFLagFix if I can freely use the files
yeah static bin.
husq510 said:
yeah static bin.
Click to expand...
Click to collapse
Just want to ask if it's ok to implament this in my lagfix zips
Ofc ill credit you
sure you can.
Thanks for the statically linked e2fsck
Nvm got it working on captivate also
I am a fresh owner Tf300.
It annoyed me that he sees Tf300 internal memory as sdcard
and as an external Micro SD card.
I searched and znalałem Script of SG3.
Modified it - it works.
But there is a problem.
Micro SD card is mounted as sdcard
but the internal (the old SDcard) will not mount)
Maybe someone can help
Because he wants to improve both were mounted partitions correctly
script base from galaxys3 http://forum.xda-developers.com/showthread.php?t=1772234
KOD:
#!/system/bin/sh
# Wait for the system to mount the internal media and remout it as r/o
# this should prevent the system from writing to it until we make the
# switch, yet keeps the /data/media r/w, so at the end it won't be r/o
for i in $(seq 1 1 3000)
do
if ( grep -c "/storage/sdcard0" /proc/mounts ); then
mount -o remount,ro /storage/sdcard0
break;
fi
usleep 100000
done
# now wait for the external media and remount
for i in $(seq 1 1 3000)
do
if ( grep -c "/Removable/MicroSD" /proc/mounts ); then
# create new temporary mount point
mount -o remount,rw /
mkdir /storage/tmpmnt
mount -o remount,ro /
# do the rebinding using the temporary mount point
mount -o bind /data/media /storage/tmpmnt
mount -o bind /Removable/MicroSD /storage/sdcard0
mount -o bind /Removable/MicroSD /data/media
umount /Removable/MicroSD
mount -o bind /storage/tmpmnt /storage/MicroSD
umount /storage/tmpmnt
# make bind for ums mode
mkdir -p /storage/MicroSD/sdcard1
touch /storage/MicroSD/.nomedia
mount -o bind /storage/sdcard0 /storage/extSdCard/external_sd/sdcard1
# done
break;
fi
usleep 100000
done
exit
I´m no developer but that´s a start. Hope someone helps.
arcance said:
I am a fresh owner Tf300.
It annoyed me that he sees Tf300 internal memory as sdcard
and as an external Micro SD card.
I searched and znalałem Script of SG3.
Modified it - it works.
Click to expand...
Click to collapse
Trochę Polskiego się tu wkradło
Please change word "znalazłem" to "found"
It works for me after I modified it and install the latest busybox v1.21.0. ( I'm using Energy ROM 4.1.1 btw). Let me know if this works for you.
Here's the script ( I also attach the flashable zip) :
#!/system/bin/sh
# Wait for the system to mount the internal media and remout it as r/o
# this should prevent the system from writing to it until we make the
# switch, yet keeps the /data/media r/w, so at the end it won't be r/o
for i in $(seq 1 1 3000)
do
if ( grep -c "/storage/sdcard0" /proc/mounts ); then
mount -o remount,ro /storage/sdcard0
break;
fi
usleep 100000
done
# now wait for the external media and remount
for i in $(seq 1 1 3000)
do
if ( grep -c "/Removable/MicroSD" /proc/mounts ); then
# create new temporary mount point
mount -o remount,rw /
mkdir /storage/tmpmnt
mount -o remount,ro /
# do the rebinding using the temporary mount point
mount -o bind /data/media /storage/tmpmnt
mount -o bind /Removable/MicroSD /storage/sdcard0
mount -o bind /Removable/MicroSD /data/media
umount /Removable/MicroSD
mount -o bind /storage/tmpmnt /Removable/MicroSD
umount /storage/tmpmnt
# make bind for ums mode
mkdir -p /Removable/MicroSD/EXTERNAL_SD
touch /Removable/MicroSD/ EXTERNAL_SD/.nomedia
mount -o bind /storage/sdcard0 /Removable/MicroSD/EXTERNAL_SD
# done
break;
fi
usleep 100000
done
exit
Odp: [DEV] SCRIPT MOD inte2ext swap
Ok trying thanx for help
Sent from my HTC Desire Z using xda app-developers app
One question. Will this script solve the I/O problem, as now the tablet will use my class10 sdcard as internal, or didn't I understand it well?
why not just edit the vold file
Sent From My Unlocked & Rooted 4.2.2 Android Powered []D [] []V[] []D TF300T
Works
I think good solution for people ho heve only 16gb internal and sdmicro 64gb or biger
Edit vold ithink no god solution and not be save
Regards
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
arcance said:
Works
I think good solution for people ho heve only 16gb internal and sdmicro 64gb or biger
Edit vold ithink no god solution and not be save
Regards
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
Click to expand...
Click to collapse
you can edit the vold file and accomplish the same results. you need to use a root explorer.I have done it on every device I own at one point.yes it saves.
Hi
Trying use modification
When try flesh i see error can't find tmpmnt
I don't have idea
Use 4.2 xcromi 4.7.0
And need more space for instal soft my tf300 have 16gb only.
Or sugestion how modyfication vold.
Reagarts
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
Hi,
I have a Samsung Galaxy Note 2 (SGH-T889). I found a script online which had instruction to execute with script manager (SManager). The file is called app2sdNote2.bin. When I run SManager and located the script, I select Su and Boot. When I select Run, SManager just hangs forever until I kill the process. The grant message never appears. I would like to run the script to use my 64 GB memory card as the default storage. Any help is greatly appreciated.
#!/system/bin/sh
#extsd2internalsd is a modification that allows to switch internal sd to external sd and viceversa. With this you can use default internal sd only for app storage #and the external sd to store all apps resource and all others stuff. The resut is a very big increase of installable apps on gs3
#All credits to Mattiadj of xda forum for the idea and script and to mike1986 for the cmw zip.
#xda thread url at
#Script Modified for U.S. Galaxy S3/Note 2 by Zedomax at GalaxyS3Root.com and GalaxyNote2Root.com to be compatible when sdcard is not inserted.
busybox mount -o remount,rw /
busybox mount -t vfat -o umask=0000 /dev/block/vold/179:17 /mnt/sdcard
busybox mount -t exfat -o umask=0000 /dev/block/vold/179:17 /mnt/sdcard
if busybox mount | busybox grep vold/179:17; then
busybox mount -o bind /data/media /mnt/extSdCard
fi
comicrage said:
Hi,
I have a Samsung Galaxy Note 2 (SGH-T889). I found a script online which had instruction to execute with script manager (SManager). The file is called app2sdNote2.bin. When I run SManager and located the script, I select Su and Boot. When I select Run, SManager just hangs forever until I kill the process. The grant message never appears. I would like to run the script to use my 64 GB memory card as the default storage. Any help is greatly appreciated.
#!/system/bin/sh
#extsd2internalsd is a modification that allows to switch internal sd to external sd and viceversa. With this you can use default internal sd only for app storage #and the external sd to store all apps resource and all others stuff. The resut is a very big increase of installable apps on gs3
#All credits to Mattiadj of xda forum for the idea and script and to mike1986 for the cmw zip.
#xda thread url at
#Script Modified for U.S. Galaxy S3/Note 2 by Zedomax at GalaxyS3Root.com and GalaxyNote2Root.com to be compatible when sdcard is not inserted.
busybox mount -o remount,rw /
busybox mount -t vfat -o umask=0000 /dev/block/vold/179:17 /mnt/sdcard
busybox mount -t exfat -o umask=0000 /dev/block/vold/179:17 /mnt/sdcard
if busybox mount | busybox grep vold/179:17; then
busybox mount -o bind /data/media /mnt/extSdCard
fi
Click to expand...
Click to collapse
Wrong device thread.
comicrage said:
Hi,
I have a Samsung Galaxy Note 2 (SGH-T889). I found a script online which had instruction to execute with script manager (SManager). The file is called app2sdNote2.bin. When I run SManager and located the script, I select Su and Boot. When I select Run, SManager just hangs forever until I kill the process. The grant message never appears. I would like to run the script to use my 64 GB memory card as the default storage. Any help is greatly appreciated.
#!/system/bin/sh
#extsd2internalsd is a modification that allows to switch internal sd to external sd and viceversa. With this you can use default internal sd only for app storage #and the external sd to store all apps resource and all others stuff. The resut is a very big increase of installable apps on gs3
#All credits to Mattiadj of xda forum for the idea and script and to mike1986 for the cmw zip.
#xda thread url at
#Script Modified for U.S. Galaxy S3/Note 2 by Zedomax at GalaxyS3Root.com and GalaxyNote2Root.com to be compatible when sdcard is not inserted.
busybox mount -o remount,rw /
busybox mount -t vfat -o umask=0000 /dev/block/vold/179:17 /mnt/sdcard
busybox mount -t exfat -o umask=0000 /dev/block/vold/179:17 /mnt/sdcard
if busybox mount | busybox grep vold/179:17; then
busybox mount -o bind /data/media /mnt/extSdCard
fi
Click to expand...
Click to collapse
Script doesn't work on s4. Tried all the known scripts and so far none work.
Sent from my SGH-M919 using Tapatalk 2
WORD OF WARNING: if you do this, wiping /data from recovery will not actually wipe data. AND if you install a new ROM, via clean or dirty flash, chances are your large /data partition will go all screwy on you. It did for me. If I flashed anything, it tends to cause boot loops or hangs at the boot animation.
If you are dirty flashing anything, I would first get as much off of the large /data as you can to get it to 2 GB or less, then drop it on top of your 2 GB /data partition, then dirty flash, let everything come back up and get stable then repeat these steps starting at step 2 to blow away your large /data and then mirror your 2 GB /data to your large /data.
The problems I had could be related to xposed, but I am not 100% certain on this. It is my best guess from looking at my logcat (doesn't actually indicate a crash in there, but has a lot of stuff related to xposed).
These steps are more for the non-flashaholics amung us OR people who flash new stuff but roll back to nandroid. Once you pop the larger /data onto any ROM, your nandroid will likely not play nice with it anymore as your larger /data is not restored from a nandroid.
And the normal "warranty is now void" and "if things break, it isn't my fault" disclamer stuff too. But I'm running this right now and liking it (except when I go to jump to KK it may not be happy with me... gonna need to do some testing to nandroids work properly AND so I can flash ROMs without blowing everything up... thinking it is just the dalvik that is unhappy, but I am uncertain at this time)
I was having issues with my /data partition getting full on me after getting new ROMs set up. This was irritating me and I came to the conclusion that 2 GB was just not enough space for some of the larger apps out there. So I went ahead and started investigating and testing how to get /data onto the external SD card.
2 complications arise:
1) it needs to be in ext4 format to preserve permissions
2) it needs to be swapped post boot AFTER the sd card is mounted (potentially, I have not fully tested this).
So this becomes a multi step process. What you need:
1) an external SD card that is at least 2 GB in size if not larger (I recommend larger simply because what is the point of having it on external storage if you aren't gaining any extra space)
2) a SGH-T989D (I do not have an SGH-T989 to test it with BUT I am confident it will work with that one too)
3) some partitioning software on your PC (I recommend EaseUS or AOMEI, but use whatever you are comforatble with)
4) latest version of busybox installed on your phone
So, the steps to do this:
1) partition your external SD card into at least 2 partitions, where your second partition will be used for /data. The first partition automatically mounts to /storage/sdcard1, but partition 2 will NOT auto-mount. You do not need to format this if you do not want to. This is up to you how you do it.
2) Run the following commands from either adb shell OR android terminal:
su
mke2fs /dev/block/mmcblk1p2
mkdir /storage/sdcard1/PARTITION2
mount -t ext4 /dev/block/mmcblk1p2 /storage/sdcard1/PARTITION2
rsync -HpogEvrl /data/* /storage/sdcard1/PARTITION2
busybox umount -l /storage/sdcard1/PARTITION2
mount -o remount,errors=continue /data
busybox umount -l /data && mount -t ext4 -o rw,seclabel,errors=continue,user_xattr,acl,barrier=1,data=ordered,noauto_da_alloc /dev/block/mmcblk1p2 /data
chown system:system /data
restorecon /data
brief explaination of the above commands:
su - switch user to root
mke2fs - format the block device as ext4
mkdir - make directory
mount -t ext4 - mount a block device of type ext4 from /dev/block/mmcblk1p2 to /storage/sdcard1/PARTITION2
rsync -HpogEvrl - copy files from /data/* to /storage/sdcard1/PARTITION2 preserving all attributes (including owner and group)
busybox umount -l - use the busybox version of umount to do a lazy unmount of /storage/sdcard1/PARTITION2. this will unmount it even if files are locking it
mount -o remount,errors=continue /data - remounts the data partition telling it to continue instead of kernel panic if there is any errors reading or writing to that mount point
and the next command is actually 2:
busybox umount -l /data && mount -t ext4 -o rw,seclabel,errors=continue,user_xattr,acl,barrier=1,data=ordered,noauto_da_alloc /dev/block/mmcblk1p2 /data
this does a lazy unmount of /data and then mounts /dev/block/mmcblk1p2 to /data with the appropriate parameters for the /data parameter
chown system:system /data - This gives system ownership of /data instead of root as is originally done
restorecon /data - we do this just in case the userdata partition has been reset.
3) OPTIONAL delete the directory /storage/sdcard1/PARTITION2. This is just cleanup, it is not neccessary to do.
When you reboot your phone, your /data directory will remount to the 2 GB partition as it did originally. To remount it to your newly created /data partition, run the following 2 commands:
su
busybox umount -l /data && mount -t ext4 -o rw,seclabel,errors=continue,user_xattr,acl,barrier=1,data=ordered,noauto_da_alloc /dev/block/mmcblk1p2 /data
Now, you can make this into a nice and easy startup script by following these simple steps from adb shell or android terminal (NOTE this assumes that your ROM supports userinit.d and init.d):
su
cd /data/local/userinit.d
echo "#!/system/bin/bash" > dataswap
echo "if [ -e \"/dev/block/mmcblk1p2\" ]" >>dataswap
echo "then" >> dataswap
echo "busybox umount -l /data && mount -t ext4 -o rw,seclabel,errors=continue,user_xattr,acl,barrier=1,data=ordered,noauto_da_alloc /dev/block/mmcblk1p2 /data" >> dataswap
echo "chown system:system /data" >> dataswap
echo "restorecon /data" >> dataswap
echo "fi" >>dataswap
chown root:shell dataswap
chmod 777 dataswap
and now when you reboot your phone you will have your external SD cards partition 2 as your /data directory.
If your phone has init.d support, look in your /system/etc/init.d folder for a script named "90userinit". If it is not there, you will need to either make it and have it run userinit.d OR change the line:
cd /data/local/userinit.d
to
cd /system/etc/init.d
mount -o remount,rw /system
now for the warning stuff:
1) I strongly recommend that you do NOT put this into your /data/local/userinit.d folder until you are 110% certain that it worked on your device with your ROM. The reason for this is if it fails and you don't have it in that folder, simply reboot and your phone is back to using /data from partition 25 on your internal memory
2) I strongly recommend you do a nandroid before you begin. That way in the very slim chance that something goes horridly wrong, you can recover
3) I strongly recommend you back up your external SD card before you begin resizing your partitions. Resizing partitions may result in data loss.
4)I take no responsibility for any data loss
5) I have ONLY tested this on a SGH-T989D running HellyBean (Android 4.3). I cannot make any comments on other ROMS, but as long as the ROM has busybox, root, and init.d support, this should work.
6) If you get ANY ERRORS from ANY of the above commands, stop everything and either post in this thread or start over. I have done this twice on my phone to make sure that the steps are as solid as I know how to make them. The only thing I haven't fully tested is putting it into a startup script.
One thing I notice, sometimes when you unmount and remount /data, any data changes in your currently running apps (ie you get a text message while doing this or you start a game up while /data is being sync'ed) may cause odd data issues when the two swap and may cause your phone to jump back to the boot animation. If this occurs, try waiting approximately 1 minute OR until adb shell drops out; whatever comes first. At that point, something has likely gone sour. Reboot your phone and things will be back how they were prior to step 2 (step 1 is permanent until you change that).
Questions, comments, suggestions? Please leave them in the thread, not in PM. If I get any PM's about this thread, I'll do my best to answer, but I may end up posting your PM in this thread to help others.
EDIT: cleaned up the instructions a little and added in some recommended steps (the chown and restorecon) and removed the waiting to mount /data as that just makes things unhappy long term.
EDIT: added error handling in case mmcblk1p2 does not exist to the startup script. If it does not exist, it will now NOT swap the partitions. So as a failsafe, if your phone gets stuck at the boot animation, you can power it down, remove the SD card and power it back up to boot with your default /data partition. This should not need to be done, but there is a chance that your SD card could die or your new /data partition get corrupted, this will allow you to recover safely and will likely only require you to re-create your data partition and NOT have to re-do your whole ROM due to something going bad on the big /data.
Dang...found a bug: it looks like if you leave it for a few days or reboot our something(have not narrowed it down yet) some apps stop working... investigating it and should have a solution sometime tonight... sorry to all those who have tried this... if you have not done much, I'd suggest switching back to normal /data until I get the bug sorted out. My best guess is that reboot doesn't unmount the partition cleanly but I'm not positive...
bmg002 said:
I was having issues with my /data partition getting full on me after getting new ROMs set up. This was irritating me and I came to the conclusion that 2 GB was just not enough space for some of the larger apps out there. So I went ahead and started investigating and testing how to get /data onto the external SD card.
2 complications arise:
1) it needs to be in ext4 format to preserve permissions
2) it needs to be swapped post boot AFTER the sd card is mounted (potentially, I have not fully tested this).
So this becomes a multi step process. What you need:
1) an external SD card that is at least 2 GB in size if not larger (I recommend larger simply because what is the point of having it on external storage if you aren't gaining any extra space)
2) a SGH-T989D (I do not have an SGH-T989 to test it with BUT I am confident it will work with that one too)
3) some partitioning software on your PC (I recommend EaseUS or AOMEI, but use whatever you are comforatble with)
4) latest version of busybox installed on your phone
So, the steps to do this:
1) partition your external SD card into at least 2 partitions, where your second partition will be used for /data. The first partition automatically mounts to /storage/sdcard1, but partition 2 will NOT auto-mount. You do not need to format this if you do not want to. This is up to you how you do it.
2) Run the following commands from either adb shell OR android terminal:
su
mke2fs /dev/block/mmcblk1p2
mkdir /storage/sdcard1/PARTITION2
mount -t ext4 /dev/block/mmcblk1p2 /storage/sdcard1/PARTITION2
rsync -HpogEvrl /data/* /storage/sdcard1/PARTITION2
busybox umount -l /storage/sdcard1/PARTITION2
mount -o remount,errors=continue /data
busybox umount -l /data && mount -t ext4 -o rw,seclabel,errors=continue,user_xattr,acl,barrier=1,data=ordered,noauto_da_alloc /dev/block/mmcblk1p2 /data
brief explaination of the above commands:
su - switch user to root
mke2fs - format the block device as ext4
mkdir - make directory
mount -t ext4 - mount a block device of type ext4 from /dev/block/mmcblk1p2 to /storage/sdcard1/PARTITION2
rsync -HpogEvrl - copy files from /data/* to /storage/sdcard1/PARTITION2 preserving all attributes (including owner and group)
busybox umount -l - use the busybox version of umount to do a lazy unmount of /storage/sdcard1/PARTITION2. this will unmount it even if files are locking it
mount -o remount,errors=continue /data - remounts the data partition telling it to continue instead of kernel panic if there is any errors reading or writing to that mount point
and the last command is actually 2:
busybox umount -l /data && mount -t ext4 -o rw,seclabel,errors=continue,user_xattr,acl,barrier=1,data=ordered,noauto_da_alloc /dev/block/mmcblk1p2 /data
this does a lazy unmount of /data and then mounts /dev/block/mmcblk1p2 to /data with the appropriate parameters for the /data parameter
3) OPTIONAL delete the directory /storage/sdcard1/PARTITION2. This is just cleanup, it is not neccessary to do.
When you reboot your phone, your /data directory will remount to the 2 GB partition as it did originally. To remount it to your newly created /data partition, run the following 2 commands:
su
busybox umount -l /data && mount -t ext4 -o rw,seclabel,errors=continue,user_xattr,acl,barrier=1,data=ordered,noauto_da_alloc /dev/block/mmcblk1p2 /data
Now, you can make this into a nice and easy startup script by following these simple steps from adb shell or android terminal (NOTE this assumes that your ROM supports userinit.d and init.d):
su
cd /data/local/userinit.d
echo "#/sys/bin/bash" > dataswap.sh
echo "while [ \`mount | grep -c sdcard\` -lt 3 ]" >> dataswap.sh
echo "do" >> dataswap.sh
echo "sleep 10" >> dataswap.sh
echo "done" >> dataswap.sh
echo "busybox umount -l /data && mount -t ext4 -o rw,seclabel,errors=continue,user_xattr,acl,barrier=1,data=ordered,noauto_da_alloc /dev/block/mmcblk1p2 /data" >> dataswap.sh
chown root:shell dataswap.sh
chmod 777 dataswap.sh
and now when you reboot your phone you will have your external SD cards partition 2 as your /data directory.
If your phone has init.d support, look in your /system/etc/init.d folder for a script named "90userinit". If it is not there, you will need to either make it and have it run userinit.d OR change the line:
cd /data/local/userinit.d
to
cd /system/etc/init.d
mount -o remount,rw /system
now for the warning stuff:
1) I strongly recommend that you do NOT put this into your /data/local/userinit.d folder until you are 110% certain that it worked on your device with your ROM. The reason for this is if it fails and you don't have it in that folder, simply reboot and your phone is back to using /data from partition 25 on your internal memory
2) I strongly recommend you do a nandroid before you begin. That way in the very slim chance that something goes horridly wrong, you can recover
3) I strongly recommend you back up your external SD card before you begin resizing your partitions. Resizing partitions may result in data loss.
4)I take no responsibility for any data loss
5) I have ONLY tested this on a SGH-T989D running HellyBean (Android 4.3). I cannot make any comments on other ROMS, but as long as the ROM has busybox, root, and init.d support, this should work.
6) If you get ANY ERRORS from ANY of the above commands, stop everything and either post in this thread or start over. I have done this twice on my phone to make sure that the steps are as solid as I know how to make them. The only thing I haven't fully tested is putting it into a startup script.
One thing I notice, sometimes when you unmount and remount /data, any data changes in your currently running apps (ie you get a text message while doing this or you start a game up while /data is being sync'ed) may cause odd data issues when the two swap and may cause your phone to jump back to the boot animation. If this occurs, try waiting approximately 1 minute OR until adb shell drops out; whatever comes first. At that point, something has likely gone sour. Reboot your phone and things will be back how they were prior to step 2 (step 1 is permanent until you change that).
Questions, comments, suggestions? Please leave them in the thread, not in PM. If I get any PM's about this thread, I'll do my best to answer, but I may end up posting your PM in this thread to help others.
Click to expand...
Click to collapse
So found a solution to crashing apps . Load up the play store and update your apps. Worked for me anyways.
Now to fix a potential mounting bug in the op, put any scripts on a different ext4 position such as/system/xbin or/system/etc/init.d.
I'll keep you posted if I find other bugs.
Sent from my SAMSUNG-SGH-T989 using xda app-developers app
Bleh new bug:
When you unplug it from a pc, it gets confused and you get io errors which cause it to crash back to the boot animation and get stuck there... too tired to debug out tonight but I'll poke at it tomorrow... thinking I may need to build a kernel module for this... or a custom kernel
Sent from my SAMSUNG-SGH-T989 using xda app-developers app
So the unplugging issue seems quite intermittent and I am unable to get consistent results with it. So I am not sure if it is a bug or not. I updated the OP to have error handling so you can pull your SD card out to mount the 2 GB /data that your phone normally does instead of your big one in the event that something goes wrong.
Hrm... so my testing and further development with this has taken a temporary pause due to my SD card dying on me. Stupid SD card... haven't even had it a year. Hoping I can find the reciept. But once I get it replaced, I'll be jumping in on this some more. I have a few cool ideas that we can do by moving partitions to external storage...
What's the deal with cause this would so help with games but is it possible to maybe if possible extend the internal storage
snt? from? sumthiN 4.4+ ?via a ?T989
hatememarkz said:
What's the deal with cause this would so help with games but is it possible to maybe if possible extend the internal storage
snt? from? sumthiN 4.4+ ?via a ?T989
Click to expand...
Click to collapse
From my testing it seems to work but puts a heavy load the sd card. And if your sd card fails you will lose some data.
I have not tested this on KitKat yet but that is my plan soon.
Sent from my SM-T310 using xda app-developers app
Was using Link2SD to move apps to the second partition of a micro SD card for the usual reasons... Then did -something- that broke the micro SD card slot. Now what to do?
Possible solutions:
Is it possible to repartition the internal NAND? -- Wouldn't that involve unpacking and repacking the kernel image? Better not... Although it was an inexpensive tablet, it would be an expensive brick.
Is it possible to bind-mount a directory on the "internal SD" for use with Link2SD? -- Would that even work with vfat? (Permissions and stuff...)
What about replacing the ext2 SD-card partition with a disk image
Materials:
Android tablet. (Broken SD card slot optional.)
Root with busybox installed.
Link2SD installed and configured -- This has to be done prior to breaking the SD card slot. Link2SD's startup scripts are needed, which it may not create without a "properly" formatted and installed SD card.
Computer with Linux installed OR a Linux Live DVD -- To create the disk image and transfer the contents from the physical SD card to the image file. I used Ubuntu.
USB transfer cable (optional) -- To transfer the disk image from the computer to the tablet. Also to execute terminal commands on the tablet. Possible to do over a network, but the cable can be faster and more convenient.
Do not try this unless you are fully prepared to brick your device.
Method:
Create the disk image on the computer:
Code:
qemu-img create -f raw link2sd-disk.img 3G
Format the disk image to ext2:
Code:
mkfs.ext2 link2sd-disk.img
Mount the disk image to a newly created directory:
Code:
mkdir /tmp/link2sd-disk
sudo mount -o loop link2sd-disk.img /tmp/link2sd-disk
Mount the original SD card with the second ext2 partition.
Copy the contents of the sd card to the disk image. Use rsync to keep file permissions and other metadata. The trailing "/" on the directory names is important.
Code:
sudo -s
rsync --archive --hard-links /media/path-to-sd-card/ /tmp/link2sd-disk/
Unmount the sd card and disk image.
Code:
sudo umount /tmp/link2sd-disk
Transfer the disk image to your tablet.
Code:
adb push link2sd-disk.img /mnt/sdcard/link2sd-disk.img
Edit /system/bin/debuggerd on the tablet:
Code:
adb pull /system/bin/debuggerd
Edit debuggerd with your favorite text editor. Pay careful attention to the actual identity of the internal sd card as used on your tablet (/dev/block/mtdblock9). Notice that "busybox mount" is used. The normal mount command does not support the necessary options.
Code:
#!/system/bin/sh
#added by link2sd
LOG=/data/link2sd-debuggerd.log
ls -la /dev/block/ 1>>$LOG 2>>$LOG
echo 1>>$LOG 2>>$LOG
echo "$(date) mounting..." > $LOG
busybox mount -t vfat -o rw,relatime,uid=1000,gid=1015,fmask=0002,dmask=0002,shortname=mixed,errors=remount-ro /dev/block/mtdblock9 /mnt/sdcard 1>>$LOG 2>>$LOG
busybox mount -t ext2 -o loop,rw /mnt/sdcard/link2sd.img /data/sdext2 1>>$LOG 2>>$LOG
echo 1>>$LOG 2>>$LOG
mount >> $LOG
echo 1>>$LOG 2>>$LOG
echo debuggerd.bin launched >> $LOG
exec /system/bin/debuggerd.bin
Backup the original file and transfer the new file and set permissions.
Code:
adb shell mv /system/bin/debuggerd /system/bin/debuggerd.001
adb push debuggerd /system/bin/debuggerd
adb shell chmod 755 /system/bin/debuggerd
All done. Reboot. :fingers-crossed:
Hope the above is useful or enlightening. Let me know if I need to explain anything in greater detail.
I've tested this on HTC One X and it does not work. After mounting sdcard and my image using these commands:
Code:
busybox mount -t vfat -o rw,relatime,uid=1000,gid=1015,fmask=0002,dmask=0002,shortname=mixed,errors=remount-ro dev/block/vold/179:14 /mnt/sdcard 1>>$LOG 2>>$LOG
busybox mount -t ext2 -o loop,rw /mnt/sdcard/link2sd.img /data/sdext2 1>>$LOG 2>>$LOG
I have access to the image file from /data/sdext2 but my sdcard is not visible in the system (but it is mounted in the /mnt/sdcard). Does anyone know how to mount .img during boot? Binding to debuggerd seems to be not the best option. :S
EDIT BELOW:
I've found a solution to this issue:
1. create 03mountsd file
2. put it in the /etc/init.d/ directory (for example, using adb)
3. reboot
03mountsd contents:
Code:
#!/system/bin/sh
#added by link2sd
LOG=/data/mountsd.log
COUNTER=60
ls -la /dev/block/ 1>>$LOG 2>>$LOG
echo 1>>$LOG 2>>$LOG
echo "$(date) mounting..." > $LOG
while [[ $COUNTER -gt 0 && ! -f /storage/sdcard0/app.img ]]; do
COUNTER=$(($COUNTER-1))
sleep 1
done
echo "=> COUNTER = $COUNTER" > $LOG
# busybox mount -t vfat -o rw,relatime,uid=1000,gid=1015,fmask=0002,dmask=0002,shortname=mixed,errors=remount-ro /dev/block/vold/179:14 /mnt/.sd 1>>$LOG 2>>$LOG
busybox mount -t ext4 -o loop,rw /storage/sdcard0/app.img /data/sdext2 1>>$LOG 2>>$LOG
echo 1>>$LOG 2>>$LOG
mount >> $LOG
echo 1>>$LOG 2>>$LOG
EDIT: still not working: applications moved using link2sd and this method are not visible for android. :/