Develop Bugs

##778 hacks shared

Anyone care to share any usefull hacks after one has obtained their msl?

##778# Hacks
I can't take credit for these, but they work...
Shorten time/ number of rings to answer
Credit to Elkay
Thread
Here is a tip from the 6700 forum that works on the Touch (credit to Elkay in the 6700 forum). You may have noticed that when someone calls you it may take several rings on their end before the Touch begins to ring. The reason for this delay is the “slot cycle index,” or how often your Touch polls the towers for an incoming call. Default appears to be about 5 seconds—way to long. Of course, as always, there is a compromise to be made—the more often it polls the tower, the more power it uses. Anyway here is the hack:
To do this, you will need your MSL number, which only Sprint (or your provider) can provide you.
1) Open up the phone app and dial ##778# (PST).
2) You will be asked to enter your MSL. Enter it, and you will be brought into the provisioning of your phone.
3) From the top left, select Modem Settings. On this page, your Slot Cycle Index (SCI) is how often your phone polls the tower for incoming calls, etc. This value is 1.28 seconds multiplied by 2 (i.e 0=1.28 secs, 1=2.56secs) with 0 fastest, 7 slowest. The default is 2, but lowering it to 1 hasn't noticeably affected my battery life, and roughly 2.5 second (SCI 1) response time is far more reasonable than roughly 5 seconds (SCI 2).
………………………………………………………………………………………………………………………………
………………………………………………………………………………………………………………………………
Force EV-DO/1X, quicker ring response
Same thread
Here is another tip from the same 6700 post by Elkay.
1) Follow steps 1 through 3 in the Shorten time/ number of rings to answer tip:
Also on this page is your preferred operation mode. The Default is Automatic, which is the best available mode (EV that will roll back to 1X when EV is unavailable). There are times when you might be in a fringe area and your mode may cycle frequently and this can seriously drain your battery. Setting this to HDR will force EV-DO only if you demand an EV-DO connection. Changing this setting to CDMA Only will force the phone to ignore an EV-DO tower and maintain only a 1xRTT connection.
Cheers,
DJ

deegimus said:
Also on this page is your preferred operation mode. The Default is Automatic, which is the best available mode (EV that will roll back to 1X when EV is unavailable). There are times when you might be in a fringe area and your mode may cycle frequently and this can seriously drain your battery. Setting this to HDR will force EV-DO only if you demand an EV-DO connection. Changing this setting to CDMA Only will force the phone to ignore an EV-DO tower and maintain only a 1xRTT connection.
DJ
Click to expand...
Click to collapse
Automatic or CDMA or HDR is preferred for Sprint usage?? which is best?

bugzy said:
Automatic or CDMA or HDR is preferred for Sprint usage?? which is best?
Click to expand...
Click to collapse
automatic is best under most circumsatnces.

Automatic works better
i tried the other settings, for some reason, when i call myself on LAN phone, it goes straight to voicemail

Anyone else have a problem when entering the ##778# on the phone dialer? I have been getting random errors (67 and 1012) so i called sprint yesterday to try and resolve them. I was told to type in ##3282# (i think) to enter a service menu. It does nothing.
I press the green talk button to bring up the dialer, type ##778# and nothing hapens. If i press the green talk button again, it attempts to dial ##778#. Anyone care to give me a heads up on something stupid i am missing here? Thanks.
.eric

e_town said:
Anyone else have a problem when entering the ##778# on the phone dialer? I have been getting random errors (67 and 1012) so i called sprint yesterday to try and resolve them. I was told to type in ##3282# (i think) to enter a service menu. It does nothing.
I press the green talk button to bring up the dialer, type ##778# and nothing hapens. If i press the green talk button again, it attempts to dial ##778#. Anyone care to give me a heads up on something stupid i am missing here? Thanks.
.eric
Click to expand...
Click to collapse
i hit ##778# and wait like 1 or 2 secs and the screen changes
do not any buttons ... dont need to call out, just ##778# and let it sit for 1 sec

Tried waiting....nothing. Called tech support, they were baffled, suggested hard reset. *sigh
Time to pull everything off and reset.
.eric

e_town said:
Tried waiting....nothing. Called tech support, they were baffled, suggested hard reset. *sigh
Time to pull everything off and reset.
.eric
Click to expand...
Click to collapse
I had this problem once. Make sure you don't have some sort of custom dialing skin on. These won't let you access special ## codes. Didn't notice that untill l couldn't get a phone activated with a CSR and figured that was the problem.

thehelios said:
I had this problem once. Make sure you don't have some sort of custom dialing skin on. These won't let you access special ## codes. Didn't notice that untill l couldn't get a phone activated with a CSR and figured that was the problem.
Click to expand...
Click to collapse
actually different dialers as well as different radios wont allow the codes to work right. i always changes the things i need first and then load the goodies on there.

Ill try that. Anything to avoid a hard reset. I have so many little BS apps on this damn thing. Probably good to clean it up anyways.
.eric

thehelios said:
I had this problem once. Make sure you don't have some sort of custom dialing skin on. These won't let you access special ## codes. Didn't notice that untill l couldn't get a phone activated with a CSR and figured that was the problem.
Click to expand...
Click to collapse
Got it fixed. I removed a bunch of programs i had installed. Dont remember which one actually did it, but i had a bunch of UI tweak programs installed. Thanks for the help guys.
.eric

I had the same problem until I found this thread. After removing "EquinoXe Wizard reTOUCHED Dialer" and soft-rebooting, it worked.

## # & error code
or 91 , 94, 71, 1012 errors are Registration/Provisioning errors. You have to contact tech support 1 800 639 6111 to have them re-provision your services. More than likely your PRL check sum ,User name, HA Shared Secret (should always be the word "secret") or your AAA Shared secret (randomly generated by Sprint) is invailid. In any case, they would have to reset on their end.
As far as the ##data# if you dont really know what your changing, I'd do some research first
Sprint Service Tech
Southeastern Div.
Baton Rouge,LA
Have a good day

deegimus said:
1) Open up the phone app and dial ##778# (PST).
2) You will be asked to enter your MSL. Enter it, and you will be brought into the provisioning of your phone.
Click to expand...
Click to collapse
OK, maybe I am the last one to know this but how do I find my MSL code on the Bell Mobility Touch?

You can get the MSL by using a program called GetSPC.
There is a link further down in this post:
http://www.sprintusers.com/forum/showthread.php?t=151852

Do be careful when forcing your phone to use EVDO only -- you won't be able to make/receive any calls or SMS as both of those services require the use of 1xRTT.

is there a way to debrand the sprint htc touch? i'm using it outside the USA!!

deegimus said:
I can't take credit for these, but they work...
Shorten time/ number of rings to answer
Credit to Elkay
Thread
Here is a tip from the 6700 forum that works on the Touch (credit to Elkay in the 6700 forum). You may have noticed that when someone calls you it may take several rings on their end before the Touch begins to ring. The reason for this delay is the “slot cycle index,” or how often your Touch polls the towers for an incoming call. Default appears to be about 5 seconds—way to long. Of course, as always, there is a compromise to be made—the more often it polls the tower, the more power it uses. Anyway here is the hack:
To do this, you will need your MSL number, which only Sprint (or your provider) can provide you.
1) Open up the phone app and dial ##778# (PST).
2) You will be asked to enter your MSL. Enter it, and you will be brought into the provisioning of your phone.
3) From the top left, select Modem Settings. On this page, your Slot Cycle Index (SCI) is how often your phone polls the tower for incoming calls, etc. This value is 1.28 seconds multiplied by 2 (i.e 0=1.28 secs, 1=2.56secs) with 0 fastest, 7 slowest. The default is 2, but lowering it to 1 hasn't noticeably affected my battery life, and roughly 2.5 second (SCI 1) response time is far more reasonable than roughly 5 seconds (SCI 2).
………………………………………………………………………………………………………………………………
………………………………………………………………………………………………………………………………
Force EV-DO/1X, quicker ring response
Same thread
Here is another tip from the same 6700 post by Elkay.
1) Follow steps 1 through 3 in the Shorten time/ number of rings to answer tip:
Also on this page is your preferred operation mode. The Default is Automatic, which is the best available mode (EV that will roll back to 1X when EV is unavailable). There are times when you might be in a fringe area and your mode may cycle frequently and this can seriously drain your battery. Setting this to HDR will force EV-DO only if you demand an EV-DO connection. Changing this setting to CDMA Only will force the phone to ignore an EV-DO tower and maintain only a 1xRTT connection.
Cheers,
DJ
Click to expand...
Click to collapse
How would I find my unlock code ???
Thanks!

bossman74 said:
How would I find my unlock code ???
Thanks!
Click to expand...
Click to collapse
"Unlock"?? You're referring to a CDMA Touch, right (which is why you're in the Vogue forum)? I don't think you can unlock these. Someone correct me if I'm wrong, but the only carriers using CDMA are Sprint and Verizon (in US). If you wanted to use this with a GSM carrier (ATT, T-Mo) you wouldn't be able to regardless of what you do to the phone.
If you are referring to the MSL number, please read the post that you, yourself, quoted.

EVO Up on alltel, little help?

So, Got a sprint EVO for cheap. Sprint had the ESN flagged on sprint network because the owner of the phone's account hasn't been paid. Sold the phone to me, I restored it to factory default, running latest stock 2.2.
Steps taken to get to where I am now:
Used CDMA workshop (licensed 3.5.5) to read the SPC code, rewrote the spc code to 000000. I put an Alltel PRL file on the sd card, same one as my mother's Alltel Hero. Rooted the phone using revoked windows app, replaced the EPST.apk with the older version to allow ##775# (prl change), applied my PRL. Activated the phone on alltel, no problem at all getting it activated.
Call text working great... THEN... using CDMA Workshop, in the EVDO tab (similar function in QPST would be the PPP tab) and entered the HDR user name/pass, in alltel's case, UM is [email protected]/alltel and AN is [email protected]/HEXESN. Set under M.IP to have Simple IP only (read that this will fix the "data call failure" errors) Set profile 0 as active and changed the values to what looks to be the same from the Alltel Hero of my mothers only with my cell number in the fields. Set all nam values such as channels, MCC, etc.. correct, flashed. I then edited the telephony.db to alltel's MMS settings.
Phone's current state, what works, what doesnt..
3G is working great, MMS works perfectly, calling is perfect, SMS is perfect...
1X doesn't work AT ALL:
if I enter an area i KNOW 3G doesn't exist, it doesnt switch to 1X like my eris that i programmed to alltel did, just drops data completely if there's no 3G...
I don't seem to get the Data Call Failure message much at all up until I try to run the "wireless tether" app, it pops up like CRAZY and 3G disconnects every time it pops up.
Phone says I'm roaming constantly, I know I have the latest smartphone PRL for my area and MCC codes etc in the nam are set EXACT to my mothers htc alltel hero and hers doesnt report roaming at all... what gives??? Maybe this is the cause of all my problems...
##DEBUG# screen > EVDO, at the bottom, says AUTHENTICATED and I have an IP address, stays solid like that in a 3g area.
Anyone like to help me out? What values do I may have incorrect for 1X to entirely not work at all but 3G works just fine??.. Being that 1X doesnt work, it seems to cause issues sometimes initializing a connection because it seems like 3G goes dormant/sleep after a while and maybe relies on 1X to be connected to keep a constant connection to the network. And.. this whole Data call failure thing is just obnoxious? Anyone truly find the result to this? Obviously has something to do with sprint, 4G is turned off, all the sprint .APK's are removed.
Being that the phone still has sprint options in Mobile Network Settings such as "Roaming" "Data roaming" etc.. could this be causing problems? How do I go about removing ALL of sprints network options on this phone???
thanks a whole lot... excited to see this phone working on the alltel network, would like to press on and get it working flawlessly.

Hey Steve I remember you from over at HoFo. Your Eris info helped me out getting some of my own issues worked out. I am still interested in what work you did to get your mms working in and out. I looked at the telephony.db once but didn't place a lot of effort in to it. So as it stands I get incoming but unable to send mms. So any insight from you would be greatly appreciated. But I will try and see if I can help you with what you have going on.
First I found that programming the Evo was more of a pain than when I did the HTC DInc on Alltel. In my area PRL 31005 is pushed to Alltel smart phones. It is the same PRL I used on the DInc with no issues. The Evo would insist that I was roaming with it. I switched to a non-divested PRL(30057) and haven't had an issue since. Google "answerman prl" for the download for Alltel PRLs. I have rocked with that PRL for over 3 months now. My roaming option is set for automatic in the mobile network settings and the only other thing I have checked there is data roaming, which I can disable with no problem.
Now if you go back to your HoFo thread I wrote that when I got the Evo I only had 1X data. It wasn't until after I went back over your thread and some other stuff that I managed to get 3G working. I used CDMA workshop(3.6.0 Licenced) And wrote the same things as you did. Only I have Mobile + Simple IP set and profile 1. Now I will say this. First I tried to set to profile 0 but when going into ##DATA#, the phone would always insist it wanted to use profile 1 even after having previously writing the data. So I created another profile in CDMA workshop, duplicated the data I had for 0 and made 1 active instead of 0. I had also previously never had issues with the "Data call failure" until the past month or two. After I rooted and moved from the stock rom I used CM6 for a good while even flashing nightlies and never had a problem. I only moved back to a Sense based rom when I was trying to troubleshoot an issue where my data would disconnect and would not re-establish for several minutes or until after a reboot. I was using juice defender at the time and incidently this was also around the time I updated my radio/PRI etc. So when I went to a random Sense rom this error message threw me off and I was sure something was wrong with the phone. But I have seen plenty of posts about it so idk. I run Myn's Warm 2.2 now. On rls1 I would get the DCF's frequently but not so much on rls 2, maybe once in a blue moon. I don't use juice defender anymore and I have also stopped using Set CPU as it conflicts with my current kernel anyway. *shrug* So no idea what truely makes the phone happy and not give me that error as much.
Hope this helps you.

Wow, that was a MESSAGE.
Thanks a whole lot for that.
For MMS:
When I use anycut to access the APN's on my Evo it shows it shows no apn's at all. I didn't add any and left it alone. Now...
I have attached the telephony.db file I edited with Root Explorer and SQL Lite editor. If you open the file in the editor, you'll see what I changed... It was simply an APN specifically for MMS use, changed it to alltel's values and.. BAM, perfect MMS.
Path:
/data/data/com.android./providers/telephony/databases/
Permissions are to be set to
USER: READ CHECKED - WRITE CHECKED
GROUP: READ CHECKED - WRITE CHECKED
No other's checked.
After replacing the telephony.db file, no reboot required, you should be set to send and receive MMS without any issues at all. If it fails, restart the phone or force quit messages and relaunch.
I will try that PRL you mentioned above, I am also on 31005... reports as the same PRL on my mother's alltel hero though, hmm.. doesn't make sense of why my phone still says I'm roaming.
I will also play with cloning profile 0 and profile 1 and switch back to sim+mobile IP mode...

Thread moved to Q&A.

Thanks I will give this a roll when I get home this evening. I hope that some of what I've given you will be helpful. I've been enjoying the phone and I will enjoy it even more I know once I get the MMS thing cleared up. Keep me up to date on what's going on.

Played with everything, did exactly as you said, still no 1X, if I go to ##data and tell it to use CDMA only (turn EVDO off), it just goes to no data at all while my Eris would just stick to 1x in that mode.
odd.
Can someone explain WHAT it is that allows a handset to receive the HA/AAA shared keys when a *228 activation is requested?
We all know that taking for example a Sprint phone and applying an alltel PRL to the radio ... that when activating it WILL NOT receive the HA/AAA keys for data...
Is it the AKEY ? Is it something else in the memory?
An old PPC6800 I have that was SPRINT.. it was a bugger getting data to work, just would NOT receive the HA/AAA keys or anything when *228ing the phone, as soon as I applied the Alltel Rom with the Alltel NV items, it activated without an issue and received all the correct NV items for data and all, worked perfect. How can we do this with the latest smartphone?...
Is it possible I can clone the NV items from my mother's HTC Alltel Hero and write them to my sprint Evo ?
What do you guys think?

Steve check your PM
I never had to do this myself so don't know how applicable it is.

I installed the file and assigned the permissions, now app just blows up when I try to send a pic msg. Any ideas?

STRANGE !
What messaging app are you using?
I am running stock latest OTA... So all the stock apps are installed, minus all the sprint stuff and a few other htc pre-loaded software I have taken out with root explorer.
Should be working perfectly. I have no idea what the deal is.
Did you go to Messages>menu>settings>connection settings and see if the values have changed?

I use Chomp SMS but it did the same with the native messaging app as well.

That's really strange. MMS still online and working flawlessly for me on alltel.
Phone still says I'm roaming though. Mother's HTC Alltel Hero in the same town is not roaming, both flashed with the same PRL and the NAM info looks identical in cdma workshop.
You sure your APN lists are empty? Mine is, no APN's at all in the APN viewer.

[q] flashed the desire sprint radio and prl install

I successfully flashed the CDMA Desire with a Sprint Radio off the Evo. It's baseband 2.15.00.09.01
I also installed PRL 60677 from sprint. I also tried the Cyanogen MOD.
It's currently running the alltel ROM so I can get access to the dialing codes in the PRL but even though I flashed the RADIO and the PRL it still shows the network as alltel and it won't let me get access in menu>settings>Wireless networks>mobile network
I can turn it on. But it either seems to take a long time to turn off, or go off by itself, not sure which. But once its on it is greyed out and won't let me get access to it.
I thought maybe it was the PRI, but I don't see how that could be. Is there some sort of Initial Program Loader from alltel doing this can someone tell me why it won't pick up on a sprint network that I have for cdma like connecting or sharing a connection etc... and won't get off U.S. Cellular network?
I might just try flashing to verizon and see what happens just to observe. It should be a lot easier than flashing to sprint.
edit: I did change all the dialing codes to sprint in the ## menu btw. I used the codes from another sprint Phone.
EDIT: It also won't turn off always when I hit Airplane mode and constantly says "Turning on...." and won't give access when to "Mobile Network" when you hold down the power button and that menu comes up.

I used the original Stock RUU to switch back. It changed the baseband and everything else back and also got rid of my clockwork recovery in the process
The only thing it didn't change is the PRL. I had to redownload that and manually rechange the codes in the ## secret dialing menu's.
As far as I understand I will need to change the esn or have this esn to sprint to be able to get it working on a sprint network. It is very difficult thing to do so I will have to postpone this. I'm thinking there might be some code or something in one of the abstraction layers or HAL layers that is preventing you from changing the esn somewhow... not really sure but that seems like the best place for me to look as it is the interface between the software and hardware. The hardware is there and able to do it, so it must be the most basic software or HAL that is preventing me from doing it I am guessing. BTW this is not illegal. I own my phone. If anything it's illegal for someone to sell me crap that doesn't work the way it should because of bogus programming that's been put on my phone to prevent me from using it! And nikola tesla invented the radio btw where is the money and credit he deserves for this?!

Hey man,
I am trying to do something like this for my wife. I'll let you know how it goes once I get the phone. In the meantime, maybe this might help you?
http://forum.xda-developers.com/showpost.php?p=4199684&postcount=5
I know it's not quite the same - taking VZW phone onto Sprint Network, but I thought it might help you out.
I'll post my experience later when I get the phone next week.
Thanks,
-Marcus

Eloquence said:
Hey man,
I am trying to do something like this for my wife. I'll let you know how it goes once I get the phone. In the meantime, maybe this might help you?
http://forum.xda-developers.com/showpost.php?p=4199684&postcount=5
I know it's not quite the same - taking VZW phone onto Sprint Network, but I thought it might help you out.
I'll post my experience later when I get the phone next week.
Thanks,
-Marcus
Click to expand...
Click to collapse
I don't think that's quite the same thing. I read through the post and a lot of it didn't make a whole lot of sense. Generally you have to have a compabible esn with the network you want to use. Every carrier has a database of all the esn's that are registered and available to use their service. If you try to connect to their service their software will recognize the esn as false and not grant service even if you install all the correct radio's/basebands, PRL files, Firmware, etc... it just won't work because you don't have an esn in their database so you have no authority to connect to their network. So you have to change the esn. But it's not such a simple thing to change an esn. I'm guessing its written in hexadecimal somewhere in the registry, but maybe not. There are certain command sets like the Haye's command set that only apply to CPU or other hardware like modem/Radio. There is an RIL which communicates between a driver, the modem/radio, and the OS. I'm guessing the esn is communicated and retrieved by the RIL layer that communicates via proxy & a driver or in one other PPP protocol that apparently only communicates with the network at certain times suspiciously. That's because the ESN is apparently located in the radio/modem and people have successfully changed their esn by changing their modem and installing a different one. A modem is essentially an ultra small electronic radio. In the same way that a radio picks up signals out of the air and converts to sound, a modem picks up signals also and can convert to sound as well as internet data, text messaging, etc...

If your radio doesn't have the proper command sets it can not pick up on certain signals such as for example sprint 1900 MHz for a sprint radio/baseband version vs a 900MHz signal for a 900 MHz Verizon. Each carriers software might be set up to block the other carriers signals in certain ways. For example each carrier has roaming agreements with the other carriers so that when you go out of your host carriers network say from Verizon into Sprint then you can "roam" and still get coverage. Sprint in this case provides the coverage and therefore they have an agreement to use each others network to provide better coverage. They may also pay each other small fees to use their network. Roaming, carrier type, cell number, mobile network operator, ip addresses, etc... can all be preprogrammed into CDMA handsets through ## secret dialing modes. This only works on CDMA handsets or in CDMA mode on your phone (i.e. not GSM). Usually on HTC devices you press ##775# to update a PRL file which is the Preferred Roaming List. That is usually easy enough, but this may not always update all your phones programming and you may have to do so manually through other ## dialing codes such as Primary HA secondary HA MCC (Mobile Country code) MNC (Mobile Network code) etc... Even if you do all that though it serves no purpose if the esn isn't registered to the network that you want to use. Generally only Cricket and MetroPCs in the USA will register a CDMA esn to use on their handsets. All the other carriers like Sprint, Att, Verizon, etc... generally won't do it, hence you can't get CDMA service from them if you have a CDMA capable handset even if you update all of your files as there is a program that is run on behalf of the carriers that manually checks your phones ESN/MEID/etc... to see if you have the "proper Credentials" or authorization to use their network. In this case the authorization is given on whether or not if your ESN is in their database and that it aslo can be in their database but blacklisted or grey listed in the case of you have an innactive account and need to pay them to get it "white Listed" or if you have a debt on your account or the phone is reported stolen it may be "black Listed". Usually you can flash to Cricket or MetropCs fairly easily though and they will even do it for you for a small fee.

PRL Issues

I have an EVO on Boost and I updated the PRL and since I get no service at all. I have flash like 30 different prls and same thing. I did a bunch of searching on the issue and cant come up with anything. What do I do?? Any help is appreciated. Thanks.

Ummm...try the EVO thread.
Thread moved
XDA Moderator

Well, which PRL are you on now?
Do you get an error?
If so, can you be more specific about it?
Are you sure roaming is disabled and set to home only?

I learned I had to re-apply all my settings but now I cant seem to get 3g working at all and everything is set up right just as before..??

HELP !!
ykman1 said:
I learned I had to re-apply all my settings but now I cant seem to get 3g working at all and everything is set up right just as before..??
Click to expand...
Click to collapse
I too am having issues
I use CDMA workshop.
Send SPC: AFTER FINDING IT AND WRITING TO 000000
USE PRL 50553
WHICH HAS WORKED WITH EVDO OR 1X PRL 10037
I changed the EVO to donor ESN of Incognito.
before i would change it
set prl.
turn on wifi and click on sprint zone
this would activate it.
as of nov 5th something in sprint/boostzone is blocking this activation method.
I CAN manually program and get talk and text working but no DATA or MMS.
I NEED HELP.
apparently theres a way with the 16/32 hex of te donor to set the aaa on profile 0
but i dont know the steps to do it this way.
the other way was much more convienent and Faster.,
ANYONE HELP PLEASE
text/call 9893267536

[Q] Sprint Galaxy S3

Ok, so I have a Sprint Galaxy S3 [SPH-L710] that I want to flash to Page Plus.
I've looked through Google, and have it working CDMA - 1xRTT
For the life of me, I can't find a way to get it working on 3G
Every conversation goes to: PM Me
[but the Convos are about a year old...]
Or use a Donor Phone
[But my MEID won't Stick...]
I have the SPC Code, and the 16 digit passcode for my SGS3
[and for the donor phone, but I hear you can get it working with no donor phone]
PRL: 53269-page-plus-sprint-phones
Any help would be greatly appreciated!

Pretty sure you should edit those pictures so they dont show your MDN (phone number), MIN, and MEID.
The few people who know how to get 3g without a donor don't want to share, so you will need a donor to get the keys or find somebody willing to get them for you.

Stuck
Dermen said:
Pretty sure you should edit those pictures so they dont show your MDN (phone number), MIN, and MEID.
The few people who know how to get 3g without a donor don't want to share, so you will need a donor to get the keys or find somebody willing to get them for you.
Click to expand...
Click to collapse
That's what I was afraid of, good ol Capitalism...
I do have a Donor Phone, but the MEID/ESN won't Stick...

Got it!
Ok, so you have a Sprint Samsung Galaxy S3, [SPH-L710] and you want to Flash it to Page Plus?
[I'm assuming this will work for ANY carrier, but we all know what assuming does...]
Take it to dealer and have the MEID activated.
Flash the PRL of carrier you want to switch to, restart phone.
You'll also need to change the SPC on the Phone to 000000
Here's the trick, you need another phone with the dial pad open and ready.
hold the other phones speaker to the mic of the S3
Dial *228 on the S3 you want activated.
When it asks you to press 1, press one on the other phone,
The S3 will hear the dial, and proceed to program it for you.
[Back in the day if you recorded the tones that were made from a payphone after paying, you could play it back,, it would hear the dial, and think you paid, when you didn't]
Now Flash a correct PRL [I have provided a copy I used for Page Plus]
No Roaming Signal
CDMA - EvDo Rev.A
Blam, it works.