Develop Bugs

Remove HardSPL

How do I remove HardSPL so that I can load my factory rom for a warranty return?
Can I just the load the vendors ROM or will this brick my phone?
My diamond is a UK vodafone version and I have a copy of their official ROM, I read this thread
http://forum.xda-developers.com/showthread.php?t=342744
but it says I need the IPL/SPL based on your device and carrier where would I get these?

you need to flash the ROM and Radio back first, then find a stock SPL and flash that.
MAKE SURE THE SPL IS THE LAST THING!!!

i even found the stock SPLs for u
http://forum.xda-developers.com/showthread.php?t=400411

mugglesquop said:
i even found the stock SPLs for u
http://forum.xda-developers.com/showthread.php?t=400411
Click to expand...
Click to collapse
I am not the one who asked the question but I thank you also. I don't need to reflash the rom for return but I will bookmark this just in case .

Thanks but I'm a little confused now, how do I flash the ROM and Radio back first and what is the SPL then. I followed the link http://forum.xda-developers.com/showthread.php?t=400411 but I think these are the roms aren't they?

Yes, those are the ROMs. They do also include the radio.
Just use either the original RUU Updater to upload it to the phone or the patched one from OliNex.
After that you have to upload the original SPL.
See http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39
for detailed instructions.
Cya,
Viper BJK

mugglesquop. Thank you for the original SPLs but I dont see the UK orange stock SPL listed...Can I use any 1.37 SPLs????
I used the search function on this forum and could not find the stock uk orange SPL. Thanks.

Afaik there are no stock orange spl. Standard spl (same version) should work.
To be sure, get a orange rom and extract the spl from there.

viperbjk. Thank you for the info. I extracted an orange ROM and found a file named "RUU_signed.nbh". I believe this is the bootloader file that I will need to load after installing the original orange ROM.
Hopefully this will work and can send my Diamond back to orange.Thanks

The RUU_signed.nbh is normally the complete rom package. You have to extract it, to see if SPL is in it.
Cya,
Viper BJK

I can confirm there is no "orange" SPL

Urgent! My diamond has hardware problem and need to fallback to stock ROM and SPL.

Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810

Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help

Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.

If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included

Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.

You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU

I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!

Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.

band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?

Here you go....I did a search

Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!

Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4

band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...

kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.

f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that

f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.

Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??

R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?

f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...

f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??

Easy SPL Question (just need confirmation, cuz I don't want to f*** my device)

I want to flash a new ROM to my device and now I need to HardSPL it, now my question is, is there any way of backing up the old one, so that I might put it back on the device for warranty reasons or if the ROM does not work and I want to go back to the stock one?
Thank you in advance.
gdata

Okay, I was able to unzip the exe containing the ROM. I read somewhere that I can extract the SPL from these files (see attachment), but I think the tutorial I found was not for the Diamond, so maybe someone can point me to the correct tutorial, how to put the SPL from that ROM on my device (and yes, I want to get the ORIGINAL HTC ROM and SPL).
I assume I can use the same method to put the original ROM and SPL on the device again if necessary?
edit: Can somebody tell me whether I can use this tutorial: http://forum.xda-developers.com/showthread.php?t=335568 to put the htc spl on my device? I just wondered because it's for the Kaiser and for the restoring the original one, but in theory I should be able to flash the HTC SPL on my O2 device then, shouldn't I? So in the end my O2 SPL has been changed to a HTC SPL and I can install the HTC ROM?

A way to undo HardSPL ??

My buddy has a Tilt 2, and has decided to get another phone.
He wants to get it back to stock, and put it on ebay.
I know he can flash back to the stock ROM floating around.
Is there any way to undo the HardSPL, so it will be really stock ?
Thanks.

69Pwned said:
My buddy has a Tilt 2, and has decided to get another phone.
He wants to get it back to stock, and put it on ebay.
I know he can flash back to the stock ROM floating around.
Is there any way to undo the HardSPL, so it will be really stock ?
Thanks.
Click to expand...
Click to collapse
Detials found below were retreived from <<HERE>>...at the end of POST #2
how to reflash Stock/Shipped SPL - STEP BY STEP - FOR WARRANTY REASONS ONLY!
0. please make sure you already flashed stock ROM and radio, because stock SPL flash is *always* the last step before sending the device in.
1. download the Relocker attachment, extract the zip and run the EXE on your PC
2. if you wish to replace RUU_Signed.NBH that got extracted, feel free to do so, but not necessary (this Hard-SPL will only allow overwrite with a SPL signed by our custom cert). the included one is the 0.79.0000 stock SPL. you also have the option for 0.84.0000 and 0.87.0000, see the attachments.
3. flash
4. verify if it flashed by checking version in tricolour screen, it should say 0.79.0000 (or 0.84.0000 or 0.87.0000), not 0.85.OliNex.

Awsome thanks, i'll give him the info ........

69Pwned said:
Awsome thanks, i'll give him the info ........
Click to expand...
Click to collapse
No Problem....

[Q] Soft SPL

I dont now what rom to use on my TP2.
IMEI:xxxxxxxxxxxxxxx
S/N: xxxxxxxxxxxx
P/N:99HHL011-00 F

Extra info
St3v3-) said:
I dont now what rom to use on my TP2.
IMEI:xxxxxxxxxxxxxxx
S/N: xxxxxxxxxxxx
P/N:99HHL011-00 F
Click to expand...
Click to collapse
After the soft Spl. Witch rom do i need too choose out of the 5? I have the European TP2. I used the hard SPL but I need to send the phone back so the hard SPL has to go. So can any one help me.

St3v3-) said:
After the soft Spl. Witch rom do i need too choose out of the 5? I have the European TP2. I used the hard SPL but I need to send the phone back so the hard SPL has to go. So can any one help me.
Click to expand...
Click to collapse
How to reflash Stock/Shipped SPL - STEP BY STEP - FOR WARRANTY REASONS ONLY!
1. Flash the Stock ROM. If the stock radio isn't included, flash that as well. This must be completed first.
2. Download the Relocker attachment, extract the zip and run the EXE on your PC.
3. If you wish to replace RUU_Signed.NBH that got extracted, feel free to do so, but not necessary. This Hard-SPL will only allow overwrite with a SPL signed by our custom cert. The included one is the 0.79.0000 stock SPL. You also have the option for 0.84.0000 and 0.87.0000.
4. Flash the SPL.
5. Verify if it flashed by checking version in tricolour screen, it should say 0.79.0000 (or 0.84.0000 or 0.87.0000), *not 0.85.OliNex*.
Rhodium SPL Relocker
Stock SPL Restore 084
Stock SPL Restore 087

St3v3-) said:
I dont now what rom to use on my TP2.
IMEI:xxxxxxxxxxxxxxx
S/N: xxxxxxxxxxxx
P/N:99HHL011-00 F
Click to expand...
Click to collapse
In the future, please do not post sensitive information in an open forum. This is like posting your Social Security Number on a banking forum.