p3300 no power; no charging lights etc. sometimes boots just fine - P3300, MDA Compact III General

i have a p3300; no power lights when charger is connected; doesn't power on as well. battery is fully charged, battery and charger are both fine. but sometimes the p3300 powers on just fine; if i connect the ac charger then it also charges the battery. but it hangs in windows mobile 5 after some time (trackball and buttons and system does not respond anymore); after a soft reset no power/power lights or boot at all. then after some time and fiddling it might power on again and the cycle starts again.
i know it is a common problem; but is there a solution?
the backup battery (yes, there is one in it. the same as in the qtek 8310) gives me 0.20 volt. not sure how much it should be. but the backup battery in my qtek 8310 gives also 0.20 volt. not sure whether both are drained or that the voltage is normal.
will a drained backupbattery prevent it from booting up fine? or... hope to get it up running reliable again; great navigation phone with tomtom.
edited:
without the battery installed i get a red light flashing quickly if i put the 5volt charger on it; same if i connect an usb cable (connected to my computer);
if i have the battery installed; i do not get a red light flashing.
with the battery plugged in and the charger plugged in; i don't see any charging lights. but it does charges my battery; i started with 3.7 volt, and it is going up (now at 3.9 volt).
in both instances i cannot get it to power on/into bootloader mode.

i've got exactly the same issue
I was given this phone by my brother as its broken, i tend to get alot of his broken stuff anyway i stripped the phone down and found that the little battery inside had leaked so i did a little bit of hack wiring and bodged a 3.3 volt battery used in a PC to power the cmos chip well it seems to have sorted the problem apart from the fact there are two wires hanging out of the phone but i've also noticed this battery voltage has dropped to 2.6 v now and still dropping over the days i'm guessing i'm going to have to make it replaceable.
oh just for the record
my brother tried a replacement main battery on it originally and tried flashing it with a clean rom to try and fix it but it carried on hence passing it on to me

...
...to both of you...
buy a new battery..
leave it OFF while charging!!!
when the green led comes on (orange while charging... red flashing indicates battery is dead)
done.. turn it on..
batterys are cheep on ebay..
(if this dont work, pm me.. it could be something totaly differant but buying a new battery is the usual soloution for this common problem)

Related

what does mean a very fast flashing red led

hey guys i just bought a new battery for my jasjar, the phone isnt booting even if the charger is plugged in, it only boot for like 6 seconds before it turn off again, even if i charged the new battery for 10 hours, even there is no orange led tell that the battery is charging... i plugged the phone into the USB cable with the pc and a fast flashing red light comes from the led (like 3 flashes per second) so what is the problem? is the new battery damaged or what? please help
djgaby said:
hey guys i just bought a new battery for my jasjar, the phone isnt booting even if the charger is plugged in, it only boot for like 6 seconds before it turn off again, even if i charged the new battery for 10 hours, even there is no orange led tell that the battery is charging... i plugged the phone into the USB cable with the pc and a fast flashing red light comes from the led (like 3 flashes per second) so what is the problem? is the new battery damaged or what? please help
Click to expand...
Click to collapse
In all probability you have received a deffective battery. Please obtain a replacement or refund.
djgaby said:
hey guys i just bought a new battery for my jasjar, the phone isnt booting even if the charger is plugged in, it only boot for like 6 seconds before it turn off again, even if i charged the new battery for 10 hours, even there is no orange led tell that the battery is charging... i plugged the phone into the USB cable with the pc and a fast flashing red light comes from the led (like 3 flashes per second) so what is the problem? is the new battery damaged or what? please help
Click to expand...
Click to collapse
red light means extremely low batt.....guess your battery is faulty
i got the same thing.
and no it's not the battery.
it's the charging circuit on the main hardware isn't working.
open your phone and check the five small wires that they connect the mini usb to the main mother board, one of them must be cut.
Ninlour said:
i got the same thing.
and no it's not the battery.
it's the charging circuit on the main hardware isn't working.
open your phone and check the five small wires that they connect the mini usb to the main mother board, one of them must be cut.
Click to expand...
Click to collapse
so, is there a solution to this? or there really is nothing more for the device but the trash bin or for spare parts?
Have you tried this?
http://wiki.xda-developers.com/index.php?pagename=UniversalBatteryIssue
If you already replaced the battery and nothing, and you want to get rid of dear Uni place it for sell in parts on marketplace, a lot of people will go for it!
djgaby said:
hey guys i just bought a new battery for my jasjar, the phone isnt booting even if the charger is plugged in, it only boot for like 6 seconds before it turn off again, even if i charged the new battery for 10 hours, even there is no orange led tell that the battery is charging... i plugged the phone into the USB cable with the pc and a fast flashing red light comes from the led (like 3 flashes per second) so what is the problem? is the new battery damaged or what? please help
Click to expand...
Click to collapse
I had exactly the same thing with my old battery,after my try to discharge it with a lil electro-motor. then i found a post of a guy with the same thing,who fixed it-by "zapping" the UNI battery with a 9V battery,connecting + to + and - to -,for a few second. I tried it without thinking twice. It worked for me. Dunno how and why,but it did. I use the battery again,normal. But beware,it is dangerous to play with this type of battery,it can explode. Do a search on this subject and you will see
I agree with keeping_sg
how long have you left your uni on the charger?
just plug it in and leave it on the charger all night and see what happens.
I bought yesterday a 4800mAh battery from Hong Kong... 10 euros included shipping + FREE black back cover
Good battery life but still prefer to carry 2 original sized batts rather than get that big one, making even bigger our Uni
Respectfully,
Yes, that absolutely means your battery is dead. Try charging for a few more hours and then turn on your PocketPC. If the error persists, try changing the battery.
Regards,
Carty..
Yes, that absolutely means your battery is dead. Try charging for a few more hours and then turn on your PocketPC. If the error persists, try changing the battery.
Regards,
Carty..

BA turning off if removed from cradle and not turning on again

Hello guys,
I have a problem, i haven't used my VPAIII for 6 months, and some days ago i wanted to turn it on, and it didn't react, so i decided that battery is low, i connected my device to cradle, and wait for some hours. So the problem is then device in cradle it's ok i can switch it on and it works perfectly, but if i remove it from cradle it turns off imediately and i can't turn on it again without connecting to cradle chargement, also it doesnt react to usb connection as chargment. Battery is totaly new it was bought from ebay (expanded 3400 mAH). Interesting thing that if i connect to cradle, device turns on automaticall and 1 time blinks led in red and goes booting system with no led light, after i see Windows screen it starting show the same right led in orange always, i see charging battery meter in windows but battery didnt go more then 50%, and everytime i boot on i receive Backup battery Very Low notification no matter how much i was charging my battery.
So i'm afraid maybe it's internal backup battery failure, or my main battery didn't get chargement then it says that charging. Maybe someone of You guys have any usefull advices, what can be the problem? Also if it possible maybe somebody can give me alink or image to see there this backup battery soldered on scheme.
Thanks ppl!!!
Raz
razorrazor said:
I have a problem, i haven't used my VPAIII for 6 months, and some days ago i wanted to turn it on, and it didn't react, so i decided that battery is low, i connected my device to cradle, and wait for some hours. So the problem is then device in cradle it's ok i can switch it on and it works perfectly, but if i remove it from cradle it turns off imediately and i can't turn on it again without connecting to cradle chargement, also it doesnt react to usb connection as chargment. Battery is totaly new it was bought from ebay (expanded 3400 mAH). Interesting thing that if i connect to cradle, device turns on automaticall and 1 time blinks led in red and goes booting system with no led light, after i see Windows screen it starting show the same right led in orange always, i see charging battery meter in windows but battery didnt go more then 50%, and everytime i boot on i receive Backup battery Very Low notification no matter how much i was charging my battery.
Click to expand...
Click to collapse
It sounds like the main battery is bad.
Is the battery you picked up new, or new as of 6 months ago? If it's new-new, it is still possible that it is bad.
Also, the charging circuit may have died. Most electronics will work and work, and when they do die, it's usually when power is applied to them (turned on, charged, etc).
The fact that it does charge up to 50% makes me think the main battery is bad. Do you still have the original battery? Try it and see what that does.
razorrazor said:
So i'm afraid maybe it's internal backup battery failure, or my main battery didn't get chargement then it says that charging. Maybe someone of You guys have any usefull advices, what can be the problem? Also if it possible maybe somebody can give me alink or image to see there this backup battery soldered on scheme.
Click to expand...
Click to collapse
The internal battery is used only when the main battery is discharged or missing.
As for a link, hit the wiki.
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel
Under the "Hacks & Tweaks" section, go into "Technical Stuff".
Thanks for reply, new battery i bought maybe 4-6 months ago i used it maybe 1 week, after that i turned off my device and left it for 4-6 months, so nothing should be happened to battery. I'll check device with old one, but it seems that device didn't work with original old one battery too.
Any other solutions, advices?
Thank You very much guys for help!!!!
RAZ

problem with new hicap battery

hi all
Just put in my hicap battery-2600mAh yesterday.
all attempts to charge it have failed however.
----------
the problem-
with new batt inserted, i plug in the charge cable
no charge light (orange), no low batt light (red)
once WM is booted, it shows that the status is Charging
but stays stuck at 0% even after an overnight charge.
Taking the charge cable out, the phone is ON for about 20 seconds,
then goes into Standby mode all by itself but does not actually switch OFF or run out of batt after n hour of mucking about on it
-----------
it does not look like a dead battery as it is actually able to hold some amount of charge
a faulty battery perhaps?
or is there a special way to charge brand new batteries?
or a workaround to the problem?
thanks.
suggestions anyone?
resco2007 said the following in another post:
I wanted to let you know that I have the same problem with mine too : xda2 s do not like mosot chargers that is what it is but I have found a way around it, this is what you do- switch off the phone and then take off your batt for a split second and then put it back on , now the phone is off , now you can charge it,
It works for me and a few others
=======
but unfortunately ive not been able to get my phone to charge that way.
there dont seem to be a way for me to switch the phone off completely in that, when the little notch is push back in, it immediately boots...

[POSSIBLE FIX] Flashing red light - dead phone/inferior USB cables

Today I had my One X happily connected to my pc, just transferring some files over by USB. Then when I wanted to disconnect it, it showed a lot of 'not getting enough current to charge and operate at the same time' messages. Dismissed them all, though it was time to put it on the wall charger, seen it's critical battery status.
Once I disconnected the phone, it immediately powered off and would not come back to life again. It was, however, greeting me with a flashing red light while on the wall charger. No matter what I tried (bootloader, long hold power button, charge it for some time), it remained completely dead.
Now I did get some new micro usb cables from eBay. Very cheap ones. Now I think these are the culprit. Apparently, while in file transfer mode, these cables were unable to provide sufficient current, causing the phone to drain the battery completely. Once I wanted to charge it, it couldn't boot to charger mode due to the battery being completely empty.
Hooking up with the original HTC cable again, it still showed the red flashing light. Exact same behavior. Until I (for the heck of it) tried to bash the power button quickly. It suddenly came back to life again and started charging again through PC.
If you find yourself in the same situation with bad USB leads (something to do with resistance of the cable?) or a red blinking light, try tapping the power button quickly instead of trying to boot into recovery mode. It might save you a postal return and a week or 3. Or your ass, if you rooted it before it stopped charging.
When I had my sensation I had this every now and then. I had to remove the battery to get it to work.. Nice to know that there appears to be something I can do to sort this out if I get this now
BLAST3RR said:
Today I had my One X happily connected to my pc, just transferring some files over by USB. Then when I wanted to disconnect it, it showed a lot of 'not getting enough current to charge and operate at the same time' messages. Dismissed them all, though it was time to put it on the wall charger, seen it's critical battery status.
Once I disconnected the phone, it immediately powered off and would not come back to life again. It was, however, greeting me with a flashing red light while on the wall charger. No matter what I tried (bootloader, long hold power button, charge it for some time), it remained completely dead.
Now I did get some new micro usb cables from eBay. Very cheap ones. Now I think these are the culprit. Apparently, while in file transfer mode, these cables were unable to provide sufficient current, causing the phone to drain the battery completely. Once I wanted to charge it, it couldn't boot to charger mode due to the battery being completely empty.
Hooking up with the original HTC cable again, it still showed the red flashing light. Exact same behavior. Until I (for the heck of it) tried to bash the power button quickly. It suddenly came back to life again and started charging again through PC.
If you find yourself in the same situation with bad USB leads (something to do with resistance of the cable?) or a red blinking light, try tapping the power button quickly instead of trying to boot into recovery mode. It might save you a postal return and a week or 3. Or your ass, if you rooted it before it stopped charging.
Click to expand...
Click to collapse
It was mentioned that the flashing red (or orange?) meant that the temp was too high.
Just let it cool down, and it will come back.
It definitely wasn't hot. Also, it wasn't flashing orange. Just slowly red.
BLAST3RR said:
It definitely wasn't hot. Also, it wasn't flashing orange. Just slowly red.
Click to expand...
Click to collapse
Same situation when I had my sensation
Sent from my HTC One X using xda premium
BLAST3RR said:
It definitely wasn't hot. Also, it wasn't flashing orange. Just slowly red.
Click to expand...
Click to collapse
Your quite right. Overheating on charge flashes red then green. Never seen a flashing red so can't comment
Sent from my HTC One X using XDA
bagofcrap24 said:
Your quite right. Overheating on charge flashes red then green. Never seen a flashing red so can't comment
Sent from my HTC One X using XDA
Click to expand...
Click to collapse
Ah, I have had that once while playing games and having my HOX on charge
Sent from my HTC One X using xda premium
Someone has also posted
flashing orange - low battery
flashing red - very low battery
It could well be the battery level is considered too low to operate. So to protect the circuit and the battery, the device is not allowed to turn on until it is sufficiently charged.
This is currently (no pun intended) happening to my one x, left it plugged into my pc via the htc usb and got flashing red light after a couple of minutes, after a couple of minutes more it stopped flashing and became a solid red light (a sign it is charging from v low battery from m experience) pressed the power button and voilĂ  its come back on. I can't believe htc would let the device get to such a critical state of battery before powering down, can anyone enlighten me as to why it would do this?
(thinking about it i was showcasing the handset to my apple touting buddy and had 3 pretty heavy apps running, it was a couple of hours after i noticed it had killed itself so i'm guessing they were still draining away the power from the background??)
I'm having the same problem. My phone was off when i got home and it wouldn't turn on (I assume the battery was dead). When I put it on the wall charger the red the red light didn't turn on and my phone wouldn't boot. I tried several chargers and cables and also tried to connect it to my pc. After leaving the phone for a few hours (unplugged) i tried to connect it to my pc again and i got the blinking red light. A few minutes later I decided to plug it into the wall and the red light turned on and now it is working normally.
anyone got an idea why it didn't charge at first?
agree chaging cable fixed my flashing red light problem
Poor quality charging/data cable
A poor quality charging/data cable will also impact the ability to charge the HOX in your car. I have two cars, in one I was using an old Blackberry cable and Griffin charge adapter (1amp output) to charge the phone whilst using Car Dock and navigation software. After trial and error I got the screen brightness correct and the phone charged satisfactorily. I say satisfactorily because I still think any electronic device which is connected to an external power supply of sufficient electrical current should operate and charge at full spec. In my other car (1996 Land Rover Discovery) I was using a cheap ebay charging/data cable. Using the same apps and screen brightness the HOX would lose all charge over about a two hour period. With the same Blackberry cable used in my other car, no problem. Hence the cheap ebay cables are now in the bin.
BLAST3RR said:
Today I had my One X happily connected to my pc, just transferring some files over by USB. Then when I wanted to disconnect it, it showed a lot of 'not getting enough current to charge and operate at the same time' messages. Dismissed them all, though it was time to put it on the wall charger, seen it's critical battery status.
Once I disconnected the phone, it immediately powered off and would not come back to life again. It was, however, greeting me with a flashing red light while on the wall charger. No matter what I tried (bootloader, long hold power button, charge it for some time), it remained completely dead.
Now I did get some new micro usb cables from eBay. Very cheap ones. Now I think these are the culprit. Apparently, while in file transfer mode, these cables were unable to provide sufficient current, causing the phone to drain the battery completely. Once I wanted to charge it, it couldn't boot to charger mode due to the battery being completely empty.
Hooking up with the original HTC cable again, it still showed the red flashing light. Exact same behavior. Until I (for the heck of it) tried to bash the power button quickly. It suddenly came back to life again and started charging again through PC.
If you find yourself in the same situation with bad USB leads (something to do with resistance of the cable?) or a red blinking light, try tapping the power button quickly instead of trying to boot into recovery mode. It might save you a postal return and a week or 3. Or your ass, if you rooted it before it stopped charging.
Click to expand...
Click to collapse
Many thanks to you good sir!!!
NorthS said:
Hence the cheap ebay cables are now in the bin.
Click to expand...
Click to collapse
The HTC-cable isn't that good too. I use a Nokia-charger to charge my HOX. Charging is much quicker. Maybe the HTC--charger (and cable) was crappy but i never touch them, i use the Nokia charger and dito USB cable.
Thank you!
blast3rr said:
today i had my one x happily connected to my pc, just transferring some files over by usb. Then when i wanted to disconnect it, it showed a lot of 'not getting enough current to charge and operate at the same time' messages. Dismissed them all, though it was time to put it on the wall charger, seen it's critical battery status.
Once i disconnected the phone, it immediately powered off and would not come back to life again. It was, however, greeting me with a flashing red light while on the wall charger. No matter what i tried (bootloader, long hold power button, charge it for some time), it remained completely dead.
Now i did get some new micro usb cables from ebay. Very cheap ones. Now i think these are the culprit. Apparently, while in file transfer mode, these cables were unable to provide sufficient current, causing the phone to drain the battery completely. Once i wanted to charge it, it couldn't boot to charger mode due to the battery being completely empty.
Hooking up with the original htc cable again, it still showed the red flashing light. Exact same behavior. Until i (for the heck of it) tried to bash the power button quickly. It suddenly came back to life again and started charging again through pc.
If you find yourself in the same situation with bad usb leads (something to do with resistance of the cable?) or a red blinking light, try tapping the power button quickly instead of trying to boot into recovery mode. It might save you a postal return and a week or 3. or your ass, if you rooted it before it stopped charging.
Click to expand...
Click to collapse
thank you! Thank you! That cheap usb was totally the problem!
Small update.
This problem just happened to me. 1 cord gave me flashing red while plugged into the wall and pc. I switched to my other cable and its charging and functioning normally. Cord was the problem.
I had a similar issue with my one x.
It discharged completely, then when I went to charge it I just got the red blinking light for ages. I left it charging overnight thinking the battery was so low it needed a while to charge enough to be able to switch on.
But in the morning it was still flashing and the phone was very hot, so I thought the battery was blown.
So I came on here and saw a suggestion about holding the power button and the volume down button. It went to the boot menu and said there was not enough power for a factory reset or something, so I selected recovery. I then got a warning icon and the phone switched off again, but this time with a solid red light. A
After a while I was able to turn it back on again.
Hope this helps.
Wellllll
I have the HTC One VX. I know this isn't in the same topic, but since I found the thing that helped/worked here, I thought I should share my experience. So I bought my new phone on Sunday, so it is roughly 5 days old...not even a full week. I charged the phone before I went to bed to roughly 80%. I made sure all apps and what not were turned off and pressed the lock button. I woke up in the morning and checked my phone to see what time it was. Had 78% battery left. I left it on my dresser for roughly 2 hours and when I got back from class, I grabbed my phone to check if I had any messages.
The phone didn't turn on and I didn't even get the flashing orange/red light. So I tried charging it and nothing. I changed wires and nothing. I frantically searched the internet and stumbled upon this forum/thread. I tapped the power button at least 15 times consecutively and the phone barely flashed orange. I tried to plug it in again and rapidly pressed the power button 10 more times and the screen finally turned on. It started charging and I checked the battery life. Somehow, in 2 hours my phone drained itself of 78% battery life when it was on the lock screen (its also set to lock after 15 seconds of inactivity) to the point where it couldn't even turn on.
The phone/battery was not even warm/hot or w/e. It had not touched any water. No idea what caused the immense power drain, but glad it is working. Thank you so much for this help
woops, wrong thread
It happens to me allso in this morning, in my opinion is like this: The phone is turning off when basicly you have a little bit batt (lets say something around 5% max) and its turning off to protect data and is showing to you batt empty. Then it cames a user with a charger connected to a power supply (house charger,car charger or directly to pc's usb). You must use a good usb to micro-usb charger (the original ones are't good usb cables) try to use a Nokia usb to micro-usb cable, This was the first problem most usualy. The second one is to pay a HUGE attention to UC, don't uc'it so much because then the charger board will not charge your batt so well. Keep yours HOX safe and anjoy it. Have a nice day boys and girls.

[Q] HTC infamous Battery charging bug with M8

Just got my M8 first time I turn it on it had half charged battery. I drained it to a point when I turned it on two times and than it went dead. I mean I could not turn it on. When I connected the charger no light came on and no response from phone. I leave it till toomorow and see if it will turn on.
I fear HTC is using the same chip for controling battery charge in M8 which if flawed by infamous HTC charging bug. If this is the case it is really start annoyng me and htc m8 will be my last HTC phone. I had so far Wildfire, Sensation ,Desire and all off them had a charging bug. Wildfire and Desire would not show the battery full even though battery voltage was at full charge. My luck? Or HTC has some poor quality components? My S2 still charges battery fine till today.
Ok. Anyone can check their M8 if you have charge bug if you battery is almost drained off power if it will turn on or stay dead?
If my won't wake up tommorow after all night at charging I'm gona exchange it on warranty and see another sample has the same charge bug.
Why HTC is not doing something with this CHARGE BUG on the newest devices? Puzzeles me.
I brought mine to 1%, cycled the power, then used it again till it died. Plugged it in, charging icon came on right away, charging light as well. Hope this answers your question, I didn't really read the whole post.
=)
Sent from my HTC One_M8 using xda
Visspui said:
I brought mine to 1%, cycled the power, then used it again till it died. Plugged it in, charging icon came on right away, charging light as well. Hope this answers your question, I didn't really read the whole post.
=)
Sent from my HTC One_M8 using xda
Click to expand...
Click to collapse
My M8 has just died because it wont charge, happened just yesterday. I left it plugged in over night and still nothing. Its a holiday here at the moment so have to wait until Wednesday for HTC to open.
Possibly The same Problem, Possibly Not?
andy905 said:
My M8 has just died because it wont charge, happened just yesterday. I left it plugged in over night and still nothing. Its a holiday here at the moment so have to wait until Wednesday for HTC to open.
Click to expand...
Click to collapse
Hi.
I've been having loads of problems having unlocked, rooted, S-Off, SuperCID & installing the ARHD ROM on my M8 (International) but it was, in a fashion, working. I too am on holiday & whilst I now know why I was having the issues & have the solution to them, I didn't have time before I left to resolve them. So, I brought it away with me to use for basic currency conversion & translation tasks & it was, as I say, functional. Last night, I decided to play a game on it & it was being laggy but I put this down to the issues I've been having, so didn't worry. It kept being laggy, so I tried restarting it to see if that would help but once it had powered down, it took ages to reboot, so I tried using the power button to switch it on. Again, it took ages & I briefly fell asleep but when I woke up, it had booted back into ARHD, so I figured all was okay.
However, when I awoke this morning, the device would not switch on. I plugged it in to see if something had caused the battery to drain during the night but nothing happens; the charging light doesn't come on & it doesn't power up, no matter how long I leave it! It is, to all intents & purposes, behaving as though it is dead (bricked?) but I don't know why it should suddenly do this, which is why I was looking for answers & came across this thread.
If anyone has any bright ideas, I'd be more than grateful to hear them
Mine needed a replacement charging board and chip unfortunately but HTC Vietnam was pretty fast, only took 3 days so wasn't too painful.
I like how "Happened to three people" == "infamous."
Yes, this sounds like a very isolated bug/defect. Since it is not reported by very many, the best course of action is RMA. ?
My T-mobile HTC ONE M8 has done this as well, however I was after serveral hours of trying everything I could think of, connecting it to the computer and various chargers and trying to hold volume up and power and replugging it to charger, it finally started charging. This has happened 2 times in the last 2 weeks.
Now that it's charging I wonder if HTC will take it and replace the charging board or battery. I also worry that I have it rooted and s=off that they won't honor the warranty.
There is something similar to this going on with mine - Was charging (maybe quite slowly), battery very low, phone reset. Booted into charging screen, amber light flashing. After a while (and trying to boot a few times), no light, nothing. Charge current is 0.00A
Edit: I remember something like this with the old Desire - there was a trick to reset the charging circuit, which was maybe locked up and not getting a good po_reset, so never enabling any charge. Something along the lines of unplug, hold some buttons for some time, plug, profit... Does anyone remember this in detail?
I had the issue in this topic, and got it solved.
Here are forums where I have found similar case and solution.
https://www.noppanit.com/htc-one-wont-turn-on-after-battery-completely-drained/9h53
http://www.pocketables.com/2015/06/htc-one-m9-unresponsive-no-charge-light-wont-power-on.html
http://forum.xda-developers.com/showthread.php?t=2481211
I have a particular case. My phone is a HTC One M8, but I have protected it with a special case with a battery extension, home made. I have assembled myself the batteries, chargers and boosters. My booster has a small issue and does not enter safe mode when battery is low. It warns about low batt with a LED, but still tries to deliver 5V. The booster is connected to the phone via a flat cable, stolen from a wireless charger; those chargers have the smallest USB plus I could find ever, and, I found this plug only in these decvices.
When the main battery of the phone is empty, I switch the booster on, and recharge the phone with the backpack. I have to look at the LED; when it's red, I have to switch it off. Everynight, everything get charged on the same single plug. One plug to charge both batts.
The advantages of my solution are:
- phone can last 18h with heavy work (wifi, bluetooth, GPS, and screen on, continuously)
- heavy case to protect my phone, plus tampered glass
- one plug to charge everything
- the micro-micro USB plug is ALWAYS in the phone. This means, the female plug of phone can not get dirty, or filled with dust. I never unplug it, so it does not age. I never plug a classic USB cable directly in the phone, so, no chance to break it. I have broken 3 or 4 times the back charger plug; if I am in hurry, I can exceptionally charge the phone directly; next day home, I can fix it.
This night, I was using my phone, and switched the backpack on. I could not plug my wall charger, because it's home made, has an issue, and makes the virtual keyboard erratic. I fell asleep with the phone in my hand, and the backpack went red ... for 4 hours. During 4 hours, it was trying to deliver 5V, and failed at so. Since my battery was delivering an unstable +5V, the phone was trying to charge, was staying on, but could not properly charge. In the end, all batteries got flat.
This morning, when I woke up, I plugged the stuff; only the back-batt started charging. Phone itself refused to charge; screen was black, and charging LED stayed off. So, I fell in what we call the "phone refuses to charge".
But, because of my set-up, I can *NOT* be in the dirty or broken plug case. Just impossible. And because of context, I just knew I had a flatt battery. This is technically called "deep discharged". And it contributes to aging of batt. Like overcharging, this heavily affects the total capacity.
I knew I could fix the issue by opening the phone, and putting a LiPo charger directly on the batt lines. I have loads of standalone chargers. I had a standalone wall charger for my previous HTC Sensation. But with the M8, we can not just open the case, and take the batt out. It's much more complicated. So, I have been Googling for more than half an hour. 95% results were about "remove dust of plug" and "bring it to the shop to change your plug". Some people also mention "a bug in the charger chipset".
I have plugged the phone on a classic USB charger, but via an USB meter monitor:
dx.com/p/382581 (dispite description, the device can accept up to 13V on input - this detail is critical when you use real QC2 chargers able to deliver 9 and 12V, like this one:
http://www.amazon.fr/Chargeur-secte...&qid=1451509059&sr=8-4&keywords=aukey+charger
http://www.amazon.fr/batterie-exter...&qid=1451509059&sr=8-5&keywords=aukey+charger
)
The USB meter was indicating 5V 0.03 A (or 9V 0.01 A, depending on source). So, the phone was using a bit of energy, but clearly not charging. I have left it 4h. Just in case, can not harm.
Then, I pressed together power, and volume up. The phone started to boot after 55 or 65s. About one minute; but clearly way longer than 42 or 47s found on forums. It started directly to some rescue mode, then, started to boot normally, without doing anything. Just released buttons during the first white screen. After booting, I have a normal phone. Did not need to perform any action. During boot, the phone had 2% batt, and was charging normaly. But, the charger LED remained off; I waited 5mn, untill I got 4%, unplugged the charger, replugged, and then got the orange LED.
Remember that your M8 can accept up to 9V on input. QC2 Chargers are really faster: with 9V 1.5A, you can charge your M8 from 0% to 100% in 95mn, even if you are intensively using it (gaming, wifi, GPS). Next gen phone will accept 12V. Even if manufacturers ignore that. HTC buys chips, and don't fully read specs. Aukey chargers are more powerfull and better reliable than official HTC ones.
Remember that many "slow charging" issues are in fact due to bad cable: charger is good, phone is good, but cable in between has high gauge copper, too thin wires, and produces voltage drop between plugs. HTC phones require 4.4V at the plug.
Remember that M8 and most modern phones (same for Samsung) are now MHL (wrongly called OTG): they are true USB hosts; you can plug any device on your phone; just buy an MHL (OTG) cable for 4 euros, and then a USB hub, and then any device: mouse, keyboard, USB monitor, ethernet dongle, SATA adapter, CF-uSD adapter ... and for 12 euros you have HDMI converters. Modern smartphones are real computers. Use them.

Categories

Resources