Related
Okay so my daughter grabbed my phone and threw it in the toilet. I had an Otter Box on it and it boots up fine and goes to sense. It's rooted. The problem is when it loads up sense it automatically loads up Car Home. I can close that and everything seems to work fine. Whem I power down the device I click "Power Down" and it shuts off and automatically reboots. I cant get it to just power down and stay off. Can somebody please help me?
LedGrip said:
Okay so my daughter grabbed my phone and threw it in the toilet. I had an Otter Box on it and it boots up fine and goes to sense. It's rooted. The problem is when it loads up sense it automatically loads up Car Home. I can close that and everything seems to work fine. Whem I power down the device I click "Power Down" and it shuts off and automatically reboots. I cant get it to just power down and stay off. Can somebody please help me?
Click to expand...
Click to collapse
Yikes thats no good. I would immediately take the battery out. Put the phone in a ziploc bag with dry white rice. Leave it in there for a day or so, I would say. The rice will absorb some moisture. You want to get it dried out as much sa possible before you try powering it on again. You'r sd card might have been damaged too. If the phone still doesn't work right after thoroughly drying it out, you may be SOL. The water damage indicators are now activated, and the warranty will be voided. If you have insurance, it will cost you a hundred bucks, for the deductible.
The most important thing now is to stop trying to power it on until the phone is dried out. Things will short out.
k2buckley said:
Yikes thats no good. I would immediately take the battery out. Put the phone in a ziploc bag with dry white rice. Leave it in there for a day or so, I would say. The rice will absorb some moisture. You want to get it dried out as much sa possible before you try powering it on again. You'r sd card might have been damaged too. If the phone still doesn't work right after thoroughly drying it out, you may be SOL. The water damage indicators are now activated, and the warranty will be voided. If you have insurance, it will cost you a hundred bucks, for the deductible.
The most important thing now is to stop trying to power it on until the phone is dried out. Things will short out.
Click to expand...
Click to collapse
Alright well I dont have rice. And my girlfriend has the car. I will try to go to the sprint store and see what I can do about replacing it. I need my EVO!! Oh and the cameras dont work now either. FML. I just got this phone about 3 weeks ago.
LedGrip said:
Alright well I dont have rice. And my girlfriend has the car. I will try to go to the sprint store and see what I can do about replacing it. I need my EVO!!
Click to expand...
Click to collapse
Yea, i hear ya. Who wants to keep their evo in a bag of rice overnight?! Just a warning though. There is a water damage indicator strip on the phone and the battery. That changes color when it gets wet, and thus that voids the warranty. I wouldn't expect Sprint to replace it for you, unless you have insurance, but then it'll cost a 100 dollar deductible. Good luck man, hopefully your sprint store has some cool employees.
LedGrip said:
Alright well I dont have rice. And my girlfriend has the car. I will try to go to the sprint store and see what I can do about replacing it. I need my EVO!! Oh and the cameras dont work now either. FML. I just got this phone about 3 weeks ago.
Click to expand...
Click to collapse
like kbuckly says.
and if you take it in rooted, they may not honor the warr, as well as the water indicator. eeek. seriously, try the rice trick. ive saved several of my daughters phones that way (I also dont buy her nice phones anymore. )
Yeah, Sprint will still look at it to determine if water damage was indeed the result of the phone acting up, even if the water markers show water contact. IF you can find rice, try that. If not, let it dry and / or take it in and hope for the best. Sorry to hear about it.
Number one rule when your phone gets wet: DO NOT TRY TO TURN IT ON!!! There is obviously water inside the phone. If you try to turn it on when its still wet, you will fry the boards. You needed to COMPLETELY dry the phone for at least 2 days, if not more, then try it.
Unfortunately since you tried to turn it on, you probably fried something on the board. Unless you have insurance, sprint wont fix a water damaged phone. And yes, they can tell it was water damaged.
Well It was on when she dropped it in the toilet So that alone probably fried it... so far everything has worked on it except the cameras and the fact that it reboots rather than shutting down.. Im not sure if I have insurance or not I have to check. But I dont want this phone if I can't use one of it's key features, It's camera's. I also don't want a phone that wont turn off. How much would it cost me to just buy another one out rite from the store without a contract, Because I already have a contract.
This really sucks because I just bought the thing like I said three weeks ago. And now it's ruined. Anyways I just have to accept it hang my head. Thanks for the advice but Im pretty sure there is no salvation for this phone. Which is sad because It was my buddy. Went everywhere with me. Now it's just spare parts. Poor Evo. RIP
I found out that I have to file a claim affidavit and include a copy of my ID and fax it to "phoneclaim". What a bunch of B.S. I dont see why they make you go through so much **** just to use a service that YOU pay for. It's so ridiculous. FML
LedGrip said:
I found out that I have to file a claim affidavit and include a copy of my ID and fax it to "phoneclaim". What a bunch of B.S. I dont see why they make you go through so much **** just to use a service that YOU pay for. It's so ridiculous. FML
Click to expand...
Click to collapse
Yea, water damage sucks man. Not a lot you can do. You may find a reasonably priced Evo in your area on craigslist perhaps.
Sent from my PC36100 using XDA App
k2buckley said:
Yea, water damage sucks man. Not a lot you can do. You may find a reasonably priced Evo in your area on craigslist perhaps.
Sent from my PC36100 using XDA App
Click to expand...
Click to collapse
yea, they are actually cheap, if you can be patient. I got a used one little less than a month ago (got it used instead of new for a very specific reason), paid 225 for it. if you can wait 'til the end of the month, lots of people that need cash for rent will be getting rid of them. (just be carefull about ESN, of course)
Im just gonna see how the Claim works out for me. need my Evo Back :'(
LedGrip said:
I found out that I have to file a claim affidavit and include a copy of my ID and fax it to "phoneclaim". What a bunch of B.S. I dont see why they make you go through so much **** just to use a service that YOU pay for. It's so ridiculous. FML
Click to expand...
Click to collapse
I had to do the same thing. It took me a week and a half to get a replacement for a line on my account.
Sent from my PC36100 using XDA App
Many One X owners, including me, has be having from display/screen issues that are quite annoying. And apparently, none has a definite answer as to what the main cause is. hTC has exchanged all those faulty devices, claiming it's a "hardware" issue...while in fact, it's their stupid back covers...i'll explain as we speak.
First, to know what screen/display problem i'm talking about, please refer to this Video.
Few days ago, i got my hands on a "Dead" One X...but i just refused that fact...because it just works! but no screen....screen is always blank....can touch it, go to dealer and make a phone call even. Sometimes the screen turned, sometimes, and it was like in the video, exactly like it.....so what's the problem?!
yesterday, i'll be honest, i got mad at this phone and held it with a tight grip...my finger happened to press just above something...and the screen turned on! worked great in fact! i was astonished! it just worked....but, oops, i turned off screen, then when wanting to turn it back on...blank...
I kept pushing on the back casing of the phone, trying to find the same place that made the screen turn back on...and viola, same place pressed on, screen back on.
Wanna know what's causing all of this?
Here you go:
Click me!
And those connectors Should be in good contact with this on the back cover
Click me too!
But you know, hTC ****ed this one up, just like it does on most devices with connectors on the back cover...*sigh*...like the sensation for example...
So what to do now?
i tried a bunch of things, and almost broke those connectors with a stupid thick aluminum foil on top of them...
also i tried bending them up, but that doesn't help either, as when the cover pushes them down, their shape will change and well...didn't work.
i also tried putting aluminum foil on the metal connectors on the actual cover...didn't help as well!
it seems only pushing on it from outside does the trick!!
i also tried pushing on the connectors together while the back casing is off, didn't work...as it seems there must be a triple connection...board, connectors, and cover...
I think the only solution would be with a new back casing? but...if hTC f****d it up with this one, wouldn't all back casing suck too?? or is this a manufacturing problem that the connectors are just short and won't connect well?!
here are pictures of how the phone turned on magically after pressing over that connector, and another of how the screen gets messed up when the, well, there's not a good connection...Thank you hTC!
Sample 1 Sample 2
Tomorrow i will buy a new back casing and report if that helped me or not.
I only came to this because i have no warranty...if you have warranty, please consider an exchange!
Oh, and finally, i was able to get into bootloader, first time i saw that screen! always has been blank!...pushing on the connector also did the trick.
Finally!
Soooo...comments?
If anyone has an idea on how to make the back casing come in better contact with those connectors, please let me know.
UPDATE
Hmm, why did you put this into Q&A?
what? in a bad mood and wanna bash me?
where should i put it then? as people with such problem would come ask here, am i right?
EDIT: lol, it's all good now ^^
arabology said:
what? in a bad mood and wanna bash me?
where should i put it then? as people with such problem would come ask here, am i right?
Click to expand...
Click to collapse
Well nah, would post it into General , as this was more like a guide. I wasn't bashing.. and not in a bad mood... If anything I bumped your thread up...
Also wanted to say that those contacts and that case seems to be f..cked up in general. As next to those you have the WIFI ones which in another thread, thats in General is shown how to fix...
My first comment was a compliment and you could clearly see I was smiling as I am on my avatar smiling. No reason to get defensive...
PAGOT said:
Well nah, would post it into General , as this was more like a guide. I wasn't bashing.. and not in a bad mood... If anything I bumped your thread up...
Also wanted to say that those contacts and that case seems to be f..cked up in general. As next to those you have the WIFI ones which in another thread, thats in General is shown how to fix...
My first comment was a compliment and you could clearly see I was smiling as I am on my avatar smiling. No reason to get defensive...
Click to expand...
Click to collapse
oh well...also WIFI connectors are bad?...no wonder SIII is flying and hTC is dying...
anyway, maybe a moderator can take this thread to the general forum, thanks for pointing those things out!
and sorry i seemed mean, but many, really, many users have nothing better to do but nag...trolls
thanks ^^
Soldering would fix this!
putting two round solders on the gold plates of the back cover. i will try that tomorrow. but i fear they would squash the connectors on the board? as that's what happened when i used two tiny balls of aluminum foil....one connector got squashed by it and i had to push it back up and play with it to make it look normal again.....hmmmm
arabology said:
Soldering would fix this!
putting two round solders on the gold plates of the back cover. i will try that tomorrow. but i fear they would squash the connectors on the board? as that's what happened when i used two tiny balls of aluminum foil....one connector got squashed by it and i had to push it back up and play with it to make it look notmal again.....hhhhh
Click to expand...
Click to collapse
Moved to general forum hope youll fix it bro...
So it is a hardware fault,would never guess that...in the general forum you have a topic with the name "wifi fault" give a look on that
Sent from my HTC One X using XDA
muamers said:
Moved to general forum hope youll fix it bro...
So it is a hardware fault,would never guess that...in the general forum you have a topic with the name "wifi fault" give a look on that
Sent from my HTC One X using XDA
Click to expand...
Click to collapse
*nods* already took a look at that
will try the soldering...or connecting a wire between both connectors...one of those should work
arabology said:
*nods* already took a look at that
will try the soldering...or connecting a wire between both connectors...one of those should work
Click to expand...
Click to collapse
Like you guys would say: "inshallah" :d
Just dont rush with the opening and be carefull
Sent from my HTC One X using XDA
waw another fellow citizen
so before we go ahead and go
doooom gloooom htcccc suxxxxxxx
lets first affirm tons of people have no problems with their wifi and their screens
so yes those connectors issues whether screen or wifi are another forum of a manufacturing defect, things might not be perfectly aligned and hence the issue
the flickering issue your thread title suggests finding the source of, isnt related to this, 90% of the corruption we saw out of box on the HOX turned out to be software including the back-light flicker which HTC fixed by readjusting the LCD voltage
moving on to your question a new back cover might very well fix it unless the misalignment is on the board
but im wondering why is this pin related to the screen to begin with? the Sensation didn't have such a pin you could remove the back cover and the screen kept operating, also the disassemble photos that were posted for the HOX showed the board and screen running perfectly without the back cover
as for the stupid copper foil, make sure you don't loose it unless you are planning to make a bomb its added to distribute Tegra3 heat
arabology said:
*nods* already took a look at that
will try the soldering...or connecting a wire between both connectors...one of those should work
Click to expand...
Click to collapse
Before you do that, please check the WIFI thread. There was already one member that described that soldering or adding a wire might be possibly harmful in the long run.
Changing the electricity stuff, how its called, the resistance or something (for the antenna though)
I'm having the same damn issue (check the picture) and thanks to Arabology for the well explanation on the problem. what I did was to send my phone to the service center and they told me it will take 3 working days (today was just the 1st day) for the technician to diagnose the fault and decide whether to replace the device or to repair it.
given that its a well known defect - should I just demand an exchange for a new device just incase if they revert that they repaired my phone? because I am sure the chances for the problem to reoccur is high.
Also just so you know I purchased this phone only about 3 months ago in HTC roadshow launch of OneX in Malaysia. HTC needs to come out with really quality products otherwise they will loose all their customers to samsung & apple (I believe they already lost major % of their loyal customers to their rivals)
oh well hope to get a good news soon. will keep u guys posted.
Update:
well, My One X is just cursed, few days ago it feel off my hand and the screen got cracked. now i'm waiting for my local repair station to get hold of a One X digitizer.
ALSO, HUGE NEWS, seems i was wrong. it's not the connectors. it's the whole part where there is a copper kinda sheath over it...i guess that's where are the cores are plus the Nvidia Tegra chip??! turned out, when i push there, that the screen lights up. at first i thought it's the connector, coz that's the most reasonable right?
what could be wrong under that? well, that place can be taken off, there's a metal housing that can be lifted off....idk, nothing seems wrong there...but seriously, just a slight push lights up the screen! so now i'm using the oldest trick in the book, i put a wrapped paper at the back of the casing, just where it will push over the place i talked about, and now screen is always on....just this small push does the job!! no more flickering!
i repeat, it's not the connector nor the back casing.......only God and hTC knows what's going on...
i did further investigations and tried to relate the "push" to any connections that could be on the board from the other side, but after disassembling the phone, there does't seem to be anything on the other side of the board that needs that certain force to help the screen to light up....idk, this just boggles the mind.
...anyone has any clue?!?
BTW, phone is working great even with the cracked screen, playing Dark Meadow just fine
walker07 said:
I'm having the same damn issue (check the picture) and thanks to Arabology for the well explanation on the problem. what I did was to send my phone to the service center and they told me it will take 3 working days (today was just the 1st day) for the technician to diagnose the fault and decide whether to replace the device or to repair it.
given that its a well known defect - should I just demand an exchange for a new device just incase if they revert that they repaired my phone? because I am sure the chances for the problem to reoccur is high.
Also just so you know I purchased this phone only about 3 months ago in HTC roadshow launch of OneX in Malaysia. HTC needs to come out with really quality products otherwise they will loose all their customers to samsung & apple (I believe they already lost major % of their loyal customers to their rivals)
oh well hope to get a good news soon. will keep u guys posted.
Click to expand...
Click to collapse
i say you should demand an exchange. hopefully the device they'll give will be of a different tier of products that doesn't have that silly, unknown problem.
also, i'm pretty well sure that they won't repair your device. as i read many users regarding this issue, all of them got an exchange......seems pretty messed up. and i doubt my paper trick will hold long before this issue comes back
PAGOT said:
Before you do that, please check the WIFI thread. There was already one member that described that soldering or adding a wire might be possibly harmful in the long run.
Changing the electricity stuff, how its called, the resistance or something (for the antenna though)
Click to expand...
Click to collapse
now that i have a paper inside my back casing, i can see that my WIFI connection is not at it's best, because of the extra space it took. so i'll most probably solder all the connectors
arabology said:
Update:
what could be wrong under that? well, that place can be taken off, there's a metal housing that can be lifted off....idk, nothing seems wrong there...but seriously, just a slight push lights up the screen! so now i'm using the oldest trick in the book, i put a wrapped paper at the back of the casing, just where it will push over the place i talked about, and now screen is always on....just this small push does the job!! no more flickering!
i repeat, it's not the connector nor the back casing.......only God and hTC knows what's going on...
i did further investigations and tried to relate the "push" to any connections that could be on the board from the other side, but after disassembling the phone, there does't seem to be anything on the other side of the board that needs that certain force to help the screen to light up....idk, this just boggles the mind.
...anyone has any clue?!?
BTW, phone is working great even with the cracked screen, playing Dark Meadow just fine
Click to expand...
Click to collapse
there was some guy, who posted a youtube video of when he pushed a certain area of his screen (the front part), it would switch off!
It only did it when pushed in that area, it was literally like a second power button.
Sorry I don't know exactly what it was, just the fact that somebody else had a similar problem!
HTC repaired my phone as the screen was faulty, it had a yellow tint, when i sent it for repair it did have screen flickering, ever since its come back, with a new screen, i rooted it and also put in the NEW ARHD rom, 2.05.2 base or something, it has stopped flickering :fingers-crossed:
walker07 said:
I'm having the same damn issue (check the picture) and thanks to Arabology for the well explanation on the problem. what I did was to send my phone to the service center and they told me it will take 3 working days (today was just the 1st day) for the technician to diagnose the fault and decide whether to replace the device or to repair it.
given that its a well known defect - should I just demand an exchange for a new device just incase if they revert that they repaired my phone? because I am sure the chances for the problem to reoccur is high.
Also just so you know I purchased this phone only about 3 months ago in HTC roadshow launch of OneX in Malaysia. HTC needs to come out with really quality products otherwise they will loose all their customers to samsung & apple (I believe they already lost major % of their loyal customers to their rivals)
oh well hope to get a good news soon. will keep u guys posted.
Click to expand...
Click to collapse
Finally found someone with the exact same problem. I haven't been able to use my hox properly for weeks. Think I need to be sending back to HTC
Sent from my X10i using XDA
Finally I've got my OneX replaced with a new unit.:laugh: Hoping this will not have any sort of hardware faulty anymore.
interestingly. while waiting for my turn in the service center, I was just talking to a guy sitting and waiting beside me who came to report a problem with his OneX
and apparently its his 4th time visit to the service center. And all his previous 3 visits ended up with his OneX getting replaced each time....and each time with a different hardware issue (screen flickering / dead pixels / color faulty). Oh man....I thought the OneX was the best quality product from HTC.
and now I'm having a slight regret that I shud have just waited for another 2 more months and bought the SIII instead. God knows what other problems my OneX is going to come up with.
Hi
arabology said:
Update:
well, My One X is just cursed, few days ago it feel off my hand and the screen got cracked. now i'm waiting for my local repair station to get hold of a One X digitizer.
ALSO, HUGE NEWS, seems i was wrong. it's not the connectors. it's the whole part where there is a copper kinda sheath over it...i guess that's where are the cores are plus the Nvidia Tegra chip??! turned out, when i push there, that the screen lights up. at first i thought it's the connector, coz that's the most reasonable right?
what could be wrong under that? well, that place can be taken off, there's a metal housing that can be lifted off....idk, nothing seems wrong there...but seriously, just a slight push lights up the screen! so now i'm using the oldest trick in the book, i put a wrapped paper at the back of the casing, just where it will push over the place i talked about, and now screen is always on....just this small push does the job!! no more flickering!
i repeat, it's not the connector nor the back casing.......only God and hTC knows what's going on...
i did further investigations and tried to relate the "push" to any connections that could be on the board from the other side, but after disassembling the phone, there does't seem to be anything on the other side of the board that needs that certain force to help the screen to light up....idk, this just boggles the mind.
...anyone has any clue?!?
BTW, phone is working great even with the cracked screen, playing Dark Meadow just fine
Click to expand...
Click to collapse
Probably what's referred to as a dry joint or some other connection not connecting very well, not uncommon in electronics.
You need to get it repaired or replaced, simple as that. If it is a dry joint under one of the chips that use a ball grid array of solder points, you will never be able to sort that out yourself and it would be scrapped more than likely rather than a repair attempted for such a fault. To repair, it would need to go into a special over to heat it enough to melt the solder under the chip. Exerting pressure will just eventually make things worse as you can end up fracturing more of the soldered connections as there is little give to resist flexing.
Regards
Phil
Ok, so I got stuck in the dreaded stuck power boot loop. After mashing the button for a bazillion times, blowing on it, spraying it, hitting it with various objects, it worked! And so far it has been working. But I don't want anything like that to happen again, where it will just shut off on its own due to its own crappieness.
Can you disable the power button, so that the only way to turn off the phone is by using power tools or some other widget?
I want nothing to ever happen when I press it, or when it decides to magically make contact with the inside of my phone.
I can't get inside the phone to deattach the connectors, because here is me -----> (O.O) here is my screwdriver ------> [=====+ and here is the screwdriver tip when I tried to open the phone ------> *snap*
So I now have a screwdriver tip stuck in one of the screws, and I am locked out of its innards, which may be a good thing
Any way to modify the code to disable the power button?
Please help! My phone went bananas again and after shaking it around I got it working again. This is an urgent matter, I can't use my phone like this.
It sounds like you tried most of the stuff in this thread already:
http://forum.xda-developers.com/showthread.php?t=1931310
If nothing there works you may have to send it off for repair.
Ach! Do I have to unroot PA and reset the flash counter if I give it to T-Mobile? My phone is a refurb, it's replacing a broken, really old HTC that no one makes anymore. What a hassle! All for one tiny defect with HUGE consequences! I am still under warranty. I don't know of any good local phone repair shops here in Hawaii, may have to mail it in.
FML, today's my birthday, and I may have to pay for another phone.
Babbalabba said:
Ach! Do I have to unroot PA and reset the flash counter if I give it to T-Mobile? My phone is a refurb, it's replacing a broken, really old HTC that no one makes anymore. What a hassle! All for one tiny defect with HUGE consequences! I am still under warranty. I don't know of any good local phone repair shops here in Hawaii, may have to mail it in.
FML, today's my birthday, and I may have to pay for another phone.
Click to expand...
Click to collapse
Well, at least you are still under warranty. I am not sure what happens when you send it to T-Mobile. Hopefully someone with experience with that can chime in.
Good luck and happy birthday.
meekrawb said:
Well, at least you are still under warranty. I am not sure what happens when you send it to T-Mobile. Hopefully someone with experience with that can chime in.
Good luck and happy birthday.
Click to expand...
Click to collapse
Heh, been eyeing the nexus 4, even with its flimsy back. I can always get a case.
Yeah, hopefully it doesn't decide to go bonkers on me again. So far it has not been turning itself off and on or getting itself stuck down, but you never know...I'll see what my options are from here on out.
Babbalabba said:
Ok, so I got stuck in the dreaded stuck power boot loop. After mashing the button for a bazillion times, blowing on it, spraying it, hitting it with various objects, it worked! And so far it has been working. But I don't want anything like that to happen again, where it will just shut off on its own due to its own crappieness.
Can you disable the power button, so that the only way to turn off the phone is by using power tools or some other widget?
I want nothing to ever happen when I press it, or when it decides to magically make contact with the inside of my phone.
I can't get inside the phone to deattach the connectors, because here is me -----> (O.O) here is my screwdriver ------> [=====+ and here is the screwdriver tip when I tried to open the phone ------> *snap*
So I now have a screwdriver tip stuck in one of the screws, and I am locked out of its innards, which may be a good thing
Any way to modify the code to disable the power button?
Click to expand...
Click to collapse
I can tell u from a friend that works for tmobile service department that when u send it back for repair they most likely won't even turn it on, especially with your issue all they'll do is their it in the refurb pile and send ua new "refurbished" phone so no it won't matter if u leave it rooted, your going to get a different phone back anyway unless u personally bring it to a 3rd party repair place
Sent from my SAMSUNG-SGH-T989 using xda premium
The power button's function is hardware based. No way to disable via software.
Hi Guys,
A month or so ago my mom dropped her S3 into the toilet. I told her to put it in rice ASAP and I believe a day or so later she did (but perhaps later that night). When I turn the phone on, the blue SAMSUNG (or maybe it says Galaxy) logo comes on and shows up completely fine, but nothing else after that works.
The lights around the phone work as well, including when I hit the menu and back buttons on the bottom part of the phone. It vibrates properly when it should and I also get sound, no problem.
I've tried connecting the phone to my computer to salvage pictures and data but it doesn't recognize the device for some reason.
Is the phone completely toast or is there a way for me to fix it? It was in very good condition before this and had only been used for a year.
Thanks a lot for the help. Any advice is greatly appreciated.
Update: I just turned it on again and I could see the FAINTEST traces of the home screen. I pulled the settings down and turned the screen brightness up all the way and I can make out everything. The phone seems to be fully functional, but the screen is still incredibly dark. Any ideas on what is broken and what I need to fix?
Once every while it flickers to the full brightness for a split second and then goes back to dull.
Digitizer may have water. See if someone can take it out and wipe it down. Otherwise its a insurance call.
Thanks for the reply. I have no insurance on the phone so that's not an option. Would it be ultra difficult for me to try and take out the digitizer and wipe it down? Is it far too late to try and dry it out more with rice or silicate packs?
Please see this thread. Perhaps you can compare notes.
Perseus71 said:
Please see this thread. Perhaps you can compare notes.
Click to expand...
Click to collapse
Is there a way to confirm it's the digitizer before I pay $120 to try and transplant a new one into the old phone? I am also not very savvy at phone repair, although I could probably hire someone locally to do it.
Would like to make sure it's the digitizer first though.
I've also heard that re-dropping it in distilled water and then drying it with silicate gel packs might help clear whatever issues it's experiencing now. That seems crazy to me. Thoughts?
Thanks!
I wouldn't drop it again in water. If you are not sure you can do it, then better send it for Out-Of-Warranty Repair. I can't tell you of a way to determine if its the Digitizer or not.
I "think" its your LCD having some dampness.
Okay, thank you. So assuming it's the LCD being damp, is it far too late to use silicate packs to bring out the moisture? Or is it time to pull it apart and wipe it down?
Also the videos I see online kind of make it seem like you can't remove the screen without breaking it.
Yes give it a try. A friend of mine, tried that successfully. Your mileage may vary.
Perseus71 said:
Yes give it a try. A friend of mine, tried that successfully. Your mileage may vary.
Click to expand...
Click to collapse
I followed a video tutorial online and took it apart and brushed it with a toothbrush dipped in 99% isopropyl alcohol. I let it dry for a bit and retried it and the screen was still very dark. :-/ I guess I'll try it again later.
Ok, what happened here is my phone went to swim with me crying.
I tried to dry up the phone, but I still can't turn it on. Then, I send my phone via my carrier (Rogers Canada in my case) for repair. Of course, I am pretending to be innocent saying I don't know what happened to my phone, and I just can't turn it on. Then HTC (I suppose it is some outsourced place, but should be licensed under HTC) told me that there are COLLISION on the mother board and somewhere else, which is ridiculous. There is one much more ridiculous thing: the repair is going to cost
$1000
Of course, I am not asking them to repair for me. I just want to share how ridiculous it is, and if you guys can gimme some hints on how I can have it repaired, that will be great.
your phone CANT be repaired. It got wet. end of story.
what you need is a new phone.
I bet he meant corrosion on the main board. Also i personally dont like to read posts where people know they got the phone wet then try to play dumb and pull one over on someone or a company. That shows very little integrity on your part. But i dont want to turn this into a personal attack as the mods dont like it. SO lets hope a mod reads this thread and shuts it down.
If you're lucky the phone might magically just turn on, on any given day. I've seen that happen
Sent from my HTC One_M8 using Tapatalk
IAmSixNine said:
your phone CANT be repaired. It got wet. end of story.
what you need is a new phone.
I bet he meant corrosion on the main board. Also i personally dont like to read posts where people know they got the phone wet then try to play dumb and pull one over on someone or a company. That shows very little integrity on your part. But i dont want to turn this into a personal attack as the mods dont like it. SO lets hope a mod reads this thread and shuts it down.
Click to expand...
Click to collapse
I accept your comment, but what I wanna say is $1000 is ridiculous...
I will agree with you there, 1000 bucks to fix a phone is way overboard. Unless theres some conversion were missing. like 400 USD = 1000 what ever lol
IAmSixNine said:
I will agree with you there, 1000 bucks to fix a phone is way overboard. Unless theres some conversion were missing. like 400 USD = 1000 what ever lol
Click to expand...
Click to collapse
It's 1000 CAD, which equals around 930 USD.
This doesn't even sound right. How can the repair cost more than the actual cost of the device. I'd look for another repair option.
Sleepycloud said:
This doesn't even sound right. How can the repair cost more than the actual cost of the device. I'd look for another repair option.
Click to expand...
Click to collapse
Diagnostics, manual assembly, etc. Very little can be reliably salvaged from a water damaged phone. Assume everything but the case needs replacing. It's what's known as a write-off.
BenPope said:
Diagnostics, manual assembly, etc. Very little can be reliably salvaged from a water damaged phone. Assume everything but the case needs replacing. It's what's known as a write-off.
Click to expand...
Click to collapse
I've washed them full cycle several times. Each time when I found my phone i soaked them in alcohol and agitated them for about 20 minutes fully submerged. Then I use a toaster oven and dried them out with gentle heat and by sucking air into the phone about 20 times. All of them worked again. Even an iPhone once. Yes, I said full cycle. I found my phone in the when I was loading the dryer. Have I been lucky? I dunno. Many find this hard to believe, but it's true. I put a charging port in my girlfriends note 2. It came from a water damaged Note 2. It was sitting in parts for 2 months. I figured it was dry because it was sitting in open air. Well I put it in and it worked. A week later she lost data and voice. Long story short, that chargign port wrecked everything in the Note 2. When they opened it up, it has white fungus looking corrosion working halfway up the phone in three spots. It absolutely ruined the Note 2 and an insurance claim had to be made. It can go ether way, saved or junked. Just depends on the conditions.
Sleepycloud said:
I've washed them full cycle several times
Click to expand...
Click to collapse
Wow, I guess you don't learn fast.
Water damaged vs got wet.
If you're quick enough and use the correct method and lucky, you may get the thing working again, but I'd hardly say reliably. HTC or any repair centre are hardly going to want to provide a 3 month warranty on a repair of a phone that's got wet without replacing everything that can be damaged by water.
The sum of the parts is greater then the price of the item.
Thats why we have chop shops. Some cars are worth more when parted out and the pieces are sold individually.
So if each component was being sold to him at retail pricing, add labor and whola, higher price.