Related
Got a little problem, maybe big =(
Basically the phone one day decided not to work
i can get only two screens
either the start-up splash screen displaying CINGLAR and the firmware stuff on the bottom corner
or
if i enter bootloader mode, i get SERIAL 2.07 and nothing else
i have tried hard reset, take out the battery for ever, even flash
hard reset does nothing, soft does nothing
take out the battery does nothing
the phone won't charge through the cradle or charger, i can only charge the battery alone using the cradle
as for flashing it won't flash in the cingular splash screen or the bootloader screen, it doesn't change from SERIAL to USB when connected, thus the computer can't send anything to it
what can i do ?????
Do you have an SDIO card in the top slot? That can cause problems with the bootloader accepting the image from the PC.
nope only have the original DEMO SD plastic
any one what could be wrong ?
had same problem
dont know if you are doing the wm5.0 hard reset or teh old style hard reset that we used to on wm2003se. its teh notes button, camera, power and soft reset button. clear registry and the storage and then it should work. it did for me.
tried your reset steps boots the bootloader =(
Re: BA - SX66 Variant won't load - stuck in Splash or Bootlo
evilgabbie said:
if i enter bootloader mode, i get SERIAL 2.07 and nothing else
...
what can i do ?????
Click to expand...
Click to collapse
BigDamHero said:
If you got bootloader mode then you should be able to upgrade your rom to whatever you like.
Step by step insturctions are on WIKKI. The page for upgrading to the most recent ROM for the Blue Angel that IS NOT WM2005 is here:
http://wiki.xda-developers.com/index.php?pagename=BA_1.40.00_Upgrade
If your device is in bootloader mode just put it in the cradle (activsync won't start but don't worry about that) and start the upgrade!
Click to expand...
Click to collapse
When you get to the Bootloader screen, probably you are home free. Just use the abouve link to resolve you problem.
BootLoader Loop Issue - SX66 Siemens
I am having a similar issue , where i am unable to hard reset or soft reset ,If I place SX66 (SIEMENS) in cradle it appears to charge after charge is complete , it will go to bootloader menu.
==========================================================
I have downloaded the MTTY , and would to know the settings required for USB , is selected from dropdown what is the optimal choice to make.
Im not seeing the cmd line " CMD> " in using MTTY.
I was gonna use com ports but dont know the settings to set:
==========================================================
parity
data bits
stop bits
flow control
local echo
http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
had exactly the same problem, follow these steps for hard reset
my phone came good after (running wm6)
I am a rookie at upgrading this stuff. I have a QTEK 9000. I got UNI_QTEK_13077_176_10900_WWE_Ship.exe from the ftp site.
1) Did a device reset.
2) Connected via active sync.
3) ran the program.
After a short period, The device shut off and active sync disconnected.
The screen is black. On button does not work.
I tried a hard boot and I get the boot menu and 0 or x does not seem to do anything.
Did I do something wrong? What now.
GaryK2 said:
I am a rookie at upgrading this stuff. I have a QTEK 9000. I got UNI_QTEK_13077_176_10900_WWE_Ship.exe from the ftp site.
1) Did a device reset.
2) Connected via active sync.
3) ran the program.
After a short period, The device shut off and active sync disconnected.
The screen is black. On button does not work.
I tried a hard boot and I get the boot menu and 0 or x does not seem to do anything.
Did I do something wrong? What now.
Click to expand...
Click to collapse
I think that program is supposed to be run after you've removed USB from the connection methods in activesync - i.e. you're not connecting via activesync, even though the device is physically connected.
OK, I tried the process again without activesync.
That seems to be the answer. ROM Is now installed. I just have to finish up.
Thanks alot,
That scared the hell out of me.
GaryK2 said:
OK, I tried the process again without activesync.
That seems to be the answer. ROM Is now installed. I just have to finish up.
Thanks alot,
That scared the hell out of me.
Click to expand...
Click to collapse
Hehee... when you get the new rom on, you'll love it...
GaryK2 said:
OK, I tried the process again without activesync.
That seems to be the answer. ROM Is now installed. I just have to finish up.
Thanks alot,
That scared the hell out of me.
Click to expand...
Click to collapse
Sorry for my silly question but how can you process it without activesync, mean you have removed activesync form your conputer?, because my activesync is automatic running when the computer start up
Thanks,
Orangevn
orangevn said:
Sorry for my silly question but how can you process it without activesync, mean you have removed activesync form your conputer?, because my activesync is automatic running when the computer start up
Click to expand...
Click to collapse
You're just telling AS to ignore the Exec when it's connected. The PC itself still sees it and adds a driver on connection. So you're not removing AS from the PC as such.
i have same problem but it doesn't work
please help me....this phone is dead now:-(
Re: i have same problem but it doesn't work
bmlsbr said:
please help me....this phone is dead now:-(
Click to expand...
Click to collapse
Did you try the AS thing above?
First off what do you on the screen of your device when you turn it on? Is it in boot loader screen, a black screen with text that says boot loader mode and serial?
If it is in boot loader screen and it says serial on the bottom, when you plug in the USB do you see the "serial" text change to "USB"?
I had this problem with mine. I upgraded my Qtek9000 with the new orange ROM and when the process finished I was still in the boot loader screen and could not get out of it. I had to re-flash it back to the Original Qtek ROM which revived the devices. I then started the ROM upgrade process all over again which resulted in a successful flash.
If you can answers some of the questions above I can try to help.
BTW, the upgrade process takes about 20-25 minutes. if it was any less then that you unplugged the device to early.
Plug device in.
• Start ROM upgrade process.
• The device will turn off and go into boot loader mode (the computer will lose connection to the device and unrecognized USB devices error will appear in your task bar).
• Wait until the device reconnects to the computer and the ROM upgrade starts.
• This process will take 20-25 minutes.
• Reset the device with option 0 (erase all data)
• The device will boot normally and go through the extended ROM application installs. It will ask you to reset again.
• After the second reset you are done.
xda exec upgrade (dead phone)
tHIS ALSO HAPPENED TO ME (IT WAS PRETTY SCARY) . i DISCOVERED THAT I COULD GET IT LIVE BY PRESSING THE LIGHT BUTTON THE POWER BUTTON AND THEN SOFT RESET (THIS IS THAT BOOT MODE) .
THEN I RE-CONNECTED TO MY PC AND RE COMMENCED THE UPGRADE...WORKED FINE. I HAD ACTIVESYNC RUNNING WHEN I DID THE INTIAL UPGARDE, PROPBABLY THE PROBLEM!! :wink:
none of this worked....may be I am not doing it right
when I try to add hard-reset all I get this is this:
"press 0 to restore factory default"
"press X to exit"
When I run the rom update, I get device connection problem error message and sometimes the country id error message.
none of this worked....may be I am not doing it right
when I try to add hard-reset all I get this is this:
"press 0 to restore factory default"
"press X to exit"
When I run the rom update, I get device connection problem error message and sometimes the country id error message.
my yahoo and msn id is bmlsbr...please someone chat with me and provide some help. I feel helpless after spending all the money and the phone dead after i day of use.
please...........
here is what I am getting
I can not turn my device on at all.
I'm unclear to what you are saying. First you tell us that the device does not turn on. Then you say you are getting the 0 X option. Which one is it? If you are getting the O/X option what do you see on the screen when you press 0. Do you see the device in boot loader mode? You might have to remove the battery and try the reset button after. my experience has been when the device is in boot loader mode I cannot turn it off. It always stayed on. So you might want to charge it just to make sure you have full power. I would also use the ROM loader without the country and device ID restrictions you can download it from the FTP site.
QTEK 9000 DEAD
I was always able to get the hardware reset menu..but nothing happened beyond that.
Now the phone is working after multiple tries to put the rom. But active sync won't work. Any clues????
What do you mean by works? Did you load the ROM?
Have you tried to follow these instructions:
http://forum.xda-developers.com/viewtopic.php?t=43592
Seems to work for a few people.
PLEASE HELP!!!
I try upgrade my Dopod 900 to WM6 by using http://micmeo.com/UNI/WM6/900_WWE_20...0_wwe_ship.zip, but after the upgrade success 100%, i disconnect the USB, and hard reset the PDA, then the PDA cannot bootup, it alwaus showing the black screen...
When i try hard reset again, i can see the display show option 0 to reset and option X to exit, but try both keys which back to the same black screen...
I also try press power+light+reset, but no responses at all... when i plug in the power cord, the light for charging not on as well...
PLS HELP....
dopod900xxx said:
PLEASE HELP!!!
I try upgrade my Dopod 900 to WM6 by using http://micmeo.com/UNI/WM6/900_WWE_20...0_wwe_ship.zip, but after the upgrade success 100%, i disconnect the USB, and hard reset the PDA, then the PDA cannot bootup, it alwaus showing the black screen...
When i try hard reset again, i can see the display show option 0 to reset and option X to exit, but try both keys which back to the same black screen...
I also try press power+light+reset, but no responses at all... when i plug in the power cord, the light for charging not on as well...
PLS HELP....
Click to expand...
Click to collapse
Try to enter the bootloader mode (power+light+reset). From what you have described it appears that you should not have problem entering the bootloader mode. Please remember that in bootloader mode yor screen is dark and only when you look very carefully you will be able to read the word "Serial" on the top of the screen and bootloader version number at the bottom. If there is inssuficient illumination in the room it is quite possible to think that the screen is blank. There will be no backlight. Once you are in the bootloader connect to your PC (before connecting please open Active sync on your PC uncheck the "Allow USB" connection in File / connection setting) Once connected the word "Serial" on the top of the screen will change to "USB". It is advisable to use only the original cable. Also connect the cable directly and not through a hub. Now reflash the rom and do a hard reset. I have faced problems by softreset after upgrade please try hard reset.
Hopefully your problem will be solved by a reflash.
Best of luck
From my past experience you have to flash to the original manufacturer rom first. Then you flash to whatever rom you want.
hope this helps
Thanks all, I'm now be able to re-flash the ROM and upgraded to WM6....
Here comes another issue... after i run the first setup and reset the PDA, it stuck on the Windows Mobile screen, any clue?
thanks again.
dopod900xxx said:
Thanks all, I'm now be able to re-flash the ROM and upgraded to WM6....
Here comes another issue... after i run the first setup and reset the PDA, it stuck on the Windows Mobile screen, any clue?
thanks again.
Click to expand...
Click to collapse
From the file link you have specified, http://micmeo.com/UNI/WM6/900_WWE_20...0_wwe_ship.zip it seems that you are using Jwrightmcps' WM6 2.01.08 WWE Rom Release.
I too have lock-up problems but only during boot-up. The frequency of this happenning is about 30% and why it happens is still unknown since the lock-up happens at random stages during the booting sequence. The only solution that I know of for now is to simply do a soft-reset repeatedly until the device boots up properly.
nvatvani said:
From the file link you have specified, http://micmeo.com/UNI/WM6/900_WWE_20...0_wwe_ship.zip it seems that you are using Jwrightmcps' WM6 2.01.08 WWE Rom Release.
I too have lock-up problems but only during boot-up. The frequency of this happenning is about 30% and why it happens is still unknown since the lock-up happens at random stages during the booting sequence. The only solution that I know of for now is to simply do a soft-reset repeatedly until the device boots up properly.
Click to expand...
Click to collapse
This appears to be a common problem as seen from different posts. Thankfully things are ok after reset.
yes, after reset few times, it works... and everytime it hangs, need reset few times...
dopod900xxx said:
yes, after reset few times, it works... and everytime it hangs, need reset few times...
Click to expand...
Click to collapse
You might find this of interest - it refers to the problem of hanging after soft reset in the 2.01.08 WWE Rom:
jmallen said:
I had this problem also. I found pulling out the battery for 5 or more seconds solved this for me every time.
Give it a try. Good luck
Click to expand...
Click to collapse
It may be solved in later versions.
d_ranade said:
Try to enter the bootloader mode (power+light+reset). From what you have described it appears that you should not have problem entering the bootloader mode. Please remember that in bootloader mode yor screen is dark and only when you look very carefully you will be able to read the word "Serial" on the top of the screen and bootloader version number at the bottom. If there is inssuficient illumination in the room it is quite possible to think that the screen is blank. There will be no backlight. Once you are in the bootloader connect to your PC (before connecting please open Active sync on your PC uncheck the "Allow USB" connection in File / connection setting) Once connected the word "Serial" on the top of the screen will change to "USB". It is advisable to use only the original cable. Also connect the cable directly and not through a hub. Now reflash the rom and do a hard reset. I have faced problems by softreset after upgrade please try hard reset.
Hopefully your problem will be solved by a reflash.
Best of luck
Click to expand...
Click to collapse
boss ... please help me ..... i have a dopod 900 ..... but it can not enter bootloader or hard reset .... ditancap usb cable, charger lights flash .... Please help keep the boss. ... thank you
Welcome to forums
Have a read on my signature link, you´ll find a lot of interesting information to recovery your Universal.
Good luck,
flash with tomal roms
Welcome to forums
Tomal ROM´s are indeed fast and stable
manybe you can nmsm your original rom again
Try update bootloader to 1.01 _ttp://rom-update.ru/programs/dd48795954c166e9431f4127c130d474.exe
German Qtek 9000 CID unlocked, hardSPL'd
running MaxStegiROM
Tried to upload D-Two's ROM.
Everything went fine, upload 100%
then: upload error.
screen went black, no reset works
no USB or Serial to be read on dark screen.
Tried battery out (battery is charged), no reaction.
When connecting to PC the red charging LED lights up for
some minutes, then goes off.
PC says connected unknown device ain't working properly
(other Qteks are recognized properly)
Trying to re-flash gives connection error when pressing "update".
Any idea?
Dear all,
i've got 2nd hand xda stealth for 2 weeks, now my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram with nb0 extension on miniSD. please any one can help me to recover my Stealth ?
sorry for my bad english.
xda stealth..
go to www.seeo2.com, download a rom upgrade utility from there.. then start upgrade procedure again. As xda stealth is a hybrid phone..dont try any custom roms on it..
thank's malhar for responding my thread.
i already download the upgrade rom from the o2 site (now is www.mwg.com), i put the rom to my SDCard, the problem is how can i enter the boot loader, in case my stealth always in blank screen with call and end button are light.
i already press press power + call + end button, but my stealth stuck on that condition. every method of flashing mode i already try but no response from my stealth.
Syaipul
oh yea malhar, for information i read the procedure for upgrading on o2 site that connect status is required for upgrading procedure in activecync, my stealth has disconnected status when i plug to my com. can i do the upgrade the rom in this case?
buddy, remove ur sd card from the device first..and then hard reset ur device by pressing reset button via stylus, then flag which is windows home key and then ok key..reset+flag+ok.. maintain the sequence..press reset first keep on pressing then flag and ok key.. it will format ur device.... then try to flash new rom on it
ok malhar, i'll try tomorrow. thanks.....1000x
sad-sad-sad
my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram on miniSD. please any one can help me to recover my Stealth
Your SPL boot loader sounds like it is gone, formatted...
You may be able to patch it, using scripts & mtty if you can get into DL mode. Sounds like you're stuck in OEMSBL though.
help me !!!!
i have try pressing flat and ok botton to format . but nothing appear on the screen . is the other way to format or upgrade rom .
• The device doesn't boot, I see only O2 logo. Hard reset doesn't help and the Firmware update process stops with the first message?
1. turn off the device;
2. enter engineering mode;
3. in Main menu choose Boot Config;
4. in Configuration menu choose EBOOT-Launch Image;
5. turn off the device;
6. now hard reset or upgrade firmware.
Sometimes helps another method: leave the device without the battery for about 30 minutes, then turn your O2 XDA Stealth on.
• How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings.
Click to expand...
Click to collapse
follow this thread from YUC wm6
http://forum.xda-developers.com/showthread.php?t=352468
blank screen
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
cant see o2 logo
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
randysng said:
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
Click to expand...
Click to collapse
Have you tried removing the battery for few hours ??? Does the engineering mode work???
engineering mode
engineering mode ? how to set engineering mode ?
randysng said:
engineering mode ? how to set engineering mode ?
Click to expand...
Click to collapse
How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
malhaar said:
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
Click to expand...
Click to collapse
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
khalifa_smart said:
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
Click to expand...
Click to collapse
It worked for me
Goto to your PDA setting and uncheck USB to PC.
Note: Check task before connecting to USB ensure no task including Active Sync.
FYI.
Im using VISTA Ultimate to update my XDA.
From WB 6.1 back to WM5. WM 6.1 too buggy and battery drained fast.
Cheers!
Please help me O2 stealth it dead not boot and blank screen .Are you Jtag for it please post it here.
i have the same problem --- my stealth is absolutely dead after using a cheap local charger
i have dismantled the board and taken some pics of the jtag connectors -- made the common LPT port jtag cable
how to proceed from here ?????
is the procedure similar to that of jtag recovery of a flame or an atom exec ??
how do i find the bootloader for O2 Stealth for flashing the NAND memomy Disk on Chip ??
please share your insights
Greetings,
I have done my research, but am now stuck. I have run into a roadblock every step of the way already. Activesync wouldn't recognize the phone, restored default settings and now it can see the phone. However, now the phone is in Japanese.
SDA unlocker has failed to work and I believe I need to hack two registry keys before I try it again. However, I am running into an error when trying to do it from my computer with the phone plugged in. The phone is also in Japanese so I can't run anything on it before the sim locked screen comes up.
Any suggestions? Or a quick step by step to change the language to English before the sim locked screen appears?
Thanks
Turn off SIM Card and Power On the dewice. Then try change language...