hi all,
i have a mda pro (htc 9000) from T-mobile, during wm5 and many bugs
i have tried to upgrade, i find some update rom overhere and followed the
instructions, direct during upgrade the device comes up in bootloader screen
en got stuck, i have tried everything even reset e.t. still i cannot get out
of the boatloader screen, i have tried an wm6 rom but i gaot the message
checking the information on your device and nothing is happend anymore
still waiting for a long time.
i have no idea
please help
thanks
Download an official Shipped ROM meant for your Universal and flash it. It should then pass through the screen.
thanks for the tip, i find the rom, but it need for upgrade active sync installed
and that's the issue now, because active sync does do nothing now when the device is in boatloader mode.
IT UPGRADING NOW pfffffffffffff
after intestalling again active sync...
oeps
Read Wiki!
Read Wiki.
Use mtty...DOC format.
Flash original WM5 ROM.
THEN
CID unlock with upgradeutility Noid.
You are free to do almost anything.
Again Read Wiki.
Read hdubli ...thread for stuck in bootloader.
Read Roms from Cotulla thread....it's helpful.
As long as you have intact bootloader , don't panic...it is not dead yet.
thanks for the advise, i find the wiki and solve the problem.
on my old xp pc and installed active sync, the device was direct upgraded
and the orginal rom is back to the latest version.
i find also the 6.5 rom but for now it works
Related
i urgently need your help with my htc prophet after I haven't found an answer in the portal already:
as my prophet (seller is vodafone) showed the vender issue when trying to upgrade i used the downgrade and unlock cid program i found here on the page. after step one, using the downgrade command my device no gets hung while start up, I can see the ipl/spl window, that's all. nothing will happen even after waiting an hour or trying to hard reset the device again. the os listed now is 1.0.13.21
my problem is that due this active sync doesn't recognize the device anymore, i cannot connect to it and as of this i cannot go on with installation...
need more info? please let me know!
troost said:
i urgently need your help with my htc prophet after I haven't found an answer in the portal already:
as my prophet (seller is vodafone) showed the vender issue when trying to upgrade i used the downgrade and unlock cid program i found here on the page. after step one, using the downgrade command my device no gets hung while start up, I can see the ipl/spl window, that's all. nothing will happen even after waiting an hour or trying to hard reset the device again. the os listed now is 1.0.13.21
my problem is that due this active sync doesn't recognize the device anymore, i cannot connect to it and as of this i cannot go on with installation...
need more info? please let me know!
Click to expand...
Click to collapse
i managed somehow to install the 02.47.11 rom, but it seems that the os isn't starting.
is it possible, that wm 5 got lost due the upgrade?
help, please
Hi All,
My P3600 is stuck in bootloader after trying to install the official D810 ROM. I used the CID unlock install first, which seemed to work fine, I then tried to install the D810 ROM and it looked like it was working, but stopped at 28% with some kind of communications problem. Recovery does not work... it displays the progress bar, but then goes straight back to the rainbow bootloader screen.
Any help or suggestions appreciated.
Thanks
Rael
Phew... got it working. I removed the battery and replaced, boot loader was still displayed, and then ran the old official WM5 update which seemed to progress from 0 to 100% sucessfully.
Thanks
Rael
Your phone was relocked by the update, and I'm guessing you don't have an actual D810 that's supposed to get this update. The best method to flash this is to follow my post here:
http://forum.xda-developers.com/showthread.php?t=316410
oops, you can use hard SPL in this link:
http://forum.xda-developers.com/showthread.php?t=299659
i got the problem like you when i upgrade my device to wm6 officiel.
After you flash hard SPL Olipro, you can use PC to flash again another rom you like.
(sorry for my worth english)...
People just do NOT know how to read...sigh.
Hello, just to start I will say that I'm completely new to PDAs, because I got my HTC TyTN a few days ago. So I had WM5 and I installed WM6 from http://forum.xda-developers.com/showthread.php?t=320829
But then I saw the Schap's WM6 Pro 4.20 Roms, which had TouchFLO installed and tried to install the full version, when it asked for Bootloader version I ticked the SP 2.02/2.10 (or whatever it was), because it was the closest to my Bootloader version - 2.03 (if I'm not mistaken). It started installing but after few seconds it displayed me some error. I don't remember what was the error, I only remember that it said that something was corrupted. So I would really appreciate any help installing Schap's WM6.
P.S As I said i'm newbie with PDAs, so please if you try to expain what should I do make it a bit more .... simple .
I'd suggest using the detect spl option when you try flashing. If you still get an error I would highly recommend posting the details so you can get the correct help.
There are several ways to get in touch with a new rom.
Please read the wiki, there should be everything explained.
Hermes Wiki
If nothing works there is only one solution for me, yet.
Then I have to change manually to bootloader mode and flash the original latest provider rom. After this step I am able to flash a rom of my choice again. regards
"Error, Unknown version! You should pick safe SSPL" is the error that i get when I try the Autodetect. Should I try using safe SSPL or ... ?
I also forgot to mention that I'm using Windows Vista. I heard that there were some problems updating ROMs using the Windows Mobile Device Center, so perhaps this is the problem ?
To start with I strongly recomend you read the WIKI.
As first base you should install HARD SPL (again read the WIKI).
After you'll have hard spl on yor TyTN you should use autodetect.
(Make sure you are fully connected in Windows Mobile Device Center befor any of the above)
I've installed HardSPL guided by http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
but I still get the same error. I also changed the WMDC drivers with those from AS again beign guided from the above link. Should I tick the SPL-2.02/2.10/2.30 New Bootloader or what should I do ?
Flash using an SD card.
YES pick Safe SSPL, it will run through and be fine. Sometimes that happens.
Flash a stock WM5 ROM. Get into windows. Download HARD-SPL (2.10). Use the force SPPL option while activesynced (GUEST) to flash the BOOTLOADER. Get back into windows, and use the same procedure for the OS ROM. Use force SSPL while activecyned..
I have Orange branded spv m700 and have unlocked and supercid'd the device using pof's tool. I then added HardSpl (Olipro 1.20). All appear to have loaded fine - phone is unlocked and Olipro shows up when put into bootloader.
So, the problem - every time I flash a cooked ROM (Ausdim, NiAx, FiNixNover...?) it won't boot past the first screen. I can rescue the situation by putting device into bootloader and flashing the official WM6 ROM (no radio, no ipl....) and it boots up just fine.
Can anybody help or at least point me in the direction of some good advice?
hmm... odd... can you list step by step what your procedure is for flashing the ROMs
I've done lots of devices - old XDA2i, SPVM600, wifes SPV M700 (unlocked, hard spl etc and flashed away!
This particular device shows IPL 0.50 & SPL 1.20 Olipro. It is unlocked (have o2 sim working in it), and should be SuperCid (I checked the box and radio shows as 1.16.00.00 - pof's patch I believe?). I also re-run HardSpl and Pof's unlock/supercid patch just in case it hadn't flashed properly.
I generally just download ROM and flash via RUU. Occasionally I get the device not responding error so I just re-run RUU from the bootloader screen.
Have tried WM 6.1 and 6.0 cooked roms but all show initial boot screen (numbers along bottom) next screen and then frozen, have waited and waited and nothing. Also, it would not flash back to Mozzers WM5 Orange UK ROM - same symptoms. I thought it was bricked, but the Dopod WM6 flashed perfectly.
Hope that helps - thanks for looking into my problem.
anybody please? por favor........
hmm.. i remember someone having a similar problem but it was some time ago..
two things to try just in case...
1) i'd manually go to bootloader (hard-spl) before flashing
2) Have you tried to flash from SD card? this method seems to provide less problems..
let me know how it goes..
A degree of success - managed to flash WM6 AX3L. All seems to be working. As I recall this is very similar to the official ROM and I used to use it last year because it is very stable. Think I moved on because of the missing email accounts problem. Will happily keep it if I can sort the email problem out. Never really had much fun with the hard reset after loading method - is there another/better way? Just wondering.
Also, now I have a "cooked" rom loaded perhaps it will stop being so sensitive.....!!
How strange! Have just flashed Akeo's new Diamond port ROM and no problems. Not only that, the ROM is FAB!!!
So as you can figure out from the thread title I have a problem flashing my htc diamond.
I have installed a HardSPL version 1.30 OliNex, I can confirm that becouse on the three color screen there is a text saying "1.30 OliNex".
I still have the original ROM that comes with the phone when I bought it, so this meant to be my first flashing.
I want to flash the phone with this rom http://forum.xda-developers.com/showthread.php?t=593678 it is a WM 6.5 based ROM.
Because in the ROM package there wasn't a ROMUpdateUtility.exe I used it from other ROM package.
Connected via ActiveSync and followed the wizard. The phone reset and there came a gray screen with a progress bar. Now both progress bars on the phone and on the PC screen remain 0% and after a wile RUU finished with 262 ERROR Connection error, see the attached picture.
After that I tried to flash it from Internal Storage. A followed the steps according the procedure, and after the three colored screen it came the gray screen with "Loading..." message. I waited for almost 30 minutes and nothing happened.
What seems to be the problem?
I assumed about firewall disabling the connection. But I turned off the firewall and again the same story.
Then somewhere I found that there is incompatibility with the RUU and HardSPL version, but tried to flash with the same RUU that I used when I was installing HardSPL.
Then I tough that the problem is about flashing unsigned ROM on a signed HSPL, but it is not that the ROM is signed.
I am afraid to use MTTY so I don't brick my phone, because this is my first time flashing a Diamond.
I'm confused What seems to be the problem?
Any help can be welcomed.
Could this be indication of a hardware problem? When waiting for the "Loading..." message disappear the back cover warms a little.
Thanks.
1. Did you use the RUU from my thread?
2. NEVER USE AN H-SPL RUU TO FLASH ANYTHING OTHER THAN H-SPL!
3. is this a CMDA phone. IE, what network are you on?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
EDIT: I did tried the RUU you recommended in your thread but it's the same.
I think it is in the PDA.
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Hmmm..
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
johnyboy_ said:
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Click to expand...
Click to collapse
The connection between PC and PDA is made, because as I said there is a progress bar on the phone screen too.
djfuego said:
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
Click to expand...
Click to collapse
As I understand you, you are saying to install later version of Hard SPL right?
So to install a new version of Hard SPL I just need to do the same procedure as the first time, or I have to uninstall the previous one?
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
djandreski said:
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
Click to expand...
Click to collapse
Presuming from your post, you are using a signed Olinex SPL, i doubt that the rom has been signed be OliNex, the only difference with Dev is you can flash any Rom, flash the Dev one from my thread, nothing to be afraid of
Good Luck
Badwolve1
What are the steps of installing new SPL?
Do I just need to do the same procedure as the first time, or I have to uninstall the previous one(somehow)?
UPDATE: I did it, I successfully flashed my Diamond PDA! It seams that the problem was in the SPL I installed 1.40 OliNex Unsigned and it flashed like a charm. Thanks guys for the help. Now this thread can be closed, or do I have to close it myself.
Great!
Glad it all worked out