Related
HI all! It will be more then great if anybody can help me.
The story is simple one guy decide to unlock his Diamond throw some free way ( I don't know how exectly ) he end with error 260 and DEAD Diamond.
The device does not get into bootloader when pressing Vol_- + reset.
Now this Diamond in my hands.
Can anyone please advice what can I do? can I flash ROM?
P.S. this phone are new and Orange UK branded.
Please help and sorry for my poor English.
something? PLEASE!
You mention you can not get into boot loader by pressing
Vol_- + reset.
Click to expand...
Click to collapse
On the Diamond you can access bootloader by jsut reseting and holding down the "Vol Down" Key only...
Try this and report back.
Where is this error 260 indicated ? If the ROM starts up and shows some error, the bootloader will work for sure.
Cya,
Viper BJK
try to make an hard reset by press vol down + central button + reset.
maybe you have to use mtty but I can't help you cause I never use it...
R3PUBL1K said:
You mention you can not get into boot loader by pressing
On the Diamond you can access bootloader by jsut reseting and holding down the "Vol Down" Key only...
Try this and report back.
Click to expand...
Click to collapse
That what I told volume down + reset not working with this phone. It is in another one which I have here.
The phone doesn't show any signs of life, I think I need test point or maybe JTAG way to repair it......
Any suggestions?
viperbjk said:
Where is this error 260 indicated ? If the ROM starts up and shows some error, the bootloader will work for sure.
Cya,
Viper BJK
Click to expand...
Click to collapse
I don't know I got this phone it this condition with a story about this error.
I don't actually know what happened, but I believe that this phone bricked down in the middle of unlocking process.
Zoosman said:
The phone doesn't show any signs of life, I think I need test point or maybe JTAG way to repair it......
Any suggestions?
Click to expand...
Click to collapse
If there is no life in the phone then there is not much we offer/say to help.
Have you tried another battery?
omar 1958 said:
...
2. with a fully charged battery, reset your device (hard reset) press Volume down + centre round button + soft reset(behind battery cover) all at the same time, release soft reset but keep holding volume down + centre button. You should now have a white screen advising you what to do to complete the hard reset.
Click to expand...
Click to collapse
Only to make a bit easy this step cause in this way one would be an octopus , soft reset your device with stylus and then, within 3 seconds, hold Vol down + centre round button until you see the tricolour screen. Release the buttons and follow the instructions (Press Vol Up to restore to manufactured settings).
This is the typical case when someone didnt do his homework. Im sure you didnt read the stickies. Poeple be warned, flashing your device can kill it if you dont have a clue on what you are doing. Ive seen a bunch of n00bs bricking their devices just because the didnt read the forum. This question has been ansewred a lot.
Zoosman said:
HI all! It will be more then great if anybody can help me.
The story is simple one guy decide to unlock his Diamond throw some free way ( I don't know how exectly ) he end with error 260 and DEAD Diamond.
The device does not get into bootloader when pressing Vol_- + reset.
Now this Diamond in my hands.
Can anyone please advice what can I do? can I flash ROM?
P.S. this phone are new and Orange UK branded.
Please help and sorry for my poor English.
Click to expand...
Click to collapse
HI all! It will be more then great if anybody can help me.
The story is simple one guy decide to unlock his Diamond throw some free way ( I don't know how exectly ) he end with error 260 and DEAD Diamond.
The device does not get into bootloader when pressing Vol_- + reset.
Now this Diamond in my hands.
Can anyone please advice what can I do? can I flash ROM?
P.S. this phone are new and Orange UK branded.
Please help and sorry for my poor English.
sorry friend to hear but i have one solution may be it can work u just flash hard spl v 1.93 olinex from here:http://ficca.bounceme.net/download/HARDSpl_Diamond_OliNex_1.93_Unsigned.zip just flash this hspl and after flashing this u can flash any rom but now u just flash this hspl if u got 100% then ur prob is solve so pls tell me what happen after that hope every thing will be alright good luck
Error 260 is a USB communication error. Did this happen during sim unlock or during hardspl install because the thread title says one thing and your post says another.
Zoosman said:
HI all! It will be more then great if anybody can help me.
The story is simple one guy decide to unlock his Diamond throw some free way ( I don't know how exectly ) he end with error 260 and DEAD Diamond.
The device does not get into bootloader when pressing Vol_- + reset.
Now this Diamond in my hands.
Can anyone please advice what can I do? can I flash ROM?
P.S. this phone are new and Orange UK branded.
Please help and sorry for my poor English.
Click to expand...
Click to collapse
R3PUBL1K said:
If there is no life in the phone then there is not much we offer/say to help.
Have you tried another battery?
Click to expand...
Click to collapse
I have the same problem.. i tried a flash and then it wont turn on.. not even hard reset not even soft reset.. it wont even charge or indicate charging.
charly_mx said:
This is the typical case when someone didnt do his homework. Im sure you didnt read the stickies. Poeple be warned, flashing your device can kill it if you dont have a clue on what you are doing. Ive seen a bunch of n00bs bricking their devices just because the didnt read the forum. This question has been ansewred a lot.
Click to expand...
Click to collapse
Hey charly, i flashed my phones many times, i've bricked it , got stuck on the tricolour screen.... but this time it's different... the phone it's completely dead... no light .. not charging no tricolour .. nothing:S
try this method for ur diamond
first remove ur battery form ur device and press the power button for 20 seconds . so it will discharge the power from ur device. after that put ur battery and press volume - and power on button to enter boot loader ... dont press reset button to enter bootloader ok !! hope this works for u , best of luck.
noluck
rahmaneee said:
first remove ur battery form ur device and press the power button for 20 seconds . so it will discharge the power from ur device. after that put ur battery and press volume - and power on button to enter boot loader ... dont press reset button to enter bootloader ok !! hope this works for u , best of luck.
Click to expand...
Click to collapse
no luck.... i did the battery on the fridge processs.. no luck with that either... now i'm gonna check the battery with somekind of instrument and after that i'm gonna open my diamond to little pieces and put it back together... in quest for a fix
constantine_mk said:
no luck.... i did the battery on the fridge processs.. no luck with that either... now i'm gonna check the battery with somekind of instrument and after that i'm gonna open my diamond to little pieces and put it back together... in quest for a fix
Click to expand...
Click to collapse
... Because THAT will fix it
hahahha, no no no... the PDA fary will..
dieselboy said:
... Because THAT will fix it
Click to expand...
Click to collapse
hahahha, no no no... the PDA fary will..
a did some measurements, the battery was 2.8V, i put it on the phone, put the phone in ccharger, and it did charge the batery to 3.7V(even the baterry led is not working).. i measured the phone also it gives 4.15V to the battery... i dont know is he charging correctly.. but it's charging the battery for sure.. ..... any clues ppl?
Hi
I had hardspl olinex 1.40/1.24 and it got flashed properly with 3 roms, now i changed the rom again through the phone, hold voldown + back key to run the flash file, but it stopped at 60/65% and nothing happened for 10mins, so i pressed the red reset button to reset the phone, and i get the message on bootloader screen saying PSOC-Diam STAGE_PVT v0x30 Upgrade ROM code error Please try again (in the green bar).
anyone knows how to fix this problem?
i did the hard reset but still no luck
did i brick the phone?
anyone had this problem before or got a solution?
thanx in advance.
if you're stuck in the bootloader... then the only way out is flash via Custom RUU... do this... press the rest and vol down + power... without being connected to the computer... you'll see the bootloader appear... plug in the usb to your computer... and then run the Custom Ruu to flash a rom... should do the trick!
i think, you are the second person with this rom and this fault/mistake.
and as resolve i read the same anwer but with not so much points between the words ....
thanks, sorted!
Sorry for pulling this thread back to life.. but even i am getting the same error
I also went to the service center guys but they said its normal and not an issue
abhishek.vij said:
Sorry for pulling this thread back to life.. but even i am getting the same error
I also went to the service center guys but they said its normal and not an issue
Click to expand...
Click to collapse
harrysaab said:
Hi
I had hardspl olinex 1.40/1.24 and it got flashed properly with 3 roms, now i changed the rom again through the phone, hold voldown + back key to run the flash file, but it stopped at 60/65% and nothing happened for 10mins, so i pressed the red reset button to reset the phone, and i get the message on bootloader screen saying PSOC-Diam STAGE_PVT v0x30 Upgrade ROM code error Please try again (in the green bar).
anyone knows how to fix this problem?
i did the hard reset but still no luck
did i brick the phone?
anyone had this problem before or got a solution?
thanx in advance.
Click to expand...
Click to collapse
install the original rom 1.93 and after you try again to install step 1 of unlock (the hard spl)
Hi!
I just can't get into the download-mode.. i tried it hundred times! Its always just booting like normal!
I want to flash the I9000XWJM5 Firmware and then the SamSet V1.9. But i just cant get the download-mode working! So i can't flash anything...
Is there an other way to get into that mode? Or is it possible to flash the I9000XWJM5 ROM in the recovery mode?
Thanks for your help! =)
adb reboot download not working?
now my Galaxy stucks at the black/white Samsung writing! None of the button-combinations work! And it is not recognized by my PC!
What can I do now? Did I brick my phone?!?!
now my Galaxy stucks at the black/white Samsung writing! None of the button-combinations work! And it is not recognized by my PC!
What can I do now? Did I brick my phone?!?
Remove battery for 30 sec, press volume down + menu + power for more than 6 seconds (till the screen comes up). Should work than.
What provider are you on? Cos some phones from Bell dont go into download mode from what I heard.
i'm afraid so
if you can not do the 3 button combination to get it back into the download mode, you'll have to return it to samsung which will refer you back to the phone company to have it fixed
nothing helped... this sucks! those kutton-combinations did not work at all.. even before i obviously bricked my phone.. dammit!
Anyone got an other idea?
at this point there is no much to do but throw in the tower, and take it back to the place where you bough it.
tell them the 3 button restore mode doesn't work, and you can't continue upgrading to version 2.2
I had the same issue
http://forum.xda-developers.com/showthread.php?t=748475
AllGamer said:
at this point there is no much to do but throw in the tower, and take it back to the place where you bough it.
tell them the 3 button restore mode doesn't work, and you can't continue upgrading to version 2.2
Click to expand...
Click to collapse
is this update "legal" in europe? or do i lose my warranty?
hi, just a quick question. I just went to download mode, to see if i could. What do i need to do to get out of it?
It says do not turn off target!!!
Thanks in advance
EDIT: I just turned if off. Still scared my beautiful phone will break!!!
Hi guys.
I opened my bootloader. And tried 3-4 roms. They were working nice. Then i wanted to install another rom. Its DooMLoRd-Jeak rom.
I done all right. And it said its okey. I looked on my phone. Its power off. I pressed to my power button but it vibrates for 1 time. I tried to charging but not matters. There is NOT led. If I press volume up+ power + camera button it vibrates for 3 times.
How can i repair it, can someone help me?
I should do it today.. waiting for you. thanks for everyone.
I want to do it with flashboot . But i couldn't understand. thanks again..
It's woke up guys. Thanks
utkuyilmaz1903 said:
It's woke up guys. Thanks
Click to expand...
Click to collapse
hey could u share us how u save it ?
Is your phone able to go to Flashmode or Fastboot mode?? If so, try flashing the original .ftf and see.. Here's the link..
http://forum.xda-developers.com/showthread.php?t=2417672
This link has the firmware link as well as rooting method.. Do read clearly.. If u don't know how to use flashtool, use google.. U can always google for finding out the solutions for these kind of problems..
Hi Please help!!
last night it seems that my phone pushed an ota update. my phone is in fastboot mode. i cant get out of it.
I have tried rebooting. i have tried the command fastboot reboot, and it just boot into fastboot mode again. i tried to follow this androidforums. com/optimus-v-all-things-root/598014-guide-how-get-out-fastboot.html to get out of it, but no luck. but then it ended up in download mode, witch i cant get into normaly by holding the power up an blig it in.
im hoping to flash stock softweare, but my pc cant recon my phone. i have tried to install dthe drivers and reboot alot of times, but no luck
please help, realy would hate to loose my lg g3!!
sorry for poor english
Im a newb and are real dumb when it comes to this, so please describe any solution like you would describe it to an idiot. Thanks
screenshots
here are my pgone screenshot: docs.google.com/file/d/0B8hqJbFhI7LgTi1zMnZzTG81eEk/edit?usp=docslist_api
Cant find my phone in ports so cant change the port to com41 so i can flash stock
docs.google.com/file/d/0B8hqJbFhI7LgTHRNdGFqdFQ1U3c/edit?usp=docslist_api
Is there a way to freeze the oat update?
I cant get into phone so i dont know
U have to hard reset it
Sorry
GT-p5100 xda pro
thank if you like it
Im not able to. No buttons work when i turn it on. Will nont access download mode or do a hard reset. Hard reset is holding vil down and powerbutton to the lg logo appare then release and press again?
Do what you was doing but when the screen stop release your hand fast and do it again before it start
Hard luck dude
GT-p5100 xda pro
thank if you like it
It actually worked coming into the reset screen. But after boot i just ended upp back into fastboot mode
Try to flash a firmware
GT-p5100 xda pro
thank if you like it
Don know how whenni cant get it into download mode
Indelivered it back to manufacturer and the had to change the main card and also installbthe software. Did not find out about root