Related
Hi,
My Universal fail to power on.
It do not enter boot loader with light + power + reset and show no signs of life. Batteries are both new and tested in other working units.
When connected to USB, PC reports "USB device not recognised"
I had ROMS flashed but failed at 99%. When reset the units did not power on or showed any signs of life.
It had been working fine up until the unsucssesful flash update.
I would like to be able to use it for work .
Please either post replies here or email me [email protected]
Your time and efforts will be greatly appreciated.
Regards,
quou
quou2006 said:
Hi,
My Universal fail to power on.
It do not enter boot loader with light + power + reset and show no signs of life. Batteries are both new and tested in other working units.
When connected to USB, PC reports "USB device not recognised"
I had ROMS flashed but failed at 99%. When reset the units did not power on or showed any signs of life.
It had been working fine up until the unsucssesful flash update.
I would like to be able to use it for work .
Please either post replies here or email me [email protected]
Your time and efforts will be greatly appreciated.
Regards,
quou
Click to expand...
Click to collapse
Please try to enter the bootloader mode in a bright room as it is very difficult to see in poorly lit environment. Till you enter the bootloader mode your device will not be recognised. Perhaps one of the three keys is getting released..the light button is the usual culprit. Once you are in the bootloader you can reflash.
Thank d_ranade for your answer.
I am sure the screen is 'all black' and I've tried to press the buttons several times.
I think the main problem now is how to enter the Bootloader.
I sometimes find it takes several goes to get into Bootloader mode. If not, have you tried a hard reset?
I've tried whatever i can do. Hard reset is useless too.
quou2006 said:
Hi,
My Universal fail to power on.
It do not enter boot loader with light + power + reset and show no signs of life. Batteries are both new and tested in other working units.
When connected to USB, PC reports "USB device not recognised"
I had ROMS flashed but failed at 99%. When reset the units did not power on or showed any signs of life.
It had been working fine up until the unsucssesful flash update.
I would like to be able to use it for work .
Please either post replies here or email me [email protected]
Your time and efforts will be greatly appreciated.
Regards,
quou
Click to expand...
Click to collapse
I have sent you a pm, it should help you.
-Jwrightmcps
Thank Jwrightmcps for your help, but i can not enter the Bootloader ,so can not use mtty to do more.
Unable to start/see bootloader
I seem to have the same problem with my upgraded universal which was working fine for about ten days. Then I installed TomTom on it and again it was all working that evening.
Then, when I turned it on the screen went blank (white), so I re-flashed it, but, part way through the screen went black, so I left it connected for further hour and nothing. I have since been unable to get it to do anything, it is not recognised by activesynch, it will not charge (either from the mains or the USB on either of the batteries) nor will it turn on or respond in any way.
I have unset ‘allow usb connections’. I have tried solidly for +/-10 minutes doing the backlight + on/off button and reset bit - repeatedly, with my wife helping to ensure all buttons were being pressed. All I got was a message from MicroSoft telling me that ‘One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it’. The only positive thing is that every time I do it and depress the reset, the red LED flashes (provided I leave the USB cable in) but at no point have either of us been able to see any writing on the screen.
Any guidance (apart from where to take it for recycling) would be welcome…
It happened to me several times too. Even in the old ROMS. But had learned many things out of it. I removed the battery. Wait for several seconds or maybe minute before placing it back. And after placing it back wait again for some time before doing the "power + light + reset" (bootloader). At some point when I am in the bootloader mode already and reflashing, connected to the PC already, the screen went blank again. So I'm sure that something went wrong again. I repeated the procedure again (removing battery, placing it back etc...) and the reflashing continued. It takes patience (maybe).
After having experienced this so many times, I'm beginning to assume that it is not because the battery is "bad" or there is a problem on the ROM being reflashed. It is on how it (the battery) is connected to the unit. The reason why it does not turn on, charge even if connected to the charger, does not hard reset, does not react to anything... I just don't know.
One thing more, the procedure I said above sometimes does not work at once. But at least I managed to "resurrect" my device several times.
This I am sure, it is not in the ROM that is being flashed or the update...
Hope this helps,
Lelen
lelen, Thanks for your assistance. I tried last night, but it still could not enter the bootloader mode...
I have the same problem =( and i don't know what to do, someone told me that i have to change motherbord to resolve this problem, i hope there are some other solutions.
Dead Uni
I too had this problem. With the device not responding at all and not able to enter bootloader stops mtty from working.
Only way i could get it to work was to take it to an O2 shop to send it away for repair (luckily the O2 XDA range has a 2 year warranty and because its completely dead they cant tell the OS has been modified).
Unfortunatly like the previous post i think it can only be fixed by replacing the mainboard.
Hi all, i found this thread http://forum.xda-developers.com/showthread.php?t=291097&page=6
so many people have the same problem , and nobody found a solution? i can't believe that on all this universals died motherboard, and there is no way to fix it with some special cable or some programm.
yes,i post the last reply of the thread you mentioned above, but nobody can resolve it.
I recommend you remove the battery and leave it over night. Put the battery back on, ensure it is properly mouted and try booting it.
It worked for some, no idea why though. I'm actually suspecting a bad battery mounting, which results in the motherboard unable to detect a battery is iserted, thus refusing to boot.
finally managed to get mine fixed, mine was out of warranty too and sent it off to carphone warehouse express service, took 3 weeks but was fixed with a standard chargeable repair charge of £40
I have a somewhat similar problem but not from upgrading. I accidentally dropped the device after a successful upgrade and the screen got damaged. Someone picked it up, opened it and noticed it was on even though the screen was damaged, and then closed it back. By the time I got it back it was dead and could not come on again. I have since replaced the damaged screen, but the device will not come on and cannot enter bootloader either. The device get warm if the battery is left on.
coolbeans252 said:
finally managed to get mine fixed, mine was out of warranty too and sent it off to carphone warehouse express service, took 3 weeks but was fixed with a standard chargeable repair charge of £40
Click to expand...
Click to collapse
i guess thats what i will have to end up doing
anyone goten repairs done in north america?
( i live in western canada)
got the same problem
sofene said:
I have a somewhat similar problem but not from upgrading. I accidentally dropped the device after a successful upgrade and the screen got damaged. Someone picked it up, opened it and noticed it was on even though the screen was damaged, and then closed it back. By the time I got it back it was dead and could not come on again. I have since replaced the damaged screen, but the device will not come on and cannot enter bootloader either. The device get warm if the battery is left on.
Click to expand...
Click to collapse
hi..please let me know if your device is fixed and how you managed to fix it. my email id is [email protected]
http://forum.xda-developers.com/show...6&postcount=52
Hey All,
I'm currently on the CM11 04/22 nightly, and have made it all the way up to the 04/27 nightly to try and resolve this issue and have not been able to. Basically - the sudden death issue has been hitting me very hard - I can't use my phone at all.
I understand the 04/11 nightly is stable and doesn't have this issue, howevery CyanogenMod does not have this on their website.
Does anyone have this install available? (CM-11-Nightly-20140411-D2LTE.zip)
Thanks so much in advance
SLiK
please explain what you mean by sudden death? thanks
rkant18 said:
please explain what you mean by sudden death? thanks
Click to expand...
Click to collapse
I'll be using the phone (say checking my Instagram or reading a book on Play Books) and the screen may be on for about 5-6 minutes. The phone will suddenly shut off on its own. I'll start it up and then shut down again when the phone is loading. It will also sometimes say it has 1-2% battery when it really has 45% (which is what it shows when I plug the phone in).
Hope this clears it up.
SLiK786 said:
I'll be using the phone (say checking my Instagram or reading a book on Play Books) and the screen may be on for about 5-6 minutes. The phone will suddenly shut off on its own. I'll start it up and then shut down again when the phone is loading. It will also sometimes say it has 1-2% battery when it really has 45% (which is what it shows when I plug the phone in).
Hope this clears it up.
Click to expand...
Click to collapse
I had the same issue a week back. Was the most frustrating thing ever...
I finally narrowed it down to the power button. It actually had to do with the power button switch which is soldered to the motherboard. The power button was super sensative, therefore being engagded at all times, causing the phone to hard shutdown every time I tried to turn the phone on.
How I fixed it:
1. Opened my phone up
2. Broke the switch off
3. Done
Now I use my phone without a functioning power button but it was a quick and free fix so it doesnt bother me.
If I decide to do so in the future, I can also solder a new switch back and get the power button working again.
DO NOTE: This might now be the issue you may be facing, so do your research
Finally, I watched this YT video which showed me how to break the power button switch and eventually fix my phone: https://www.youtube.com/watch?v=3Glllc7bEJs
Good Luck
imcol said:
I had the same issue a week back. Was the most frustrating thing ever...
I finally narrowed it down to the power button. It actually had to do with the power button switch which is soldered to the motherboard. The power button was super sensative, therefore being engagded at all times, causing the phone to hard shutdown every time I tried to turn the phone on.
How I fixed it:
1. Opened my phone up
2. Broke the switch off
3. Done
Now I use my phone without a functioning power button but it was a quick and free fix so it doesnt bother me.
If I decide to do so in the future, I can also solder a new switch back and get the power button working again.
DO NOTE: This might now be the issue you may be facing, so do your research
Finally, I watched this YT video which showed me how to break the power button switch and eventually fix my phone:
Good Luck
Click to expand...
Click to collapse
I'm fairly confident that this isn't the power switch. And if it were I'm not sure how comfortable I would feel breaking the power switch off.
The thing that begs me to think this is a software issue is that I'll have 45% battery, the phone will die, and then I'll try to turn the phone on again only for it to tell me I have 1% battery left. I'll put the phone on charge (after it dies again) and it will say charging - 45%.
Anyway I've rolled back a few updates and it seems to be fairly usable now...
Try cleaning the USB port real well and don't use a cheap cable. Use a needle and make sure there is no lint packed in there. These things can cause the phone to cycle itself even when not plugged in. I've fixed several doing exactly what you describe.
I am new user at XDA and don't know how to place a question but I'll try my best to do it here.
I've Galaxy nexus with a weak battery. Before it went to a "comma" mode, I was able to access and use the phone while connecting it to a power source. Batter backup was like around 2 mins, or when a call comes, it pools down battery. One day I changed my phone to other phone just to go for a tour I was meant to go. After I came back and connected my nexus again, it didn't responded back. Charging batter using regular charger or external chargers, nothing worked out.
Checked online for a help to see if there is any solution, tried connecting the phone to PC while batter is out and then inserting battery again, or connecting in interval of 3 seconds for a luck. Nither option worked out.
Someone told me to log my issue here, and I hope I'll get some solution to it.
Here is current status:
It is still dead, not responding to restart or even hard restart (pressing power and volume up and down keys)
When I connect to PC the sound comes to confirm that something is connected to the laptop but it doesn't appear in device manager.
It seems like it's not completely dead, but not able to get it back.
Please help me out!
So hello community !
I have an OPPO Find 7 device, and I love, but happens that I have some problem with it, let me explain it best I can
It turns out that I simply cant Power ON the device, no matter what I try, no matter what combinations of key I am using or so. Let me explain better.
As I was using one day my phone standard it happened the lock/power key doesn't respond every time I press it, and it was so, sometimes the phone reacted to the button some times didn't. One day I had the device, and forgot to charge it, and it went completely off, so I can't even boot it up. Went to an mobile center, where they repair mobiles or so, it is small place, I explained them what is the problem, they told me it is the button power supply or so, and fixed it. That was nice, finally I had my OPPO again. After 2 or 3 weeks, again the same problem with the button didn't responded and I again took it with me and gave it to the person that fixed it the first time. They said the it is kinda complicated or so, I took it to other place to see if they could fixed it, they told me it is the POWER SUPPLY to the POWER/LOCK key. It is a waste this phone to throw it in garbage because one maybe small problem if you ask me .
Hopefully someone will see this and reply to me, I still have the phone just cant power it on.
P.S The battery is fine, the charger is fine, tried every combinations of key (just the power key doesn't seem to reply in any way or it cant get power supply). I have some minor knowledge in phone's I can tear it down but I need help or maybe solutions from you guys. Thanks again !
Still no-one that can help me maybe somehow
Did you buy it from oppostyle?
Yes that is correct, look forward to your reply and any others who think they can help ?
VASILEVSKI said:
Yes that is correct, look forward to your reply and any others who think they can help ?
Click to expand...
Click to collapse
Hi, do you still have this issue?
Did you just upgrade your phone before this happen?
Yes I still have this issue, I didn't upgrade my phone before this issue. I don't think it is an software error tho....
Got my phone still sitting in my shale
I was facing similar problem, but in my case I cannot charge the phone, and it turn out to be software problem during upgrade.
I went to oppo service center and they re-flash with the latest ColorOS then my phone back to normal.
I thought if you just upgrade your phone, you might face same issue like what I was. Or maybe you can try to go to oppo service center?
Try this. http://community.oppo.com/en/forum.php?mod=viewthread&tid=23067
If its software related this will fix it. If it doesnt I dont know anymore.
Hi
Does your phone vibrate ?
Snorl4x said:
Hi
Does your phone vibrate ?
Click to expand...
Click to collapse
No it doesnt vibrate... The power on off button dont respond
Send back to Oppo to repair or mobile shop to repair power button. Its not difficult if its only problem on button.
Power button problem
this site helps you in fixing that issue.. try it
https://www.ifixit.com/Guide/Oppo+X9000+Power+Button+Replacement/31581
VASILEVSKI said:
So hello community !
I have an OPPO Find 7 device, and I love, but happens that I have some problem with it, let me explain it best I can
It turns out that I simply cant Power ON the device, no matter what I try, no matter what combinations of key I am using or so. Let me explain better.
As I was using one day my phone standard it happened the lock/power key doesn't respond every time I press it, and it was so, sometimes the phone reacted to the button some times didn't. One day I had the device, and forgot to charge it, and it went completely off, so I can't even boot it up. Went to an mobile center, where they repair mobiles or so, it is small place, I explained them what is the problem, they told me it is the button power supply or so, and fixed it. That was nice, finally I had my OPPO again. After 2 or 3 weeks, again the same problem with the button didn't responded and I again took it with me and gave it to the person that fixed it the first time. They said the it is kinda complicated or so, I took it to other place to see if they could fixed it, they told me it is the POWER SUPPLY to the POWER/LOCK key. It is a waste this phone to throw it in garbage because one maybe small problem if you ask me .
Hopefully someone will see this and reply to me, I still have the phone just cant power it on.
P.S The battery is fine, the charger is fine, tried every combinations of key (just the power key doesn't seem to reply in any way or it cant get power supply). I have some minor knowledge in phone's I can tear it down but I need help or maybe solutions from you guys. Thanks again !
Click to expand...
Click to collapse
Sorry, didn't realized you replied my comment already. Since you purchased your device from Oppostyle, i would suggest you to do RMA. However, the process is going to take quite a long time.
So, unluckily today i find myself here lookin' for help with my phone. I had already took a look on other brick threads, but i can't find an appropriate answer to my problem.
I'm (i was) running lineage-14.1-20170602-nightly, i had ne0zone75's TWRP 3.1.0.0-0, and that's how the brick came in a strange way; i was simply on XDA Labs app browsing the forum, when i received a call. I've answered, and when i shut off the call the phone shut off immediately after. I thought it was a reboot, but keeping pressed the power button didn't switched on the phone anymore. So i've tried to remove the battery and re insert it after some minutes, but the only thing i can get is the screen with the samsung logo that goes all black after 5 seconds. I already had other bricks due some errors of mine in the past, but this time it's really difficult.
1: I can't access recovery mode. Ow, how i wish i could.
2: I can access download mode, but after that i reach the ODIN MODE screen with the details of product binary, KNOX, ecc. the phone shuts off again.
3: If i keep the power button pressed, the phone doesn't starts. It only starts if i replug the battery in, but after some seconds it shuts off again.
4: How could a call as another mess up the whole phone?
5: I didn't installed nothing new from at least a week... yesterday an automatic update of the Play Store took place, but except that nothing has been changed. Nothing of nothing! No settings, no apps...
What could i do? Installing Kies with Samsung drivers could help me flashing a stock rom for example? Because at the moment, there isn't too much that i can do with the phone in this state... I hope this little jewel won't have to become a stone to be thrown away. Any help would be great, and really appreciated. Thanks in advance...
Things has got worse. Now my device doesn't starts at all; no vibrations, no signs of life, nothing. I've tried even to put it for 6 hours in my refrigerator, because i've read that the cold temperature could be helpful to fix some broken contacts on some component, but i'm losing hope 'bout it. I supposed that at this point is something hardware-based and not software, because it's just impossible that a call like an other one could be the cause of this hard brick... The only thing is that if connected to my PC, it is being showed as QHSUSB_LOAD. I'll try some methods that i've seen in other forums, like softwares that tries to fix this, but i think that i'll be forced to buy a new device. Neither an usb-jig could help me to force the download mode if the phone is dead in every aspect... the only thing that i still didn't understood, is if a debrick.img on my SD card (sadly i've read that a microSD class 10 with at least 16 GB is required, and i don't have one) could help somehow on a situation like this one of not. Still no one could advice me with some tip, guys
Edit - feel free to close this thread, I have another phone now