Related
hi
I Have Some Problem With my phone
my phone Cannot Detect The Batry charje
what can i do?
help me
sorry for my english
what do you mean, cannot detect battery charger? when you connect the magician to a wall socket or to usb, doesn't it charge the battery?
the batry charged but the mobile can't tell me the precent of charge!!!!
it is always 0%
There is problem with your battery. Inside your battery pack, there is electronic that "tell's your device" how much is your battery charged, what temperature is it etc... if your battery isn't charged after few hours of charge then there may be some problems with your device, but if it is charged, then it's 100% your battery that is causing problems...
i have 3 batteries total. One is not recognized and it always displays 0% but it is charging and has good life, another one returns wrong values in the indicator, it discahrges quickly but in fact it is still well charged. if i remove it and put it back it riseses back to it's true value. The last one is new but it's worse than the old batteries. It's manufactured in China and it supposed to be 1800mAh but it hardly lasts more than a day. Amperage is 181 ma constantly and temperature 26 constant. Quality sucks but i think i can replace the core with one of the other bateries since they're made in Japan and they're a lot better. Problem is that I don't know either if the core is bad or the internal chip is poorly programed so that it has high power consumption
If i load my phone over night...it load full (100%) and then the led is green...all ok...but it stop the load on this point i think....because if i look 2-3 hours late the led is green but battery is on 98-99%...
And it does not matter which rom...i see it also on the original 2.1 eclair rom...
So is there a mod to Conservation Load..? or is this only in my phone..?
sorry for bad english...with kind regards...Alex
This is a standard behavior and it's not related to the phone. It's related to the battery. It's hard-coded into the battery to behave like this. It's not good for Li-Ion batteries to be kelp at 100% constant so when they reach maximum capacity the controller cut the power so the battery does not stay at 100%. It's how laptop batteries work and it's how all Li-Ion or Li-Polymer should work.
snapilica2003 said:
This is a standard behavior and it's not related to the phone. It's related to the battery. It's hard-coded into the battery to behave like this. It's not good for Li-Ion batteries to be kelp at 100% constant so when they reach maximum capacity the controller cut the power so the battery does not stay at 100%. It's how laptop batteries work and it's how all Li-Ion or Li-Polymer should work.
Click to expand...
Click to collapse
thanks for the fast and very good answer
with kind regards..Alex
Hi!
I'm looking for an application, that quickly kills my battery if it's low, so I can do a full charge to improve battery life.
Something, that I launch, I put my phone on the desk, have a tea meanwhile, and it's drained! Something, that turns on wifi, do some downloading, browsing, video playing, or whatever, and does it automatically without supervision. Does such app exists?
I'll second this, it'd be nice to have an app do this for me and maybe even give us some interesting stats from it?
Sent from my mind using telepathy
why would you want an application to destroy your battery?
Adevem said:
why would you want an application to destroy your battery?
Click to expand...
Click to collapse
Apparently if you do a full discharge the battery life will be longer.
Soniboy84 said:
Apparently if you do a full discharge the battery life will be longer.
Click to expand...
Click to collapse
not really, you should avoid deep discharges...
Byr0x said:
not really, you should avoid deep discharges...
Click to expand...
Click to collapse
+1 If you had been reading around...you would know Lithium Ion batteries are designed to 'maximize' their efficiency within about two weeks of 'top up' charging. Cycle-charging is generally considered a less efficient method of charging. You will need to 'TopUp charge' this means charging as much and as often as possible. If your battery is at 89% for instance and you find yourself near a socket, plug your adapter in and charge it up to 100%. After a few days of doing this you will notice an improvement in the life of your battery when you are not able to charge.
Actually,,,
It is not matter of running your battery down to 0%.
It is ok to run it down till phone does to power on itself.
As you know battery is a single cell Li-Ion @ 3.7v
when it is fully charged it's peak voltage is 4.2v
By the time battery mah is drained down (galaxy s has 1500mah)
battery voltage should be around 3.2~3.4v range. this will depend on condition of the battery.
Battery should never go below 3.2v personally, 3.4v is my cut off.
If your battery voltage goes below 3.2v... it's time for a new battery as this kind of voltage will damage your battery, either it will leak or puff (battery will actually get bloated.
Phone has a voltage cut off so it will not over charge over 4.2v but if it does, it will likely start to smoke and catch fire.
I am sure anyone who is into electric Radio control knows all about these batteries.
Oh btw,,, long time storage voltage should be 3.8v
You'll be asking how do I know what voltage my battery is... I personallly don't know of any apps but GPS Status actually shows the temperature & voltage of your battery.
Soniboy84 said:
I'm looking for an application, that quickly kills my battery if it's low, so I can do a full charge to improve battery life.
Click to expand...
Click to collapse
First, take into consideration the comments above regarding deep discharge of your battery...but, to answer your question, there's an app in the market place called 'Battery Refresh' which attempts to drain your battery quicker.
Well if it's all true above than its a good sign, and thanks for the info! I'm not an expert but in the old times I remember batteries had to discharged completely, maybe even if it's just a few times. Now somebody can also tell me why my battery is discharging when it's plugged in the socket with original charger? All I do is using the internet, and has. nimbuzz and a live wallpaper on. :S
You could probably enable the GPS/BT/WIFI ( connected to a router ) and run the interactive mode on Neocore benchmark.. that should enable most of the hardware components on the phone and stress the GPU/CPU.. probably would see a 25% battery drain for every 35-40mins.
I don't know what has changed with the batteries but as far as I know...
it is good to discharge new batteries 3~4 times down until phone does not power on.
Like I have said... it's about the voltage of the battery, not whether battery has any juice left in it or not.
These batteries have a protective circuitry so that it will not charge over 4.2v,
also as for discharge it is usually down to 3v but usually with a charger/discharger units that can control mah/volts/amps. With typical usage from the phone, it'll likely be discharged down to about 3.2`3.4v. Which is very safe.
You can do whatever you feel but I personally do this to every batteries I have for phone and every batteries I use with my radio controled cars.
For my RC cars, I have about 6 batteries ranging from 1cell to 3cell LiPo packs.
Each cell is 3.7volts.
But you don't have to force discharge and hurry the process.
Just use the phone normally and let it run down to nothing... than recharge to full peak.
Than again, choice is yours.
I'm looking for the same kind of applications. It's very useful for recalibrating your battery. Wipe the battery history then do a full cycle.
Sent from my GT-I9000 using XDA App
The old saying in RC Helicopters was that the difference between discharging 50% and 100% was the difference between getting 500 uses and 5 uses.
You should certainly avoid ever fully dischaging any lithium based battery.
Older nickel batteries (Ni-cd, Ni-MH) required full dischage cycles to get rid of memory the the metals pertained, lithium-ion and lithium-ion-polymer not only do not require this; but doing so will damage them.
And yes, the older ipods came with Nimh cells and they did reccomended full discharge cycles.
Im pretty sure the idea was to try not to let the voltage get below 3.5v/cell and never below 3.3. Dead flat is 3 or 2.85 which is when the battery simply cant produce any real current. The phone should have circuitry though to not let the voltage get above 4.25 or below ~3.5.. If the low battery warning comes on, set the brightness to dim, and stop any activities (unless its a phone call, its not THAT important but if youre playing games or watching a movie...) until yo can get to a charger.
By the way this being my first post (i meant to ages ago) Ill just mention that my galaxy S came with recovery mode and download mode Enabled, i got it just last month, Virgin network, Australia.
draining the battery fully was for the older battery types, new age batteries are not recommended to be drained fully
Thanks!
One more question:
I'm using my phone as a desktop replacement, because I don't have Internet at the moment. I'm using xda, dolphin browser and listening music. It's plugged into the mains and it's not charging. It says 49%, and stuck there. Is it possible I'm using too much battery?
Sent from my GT-I9000 using XDA App
Ok, this will be my last reply.
Fully draining or not is not the issue.
In RC, most modern electronic speed controllers have a built-in battery cut-off which will cut off power once it reaches certain voltage. Because OVER-draining battery without cut off can damage/kill/ or make it unable to hold voltage.
Also, once the battery voltage reach certain point (still within safe range) you will notice the motor being powered slow down. This would also be a recommended time to stop.
Cellular phones have built in safe cut off aswell. As I have said I have measured my battery after being full drained, voltage was around 3.55v or so. Which is very normal considering voltage of the battery is 3.7v only with peak charged voltage of 4.2.
Now, Someone mentioned that fully draining your battery repeatedly will dramatically reduce battery life.
Reducing life of the battery has more to do with the amount of AMP used to charge the battery. Faster charging is usually reduce battery life dramatically.
And without hobby grade chargers, you won't be able to control this charge rate.
Slow charge is better but charging at 1C rating is the normal. But charging at 1C means regardless of batteries mah rating, battery can be charged in about 60 minutes. As we all know, our phone batteries doesn't charge from zero to full in 60minutes, right? just like most of the portable devices it takes nearly 3~4hours to fully recharge. Last 20% usually takes longer because Amp provided to charge slowly lowers. That is why.
For example, if Galaxy S battery is 1500mah, than 1C charge rate is @ 1.5amp.
If battery is 3000Mah, 1C is 3.0Amps and so on.
So like I have said over and over before, drain your battery away if you have to by choice or not. Just use it up, I will bet you your battery will last longer than you keep your phone.
U should avoid draining ur battery to 0% (witch is not possible with ur phone. When it shows 0% the charge of the battery is at 10-15%). Li-ion batteries dont have a memory effect, so it would be usless discharching it completely anyhow. Best for sgs battery is charging it before it goes under 50% that will improve the lifetime of ur battery (not how long it lasts before u have to charge but how long it lasts before u have to go and buy a new one)
How do i know? Simply cause i had to learn that a few weeks ago for the job im learning.
@xxgg: yes ur right, it wont really damage the battery if u runn it till thr phone shows its empty. But using an app to drain battery as quick as possible will, since the app forces the battery to give out more Ampere than its built to give out
Sent from my GT-I9000 using Tapatalk
So most people are familiar with the seeming "bug" that if you slap in a huge extended battery (Seido 3600mAh one comes to mind) if you are charging via USB it would only charge up to the 50-60% mark
I'm seriously thinking about getting a sprint extended battery - but does this bigger battery suffer from the same "problem"
I know this one is Lithium Polymoer instead of Li Ion... does that change anything?
All I know is that I refuse to take my battery out every 24 or 36 hours to "wall charge" it directly.
Thanks in advance for you input!
J
Mine has been charging perfectly... have had it two days, and it's been great
thanks for the quick reply -- I'll try and pick one up here in the next few days. I'm sure I can take it back if the huge back or if i had any charging issues
would be nice to go 24 hours and not have to worry about the battery at all
I have loved it... i have been able to actually use my phone.... and i even had them credit me $20 for buying the battery
You could have posted in the thread in this section, just a few posts down. But to answer your question, I have not had any issues yet. I know it drops by 3-4% a little quick (30 minutes - 1 hour) but that is the only major drop I see.
accelerus said:
So most people are familiar with the seeming "bug" that if you slap in a huge extended battery (Seido 3600mAh one comes to mind) if you are charging via USB it would only charge up to the 50-60% mark
I'm seriously thinking about getting a sprint extended battery - but does this bigger battery suffer from the same "problem"
I know this one is Lithium Polymoer instead of Li Ion... does that change anything?
All I know is that I refuse to take my battery out every 24 or 36 hours to "wall charge" it directly.
Thanks in advance for you input!
J
Click to expand...
Click to collapse
Li-Po is actually not going to change anything except that you can put more cells in the same size battery, therefore increasing the length between charges.
Most of the LI-Ion batteries used in phones are LI-po now adays anyways. The orignial evo batteries are. and most of the extended batteries are as well.
skydeaner said:
Most of the LI-Ion batteries used in phones are LI-po now adays anyways. The orignial evo batteries are. and most of the extended batteries are as well.
Click to expand...
Click to collapse
Actually, they haven't used Li-Ion batteries in most consumer electronics for several years but the name has become a generic descriptor for an entire family of cells which include LiPos.
The complete name for LiPo is lithium-ion polymer and they differ from lithium-ion cells in several ways including:
The electrolyte in a Li-Ion cell is a gel (liquid) while the electrolyte in a LiPo cell is a solid polymer.
The layers in a Li-Ion cell need to be tightly compressed so they're typically rolled and housed in a tight-fitting cylindrical case, but the layers in a LiPo cell don't require that compression which is why they can be manufactured in that handy flat form factor so easily.
The nominal working voltage of Li-Ion cells is 3.6V and it's 3.7V for LiPo cells.
LiPo cells have a higher energy density (capacity/weight) than Li-Ion cells.
LiPo cells can be charged and discharged at significantly higher rates than Li-Ion cells.
The bottom line is any small consumer electronics battery pack which is flat and square and is marked as 3.7V (or a multiple of that number for multi-cell series-wired packs) is a LiPo pack regardless of what it says on the pack or in the literature.
Pete
I have owned both batteries and I'm quite familiar with the bug OP is referring to. I can say unequivocally this battery has the same issues the 3500mah Seidio battery does. If you charge this battery, while the phone is on, to max and then unplug, you will watch your charge drop from full to in the 60s in the first hour or two. The drain then tapers off significantly at that point.
I haven't really had an opportunity to put this one through it's paces yet and it may stabilize over time. I'm thinking that this new one might provide the same amount of battery life as the Seidio 3500mah one due to this bug.
EDIT: See my post on the following page. The battery/system seems to have calibrated itself.
You mean to tell me that this battery was a waste of money for me? If so, let me know. It will go back tomorrow
Strange, I don't have this issue at all and I've had the battery for almost a week. It tends to drain quickly to 95% then level out.
Sent from my HTC Evo 4G using XDA App.
SpezXVII said:
Strange, I don't have this issue at all and I've had the battery for almost a week. It tends to drain quickly to 95% then level out.
Sent from my HTC Evo 4G using XDA App.
Click to expand...
Click to collapse
My second charge drained to about 60% just like the first. I just pulled it off the charger for the third time early this morning and I am not noticing the drain anymore. I'm thinking it must have calibrated itself.
I've been off the charger for 1 hour 50 mins and I still have 93% remaining!
This is much more like the stock battery. If it continues to act this way, this battery beats the Seidio one by a mile. It's been a couple months since I've used the EVO. Has something been changed in the CyanogenMod Supersonic kernel to support extended batteries?
Shouldn't it be draining slower than stock battery?
I ahve the Seidio battery and I have never seen the battery drop to 60 percent or anything else like what people are saying. I am on CM 6 RC1 but even with any of the other dozen ROMs I have never had an issue. If my battery dropped to 60 percent a short time after unplugging it I would have sent it back the same day.
I charged my battery from 5% to full last night via usb charge. I pulled it this morning at 7:00 and it dropped to 93% quick mainly because it was on the charger well after it had reached 100%. Since 7 am Its dropped as it should. Im currently at 71% 8 1/2 hours later. So I wouldnt say all of these batteries have the 3500 seidio issue. What rom is everyone whos having the issue running?
They may have fixed something in the kernel recently to avoid this. Look up the old threads about the 3500mah battery. The battery calibration issues were universal.
Sent from my PC36100 using XDA App
looneylu said:
Shouldn't it be draining slower than stock battery?
Click to expand...
Click to collapse
The EVO stops charging at 100% and will not charge until it drains back to about 90%. The phone will continue to show "full" until you pull the plug. It will then show the true charge level.
Sent from my PC36100 using XDA App
illogic6 said:
The EVO stops charging at 100% and will not charge until it drains back to about 90%. The phone will continue to show "full" until you pull the plug. It will then show the true charge level.
Sent from my PC36100 using XDA App
Click to expand...
Click to collapse
Thanks for clearing that up. I didn't read your previous post, I guess
So do you guys suggest to get this instead of the Seidio ?
Someone take a logcat dump and look at the battery parameters of charging/not charging and you'll know if they've fixed the issue or not.
The meter will self adjust to the 1500Mah based on voltage and you think you'll get a full charge but you won't. Slapping it into an external battery charger after "fully" charging it thru the evo will open your eyes to the issue.
Here's hoping, now there's a sprint official "OEM" class extended battery that they'll get HTC to compile in additional battery drivers other than just the 1500mah one it shipped with.
Sorry folks, if you can't charge it externally, you're not going to get the FULL capability of the battery. There are ways to tricking it into taking more. Charge it fully with phone on, unplug, power it off, charge some more, unplug power on, charge more, etc.
This will continue to add just a little bit more to help bring it up, but you'll never get it full unless you can charge externally or HTC adds devices.
You can pull the source code yourself and confirm this info. You can also confirm the issue still exists with an external charger.
So I have a zerolemon 10000 mah battery for my note 3, I just switched to cm11 and noticed the battery percentage meter was going wacky and wasn't being accurate (eg. It would jump up 10 percent after a reboot or last hours on 1 percent with heavy use) so I followed the instructions for fixing it, I let it drain completely and then I charged it to 100 percent while the phone was off, then I turned it on and charged it again until it showed full just like it said to do in the instructions, after this I went into my battery status app just out of curiosity, there I saw that the battery had 4250 mv , I am alarmed by this because the battery is only supposed to be 3.9 voltz, is my battery damaged? I always thought that the batteries have circuits in them to prevent overcharge then how come it overcharged my battery??
Sent from my SM-N900T using XDA Free mobile app
Actually battery voltage is a little bit tricky:
first of all it will show higher with no load than with load on it and higher the load, lower the voltage, full charge or not.
Secondly for example my original phone battery is rated 3.8v, but at full charge will be higher than 4 volts.
I don't remember how Li ion batteries are rated, but for example NiCd are rated at 1.2v, which would be the voltage the battery shows when under full load, under no load the voltage will be more than 1.5v and if that NiCd battery shows 1.2 v under no load it usually means it's close to being completely discharged. I don't have specs for your particular battery, but I'm sure fully charged with no load will show more than 4v.
Since the battery has protective circuit, it should still be within specs, before the damage occurs, so I don't think you should worry too much, however if you were doing this all the time, I'm sure you will shorten battery life.
Full charge for lipo is about 4.2V. So the battery is not overcharged. The batteries have a protective board on them, and the charge control on the phone won't allow overcharging either.