HI Guys,
I'm trying to update a friends Diamond (Orange branded) However i'm having a problem getting HardSPL to flash on it.
Ive tried the Update utility Freezes at 0% and then after 5 minutes the utility goes into recovery mode and flashing it from Internal Storage, just sticks on 'Loading...' nothing else happens.
Any ideas?
I've tried 1.40 and the unsigned versions of HardSPL... not sure what else to try?
Thanks for any help.
Nevermind - tried the utility from a different computer and it worked ok..
Related
I've been using Mun_rus's WM6 ROM for quite a while and seeing that PDAVIET's rom was built on a more recent WM6 ROM I decided to flash PDAVIET 2.07.06.PV.
Since then I cannot flash anything on my Trinity, the update utility starts and when the progress bar reaches around 84% half the screen on the Trinity goes funny. The progress bar on the PC reaches the 100% (while the screen on the Trinity goes blank slowly slowly) but upon restarting the device PDAVIET ROM loads up again intact as if I have just done a soft reset!
I've even tried flashing WM5 again but without any success.
Trying to flash Hard-SPL does not work either and I'm running out of ideas now :-( Anyone else has this problem please? I would love to try flashing a ROM with an original IPL SPL but cannot find one. My bootloader currently says IPL 1.5/SPL 9.99.CP.
Yes I am having a similar problem. It starts to flash then stops reboots and on my pc says image fiile corrupted. I have re downloaded and extracted the files but it happens everytime. However. My trinity when it reboots is stuck in the splash screen.
I had a similar problem, though not quite what you're describing. Try removing the Mini SD (storage card) before flashing.
Also, try entering bootloader fisrt before before flashing from PC.
Hope that helps.
i have the same problem...
i get 100% done and than it is still the old one..
Well, I have now sorted it. Go to this link read first post and download and use the unbrick.
http://forum.xda-developers.com/showthread.php?t=308691&highlight=splxploit-windows
I had to run it 3 times but it has worked and now I have flashed a new rom on it and it is working fine now
deniser said:
Well, I have now sorted it. Go to this link read first post and download and use the unbrick.
http://forum.xda-developers.com/showthread.php?t=308691&highlight=splxploit-windows
I had to run it 3 times but it has worked and now I have flashed a new rom on it and it is working fine now
Click to expand...
Click to collapse
I've run the splxploit a couple of times as well. It seems to finish the process succesfully but the problem persists :-( And mine is not stuck on splash screen, the device boots normally, it's just that whatever I flash does not work. Any more ideas please?
I tryed the all i think, read the all forum up and down, started in different ways, but no rom of SSL apply...
What is that!
I am stuck with this rom?
Any of the pro cookers can help with this please? I just need to understand what could be wrong, not necesseraly a solution
capeli said:
I had a similar problem, though not quite what you're describing. Try removing the Mini SD (storage card) before flashing.
Also, try entering bootloader fisrt before before flashing from PC.
Hope that helps.
Click to expand...
Click to collapse
Hey many thanks Removing the miniSD solved my problem I flashed at least a 100 ROMS in my life and never bothered removing the memory card before ... but there you go
hi, i had the same problem. i flashed my trinity with original htc rom and after that when i tried to flash with any other rom it gave me success message after every try but in my phone there was still the same htc rom. i used that : http://forum.xda-developers.com/showthread.php?t=293632 AND IT WORKS. FROM THE MOMENT WHEN I USED THAT FILE I FLASHED MY TRINITY 2 TIMES WITH THE SAME ROMS WHICH DIDN`T WORKED PREVIOUS. you need to copy that file to your trinity and follow the instructions from the readme file. in my case i only opened it ,it started bootloader mode ,i disconected usb and connected it again and started ROMUpdateUtility with rom which i wanted.
interesting... so why does the miniSD card affect the flash?
kta- had you tried running sspl and then flashing during your failed attempts? (just curious)
well this is my last post for the night its 2:30 and I'm tired. I'll be checking up in the morning and maybe bumping my post for more answers.
while installing oprilo's hardsplv7 my computer froze and my phone was stuck on 47% I restart my computer and reset my phone only to find it stuck in the bootloader mode spl 2.03 from the official wm6 from cingular I had on my phone. so I reinstall the cingular 3.57 software onto my phone using the install wizard. it was the only way to unbrick it. when I went to try to download most roms I get the error [240] check update utility. reading the forum it says that code is given when you have a corrupt file.
Now you know my situation here is my question, How the h*** do I totally redo my phone back down to wm5 and spl 1.04 again? or is there another way to fix my semi bricked device? I've read the unbricking page and wasn't finding anything specific to my device.
Try using SD Card flashing
or
starting with phone in bootloader mode, then hook to PC, then start update and select the correct SPL version when prompted.
Crashing while flashing SPL can be a bad thing.
I was wondering about the SD way. its wierd I can flash using sspl with pandora kitchen and it uses the bootloader 1.09, but after its done flashing the new rom and go look at the bootloader screen again its back at 2.03.
I'll try the SD way if that doesn't work, I guess I'm stuck with the highest radio using install method from cingular. although I'd really like 1.50 radio. since I have gsm network over here
Yeah, you're playing with fire whenever you flash the radio. That's where unrecoverable bricking can occur, esp. if you don't have Hard-SPL installed.
Try another PC if you can't do SD flashing... sounds like flakey USB issues to me.
best to set your phone down and don't touch it or the cable until its finished.. also make sure you have a stable machine
Hi,
after successfully flashing a lot of roms I finally landed on touch 2.1 and the gps didn't work anymore. I reinstalled factory rom and now I am unable to install anything new since with uspl there is a white screen and no usb connection afterwards. And with ruu it stops at 2-3% saying it is a corrupted file or the wrong ruu.
<br>I have the orange spv m650 and am trying everything to get a new rom on it.<br> I akso retried the two steps .bat from meschle. But that didn't work as well.
<p>Any help possible???
hi guys,
have done the Hard SpL 1.3, added radio 1.5 and tried flashing the WWE JADECore + Manila2D 1.2 PTG version successfully but however the device does not go pass the HTC screen.
i then tried to flash Mary V3.7 lite but it does not load. Requires me to do recovery. However upon recovery , it shows by hello nasty - smart mobility. Stuck right there
i flash JADECore + Manila2D 1.2 PTG again... its loading and successful, however it still reboots to hello nasty - smart mobility and stop again.
Did i miss something out? i dont understand as i assume after the Hard SPL and radio , the rest of the rom can be flashed.
i Have tried several times with this rom and mary's rom
and have soft resetted several times.
Hope for some help.
any help at all?
try official ROM first
hmm okies..
could it be that i didn't unlock the phone yet?
now its in bootloader mode.
how do i flash the unlocker or official rom in?
i still have the original wm5 disc
tried flashing the RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship original wm6.1 rom but it stops at 28% everytime i try.
the custom roms flash nicely and everything boots up until the first or 2nd page then it stops.
i'm on SPL 1.3olio and i guess the radio doesnt matter but its a 1.5
anyone could help? i'm offering a small token via paypal for anyone who can walk my trinity back to the light..
Although Olipro's Hard-SPL 1.30 is the newest version, many people have reported not being able to upgrade their device with this version running. For now it is recommended to use 1.20 or Des' crash-proof SPL for successful upgrades
Click to expand...
Click to collapse
Found at http://trinityguides.info
have used SPLxploit and it changed to SPL 3.03000
what do i do next? install HardSPL? Install CID unlocker?
boot from SD?
someone ? anyone?
I get the colored boot screen then "loading..." then the phone shuts off.
Any ideas on how to fix this?
TW,
Probably your phone is out of energy...
I feel stupid if it is... I'll slip it on the charger for an hour, thanks.
TW,
Battery was close to dead, duh!
However now it won't progress past the white screen "Loading..."
Thoughts or suggestions.
TW,
Flash from windows using custom rru
Making some progress.. Got a link to a good ruu, ATT?
Thanks,
When trying to flash via USB I get the error
"Invalid vendor ID".. then it quits and reboots.
TW,
Did you install hard spl?
Yes, it has hard spl.
Should I update it with a more recent version?
Try with 3.29
The soft SPL is 1.39... I'm getting a communication error now, could it be Windows 7?
I'll try at work in about an hour... thanks.
TW,
Did you follow this guide?
http://forum.xda-developers.com/showthread.php?t=433835
Already had a custom ROM on the phone so SPL should be there correct?
I'm getting error "262 Update Error"..
Tri-color screen shows SPL 1.93.0000
Trying to flash via SD, downloaded Cmonex's HARDSPL 3.29 SD and phone is just hanging at "Loading..."
I installed Android to NAND, will that have some impact on the restoration? Also will the verrsion of Android installed have some impact?
Finally got a ROM to load using the SD method... got the ROM from here:
http://f1ip.net/plug.php?e=index&f=./Downloads/KaiserFiles/Roms/OEMs
Thanks for all the help and suggestions..
TW,