Develop Bugs

Corrupt Charmer (PM200) upgrade help

Guys, my phone is dead and I need a little help please.
I have a T-Mobile MDA Compact II and have mistakenly (why it worked I don't know) 'updated' it with a Prophet firmware release. This progressed as I expected but was I since discovered completely wrong. My phone now shows a black screen with Dopod logo on boot and then hangs.
I have since found this site (looks good btw!) and subsequently the ftp area. I've downloaded the correct firmware for my phone, reset into the three colour screen and kicked off the Romupdater for the proper version I believe to be for my phone. With the 2 releases from ftp (one in that directory appears to be only half a zip file) they appear to be uploading but there is no change with the black screen problem.
I'm now stuck and am hunting for options. I'm more than happy to help myself but can someone explain what I need to do and start me on my way to fixing this.
All because it hangs from time to time when I run up too many apps on it.
Thanks in advance
Andy

Tell us what ROM you are using and which software you are using to perform your ROM update.
Anyway, it is weird that the Prophet ROM doesn't work on your phone. Keep this low tone, but I've done a Prophet ROM flash on my Charmer before. Everthing works well except the camera, that's why I flashed it back to the original ROM. I won't advise others to do so, there seems to be a few 'fatal' cases. I'm not sure, probably because it is compatible with the earlier Prophet version.
UPDATE: Nevermind, you seems to have the information. Good if you can stick to the same threat to avoid confusion. To others, please refer to
http://forum.xda-developers.com/showthread.php?t=275337&highlight=

At work and I've left the phone at home but I believe it was something like 2.3.15 (i.e. upgrade from v1 to v2)

Correction, it's SPL 2.15, IPL 1.12.
I have seen a post on Hermes bootloader access over USB using Mtty and now have access to the cmd> Can someone help me perform a bootloader based ROM downgrade to known working or deleting the image that is there?

Have now found the awizard utility, which file type does awizard need to be fed via the ROM directory?
Yes I'm a newbie at this and shouldn't have messed with the ROM update but I'm an I.T. guys by trade so if you can feed me the info I need I should be able to follow instructions
Phone is still 'dead' though.

It needs
XXX-OS.nba
XXX-Radio.nba
XXX-ExtROM (directory wit Ext Rom stuff)
You ought to get these from the FTP. I've myself uploaded a Charmer original UK ROM T-mobile, it should be still there is no one messed with it.

Hmm, I've missed something then. I put the .nba files into the ROM directory and then run awizard and hit w. Where I would expect to see a list of files with numbers there isn't any.
What I miss?

the dir structure of the aWizard looks like the attached, where you have the ROMs under the "ROM" dir and Ext ROM. Where the aWizard directory has the aWizard.cmd file.

Can someone provide a split up (i.e. seperated nbf files) for the Charmer or the correct memory addresses to punch into nb2nbf to create my own?
The images seem to have been removed from the FTP site and I'm in position to de-brick my phone!

O2 Cosmo (Excalibur) ROM Update - How the Hell ?

Hello Experts,
i have read a lot of the Threads here, but i can't find a good information
about my O2 Cosmo. My Dash is Simlook free and SuperCID enabeld.
I found this instructions:
Tools you need:
===============
- HexWorkshop from http://www.bpsoft.com/downloads/-
the ROM of your choice
- Winzip or Winrar
- a valid UNL file for YOUR phone
Preparation:
============
a) install HexWorkshop and Winzip or Winrar on your pc
b) in explorer on pc, RIGHT click on the ROM of your choice and use: "Extract files to folder ..." from conext menu Now it will unpack all the files
c) in the new folder you will have ONE file like "HRUU_signed.NBH" (*.NBH) RIGHT click on the .NBH file and use: "Hex Edit with Hex Workshop" from context menu
d) You'll see on the 5th row EXCA20000 ==> !!! make it EXCA***** (5 stars) and save the file
e) Now RIGHT click on ROMUpdateUtility.exe and use: "Hex Edit with Hex Workshop" from conext menu
Search for word "BsaD5SeoA" (without quotes, case sensitive)
You'll find it around address 0x3FC6C ==> !!! replace "BsaD5SeoA" with "IMEICHECK" (without quotes) and save the file
ROM-Update:
===========
1) take SIM card and SD card OUT of the phone
2) Connect the phone running windows ce to the pc (normal way).
3) Completely Unlock your phone using our unlocker <== REALLY IMPORTANT
4) After phone is unlocked run unlocker (again) BUT when the unlocker ask for UNL file, remove the USB cable from the phone THEN press "Cancel" on the unlocker select file window (unlocker will close on PC). NOTE: The screen on the device will not show something usefull when in this mode. Most probably it is complete WHITE. !!THIS IS NORMAL!! Don't touch phone, let it like it is!
5) After you closed the unlocker, attach usb cable again (phone has still white screen)
6) start (the modified) ROMUpdateUtility.exe
7) when update finished and device started you will get a message: "Data Crashed, contact service provider" (!NO PANIC!) ==> Simply fix this problem by running the unlocker again and this time select the key file normal way (full unlock process again). In case you have problems please indicate the step letter/number which is not clear/not working for you. If you REALLY do it STEP by STEP exact like described you will have no problem.
Click to expand...
Click to collapse
When i edit the .NBH file, i get a "ERROR 270" message!
When i dont edit the .NBH file, i get a "Invalid Ventor - Error Message"
I try to install this ROM:
"RUU_Excalibur_HTC_GER_1.11.407.2_4.1.13.28_02.63.90_Ship.exe"
So my Dash is a German Device, and i want a German ROM, if it is possible!?
OK, i try to go manually in the Bootloader modus, disable ActiveSync for
USB Transfer...and run the RUU Rom...but it allways break down the flash
process at 4% !
...mmh...have i forget any info, that you can help me...i dont know?
Ah Yes...i read in the Thread:
"How to flash a new ROM to your Wizard... a little tutorial!"
Here the link to:http://forum.xda-developers.com/showthread.php?t=298613
But i can see anything on the starting screen, if my dash ist a G3 or G4,
on my start screen ist "ABSOLUTLY - NO - Information" about it!
In the "System Information" i found a RIL Nr. 2.0002 ...
So i think my dash is a IPL/SPL G3...but i dont know it really!
I dont know what i can do anymore, to update my device to WM6.0 or 6.1
Plz, if anyone know what i can do, to fix my problem, plz then tell it to me,
thank you very much, and forgive me about my bad english!

Ok, i test many times this tool "Excalibur USPL- CID BYPASS" ...and yesterday
it works suddenly...i dont know "why" it works, i have done the same, like
every time i try it, but yesterday my dash move to the needed "WHITE
Screen"! And so i able to run the Rom Update, and it works fine!
Ah yes, my Phone tell me i'm in "SuperCID" Mode...so "WHY" i must use
this "CID Bypass Tool" ....crazy??? Or is my Phone a Liar...?
I have now installed this Rom, it Works a bit faster i mean:
RUU_Excalibur_HTC_GER_1.11.407.2_4.1.13.28_02.63.90_Ship.exe
But it is the same Rom Vers, like my old O2-Cosmo Rom, WM5.0 (1) with
Future Pack. But i have now the HTC Splash Screen!
So i want now to install this Rom (with WM6.1) :
"NoThrills_WM61_GER_V3.exe"
This is a "Kaiser" Rom... "Warum eigentlich Kaiser, hat der Beckenbauer damit
was zu tun...*g*
But when i try to run again the "Excalibur USPL- CID BYPASS" tool, my
dash show me only the "Linux Monkey" (Pinguin) Screen and hang up the
Phone, so that i must remove the battery....
The "White Screen" (that is the Screnn you must have to flash your Rom),
will dont come anymore....i dont know how...??? I start this batch file,
"Uspl.bat" ... and follow the instructions....mmh....allways i get the Linux
Monkey Screen...and not the white screen, "WHY" ?
Anybody a hint, how i can move into the "White Screen" Modus?
And a Question, is this Kaiser Rom compatible to my HTC S620 ?
Please belive me, i read a lot here...but i cant figure out this..., this Forum
here is a bit confusing, on many Threads you can read other informations!
Plz anyone, tell me (who know it) how i move exactly in the White Boot Screen?
Thank you!

If I understand you right you flashed a rom from the HTC Kaiser on your Dash. That's Windows Mobile 6.1 Professional for Touch Screen Devices. You need a rom from this thread for your Dash, not the Kaiser thread. Those ROM's are specifically for that phone. I doubt they'd even work on other Touch Screen phones because of it has the radio (I believe Radio is like Drivers in Windows, I may be wrong.) for that phone. As to fix your problem. I have no clue. Maybe you can get lucky and reflash it with an Official Dash ROM for your phone, but better getting advice on that from one of the more experienced people here. I'm a bit of a newby when it comes to this phone stuff. Good luck...

drkfngthdragnlrd said:
If I understand you right you flashed a rom from the HTC Kaiser on your Dash. That's Windows Mobile 6.1 Professional for Touch Screen Devices. You need a rom from this thread for your Dash, not the Kaiser thread. Those ROM's are specifically for that phone. I doubt they'd even work on other Touch Screen phones because of it has the radio (I believe Radio is like Drivers in Windows, I may be wrong.) for that phone. As to fix your problem. I have no clue. Maybe you can get lucky and reflash it with an Official Dash ROM for your phone, but better getting advice on that from one of the more experienced people here. I'm a bit of a newby when it comes to this phone stuff. Good luck...
Click to expand...
Click to collapse
Thank you!
But "NO" i don't flash my HTC S620 wit a Kaiser Rom..."What a Luck" ...i try
to do it...and now im Happy that this have not work for me!
I actually install this Rom:
RUU_Excalibur_HTC_GER_1.11.407.2_4.1.13.28_02.63.9 0_Ship.exe
I have now understand, what is a Kaiser ROM, it is the Device Name, oh
Man...i'm so a dummy....haha...
But i have a success, i change my O2 Rom to a HTC Rom
The Question now is, how i move in the "WHITE BOOT SCREEN" ?
That i'm able to Update my Rom to a WM6.1, if posible, a German 6.1 Rom.
Is here a German WM6.1 Rom?
Is a WWE a Multilingual Rom, is in such ROMs German Language included?
And how i can remove the CID forever, so that im able to update a ROM
without a CID Bypass Bootloader?
Any ideas?
The thing is, ...this CID Bypass Bootloader work "ONCE" and now that
Bootloader dont work anymore...i dont know why...i get only the Linux
Pinguin Screen...and this is a "Hang up Screen" so that i must remove
the Battery, for a new start.
But i get nevermore the "White Boot Screen" ...how is this posible?
I do the same, like before i do...mmh...???

If I understand what's been said. You need to re-run the CID-Bypass anytime you reflash you phone. As for a German ROM. I am not sure. Ypu'd need to look around through the furom. You could try the "Seach" feature and see what you come up with.

drkfngthdragnlrd said:
If I understand what's been said. You need to re-run the CID-Bypass anytime you reflash you phone. As for a German ROM. I am not sure. Ypu'd need to look around through the furom. You could try the "Seach" feature and see what you come up with.
Click to expand...
Click to collapse
Thank you,
but i try to run the "CID Bypass" but the "CID Bypass" run every time
into the "Linux Pinguin Screen" ...(i think it is programed in Linux?)
But the same "CID Bypass Bootloader" - work - for me "once" !
But now, not ! I dont know why?
With this CID Bypass Bootloader, i flash my Q2 Rom into a HTC Rom !
But that was only possible, as my dash move with this "CID Bypass Bootloader"
INTO a "White Boot Screen"...!
But "HOW" this was possible...i dont know...now this CID Bypass Bootl.,
wont work anymore....
You know what i mean?
The same tool (CID Bypass) wont work anymore, it work one time only.
When i now try to run this CID Bypass, i get a "Linux Pinguin Screen" in
Black. So there is a little Linux Pinguin "Preloader" ...and then the Phone
have a SOD..."Stand of Death" you Guys call that so, i think so!?
To search here, is very strange for me....i get results of all Forums here!
That was the reason why i want to try the Kaiser Rom, while i search
here in the Excalibur Forum...so i had think so, that was wrong, you know!?
Sorry, my english is not good enough to tell exactly my expirience!
But Thank you for Advice!

Hum, does it still look like windows mobile? If so they may have just changed the load screen. Either way when you run the bypass program, there' one step that'll show a screen on the phone when in windows mobile itself and you must press the center soft button to "continue" and then it'll enter the white screen mode. Sometimes I forget this step and bounce through the steps missing that. If you can't get into windows mobile, try reflashing with your phones official ROM first. They don't require the white screen. There's also a way to enter the bootloader screen by holding down a button, I forget which, while you press power to turn the phone on.

drkfngthdragnlrd said:
Hum, does it still look like windows mobile? If so they may have just changed the load screen. Either way when you run the bypass program, there' one step that'll show a screen on the phone when in windows mobile itself and you must press the center soft button to "continue" and then it'll enter the white screen mode. Sometimes I forget this step and bounce through the steps missing that. If you can't get into windows mobile, try reflashing with your phones official ROM first. They don't require the white screen. There's also a way to enter the bootloader screen by holding down a button, I forget which, while you press power to turn the phone on.
Click to expand...
Click to collapse
...no no, this ROM runs great! I have no Problem with this Rom!
But i have found a Solution "Yeah" !
For all who want to flash a O2 Cosmo!
Try this Link: Click
Thanks to the Uploader, found it by searching!
The last in line: "Unlock_phone_files.zip" !
Follow the steps in the text document!
Work fine for me!
But when you want to flash, and you get a connection ERROR, remove
the USB cabel, and put it back on your Dash, and run then only the
"ROMUpdateUtility.exe" again and it will work.
(Your srceen are allways WHITE!!!)
I had flash for 10min the "RUU_Excalibur_SPL-1.11_UpgradeOnly.exe"
You must extract the exe file, and copy the *.nbh file to folder 3!
After you run the "Auto.bat" and the Connection Error, click finish,
remove the USB cabel, put it back on the dash and run again and only
the "ROMUpdateUtility.exe" !
All work fine!
Thank you Developers!

HELP! Can't restore original spl 1.93 from olinex1.40

Hi there, I'm Italian I'm here because your'e the only one on this planet who can help me.....so sorry for my english.....
I had some trouble with my diamond, the touch screen is no longer working so I have to send it back to htc, now I have to restore original rom and spl.....
I installed olinex 1.40 and the last original italian rom 2.03....
Now I downloaded my former rom (1.93.772) from italian server, I installed it and everything seemed to be right, (I can't check it because the diamond blocks me at the aligning screen, the touch screen is broken and I can't start the phone...the aligning screen appears to me forever and there's no way to bypass it)...
Then I downloaded the original spl 1.93 from your server...I cant use active sync because I can't start the phone so I have to work in boot mode.....I followed carefully the procedure, that is quite easy, but there is no way to remove the olinex 1.40, the process starts, it reachs 100%, but when i check the spl is always the 1.40 olinex....and restore original spl...I try also the usb trigger mode, with the spl putted as dimndimg.nbh...
Please help me!!!!!!!!! I' going crazy!!!!!
Thank you very much for the attention...
DAVID

do you hear me?

hi
hi, did you check out this? http://forum.xda-developers.com/showpost.php?p=2324837&postcount=20 see if that helps you.

I read everithing and now I'm a sort of diamond technician, but I cannot solve this problem, I can only flash in bootloader mode cause the telephone cant initialize windows, it' blocks in the aligniment screen and can't go on, so maybe the bootloader mode isn't strong enough to by pass the write protection of the 1.40 olinex and overwrite the hardspl...HELP HELP HELP

I'got the same issue, you have to install a rom !! and use ActiveSync in order to get the SPL1.93 ! I think in bootloader mode, you can't change the SPL!
Good luck

Freaky, I have the same issue it will not remove no matter what.
HTC have sent mine back, they say the HardSPL 1.40 OliNex damages the mainboard and causes touch screen failure! They want £230 for a new one
If you find out how to remove let me know, I've flashed all sorts and no luck it still says it.
Andrew

PS) I have activesync working with a failed touch screen (stuck on the align screen window), copying and running stock 193 in /internal doesn't change it. When I try:
http://forum.xda-developers.com/show...7&postcount=20
it sits at 0% then fails. The other program they mention to force it uinto bootloader I can' run obviously because the touch screen is broke.

miscioidi said:
Hi there, I'm Italian I'm here because your'e the only one on this planet who can help me.....so sorry for my english.....
I had some trouble with my diamond, the touch screen is no longer working so I have to send it back to htc, now I have to restore original rom and spl.....
I installed olinex 1.40 and the last original italian rom 2.03....
Now I downloaded my former rom (1.93.772) from italian server, I installed it and everything seemed to be right, (I can't check it because the diamond blocks me at the aligning screen, the touch screen is broken and I can't start the phone...the aligning screen appears to me forever and there's no way to bypass it)...
Then I downloaded the original spl 1.93 from your server...I cant use active sync because I can't start the phone so I have to work in boot mode.....I followed carefully the procedure, that is quite easy, but there is no way to remove the olinex 1.40, the process starts, it reachs 100%, but when i check the spl is always the 1.40 olinex....and restore original spl...I try also the usb trigger mode, with the spl putted as dimndimg.nbh...
Please help me!!!!!!!!! I' going crazy!!!!!
Thank you very much for the attention...
DAVID
Click to expand...
Click to collapse
In order to switch from 1.40 to 1.93 HARD SPL, you must you the jump spl program. It's in my signature. Also read the txt included for the instructions.
Let me know how it goes...

band27 said:
In order to switch from 1.40 to 1.93 HARD SPL, you must you the jump spl program. It's in my signature. Also read the txt included for the instructions.
Let me know how it goes...
Click to expand...
Click to collapse
>> prun JumpSPL.exe ...
ERROR: CreateProcess failed with errorcode = 30123
- UNKNOWNERROR: 0x000075ab

snoopy20 said:
>> prun JumpSPL.exe ...
ERROR: CreateProcess failed with errorcode = 30123
- UNKNOWNERROR: 0x000075ab
Click to expand...
Click to collapse
First plug phone into computer via active sync....
Then:
Copy the following files to the Diamond root directory
"Copy JumpSPL.exe & "copy SSPL"& sspl-1.01-reloc-mod.nb
Then: "execute Diamond SPL now - screen may trun black"
Then: "run DiamondCustomRUU.exe to flash any HardSPL

What is "copy SSPL" ??

snoopy20 said:
What is "copy SSPL" ??
Click to expand...
Click to collapse
Copy means either to right click and select copy to then past it to the root of the diamond directory or you can choose to drag this file to the diamond directory. Then continue to copy the other files.
Another way is to just start with the Diamond-SSPL.exe file and it will tell u to copy these files one by one. Make sure that you are activesynced prior to started this.

What I mean is WHAT IS sspl.exe
It's not in your magic zip file.
And when I find it, how can (I / We) execute it with failed touchscreens?

Still getting ...
>> prun JumpSPL.exe ...
ERROR: CreateProcess failed with errorcode = 30123
- UNKNOWNERROR: 0x000075ab

I'm having the same problem tryng this stuff...does't work at all....I sent 2 private message to olipro but no response....Is there someone out there who can hepl me??????

is there any absurd rom using just the button of the pda excluding the touch screen??????

You must flash in bootloader mode and run ROMUpdateUtility.exe in "C:\ROM" with file "RUU_Signed.nbh" 1.93 version in his directory (C:\ROM).
Use Windows XP and cable miniUSB original and Activesync of course.
1)Use Activesync conected.
2)Copy ROMUpdateUtility.exe and RUU_Signed.nbh (HardSPL 1.93)
3)Enter in bootloader mode
4)From "C:\ROM" run ROMUpdateUtility.exe

Leoarg....I can't activesync the diamond in bootloader mode....I can activesync only if I start the diamond in normal mode....when it reaches the aligniment screen it stops and sinconize

miscioidi said:
Leoarg....I can't activesync the diamond in bootloader mode....I can activesync only if I start the diamond in normal mode....when it reaches the aligniment screen it stops and sinconize
Click to expand...
Click to collapse
mmmm, Ok. What problem!

Why remove the 1.40 is so hard?????.....why flashing in bootloader mode doesn't bypass the overwriting protection?? why olipro is not answering my private message?

HELP on installing new ROM

HI,
Im having problem installing a new ROM wm 6.5 to my touch diamond1. I tried doing the installtion from my internal storage. I renamed the new ROM already and place it in my internal storage and tried to install from there. I have a hard SPL Olinex 1.4 or 1.37.
after I pressed the lower vol+back button the red/green/blue screen cam and then a gray screen asking for movihand.mtg and after that it loads another gray screen saying loading.............. for a long time.
If anyone has encountered this problem need assistance.
Im trying to install deepshining ROM ver 8.
Thanks,

You need unsigned hard_spl like the Olinex 1.40 or 1.93
see this post:
http://forum.xda-developers.com/showthread.php?t=416211

do not forget to use the search option
things i found to check:
do you have the hardspl 1.93 (are you sure)
try deleting the files on your internal storage (or copy them to your computer) and only put the DIAMIMG.NBH file in the root
try it with the customruu.exe if it stays at 0% for too long, something is wrong, probably with your hardspl
put your device in bootloader (rgb screen), connect to computer, on the bottom serial should change to usb. try using customruu.exe.
you need to have the nbh file in the same directory as customruu offcourse.
maybe a not so nice remark. sorry in advance:
but if you have so many problems why try flashing at all? i can guarantee you that you will run into problems using custom rom's. you will have to do a lot of searching and trying to find solutions. the manuals about flashing are already in the forums. and working for everybody else. so you are probably doing something wrong.
I would suggest that you search a lot more and longer and list everything you tried. you are not the first to run into problems, and you will not be the lasts.
good luck

thanks I will try again thanks for the advise.

How to upgrade ROm with nbh file

As newbie on this, anyone please guide me step by step to upgrade my P3300 rom with nbh file. My device is unlock already with current ROM 5.2.1908 (build 18125.0.4.2).

The procedure is given in almost every thread. It's simple really. Is your SPL version anything other than 1.11.0000 or 1.11.cmon? If yes then your phone is not unlocked. Unlock your phone by running USPL from here or the updated USPL from here.
Check if the USPL has worked by checking your SPL number. During phone booting at the white HTC screen your SPL should show either 1.11.0000 ir 1.11.cmon.
If it does you are free to flash any ROM. Get the ROM of your choice, put your phone into bootloader mode by pressing the voice record, power key and reset button simultaenously for about 5 seconds till you see a three colored screen. Attach it with USB and flash the rom using RUU.

thanks randythered for ur reply. I did w/o problem on USPL but how to use the nbh extention? where that nbh file I shall put in? pc or devise or on specific folder? I got the three colors already, then what next? pl. enlighted

stacknickel said:
thanks randythered for ur reply. I did w/o problem on USPL but how to use the nbh extention? where that nbh file I shall put in? pc or devise or on specific folder? I got the three colors already, then what next? pl. enlighted
Click to expand...
Click to collapse
do u have only .nbh file or along with .nbh file any other files are there ?
generally along with the .nbh file there are other files like romupdateutuility.exe etc.,
download those files also and save those files into your PC.
after unlocking your device then staup the device with bootloader mode (three color screen)
connect the Device with the PC by USB cable.
in the device display u will a word USB (left bottom corner)
run the Romupdateutility from the PC...
the process will guide u next steps ...
after the completion u will have new OS
Last I would recommend tht u also upgrade you Radio ROM (this is responsible for all the communication functions of ur phone i.e. calls, GPS, WiFi etc) which will enhance the communication capabilities.
Radio ROMs Link : http://wiki.xda-developers.com/index..._RadioUpgrades.
Note : before flashing any ROM or upgrading the RADIO kindly CID unlock your device or you will end up the with bricked device .

You can download my ROMs, they come with the full package

trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help

stacknickel said:
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
Click to expand...
Click to collapse
your device not properly CID unlocked...
unlock the device properly with USPL...

stacknickel said:
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
Click to expand...
Click to collapse
As sixthsigma said, did you check if the phone is correctly unlocked? Is the SPL showing 1.11.0000 or 1.11.cmon?
Secondly, what OS are you flashing on? XP, Vista or Windows 7?

Hi Randythered, IPL 1.25.0001 and SPL 1.27.0000
I am using your ROM RtR Manila v1.0
using XP

Well, firstly thank you for wanting to try out my ROM
Secondly, you haven't unlocked your phone properly yet. The SPL must be 1.11.0000 or1.11.cmon, depending on which USPL you use.

strange... hv tried several time but w/o luck...
now I notice that it cut out after '70' and jump into 100 with disconnecting
any choices of other USPL instead of the one attached here?

Did you flash the old USPL or the new one which is nosize? It is preferable to install the old one first. And then go for the cmon nosize USPL if need be.

From a noob to a noob
Hi, heres the procedure for upgrading your rom put as noob friendly as i can put it.
WHAT YOU NEED
1. HTC Artemis p3300
2. computer running Windows XP with activesync installed
3. Usb cable to connect to computer
4. The new rom that you want to flash
5. And USPL which can be downloaded at this page http://forum.xda-developers.com/showthread.php?t=311403
NB: For most of the newer roms you will probably need the updated nosize version of uspl http://forum.xda-developers.com/showthread.php?t=521406
PREPARATION
NB: Anything you need to backup or keep from your device do it now.
NB: in some cases you may have to hard reset your device before it will take the flash
1. Extract Uspl to your desktop
2. Extract the rom you downloaded to your desktop
3. Remove your sim chip and memory card from your device
4. Reset your device and sync with windows xp
UPDATING
1. In the USPL folder run the program called "start_uspl" and let it do its thing in the dos window,in
my case it goes to 70 and then jumps to 100,if you have been watching your device screen you will
see the linux penguin for a few seconds and it will change to a white screen.
A window will popup on your computer, do as it requests, when finished it will reset your device.
Sync your device with your computer again.
2. In your downloaded rom folder you should find a file called "ROMUpdateUtility.exe" or "Ruu.exe", run
it and a window will popup, do as it requests.
Your device screen will go tri-color(red,green,blue) and the rom update will begin, wait till it
finishes and thats it.

thanks soloman1 and others
finally I got it with removing the sim card and memory card prior to upgrading

stacknickel said:
thanks soloman1 and others
finally I got it with removing the sim card and memory card prior to upgrading
Click to expand...
Click to collapse
same ting got me with my first rom thats why i thought to put it in, happy flashing (not in the naked way )

Lol I can't belive I forgot to tell you that!

It's ok. Thanks to u too randythered.
Do you have dedicate Manila in cab file?

Thank you, here you go!

sixthsigma said:
your device not properly CID unlocked...
unlock the device properly with USPL...
Click to expand...
Click to collapse
Sixthsigma...you said - "unlock the device properly with USPL..." - how do I do that?
I got the same error as mentioned when trying to flash using the numb3rs ROM:
http://thewingster.com/numb3rs.aspx
I ran the herald-uspl.exe file. and ended up with teh above error. My TMo Wing has the original ROM on it and the phone itself is probably unlocked. Ive had it for a year now. Do I need to call TMo to unlock or is there some app I can run to do this myself?
appreciate any help!

nevermind, it worked ok on the second attempt!