Is anyone using A2DP? Do you find volume is too low? - HTC Excalibur

Hi
I was wondering if anyone here is using A2DP for streaming music, and is having problems with the volume?
I'm using PocketTunes with a Sony Ericsson HBH-DS200 headset and I have to ramp the volume all the way to 100% in PT to get it to pump out what I think is a reasonable volume. Anything much below that isn't loud enough to drown out public transport etc, and that's using those in-ear phones that are supposed to isolate at least a bit!
I've disabled the option to limit PocketTunes volume to the system volume so the system volume setting isn't set too low or anything like that.
Weird thing is the phone speaker is nice and loud and if I plug in a wired headset then I can get a comparable volume level at around the 55-60% mark.
I'm beginning to think it might be my headset, which doesn't have a volume control on it... but I thought headsets that did have a volume control just adjusted the volume on the device which wouldn't really make any difference!
All apps seem to be limiting in this way, whether it's WMP or PocketTunes or TCPMP. There are boost options in settings but all that does is distorts my music really, which is rather distracting.
Any advice appreciated! It's hard to tell whether it's the device, the headset or the software. Running WM6.5 and have done some registry tweaking to disable joint-stereo and increase the A2DP BitPool, so the quality's fine - just too soft.
Cheers
J.

Related

Annoying background static on stereo BT headset

Hi all,
Just got me a Sony DR-BT10CX bluetooth stereo headset. I'm new to these things, so I have a bit of a newbie question. The sound is quite good, much better than the ones that came with my HTC Touch (obviously), but there's a considerable static in the background, that seems to increase when I increase volume, but only when regulated on the headset itself. If I increase volume on my Touch (in WMP, or volume slider), the static doesn't seem to increase. I was just wondering if this is normal in these headsets? This headset sells in Holland for just under E100,-, so not really expensive, but not really low end either. Could it be a faulty headset or crappy design?
All thoughts and experiences very welcome...
Thanks,
Driekus
A2DP question
Might be a silly question, but have you tried turning the volume on the Touch up to 80% and turning the headset's hardware volume setting down??
Some A2DP stereo headsets have a particular setting they work best at..
Failing that, you may simply have a headset with firmware that really isn't perfectly compatible with your PDA...
Good luck,
Andy
www.pressdigital.com.au
Support Team
As a matter of fact the volume on my touch is currently up to 100% as is the one in WMP, so that I can keep the volume setting on my headset low, but that's not really how it should work I think. Besides, incoming calls are now very low volume, so I have to adjust the volume on the headset everytime a call comes in (and quickly lower it when I hang up in order to prevent hearing loss...) and I tend to miss appointment-announcements by MS Voicecommand because of this as well.
I guess the headset isn't perfectly compatible with my Touch, as sound sometimes skips (which is even more annoying because it doesn't happen all the time) and my pda doesn't automatically connect to my headset (solved with A2DP-plugin, see http://forum.xda-developers.com/showthread.php?p=1503123#post1503123), but I'm not sure whether the background hiss is because of this too.

REQUEST - Volume Control

Ive been searching everywhere for this but either nobody has thorght about it or its not possible.
with my Touch HD the volume is far to loud to listen to music as background music or through earphones and the HTC volume control step size for the volumes is too big. its either off, medium, loud or very loud!
the default WM6.1 control is even worse!
i know that you can use your finger to adjust the HTC volume control but this still isnt sensitive enough for me.
and i also know that it is possible to adjust the volume through tweak HD or advanced config. only problem with that is that I want to be able to chose to listen to very quite music or turn it up very loud without having to go through one of those settings.
so i was wondering if anybody could make a program that either has a large step size or a user defined step size for the volume and that is activated/volume through the volume buttons.
Thanks!
P.S sorry if this is in the wrong section or if there is a requests thread but i couldnt find it.
Ok i havnt found exactly what i wanted but i did find this:
http://handheld.softpedia.com/progDownload/Volume-Control-Download-35536.html
this is an aplication which lets you choose the volume with 100 steps. and it works from the system volume so using somthing like nitrogen or media player there is another 100 steps giving me 10000 steps haha
the bad points are that you must go into filemanager and manualy start it. and even then it does not work with the volume buttons.
(if anyone knows of a way to start this when powering on the device that could be useful!)
its good but not ideal.
if anyone else can come up with somthing better speak up!
create a shortcut to the exe and add it to /device/windows/startup ?
Yep, would be nice if the volume rocker can use this little tool.
Hello,
Any news on that topic ?
Thanks
I have the same problem, i think the stepsize can be changed in the registry but i dont know where i could find this.
Just to let you know the Volume rocker switch adjusts sound in 3 steps at a time. But during music play back you can use finger or stylus to adjust volume bargarph displayed on the htc HD screen in single step and thus volume is more finely controlled. There is no need to make registry changes.
The problem is, if youre using the E100 headset (or just want to press a button in your pocket to adjust volume) it would be nice if it'd adjust 1 step instead of 3 when pressing volup or voldown..
If youre moving and just want to adjust volume its really annoying to get your phone out of your jacket/pocket, pull out your stylus and lower your volume to 1..... might be just me that is a lazybones, but still!
With Good intra headset, even one bar is too much. Is it a WM limitation that the stepsize is that big ?
khanms said:
Just to let you know the Volume rocker switch adjusts sound in 3 steps at a time. But during music play back you can use finger or stylus to adjust volume bargarph displayed on the htc HD screen in single step and thus volume is more finely controlled. There is no need to make registry changes.
Click to expand...
Click to collapse
The actual problem is that 1 bar (out of the 15 available), ie the quietest setting the system is capable of, is TOO loud. I wouldn't dare use headsets at 10 bars (out of 15), the sound level would blow my eardrums out.
What we'd like to do is change the "range" of volume output - so that the output power is a LOT lower at low settings, while remaining loud enough for public broadcast (ie from the speaker on the back) at higher settings.
Anyone?
Same issue here. The minimum volume is still way too high. It's a waste of battery and could hurt your ear if you use in-ear earbuds.
Riceburner said:
The actual problem is that 1 bar (out of the 15 available), ie the quietest setting the system is capable of, is TOO loud. I wouldn't dare use headsets at 10 bars (out of 15), the sound level would blow my eardrums out.
What we'd like to do is change the "range" of volume output - so that the output power is a LOT lower at low settings, while remaining loud enough for public broadcast (ie from the speaker on the back) at higher settings.
Anyone?
Click to expand...
Click to collapse
As an addition.... I think this "too much volume" thing is something to do with the HTC TF3D music player itself.
On my (stock Rom) HD - I can listen to the FM radio at "normal" volume levels (ie about halfway up the range), but with the TF3D player - I have to turn it right down again.
Haven't tested it with other players (eg TCPMP).
Another request for a better solution to volume control.
bumpity
I have the same problem, ever since getting a set of in-ear MM50 (Sennheiser).
Too loud!
Any ideas?
gromitt said:
Another request for a better solution to volume control.
Click to expand...
Click to collapse
You may edit the registry file:
Local_machine\software\HTC\VolumeOverlay\SavedHand SetVolume
Change DWORD to 0
(soft-reset not needed)
plug in the headphone and adjust the system volume (press the volume button on side of the device and adjust the volume that is most soothing through the headset and it will memorize it! Once you pull out the headset the volume through the system speaker will be amplified as set by step 2 below. Plugin the headset again and the vol. will revert back to the headset volume level that you adjusted above).
You can always increase or decrease headset volume using the volume switch from this point and this new level you used is memorized during next headset insertion and automatically adjusted.
Step2,
This will tweak the volume that you want when headset is not plugged in.
But remember this will be the maximum volume through the speaker and you can only decrease it using the device volume button, not increase it.
You may have to experiment a few times until you get to a satisfactory volume level (don't forget to soft-reset after tweaking each time. I found 40 to be quite reasonable.
Local_machine\software\HTC\AudioManger_eng\Config\ music_player_volumn
Change the DWORD to 10 (you may have to adjust it to suit the volume you want when the headset is unplugged. In fact 10 is too low and I found 40 to be more reasonable) or lower(I think even 10 is too low!) and soft-reset the device.
the music will become lighter in the TouchFLO3D music player
I did both of the above steps and it solved the problem dramatically! It works even if you are using other software players(windows media player etc)
Edited by,
Fulham
Originally the solution came from maklik from another forum)
fulham said:
You may edit the registry file:
Local_machine\software\HTC\VolumeOverlay\SavedHand SetVolume
Change DWORD to 0
(soft-reset not needed)
plug in the headphone and adjust the system volume (press the volume button on side of the device and adjust the volume that is most soothing through the headset and it will memorize it! Once you pull out the headset the volume through the system speaker will be amplified as set by step 2 below. Plugin the headset again and the vol. will revert back to the headset volume level that you adjusted above).
You can always increase or decrease headset volume using the volume switch from this point and this new level you used is memorized during next headset insertion and automatically adjusted.
Step2,
This will tweak the volume that you want when headset is not plugged in.
But remember this will be the maximum volume through the speaker and you can only decrease it using the device volume button, not increase it.
You may have to experiment a few times until you get to a satisfactory volume level (don't forget to soft-reset after tweaking each time. I found 40 to be quite reasonable.
Local_machine\software\HTC\AudioManger_eng\Config\ music_player_volumn
Change the DWORD to 10 (you may have to adjust it to suit the volume you want when the headset is unplugged. In fact 10 is too low and I found 40 to be more reasonable) or lower(I think even 10 is too low!) and soft-reset the device.
the music will become lighter in the TouchFLO3D music player
I did both of the above steps and it solved the problem dramatically! It works even if you are using other software players(windows media player etc)
Edited by,
Fulham
Originally the solution came from maklik from another forum)
Click to expand...
Click to collapse
i just proud of my name is being posted by other
None of these thins work with noise isolating headphones where 1 bar is too loud. As soon as the phone starts to ring you are deafened as the volum is A LOT LOUDER than the music. I have the same problem with WMP as I can set a low volume in system, 3 bars, and 15-40% in WMP or an other program and the music is fine but as soon as the phone rings it absolutely kills!
man if someone solves this they'll make a few insta-friends !
We need a fix.
Many this app will help some, if not all of you !
It's a freeware developed by a member of this forum and it serves the simple purpose of allowing to set "volume steps" and replacing the default volume window. It's brilliant.
Work is still in progress, but it's already a must have at this point
http://forum.xda-developers.com/showthread.php?t=598997

Volume reduction in Froyo?

Has anyone noticed that the volume is lower in Froyo than it was in Eclair?
I've tried a number of different apps (built in player, tunewiki etc.) and there seems to be a definite reduction in the volume since upgrading. Any ideas?
i was going to post a thread saying volume is much better!
earlier on 2.1 it was crap for me. now both in call volume and media volume are much better and in call volume is clearer. the rear speaker sounds less tinny and is passable now. the shrill hiss / tinny sound at max volume is gone now totally since froyo update i think atleast on the tracks i listed to (preinstalled music and soem youtube videos). i was infact thinking i might reduce the volume a bit which seems a bit of a shock to me knowing the crap rear speaker dished out with the desire. earlier i had said elsewhere that this was the worst speaker i had seen on a phone compared to any of my phones in the last decade, but now i retract that statement. looks like it was a software issue.
i had before the froyo update installed the free 'car mode' app that uses the rear speaker, i would use that mode when ever i put the phone in my trouser pocket as otherwise i would never hear the notifications and often the ring if i was out and about. then after fiddling around i found some sound settings which wasnt obvious at first and disabled the default tick box that made the ring volume and notification volume the same. after disabling that tick box then i could independently adjust the notification volume.
also before the froyo update i installed the free 'quick settings' app which under its settings has a setting for sound, under that apart from the usual volume controls, it has a separate control for system volume which i couldnt find elsewhere on the phone and after increasing that system volume to max, the volume output improved from the rear speakers.
but after froyo it is even better now, both for call volume from earpiece and rear speaker. i cant comment about the earphones as have never used them yet and still in its packet somewhere. wish there was a way to use the fm radio without needing the earphones.
Interesting..I'm specifically speaking of the headphone volume and the ringer volume. It's certainly lower (around 30% lower than 2.1).
I do agree the output from the inbuilt speaker is improved.
Upon further research, I have seen others mention similar issues and also relating to the quality of the sound. I've also seen custom roms using pershoot's audio mod which is supposed to increase loudness. Can this be applied to a stock 2.2 rom (rooted of course)?

Audio volume too dam loud (at night)

When in bed, just before going to sleep, I enjoy listening to music on my phone. The surrounding environment is very quiet (it's night) and my in-ear headphones (sony extra-bass canal headphones) are simply amazing at noise cancellation. With these two factors in play even the lowest volume setting is too loud for half-awake type music enjoyment. I don't want to lower total volume range since if connected to my car stereo and set to max volume the media volume is perfect, no need to fix that range, it's the lower range's increments that bother me.
Is there a mod, tweak, or an app would could give us a much finer control over media volume? I really liked XiiaLive's internal volume slider that worked independently in addition to android global media volume, but now after they tied those to be the same the 0% volume and the next step up are too far apart... >(
Hopefully I'm not the only one with such needs. Thanks for any suggestions that you guys might have
frifox said:
When in bed, just before going to sleep, I enjoy listening to music on my phone. The surrounding environment is very quiet (it's night) and my in-ear headphones (sony extra-bass canal headphones) are simply amazing at noise cancellation. With these two factors in play even the lowest volume setting is too loud for half-awake type music enjoyment. I don't want to lower total volume range since if connected to my car stereo and set to max volume the media volume is perfect, no need to fix that range, it's the lower range's increments that bother me.
Is there a mod, tweak, or an app would could give us a much finer control over media volume? I really liked XiiaLive's internal volume slider that worked independently in addition to android global media volume, but now after they tied those to be the same the 0% volume and the next step up are too far apart... >(
Hopefully I'm not the only one with such needs. Thanks for any suggestions that you guys might have
Click to expand...
Click to collapse
WinAmp from the market lets you adjust the gain or the ADP mod for your ROM can do the same also, along with a few other things. Personally I use ADP because it makes everything sound better and I hate hitting the pause button on my headphones and having 3 different music apps turn on.

Disable absolute volume broken?

When I "disable" absolute volume for use with poweramp the volume is QUIETER. I thought enabling this option was supposed to have an opposite effect? Instead it makes it half as loud now. I wanted to use the DVC option with power amp on my bluetooth but that seems to be a no go. Some devices are quieter than others. One pair of bluetooth earbuds is so quiet you can hardly hear anything unless the volume is maxed. Another is low but not that bad. Is there something I can do to fix this? Everything I read says this is the opposite of what should happen.
I have exactly the same issue with Poweramp. Not sure if it is the app or Samsung changed something. It worked as intended in previous versions of both Poweramp and Android

Categories

Resources