XDA star stuck in Boot-Mode - need help ! - Upgrading, Modifying and Unlocking

Hi i am a newbee in this forum and i have trouble with my XDA star (nike), because it stucks in boot-mode and i can not get it alive....
Her is what i did:
- i installed the CleanBlack2ReloadedOffice in german on my XDA Star - it worked perfectly ...
- Today i wanted to upgrade the radio from Nike_Radio_1.58.16.27 to the better one Nike_Radio_1.58.21.23_25.65.30.04S_Modded.
Result: the flashing stopped with 99% an now i am stuck on this boot-screen and my phone is a brick :-( It says:
RUUNBH
NIKI300
SPL-1.16.0000
CPLD-4
I tried several things to get the phone alive - but nothing helped every trial failed with the grey screen and a 0% on it - some 5 Minutes later aborted with error.
I copied the sspl-1.16-nike.exe on the device and started the Update. It stuck on 99% - ended with an error.
But now i am not able to install hard spl or anything else? I allways get the 0%-Load-Screen on the device and after 10 Minutes an 262-Error.
I tried now to load every shipped original rom - but the Rainbow-Start-Screen does not go away. Is there any other chance to get this device again working? Did anyone made experiences with this strange behavior?
I really would be glad, if there is a "howto" get into a working communication process between my "Pc" and my phone? Is there hope to get this device running? Any helpfull advices? Thanks in advance

Related

hello all! please help

Hi to everyone on the forum,
right here goes
Tried to do a ROM upgrade on my EXEC, but it crashed half way through!
Now got boot loader screen etc and try to run ROM upgrade again, it completes
but when i do the reset all I get is a screen full of different coloured bands!!
what am i doing wrong?
all help much appreciated

Need help ! cingular 8125 bricked :(

Hey iam new to this upgrading,CID unlocking etc.
I just bought my Cingular 8125 three weeks before.
I tried upgrading to WM 6.0 The update process completed successfully but after the reboot my mobile was back to factory default with wm 5.0.
without tring the lokiwiz to unlock, i used shelltools to flash the wm6.0.
it was successful, it asked me to do a hard reset.
Since then i am stuck up with the boot screen.
I can't get my Mobile back working.
i tried flashing with the Offical rom but of no use.
i have tried button rom, love rom. nothing works out.
without much knowledge i upgrade my spl & IPL to 3.08
now i am not able to downgrade that too.
tried flashing different roms but of no use, still it stucks up in the boot screen.
the only hope iam having is i am able to get into the boot loader.
I am not sure, where to post this thread, my appologize if i have posted in the wrong page.
below is the information i have on the screen
IPL 2.26
SPL 3.08
GSM 01.12.10
OS 1.5.4.2
Some one please help me out. i am very much worried, any help is very much appreciated.Thanks a bunch in advance !
dosai.
Have you tried flashing from the bootloader to an official rom?
thanks for reverting, i have tried that too, but of no use.
Sounds to me like you didn't run the Cert_SPCS and EnableRapi cab files before flashing with ShellTool. Being stuck at the splash screen is a dead giveaway.
I never did understand why someone would attempt to flash a ROM without doing ALL the steps. . .
i did ran Cert_SPCS and EnableRapi cab before running the shelltool. shell tool took around 10 mins to complete the update.after restart, my phone stucked up in the boot screen!. (i remember not unlocking the cid before proceeding with the shelltool) .
is there any way to get the mobile working i am too worried.
Solution
Hi, press and hold the CamShot Button and press the Power button, when you see a multi-color screen you can make a update again.
Hello all Im new here and have the same problem. I followed all the steps and followed all the instructions to fix this problem but nothing. I am stuck on the multi-color screen and i can't do nothing! HELPPPPPPPPPPPP!

help me plz i am stuck in os screen after try to update from schapes 3.3 to 4.0

hi plz every one who can help me it very urgent..
i try to upgrade my friend htc hermis but i am stuck in os menu
previusly i install scap rom 3.3
i treid to install the new version it reached 2% and the an error massege appear (connection error) then i tried to do it again but evry time i try the same maasege appear on the phone (coonection error )
it reach 0% and this message appear
i have spl 1.09
i also tried to hard spl it but still the same message ...
i treid different usb and pc but still
i download an official rom the same message
i sleep a see the same f*cking message
plz help me
IT Would help if you Gave the Error Message # for Example If your Getting Error Message 240 It's a Connection Problem.
Try Turning of your Firewall, Have the Rom you are upgrading to in your Root Directory And Always Make sure your Phone is Super CID unlocked.
Hope This Helps.....I"ve been where you were at once... IT was the My Firewall for me.
Try flashing your Operator rom using the SD card method. Or looking at the Unbrick table done by POF. It's all in the WIKI...
halder said:
hi plz every one who can help me it very urgent..
i try to upgrade my friend htc hermis but i am stuck in os menu
previusly i install scap rom 3.3
i treid to install the new version it reached 2% and the an error massege appear (connection error) then i tried to do it again but evry time i try the same maasege appear on the phone (coonection error )
it reach 0% and this message appear
i have spl 1.09
i also tried to hard spl it but still the same message ...
i treid different usb and pc but still
i download an official rom the same message
i sleep a see the same f*cking message
plz help me
Click to expand...
Click to collapse
Try booting in debug mode (hold the Side OK button + power button and reset at the same time)
once you booted into that 4 colored screen with SPL/IPL listed, flash the device with HardSPL 0.7
Link Here
Then upgrade your device again.
using HardSPL it ensures your device will not be overwritten with bad blocks and it enables unsigned rom files to be written to the phone. it's a win-win if you upgrade it.
still the same message 262 update error.
i triecthe hard spl but s6s error always appear
i can go to boot screen
plz if there solution tell me..
its not afirewall fault..
halder said:
still the same message 262 update error.
i triecthe hard spl but s6s error always appear
i can go to boot screen
plz if there solution tell me..
its not afirewall fault..
Click to expand...
Click to collapse
This 262 Error Message I got this
""ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.""
At this Point I"m Stumpped I"m hoping one of the Big Boys Will Step in on this one and give you a better Solution....
yes it reached 2% then it stuck there i treid to reupgrade with the same rom no luck..i tried different rom also ..
do u think if i download a shiped htc rom it will work
halder said:
yes it reached 2% then it stuck there i treid to reupgrade with the same rom no luck..i tried different rom also ..
do u think if i download a shiped htc rom it will work
Click to expand...
Click to collapse
Wam7 has already given the best advice to start unbricking your phone.
1. Get the original Rom which came with your phone. It might be listed here http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades or here http://wiki.xda-developers.com/index.php?pagename=Available Original Shipped WM6 ROM Versions. If it is not listed you'll need to search the internet and/or this forum.
2. When you have your original ROM, flash it to your phone from the SD card, not from your computer. Instructions to do this are here http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing. Remember to have a full battery charge before beginning.
Hopefully this will recover your phone. If it does, then make sure that you flash Olipro's HardSPL 2.10 (V7) to your phone http://forum.xda-developers.com/showthread.php?t=296722.
If you get stuck on how to do this correctly, there is some good advice in Mrvanx's upgrade guide http://forum.xda-developers.com/showthread.php?t=299462.
Also, in the future it can help others to help you if you give more information about your phone such as phone type, original ROM, current Rom, Radio version, SPL version etc, etc. Most people include some of this info in their signature so they don't have to keep re-typing it.
thank you very much for replaying...
i tried the sd card method and i download my exact cid rom but still it give the error 0068002 i download more than 5 original shiped rom same message
my phone is htc ...tytn ..not qtek or dopod ....
htc pure
info
r 1.18.00.10
g 32.55.7018.01h
d 3.57
m05 s04 b06
any other solution
i can go to boot menu
plz again
i tried evry possible way to flash my phone but i cannt get it done why??? EROOR 262
i download more than 10 official rom (htc) and i apply the exact sd method steps still it give me 0028002 error
my device is HTC ...BUT HTC WHAT I DONT KNOW...IT JUST HTC ONLY
SO I CANNOT CHOOS MY EXACT CID ROM
PLZ HELP ME OR I WILL THROUGH IT AWAY
plz answer me its very urgent?????
ok i dont want to open a new thread with same question.so if some one plz can help i will be graetful....
i want to knew how to fix error 262
Have you tired flashing from the bootloader?
Have you tired flashing just the rom from mitty ?
Is the phone unlocked? Have you thoroughly read the unbricking thread in the wiki?
WB
i dont know if its unlocked but i flash it with chap 3.7 a then i tried to flash it with chap 4.00 it reach 2% and stoped..ofcouse its unlocked..
it tried the mitty way but it give
level=ff instead of 0
and bad command
it tried the sd card method the error 0068002 or invalid vender id
If you get invalid vendor error doesn't that mean the phone is locked?
since no one helped me here in this thread ...i helped my self..
i found the solution...i send my ID to htc.com and they replay nicey and send me the link to my exact cid rom ..
the problem was my original rom was norway not wwe ..**** who thought that???
anyhow thank you for all who tried to help me..really i benfit from thier method for future desaster???
see u in another problem...
cuz we know nothing we just ask and ask until we find the solution ..

Bricked G Pad V500; Tried Everything

Hi all,
I just bought a Nexus 9 and I am selling my G Pad to a friend. I was running the V18 build and been happy with it ever since it appeared. However, today I tried to factory reset the device and it just boot looped complaining of a secure boot error, presumably as I was rooted. I tried to restore the tablet by using the official LG tool and the "Update Recovery" method yet that fails at 4% each and every time. I then tried to do the method found here (which I remember working, but not sure how I got it to work months ago). http://forum.xda-developers.com/showthread.php?t=2692505
I have the drivers all installed okay, the PC is finding the tablet fine, however when trying to flash the TOT file I get "Download Fail" at the same point every time with an error like "00064" every time. I think this could be due to the low batttery and I have no left it charging in download mode (if this does charge?).
I'm not sure what else I can try now, the tablet is stuck in download mode and I cannot do anything with it, any help is appreciated and I can provide info to be more clear if needed.
Thanks all,
Tom.
Hi, I've had the same problem. For me the only solution was to install Windows XP (English version) and the progress bar magically skipped 4th percent. I think it has something to do with LG TOOL not being compatible with some Windows (languages) versions. You can give it a try, please let us know if it worked.

Failed to get PMT info, is it bricked for good?

Hi,
So today suddenly my phone restarted and after that it was stuck on the micromax logo, I coudnt get into recovery either. So I tried to flash the stock kitkat rom using sp tools, it did manage to flash it the first time but the phone after that wont start at all, nothing not even the charging screen.
Is it bricked for good? I tried to flash it again but if I choose firmware upgrade or download+firmware upgrade in sp tools I get the pmt info error. Is there any way to get the phone back to a working state? Any help would be much apprecited.
Note: I did look through the old post on the similar topic where the guy managed to solve the problem by using a latest version of sp tools, Im already using the latest version , no dice.
Did you get anywhere with this to unbrick the device as I have similar with a GDP XP and it wont now boot or show charge its just dead!
Any help on fixing this would be great as we cant be alone with this. ATB

Categories

Resources