Related
My Pda 2k device i tryed to upgrade it from 2003 SE to 2k5 after pressing update the device restarted gived me a gray screen and typed on it seril and at the buttom v2.02 now i cant open the device each time i reset or heard rest this is the only screen appears to me i cant even connect to activsync please i need your help what to do to get my device back, this error message i recived (usb device not recognized aslo active sync didnt recognize it)
i need to add a point the device is not working on the USP connection as it have a problem only serial port to connect with the pc
i'm so new here please help me
not to worry.. you can perform a hard reset of your 2k3 version "power+reset" to get you back to at least a working device.. I have been through this and have had this happen to me as well.. try entering bootloader again "power+record+reset" and dock it fairly quickly and it should change to USB on the screen and PC recognize it... also for anyone reading this.. I would highly recommend plugging your cradle into a 5v power supply as I can only imagine most of the bricked BAs are probably due to a computer freezing and/or the PC shutting down power to the USB port only for a fraction of a second and hosing the flash up.
THx Man i will try i hop this will work :lol:
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Try this it shld work
hdubli said:
This is based on my experience with two UNis..one Exec and other JASJAR..both had same problem...this is how I solved :
-Put yr device in bootloader Mode
-Disable USB in Active Sync
-Now connect woth USB cable and open mtty utility
-Select the "WESUSB... " port
-You shall see a blank white screen..press Enter to get "USB>"
-Then type ( as BUzz has informed) set 14 0
(here I wud like to inform that after doing the above I did not get success so I typed set 14 10,then set 14 9 for two three times)
-Then I ran the ROM Upgrade directly(After enbabling the USB)
-I then followed the procedure as informed on the COngratulations Screen that is hold the two "-" buttons and soft reset and then pressed 0
-I got them back to normal..
I hope this helps to all my friends...Pls feel free..pls do not trouble our Buzz..he might be busy in inventing something more to our devices
Click to expand...
Click to collapse
Guru Meditation said:
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Just noticed your user name, I was a big Amiga fan a few years back, still fire up Amiga forever occasionally on my PC when I feel the need.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Click to expand...
Click to collapse
Try it with a different USB cable or in a different USB port (don't go through a hub and if you've been using a laptop then try it on a desktop PC since some laptops have hubs built into them). If that doesn't work then you're out of luck as your Universal isn't detecting that you've connected to your PC and its time to send it in for repair.
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
i am stuck on the same problem and wondering the forum for almost 3 days now with no luck.... please help my device is in boot loader mood but not turning the serial to USB ......... please HELP.......
solution
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Please follow the steps:
1. Plug in ur usb cable in bootloader mode while it is showing 'serial' and version 'x.xx'.
2. Soft reset by pressing Backlight+power+reset pin WHILE KEEPING THE USB CABLE CONNECTED
3. your phone will now reboot into 'usb' mode. Don't remove the usb cable yet.
4. Remove the Memory card while keeping the usb cable still connected and VOILA,your pc starts recognising your phone as Microsoft usb sync.
5. Do whatever you want to do now (upgrade)
Hope it solves the problem now.
Press thanks if it does.
Something else to try
Having had a few issues with my G3 Uni, I've been through my fare share of Uni bootloader issues. When I find that I can't get the 'serial' to go to 'USB', I normally find it's because I haven't taken the memory card or the SIM card out (usually the memory card).
Make sure your memory card is out, then try to enter the bootloader and see if this cures it. If it does, then use mtty and the command 'set 14 0'
This tells it to reboot on reset. if you were to use 'set 14 1' it would go back to the bootloader on reset.
my Htc hd2 t-mobile won't recognize usb on boot-loader mode
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
kaleb2954 said:
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
Click to expand...
Click to collapse
you have the wrong forum friends! This Htc Universal section
to update Android on HTC HD2, you can use the Clock Work Mod Recovery !! for more details should refer to this thread http://forum.xda-developers.com/showthread.php?t=1021837
I-MATE JASJAR hung
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
bechir2013 said:
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
Click to expand...
Click to collapse
look here
http://forum.xda-developers.com/showpost.php?p=5456317&postcount=6
the first point...
A lot easier than to root this device
As the title states: Why does some computer fail to recognize the Universal via USB on bootloader mode?
I recently reformatted my computer, which I usually do once a year. After installing all my apps back and running windows update on my computer, I installed active sync. Performed a normal reset on my computer, attached my Universal and active sync worked.
Here comes the problem: I decided to roll back to my old AKU 2 QTEK ROM. Of course, I know how to use the Ma_Upgrade No ID file. The problem is my computer now fails to recognize my Universal no matter what I do on bootloader mode. To make it worst, I am now stuck at the bootloader mode with my computer not recognizing it. Any suggestions as to why my computer failed to recognize my Universal?
OK, I was able to get the ROM upgrade going again, by removing my SIM Card and 4GB SD Card. I'll post back if I was able to revive my Universal.
So it seems that my computer failed to recognize my Universal because either the SIM Card or SD Card is causing the conflict.
I had the same problem.... I have two computers one with Win Vista (with the same problem) and another with XP sp1. This computer recognize my pda in boot loader, doesn't matter if still SD card and SIM inside....
Sorry for my english and I didn't tell you a solution...
Hi,
i had the same (very annoying) problems but i always was able to get the Universal back into Windows Mobile.
It was very strange because i started the ROM update and than e.g. it did not go in the Bootloader but back in Windows Mobile so i started it again and than it stucked in the Bl. Hardreset and putting the device again into Bl did not help and i was already very annoyed. I tried to plug in and out the USB-cable but it was always telling me SERIAL and not USB and Windows showed this ****ing popup that one device is not recognized or something like that. I tried a trick to let the cable plugged in USB and than reset and it showed me USB but wheter MA_Upgrade (No ID of course) nor mtty were able to find the device. After several trys and resetting and resetting again i was able to bring it into USB but MA_Upgrade did not work.
The only way to bring back the device from the Bl is the method described in XDA-Wiki (http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen)
The problem is that this method does work only half. I did the steps until the command "set 14 0" and started MA_Upgrade BUT it always told me that the device is not connected, it never worked. I was already frustrated so i did again the reset and what happend? It started back into Windows Mobile!
So what i think that after using the command set 14 0 AND running MA_Upgrade reactivated the start of Windows Mobile. I tried the steps very often because i tried to find a solution for the contacts between WM5 and AKU 3.2 or higher but the only way is to ActiveSync them. This really works and this is for sure the guaranteed way to get (at least my) the Universal back to Windows.
Btw for the people who are to lazy to use the search function:
The damn ROM upgrade does NOT work on Vista until now! Even not with the Windows Mobile Device Connection Center (or how it's called). I tried several steps on the RTM Vista but it never worked. Don't waste your time on it!
So far from my side, i hope these experience will help some people
I Got It To Work!!!
I was so worried. Wheeeeew! Anyway back to normal again. I got it to work.
My observation is: My computer failed to recognize my Universal because I was using Active Sync Version 4.5 Beta 2 to update my Universal. The solution is to completely uninstall active sync using the windows remove program under control panel, and manually deleting the active sync folder from the hard drive. I then installed Active Sync Version 4.1 and all was well again.
So my next question to all the guys/gals who had problems with upgrading their device because the computer FAILED to recognize their Universal via USB is: ARE YOU USING THE BETA VERSION OF ACTIVE SYNC?
Actually when you try to upgrade with SD card inserted - only then you will get this error - I spend so many hours of GOD prays for my Universal - and after that I just remove a SD card and everything is back to normal
agisofttm said:
Actually when you try to upgrade with SD card inserted - only then you will get this error - I spend so many hours of GOD prays for my Universal - and after that I just remove a SD card and everything is back to normal
Click to expand...
Click to collapse
What is the size of the SD Card you are using? Because when a 2 GB SD Card is inserted, it works just fine. But I experience the error with my 4 GB SD Card.
Unfortunately, i don't share the same luck with all of you.
I've already take out both SD and SIM and try thousand times with ActiVeSync 4.1, 4.2 and 4.5 beta, softreset, hardreset, mtty'ing, but what i got? BIG ZERO.
So my pc always recognise my ppc as "Unknown Device" and there is no, even some slim chance, to get it to work.
Any idea for reviving my uni from black slumber of bootloader screen?
Any help would be appreciated.
DuLanTus said:
Unfortunately, i don't share the same luck with all of you.
I've already take out both SD and SIM and try thousand times with ActiVeSync 4.1, 4.2 and 4.5 beta, softreset, hardreset, mtty'ing, but what i got? BIG ZERO.
So my pc always recognise my ppc as "Unknown Device" and there is no, even some slim chance, to get it to work.
Any idea for reviving my uni from black slumber of bootloader screen?
Any help would be appreciated.
Click to expand...
Click to collapse
use MTTY with "task 28 55aa", "set 14 0", "set 14 9, "set 14 10" and "set 14 20" as described. bootloader screen may be replaced with a blank one, boot it on bootloader mode by "Backlight+Power+Reset"
http://wiki.xda-developers.com/index.php?pagename=Universal_Resets
now upgrade as usual, then If you stuck on the bootloader again after upgrading, try to upgrade the bootloader itself
go to
http://forum.xda-developers.com/showpost.php?p=1255206&postcount=52
i have done all this... but there is something with vista... they do not recognised it when it is on bootlad screen... what should i do can anyone help me??
moixalakix said:
i have done all this... but there is something with vista... they do not recognised it when it is on bootlad screen... what should i do can anyone help me??
Click to expand...
Click to collapse
Hi, yes you could be bang on in saying there is a problem with vista, my machine did that as well, I really thought I'd turned the phone into a brick, luckily I've got an xp machine that let me connect with the tools that everybody else is talking about here, the one I used was UNI_ExitBootloader.exe (from this site somewhere) which sends all the codes for you and it only worked from the xp machine, it totally failed on the vista machine.
Tried all suggestions, but no luck
So a failed upgrade has left my Uni stuck in bootloader mode saying "Serial" and "v1.00". When I plug the thing into my Windoze XP machine with Active Sync 4.5 one of three things happens seemingly at random:
1. My mouse stops working
2. It tells me that the USB device is malfunctioning and cannot be recognized
3. Nothing happens
In all cases the Uni still shows the same "Serial" message.
The Uni has no SD or SIM cards in it. I have tried hard resetting it. I've removed and reinstalled Active Sync. I've rebooted this windoze pile of crap about a thousand times.
Anyone got any ideas?
Thanks,
Saline
Welcome to forums
Have a read here:
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Hope it helps,
Hi. Thanks for the quick reply. Unfortunately I have already tried the suggestions on that page (that's how I found this thread). As I mentioned above, the device has no similar nor SD in it.
Have you tried to reflash from SD card?
instructions on the link on my sig
My Wizard is stuck in the RUU bootloader screen and Windows XP comes up with the error "USB device not recognised".
When I connect to Windows XP the bootloader sceen shows USB at the bottom left but the PC (tried on 2 different machines) shows the above error.
Hard reset and soft reset do not work.
How can I get the Wizard to connect with the PC to perform a rom install or is the Wizard now beyond help ?
forcedv said:
My Wizard is stuck in the RUU bootloader screen and Windows XP comes up with the error "USB device not recognised".
When I connect to Windows XP the bootloader sceen shows USB at the bottom left but the PC (tried on 2 different machines) shows the above error.
Hard reset and soft reset do not work.
How can I get the Wizard to connect with the PC to perform a rom install or is the Wizard now beyond help ?
Click to expand...
Click to collapse
If the phone is already unlocked, plug the phone in the ocmputer. It should say USB on the phone when your on the Tri Colour screen. From that point you should be able to just flash any ROM you want. As long as it says USB on the phones screen, you should be good
No, that does not work beacuse when I run a rom install utility, I get the error (device not found).
If the pc does not see the phone, the flash utility will not either.
Is there a driver that can be installed on XP to force it to recognise the phone when connected to USB ?
Any help with this problem would be a life saver.
forcedv said:
No, that does not work beacuse when I run a rom install utility, I get the error (device not found).
If the pc does not see the phone, the flash utility will not either.
Is there a driver that can be installed on XP to force it to recognise the phone when connected to USB ?
Any help with this problem would be a life saver.
Click to expand...
Click to collapse
Are you unlocking are flashing
What knid of phone do you have
It's the HTC Wizard thats been running WM6 (TNT).
The trouble began when I tried to flash the latest version. The Wizard was recognised and the flash started, but at 0% the USB connection was lost.
Now the PC will not recognise the phone and it's stuck in RUU bootloader screen.
Tried all the USB ports on 2 different Windows XP PC's. Same problem.
Is there any method to get out of this RUU bootloader screen besides the soft/hard reset methods (because they do not do anything) ?
If the phone is already unlocked, your on the bootloader screen and the phone says USB. I don't see why you can't flash any ROM you want. I have never encounterd this issue.
yep, it's a new problem for me too.
Bottom line is, if I can't find a driver or some other way to make the PC see the Wizard. It maybe time to bin it :-(
Mate...I feel for yah, I got the same problem and tried everything. No one has come up with a solution for the phone and the PC to connect via USB when you get this error.
forcedv said:
yep, it's a new problem for me too.
Bottom line is, if I can't find a driver or some other way to make the PC see the Wizard. It maybe time to bin it :-(
Click to expand...
Click to collapse
I dont know much about your phone but can you flash from SD card ?
It might be in the wiki section for your phone
here
http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard
it may be related to a faulty USB cable... or loose USB... i have mine do that sometimes and i have to make sure i do not move the usb once it is active synced!
LOL
Hi guys, sorry for my bad english.
Since today can't sinchronize my ppc with wm 5.0.
Here's the problem: when I pug it with usb cable, nothing happens.The orange light is on, the phone is in charge but nothing happens.Usually when I connect the phone I can see windows looking for ip address, and the activesynch shows... but this is not going to happening anymore.
I tried to reistall activesinch, I've cleaned the registry and i tried to connect it with others software.Still nothing.
Firewall is disabled.Any solutions?
Thank you in advance.
Zealot87 said:
Here's the problem: when I pug it with usb cable, nothing happens.The orange light is on, the phone is in charge but nothing happens.Usually when I connect the phone I can see windows looking for ip address, and the activesynch shows... but this is not going to happening anymore.
Click to expand...
Click to collapse
I had the same problem sometime ago. I've changed the wire first but nothing happened. My speaker, my Mic was dead and I could switch on FMRadio without the Hands-free!!!
What I did...??? I updated my mobile's Radio with 3.39.90 Version. How can you do this without active sync???
1. Remove SIM Card and Storage Card from the Mobile.
2. Press and Hold the Right Button (Recording Button) and Press together the Power Button. You will be in the Bootloader Screen. Try to update the Radio first.
3. Check it if it's working ok.
2nd way...
1. Copy the official ROM of WindowsMobile to the Storage Card.
2. Press Right Button (you know the Voice Rec) and holding that press the Power Button...
the mobile will be bootloader mode and will try to install the official ROM from the Storage Card...
wait a bit and then when it finish, check it if it is working properly!
Hope to help... waiting to "hear" sorry, to read good news
I have the same problem i cant sincronize the pda whith the activesync and i wish to change the rom. Now it's in france and i wish to change it to english, and it's locked to orange france i think. What can i make? It starts in bootloader, but the instalation from the card is not starting. thankx
le. and if i want to install something gives error 260
I had the same problem 1 month back, checked the mini usb data cable with a multimeter just to find that one of the data TX/RX wire was short with +5v wire, cable was faulty. the 1st and the last wires (+5v , -5v) were ok thats why it was charging the phone, but not connecting to pc, it was giving error unrecognised usb device.
u can also check for bent contacts at the USB mini connector on ur phone.
strange
hy guys
i´ve got a strange problem with my arte110.
for some reason i cant establish an activesync-connection,a few days ago i had some wm6.5 rom running and couldnt connect my device, then suddenly today (maybe because i reinstalled windows on my computer yesterday, i dont know) i was able to connect the phone while in bootloader... so i flashed happy and lucky the original wm (os 5.2.1620 build 18125.0.4.2) rom i got from t-mobile austria.
now its the same problem as before, i cant connect my device, i've restartet artemis and my computer several times, i've reinstalled activesync 4.5 a million times, i've tried all available usb-ports- different usb cables (same cable works with external harddrives) and even my office-computer, and so on...
my pda is (and was allways) charging but i cant syncronize.
has anyone any idea what could cause this problem?- please don't tell me the usb port of the pda is damaged, I wouldn't want to have to fix anything in this case...
hoping for good news, McPerfuntory
[by the way, please dont judge me for spelling mistakes, i'm from austria!!!]
done
okay guys, no need to respond anymore, i got it right..
but i don't really know how i repaired that one, i disassembled the devive cleaned everthing in there and cleaned the usb connector..
..works again