hi all, my diamond doesn't stop at the bootloader tricolor screen instead it loops a inifinite usb connection error in a white screen(similar to flashing rom from device screen).
previously, i had the device wth hardspl, den i flashed a original official rom, followed by flashing the stock spl. the problem arise after that. The phone goes into windows mobile though, no problems..
appreciate any advice given. thanks.
Related
Hi,
after successfully flashing a lot of roms I finally landed on touch 2.1 and the gps didn't work anymore. I reinstalled factory rom and now I am unable to install anything new since with uspl there is a white screen and no usb connection afterwards. And with ruu it stops at 2-3% saying it is a corrupted file or the wrong ruu.
<br>I have the orange spv m650 and am trying everything to get a new rom on it.<br> I akso retried the two steps .bat from meschle. But that didn't work as well.
<p>Any help possible???
Dear Sir
My diamond got stuck up at the welcome screen or else in the alignment screen. I've flashed many roms number of times before but this time this happened after a hard reset- using Macadam 1.2 (latest).
My bootloader reads - Diam140 MFG 64M; SPL-1.40. Olinex. After this I've flashed back to the latest indian stock rom i.e. First to (RUU_Diamond_hTC_Asia_India_1.93.720.4_Radio_Signed_Diamond_52.62.25.34_1.13.25.24_ShiP) but know result & (RUU_Diamond_hTC_Asia_India_1.93.720.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.07_Ship_R). After going through the forums- I understood that I've to step down to stock spl. But even after successful flashing, the boot loader shows the same- "SPL-1.40.OliNex".
I'm unable to use the jump SPL, because I can't pass through the alignment screen. Please help, is there any way to JUMP SPL without operating the phone.
Or else how can I come back to the stock spl.
Please Help.........................
Regards
Furthermore, I've tried using mtty to following the procedure:
Correct sequence is as follows:-
1. Launch ActiveSync on PC
2. Go to connection settings
3. Uncheck the Allow USB Connection
4. bring the device to bootloader. AND connect to the PC.
5. Now, run mtty1_1_.42_538 on PC.
6. CMD>task 29
7. Flash the ROM of your choice
Then flashed the stock rom again. But the problem remained.
jockyw2001 - suggested me on PM to do- "in mtty: set 16 0 then reboot'- but nothing happened. Or I didn't follow the correct steps... can anyone explain & help please....
[UPDATE]where do I get the commands for mtty
Can anyone tell me the link where I can get the commands to be used in mtty... Is there anyway to bypass the screen alignment part during start up after a hard reset.... how can I JumpSPL in a handset where the touch screen is not working.. but the screen is not completely dead, i.e. on tapping the "+" sign is moving after around 5 or 7 mins of the tap...
Please help guys.... I'm waiting to be rescued by some WM wizard from this great community.....
Regards
wizards- all'r failing or what- very few people with clear funda
cmonex please help....
hi man
i had the same problem, with all the rom around
than i understand that the problem was the radio rom
try to flash the lastest radio..i use the 1.13
Flash a Rom without screen alignment
Hi
If you on bootloader and you have 1.40olinex then flash a 1.13 radio then flash a Rom without Screen alignment process. It might help. Good luck
Ok so i just recently got a Verizon XV6900 (Vogue), i tried flashing the NFSFANS wm6.1 and wm6.5 roms but both of these would constantly cause my device to reboot if it wasn't plugged via USB. So i tried reflashing it back to the original 6.1 pro that came on the phone by using the one from the HTC Website, that failed after 31% and i had to recover it. Now the device is just stuck at the screen with the 3 colors with the message
Vogu100
SPL - 2.01.0000
CPLD-3
i have no idea what to do to get out of this, sorry I'm a complete noob and I tried searching but I couldn't find what i was looking for
Any help is appreciated
Your Vogue is not unlocked. Try running the unlocker (.40) again. Once that is done, unlock using the 2.31 unlocker. You should then be ready to flash a custom ROM.
EnZandOutZ said:
Ok so i just recently got a Verizon XV6900 (Vogue), i tried flashing the NFSFANS wm6.1 and wm6.5 roms but both of these would constantly cause my device to reboot if it wasn't plugged via USB. So i tried reflashing it back to the original 6.1 pro that came on the phone by using the one from the HTC Website, that failed after 31% and i had to recover it. Now the device is just stuck at the screen with the 3 colors with the message
Vogu100
SPL - 2.01.0000
CPLD-3
i have no idea what to do to get out of this, sorry I'm a complete noob and I tried searching but I couldn't find what i was looking for
Any help is appreciated
Click to expand...
Click to collapse
just plug it back in and try to reflash the stock ROM. don't open any programs on your computer while you are flashing. i tried to open a media player to listen to music and it froze the RUU. just flash it again it worked for me.
Hi all
OK, my screen alignment on HD is so messed up i went to downgrade my HD HTC (1.56 Olinex -W6.5Miri) back to its original Orange SPL and OS so i can send it back to HTC under warranty.
Foolishly I changed the HSPL first to original stock so it is now a SPL 1.14.000 (no olinex or anything) in bootloader.
I went to then flash ROM to latest Orange HTC OS release from xda (compatible with that SPL) and just got the 262 error.
So, I have a big problem...
1. I cannot flash any ROM - error 262 problem
2. I cannot cook a new HSPL in any way - error 262 problem
3. Ive got green screen and cannot in anyway load SSPL-Manual-TouchHD.zip and then run it (which normally fixes the 262 error)
4. Ive got green screen so my phone doesnt work
5. tried hard reset - now hangs on loading new OS in green screen
Is it bricked? Is there any software I can use to force load HSPL? I figure my aim is to get the phone back to 1.56 / W6.5 and start over again.
Very curious to see if folk out there have any ideas...
Cheers in advance
in addition
am using W7 on pc and have updated drivers for bootloader usb sync
EDIT: I have now moved this post to Blackstone/Blackstone/ thread.
http://forum.xda-developers.com/showthread.php?t=564409&highlight=bricked
I get the colored boot screen then "loading..." then the phone shuts off.
Any ideas on how to fix this?
TW,
Probably your phone is out of energy...
I feel stupid if it is... I'll slip it on the charger for an hour, thanks.
TW,
Battery was close to dead, duh!
However now it won't progress past the white screen "Loading..."
Thoughts or suggestions.
TW,
Flash from windows using custom rru
Making some progress.. Got a link to a good ruu, ATT?
Thanks,
When trying to flash via USB I get the error
"Invalid vendor ID".. then it quits and reboots.
TW,
Did you install hard spl?
Yes, it has hard spl.
Should I update it with a more recent version?
Try with 3.29
The soft SPL is 1.39... I'm getting a communication error now, could it be Windows 7?
I'll try at work in about an hour... thanks.
TW,
Did you follow this guide?
http://forum.xda-developers.com/showthread.php?t=433835
Already had a custom ROM on the phone so SPL should be there correct?
I'm getting error "262 Update Error"..
Tri-color screen shows SPL 1.93.0000
Trying to flash via SD, downloaded Cmonex's HARDSPL 3.29 SD and phone is just hanging at "Loading..."
I installed Android to NAND, will that have some impact on the restoration? Also will the verrsion of Android installed have some impact?
Finally got a ROM to load using the SD method... got the ROM from here:
http://f1ip.net/plug.php?e=index&f=./Downloads/KaiserFiles/Roms/OEMs
Thanks for all the help and suggestions..
TW,