Related
i was installing new rom on my device.when it was 12%, the computer got locked and i had to reset.Now,my baby did not reflash again.i tried again but himaupragadeutility gave : communication problem. what can i do now? can anyone help me? so a few people know this device, the others even do not know what pda is. what i can do?????????????????????????????
keep on doing a hard reset until you reach bootloader mode. from there try upgrading again. were you upgrading to 2003se or wm2005?
i was installing the rom from 02 web site
i was installing the rom from the 02 web site.i had tried but it did not open boatloader.what i can i do?
anything showing on your xda screen? if it's blank then you have to continue doing hard resets. a buddy of mine had the same problem and he was able to bring it back to bootloader mode after 10 or so hard resets.
if something is showing on the screen (like "usb version...something") then this is already bootloader mode. what you do is put the xda back on the cradle but don't expect activesync to recognize it. just put it back on the cradle and then rerun the upgrade.
hope it works.
rob
there is only o2 logo on the device,i tried hard reset but it did not open boatloader
i"m tryning to upgarte to Helmi_UNI_AKU3[1].5_v1.3.rar
after soft reset the JJ is connected to the PC i"m running activsync
and when i want to update the rom i get the nessage that the JJ is not connected and thaT I HAVE TO Check that the jj is conncted and that the JJ us powerd on. and the JJ stuck on boot screen
my friend told me that there is a" cid locked " or somthing like that
can anyone help me?
thank you
Try using the uniExitbootloader from this thread..
http://forum.xda-developers.com/showpost.php?p=1206663&postcount=2
This will take your universal out of bootloader mode.
Also, read the wiki regarding how to put your device in bootloader mode and then use the included MaUpgradeUt_noID.exe to perform the upgrade
I follow instruction in http://forum.xda-developers.com/showthread.php?t=313486 but after hardreset.
My p800w is stuck in T-Mobile logo and version number. It can't continue booting up to windows mobile.
Question: How to flash ROM without ActiveSync?
How to recovery my Artemis?
Welcome any advice,
Thanks in advance.
Yea me to, mine is now a brick after that upgrade? No active sync connection possible and all I get now is the blue O2 start screen after the hard reset with the red writing and numbers in the top left hand corner..
Phone is an UK XDA Orbit
IPL 1.25.0001
SPL 1.11.0000
GSM 02.67.90
OS 3.4.0.0
HELP!!!!!!!
yeah, I had the same problem and have created a thread for it already. unfortunately I got no useful replies, and it seems that I am stuck waiting for an official o2 ROM so that I can recover my Orbit.
It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???
motomob said:
It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???
Click to expand...
Click to collapse
I read in here that you hold the voice button and soft reset.
Decaf said:
I read in here that you hold the voice button and soft reset.
Click to expand...
Click to collapse
Correct and use mtty
Already see in the forum ....
Thanks guys and apologies for the spelling..I ran the Artemis_USPL before I tried upgrading to WM6 and again have been able to run it after with my new brick now with the phone in bootloader mode but still when I try and run the german ROM update a) it will only work with the german file which freezes @ 3%? This seems to be a known problem reading around and b )when I replace it with the smaller ROM file, 54MB the german one is 66MB, I originally tried to use it doesn't read the ROM file or the update utility doesn't want to read it. I reckon I might be able to get it back if I can get one of the ROM update utilities to read a good ROm file and send it to the phone.
I can;t find this MTTY program to sniff the USB port and return the code of if the USPL util wokred as I think that could be key to all of this.
Can anyone post a quick how to here for
1) install MTTY from somewhere
2) what command to run agaist the phoen to see if the USPL util worked and what values I should be looking for
3) another WM6 ROM version (that the update utils can read) download location I can download from to try and send to the phone using the German update util
Not asking for much am I but I desperately need my phone back WM5 or 6 in the next day or so so really can't send it off.
Thanks
Error message I recive at the 3% stage when using the German ROM and english update util.
use the file attach and read that :
http://forum.xda-developers.com/showthread.php?t=285112
Thanks but I'm not that cleud up on what commands I'm meant to be sending. It works in Bootloader mode I ge a response from the phone by send it a command. But even if I get a response telling me what the CID status is its not much help as I think ti shoudl have tekane BEBEs ROM by now as I've got the german ROMUpdateUtility sending that 54,272KB file to the phone but it stops after 3%. What are my options?
motomob said:
But even if I get a response telling me what the CID status is its not much help as I think
Click to expand...
Click to collapse
That's right. On older models MTTY was quite useful, but not on the Artemis. You cannot use it to read the CID status anyway. If you are not sure about the status, run the USPL tool, just to make sure.
I've already re run the USPL ROMUpdateUtility and it completes 100% okay in bootloader mode. But after I hard reset and then try and flash the WM6 BEBE ROM or any ROM German etc back onto it it either fails with the error code I posted up earlier or gets to 3% and fails.
What are my options at this stage? Does anyone have a link to another ROM I can try like the original WM5 O2 ROM or any other WM6 ROm that might work. I'm willing to give them all a try as it's just a useless phone right now and I haven;t sent it off as 1) I need it before the weekend and 2) As I can flash some ROMs with the USPL and others have done this no problem I really feel there must be a solution as I can still falsh the phone.
What can I say RTFM... I did it all right and I didn't have a brick, I missed out one small detail... loading on the ROM with the extended ROM. All now running and it does seem a little faster than WM5.
Thank you to all those that tried to help out. To the others that are still having probs.. Don't try and run the update in the middle of a busy day in the office whilst trying to manage 100 other things meaning you are probably missing out a line like me...
One question though how do I get back my O2 power and storage meters on the today screen back as I liked them and the WiFi seems to have a bug where when it is enabled and you click on the WiFi symbol up the top it only allows you to switch it on, when it is already on.. so you have to open up the COMM manager to switch it off.
So how did you fix it exactly? I have read this thread thoroughly and can't find out what you did!
ERROR[206] occurs while trying to update ROM to WM6
While tring to update ROM to WM6 on O2 XDA Orbit i encounter ERROR[206].
I wanted to attach the screen shot but dont know how to do that, but anyway what i am doing is i attached my pda to my pc via activesync using supplied usb cord. Everything goes well till i reach a screen where it says "You are now ready to update your ROM image...." and once i click next a progress bar apperas and my pda shuts and activesync exit's automatically and my pda tries to restart with RBG band and some text:RUU, IPL 1.25.0001, SPL 1.25.0000 and USB. And thats it after few seconds or a min i get the ERROR[206] and my pda hangs.
I dont know why Activesysn shutsdown ???
Just an additional in i want to tell that without installing activesync i am not able to connect/pair my pda with my pc. So do i need to install the drivers and then try or it doen't matter cause once i install Active sync i can connect the device.
Please help me with this....
Thanks
unable to load bootloader!!!!!!!!!!!!
HELP!!!!!!!!
I have HTC3300, tried to update rom, now its bricked. I tried to start bootloader by pressing the voicebutton and softreset but loads in t-mobile screen and hangs, im unable to start the bootloader.
Is this end of story or are there any other options to get the bootloader to start????
please help
Bootloader
I had a problem with my phone loaded touch flow 4 and cid unlocking, everything was fine then after a while it froze at boot up.
I look put the battery and did a hard reset, put it into bootloadeder mode, reflashed with a t-mobile rom does not need to be cid unlocked to do that.
Once origonal rom was working, cid unlock again, flashed back to touchflow 4.0 - sorted
Where did you got an tmobile rom from can you tell me. Mine is also freezing on booting almost once every day or so after I've upgraded to 4.0
I switched on my phone today, and it loaded the o2 screen, and now is permanently stuck on the Black and Blue screen.
I using Tom's B&B 4.0 touch-flo rom.
Please help!
try a hard reset, something similar happened to me when i was using a different rom and a hard reset fixed it, hope that helps.
Hard reset is when you push call and end buttons together and insert the stylus?
Didnt work either.
hmm.. maybe reinstall the rom then? Did you install any programs on the phone??
It's not detecting the fone, hence I cant even reinstall the ROM.
Is there any way 2 recover from this? Or did I just loose 700 bucks!?
Even problem whereas I had any concern with this version v4.0…
I flashé my artemis 4 or 5 times, it went super… (I would have of the Juste to make hardware reset…).
Since my 2 last flash, that blocks on the page during more 5min…
Flash after flash, always similar
http://forum.xda-developers.com/showthread.php?p=1445305&posted=1#post1445305
So wait, were you able to fix it?
As of right now my fone is sitting like a brick on my table.
Me I wait, of the blow I do not make more software reset…
I am obliged to await more 5min before being able to type my code PIN.
I do not include/understand, that had ever done it to me before this last flash.
I have remakes a flash, always similar, even while passing by a ROM Orange, as soon as I pass by again in V4.0, that does it to me!!!!
Its been over 5 mins for me and its still stuck on the B&B screen. HELP!
Make a hard reset and change the ROM....v3.7 for exemple...
Yea, I tried reflashing it, but the Rom update utility doesnt detect the fone at all.
Look this :
http://www.forummobiles.com/index.php?showtopic=139079
It's a french but it's easy with photo !
I read it, but because it never passes the boot screen, it never detects it hence it doesnt show up in the device manager.
What 2 do!?
Try hard reset again. What did you mean when you said it doesn't work? It didn't do anything? It tried re-installing and failed? What happened?
You don't need the ROM update utility to do a hard reset.
B&B 4.0 Getting stuck on the windows loader, is a know problem. TRy a hard reset to fix it.
Hard reset: Stylus in the hole on the side, and press the two " - " buttons between the red and green button.
This should fix the problem. Now you can flash another rom into the P3300. I'm, running 3.4 without any problem. I updated it with the HTC Tabs from Tom wich used in B&B 4.0.
The problem is that V4.0 functioned very well on my first flash…
while reinstalling the plug in HTC Home + the file SDK, that is better!!
Normal :
http://forum.xda-developers.com/attachment.php?attachmentid=47324&d=1187262723
Color :
http://forum.xda-developers.com/attachment.php?attachmentid=47329&d=1187264616
File SDK :
http://forum.xda-developers.com/attachment.php?attachmentid=47339&d=1187272601
I may come back, for now my Artemis is sitting, bricked, on my table and I've tried everything.
Someone please tell me what I'm doing wrong?
You need to flash via bootloader - hold record button down and soft reset - you now have multicolored screen - connect via usb and flash - you dont need activesync this way.
I have Dhva_ddt V20 installed....
I tried to install omnia slm/touch player...During installation it got hanged...
I did soft reset but after reset it got hanged on splash screen...
After that i tried to falsh new rom by SD card method.. but not sucessful..
It shows IPL / SPL and "serial" at bottom on bootloader...
I tried to connect it to pC here it shows USB at bootom at bootloader but gives an error..."Use new version of RUU"... don't know what to do?
I am trieng from two days and read a lot but noting help...
alex8525 said:
I have Dhva_ddt V20 installed....
I tried to install omnia slm/touch player...During installation it got hanged...
I did soft reset but after reset it got hanged on splash screen...
After that i tried to falsh new rom by SD card method.. but not sucessful..
It shows IPL / SPL and "serial" at bottom on bootloader...
I tried to connect it to pC here it shows USB at bootom at bootloader but gives an error..."Use new version of RUU"... don't know what to do?
I am trieng from two days and read a lot but noting help...
Click to expand...
Click to collapse
downloaded the newest hardspl and flash that, if that doesn't work download the newest shipped from for your phone from the wiki.
here is hardSPL
and here are the shipped roms
or official AT&T rom with radio stripped out (safer)
Tried ATT rom..But it didn't work
alex8525 said:
Tried ATT rom..But it didn't work
Click to expand...
Click to collapse
Then try your official rom. (I put the custom RRU with the striped one).
Should work. If you can get into bootloader tisnt a perma brick.
also see this thread here, looks like the guy solved a problem like yours
alex8525 said:
Tried ATT rom..But it didn't work
Click to expand...
Click to collapse
Try flashing with SD card! Read through wiki to figure out how to flash through SD card.
I have tried SD card method...
But it shows bootloader with IPL / SPL version and "Serial" at bottom...
It dose't load any thing...
I have tried installing ATT official rom also.. but it says use updeted utility to flash....
I am able to go to bootloader and get USB connection when connect to PC....
But I don't have Activesync installe on PC is it a problem??? and I can't install active sync because of some restriction....
How to come out of this?
Is there any way I can Hard reset phone? Without switch on it?
Please help ...M scared....
I have done hard reset and now I m stuck at white screen .....
Is it bricked?
alex8525 said:
I have done hard reset and now I m stuck at white screen .....
Is it bricked?
Click to expand...
Click to collapse
ok, can you get into boot loader, press ok on left, and power on on right, and stick your stylus at the bottom, all together. Plug USB to PC, with boot loader screen, download the ATT rom mentioned here, and start the process. You have to have activesync 4.5 and .net 2.0 on your PC to have this to work.
Also, you have been given a link above for the official ATT without Radio, and here is the exact instructions on how to flash via SD. what part of any of these do you not understand?
Why would you perform a hard reset right after asking about it and not even waiting for an answer? If you had any doubts you should have just waited. I don't know much about your problem but I would't be taking the chance of doing something I wasn't sure about thats for sure. I really hope you can get out of this mess.
what size micro sd have u got. if it is larger than 2 or its a sdhc than you will not be able to flash sd method.
download another recent rom or just reflash the same dvha rom and do it through active sync on pc.
Finally got it working...
After 3 hard reset now I am out of white screen and now its working.
After 3 days
1. on splash screen
2. on bootloader
3. on white screen
Thank you everyone who have replied and who have atleast viewed.
learning:
Activesync is must for flashin through PC
new way to hard reset (thx wiki)
don't panic...your phone will be working sooner or later, if it was not a flshing that hanged it.
by d way i am posting from phone
alex8525 said:
Finally got it working...
After 3 hard reset now I am out of white screen and now its working.
After 3 days
1. on splash screen
2. on bootloader
3. on white screen
Thank you everyone who have replied and who have atleast viewed.
learning:
Activesync is must for flashin through PC
new way to hard reset (thx wiki)
don't panic...your phone will be working sooner or later, if it was not a flshing that hanged it.
by d way i am posting from phone
Click to expand...
Click to collapse
Glad to here you fixed it!