Unlock error - Upgrading, Modifying and Unlocking

I use tool AUTO_Unlock_v3a.bat or v1 (HTC_Hermes_SIM_CID_Unlock_v3a for unlock cingular 3125).It display error as update. Every time update activesync disconnect to my phone with error "image file corrupted!(standby and hibernate mode : Never). Please assist me !
Thank!

Related

ERROR 120, country id error. With USB v1.00 on my screen

Hi,
I tried to upgrade my MDAc with the rom from TMobile.
During the upgrade my computer asked for this file "wceusbsh.sys".
At that point the upgrade stopped.
No i only see "USB" and "v1.00" on my screen.
The charger led is red.
When trying to upgrade again, i get ether this message:
Error 120, country id error
or
err no device
I located the file "wceusbsh.sys" but still.
After "checking the information on your device" i get the error.
"Error 120, country id error"
How can i solve this problem.
Greg
You're stuck in bootloader. Did you try to upgrade to an other language?
You can try to hard-reset your device 'power & soft-reset' at the same time to boot your magician.
If it doesn't boot, kick it back in bootloader 'camera & power & soft-reset' at the same time for several seconds, till screen turns black & read 'serial v1.00'. When connected to usb it reads 'usb v1.00'
Now get maupgradeut_noid.exe from the ftp. Unzip your shipped-rom file you downloaded from TMO. Put the maupgradeut_noid.exe in the same folder as the unzipped files like maupgradeut.exe, enterbl.exe etc. Then execute maupgradeut_noid.exe instead of maupgradeut.exe this will give the error 120 once more. Just exit & execute it again, now it should proceed upgrading.
Cheers, M
=(
Same problem! Trying to use no id upgrade . I hope it will solve my problem.
P.S. DO NOT upgrade ROM when batt is lo =)

bootloader mode

I tried to make the bootloader mode on my cingular 3125 phone. But It's very difficult. Who can show me ?
I can make a bootloader mode on my Cingular 3125 phone. But I must use
the HTC_Trinity_SIM_CID_Unlock_v1. Once I run file AUTO_Unlock_v1.bat. When update ROM, it transfer to bootloader mode. But on this time, Activesync stop connect to my phone and update to notice error "image file 's corrupted. How 'll I do activesync work always ? Please help me.
Thank !

Activesync disconnect

Activesync 4.5.0 work normal. But I use unlock phone cingular 3125 via activesync.Everything good. But When The tool transfer to update. It disconnect to my phone with error "image file corruptted". How will I keep the connection ?
I make standby and hibernate mode to never (if make so be wrong.How will I do these mode become disable?)
Please assist me about this problem ?

Tricolor Boot Screen when updating problem - Pls Help

Hi there, when I try to update my ROM from the official WinMo5 update that HTC has I get a freeze, disconnect on Active Sync and and a tricolour screen on my handset...no procgress from there. CAn you please assist me in getting past this.
Ive tried most of the 6.1 Roms on this site with the same result. I also had the security pop up and disabled it with HTCustom.
error messages
I get error 246 on active sync when doing the above and the tri color says : IPL SSPL by Dex TRIN100 SPL-1.07.DS AND USB in the white
If you have received connection error 246 while trying to update your ROM, leave your device in bootloader and connected via USB and restart the Rom Update Utility
More info on this site :
http://trinityguides.info/index.php?option=com_frontpage&Itemid=1
Hope this will help you

List of ERRORs, update firmware

I can't post in developer forum yet....
u ERROR [202, 204] : CONNECTION
This error message will appear when the device is not connected to ActiveSync correctly. Make sure you properly connect the device to the PC through ActiveSync before running RUU.
u ERROR [260] : CONNECTION
This error occurs when there is an “open port error” before upgrading the CE ROM image.
Solution: You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again.
u ERROR [206] : MEMORY ALLOCATION
u ERROR [280] : UPDATE ERROR
When you see any of these error messages, close other running programs on the computer and run RUU again.
u ERROR [208] : FILE OPEN
u ERROR [210] : FILE READ
These error messages indicate that RUU lacks certain important files and cannot continue with the update. Please get the complete RUU package again.
u ERROR [212] : FILE CREATE
u ERROR [214] : FILE WRITE
u ERROR [222, 224] : DEVICE NOT RESPONDING
These error messages will appear when remote access control has failed. Check the ActiveSync connection and try running RUU again.
u ERROR [220] : MAIN BATTERY POWER
This error message will appear when the device’s battery power is not sufficient. Although RUU will instruct you to plug in the AC adapter, it still has to make sure that your device has enough power to upgrade the radio. (Even when you plug in the AC adapter, the device is unable to charge the battery when it is upgrading the radio).
u ERROR [238] : FILE READ
This error message may appear when, for some unknown reason, the ROM image on the Mobile Device is corrupt. Download the whole RUU and try again.
u ERROR [240] : FILE OPEN
When this error message appears, check whether the downloaded image is placed in the directory of RUU. If, for some unknown reason, you find that the ROM image is not located in the RUU folder, you have to download the RUU and retry again.
u ERROR [242] : INVALID LANGUAGE
u ERROR [244] : INVALID MODEL ID
u ERROR [294] : INVALID VENDER ID
u ERROR [296] : UPGRADE ONLY
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.
u ERROR [246] : DEVICE NOT RESPONDING
This error message indicates that RUU cannot start the update process. Please contact your service provider for assistance.
u ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
u ERROR [300] : INVALID UPDATE TOOL
This error message will appear when you use the incorrect RUU version to upgrade.
u ERROR [330] : ROM IMAGE ERROR
This error message will appear when you use the incorrect RUU to upgrade and the image file size is larger than the Flash ROM size. In this case, download the correct RUU version to upgrade.
well,thanks man for the sharing
valuable information may be usefull just in case
I always end up with 270 error.

Categories

Resources