Hi
How i can enable the handsfree on and conference functions during a call?
Since I upgraded wm5 to wm6, I can´t use both functions. During a call I touch the menu button but this functions aren´t enabled.
Thanks.
motok1 said:
Hi
How i can enable the handsfree on and conference functions during a call?
Since I upgraded wm5 to wm6, I can´t use both functions. During a call I touch the menu button but this functions aren´t enabled.
Thanks.
Click to expand...
Click to collapse
for your handsfree... do you have a bluetooth headset or other bluetooth speaker phone/mic device paired with your dash and turned on and connected when you are trying to enable hands free?
if not , handsfree will not be available.........speakerphone however should be an option
as far as conference functioni think you have to have 2 calls on the line and then you have to use the join calls option to conference i believe (maybe its still conference?)
Ok, I´ll try, but the handsfree only works with wireless or bluetooth earbuds?
No options for mini usb wired headphones?
Any sugestion for the conference problem?
Thanks
motok1 said:
Ok, I´ll try, but the handsfree only works with wireless or bluetooth earbuds?
No options for mini usb wired headphones?
Any sugestion for the conference problem?
Thanks
Click to expand...
Click to collapse
when using wired earbuds, it should automatically direct the calls to the headphones....assuming you're using the earbuds provided by HTC and read my edited comment above regarding conference issue
So for conference do this...... Call someone, once connected... press right soft key and select hold.... then dial another number and press green talk button to dial.... then after that call is connected....you can then press the right soft key again and you can select conference... which will join the two calls . ......whalah!
pudgedaddy said:
So for conference do this...... Call someone, once connected... press right soft key and select hold.... then dial another number and press green talk button to dial.... then after that call is connected....you can then press the right soft key again and you can select conference... which will join the two calls . ......whalah!
Click to expand...
Click to collapse
Thanks for the answers, but the problems still exits. The problem was after the upgrade to wm6, because my phone was original from T-mobile wm5.
So, the options are there but not highlighted in the menu (I can´t choose it)... or not enabled. Maybe a change in the registry?
Thanks
pudgedaddy said:
So for conference do this...... Call someone, once connected... press right soft key and select hold.... then dial another number and press green talk button to dial.... then after that call is connected....you can then press the right soft key again and you can select conference... which will join the two calls . ......whalah!
Click to expand...
Click to collapse
Thanks for the answers.
The real problem is my version of WM6, it´s not enabled both functions with wired headphones. With the old wm5 from t-mobile, i did´nt had this problem.
My version has WWE, EUK and Spanish lenguages, it´s a little diferent,
Thanks, again.
Related
how can do voice dialer by HBH 300 with my pda2k?
id like to diale a contact nuber by using bletoothheadset
search before posting;
this has been asked billions of times.
YOU CAN'T
Well you sort of can.... depends on your definition of voice dialling.
(a) Make sure voice command recognition software is running (might be MS Voice Command, or Fonix Voice Dial, or Fonix Central, or other). This MIGHT require a button press on your PDA
(b) With headset in ear, press the call button on headset for a period of time longer than single press and shorter than turning it off, this is different for different headsets. You'll have to experiment.
(c) you will hear white noice (buzzing) in your ear. Speak your command, e.g. Call Fred
(d) you will NOT hear confirmation of your command through the headset, that will still come out of the PDA, it's only sending commands from headset.
(e) all being well, and your voice command software having not timed out, your call will now initiate.
(f) when your call is dialling, your BT headset will engage as normal.
I managed to get this working with my Jabra BT200 headset, which is apparently not an officially supported headset with the Blue Angel, so I was well chuffed. I had to rig up one of my buttons to engage the voice dialling software on my PDA as I don't have MS voice command.
So sort of, but not properly!!
Have fun experimenting, if it doesnt work, don't blame me, it's not supposed to work on this phone at all!!
THANK YOU sazoo
great reply !!!!
its work man !!!!
THANK you ((billions)) of time :twisted:
I wonder if such functionality is officially supported with BT headsets supporting A2DP profile (like this one: http://www.itechdynamic.com/html/border22.htm)?
big boss said:
THANK YOU sazoo
great reply !!!!
its work man !!!!
THANK you ((billions)) of time :twisted:
Click to expand...
Click to collapse
Or just use Vito Voice Dialer 3.5 worx great
This MIGHT require a button press on your PDA
Click to expand...
Click to collapse
Hi.
Were you able to do it without pressing a button? Because that defeats the objective of total freedom with bluetooth...
I could do it but never without pressing a button...
Thanks in advance,
Joao Caldeira
Hi.
Were you able to do it without pressing a button?
Click to expand...
Click to collapse
I second that question and if the answer is no, then is there any way to press an assigned button without turning on the device or assign to 1 button the command to turn on the device and run a program (e.g. Vito...)? (My idea was to use the record button, so that i dont need to take it out of my belt-case).
Hiya, I got a BT800 for Christmas from my lovely wife and am having a hell of a time getting it to activate voice dialling!
Having paired it and chosen to use it as the hands free device, I can use it for phone calls that I start from the phone, but the Exec doesn't do anything when I 'tap' the answer button (one beep) or squeeze it(beep, pause, beep).
I've even just restored the original rom (hard-reset, basic install) and it still doesn't do anything...
Did anyone else have this problem? Is there a stage I'm missing out?
Hope someone can help, I've a nasty feeling it's too late to return it to Amazon...
Might be a daft question, but have you added your voice tags (or re-added after hard reset)?
Thanks for the reply, I was never intending to use voice speed dial (preferring voice command by miles) and so didn't record any tags. Even without any, you should still get the app launching and a message that there aren't any tags recorded. My problem was that I wasn't even getting that.
I can't claim to have solved the problem, but at least I no longer have it! I reinstalled the original O2 ext_rom and did a nice clean "Basic" install then put my customised ext_rom back and reset again. Having paired the headset I was able to launch voice speed dial from it, so went ahead and installed voice command, made the registry change to launch VC from the headset and am laughing.
I wish I knew what had caused the problem so I could avoid doing it again! I suspect that it was an attempt to restore my bluetooth registry settings on a rebuild that was the cause... Certainly I didn't try to set it up automatically the second time round and it *did* work, but there are too many variables to be sure.
HTH someone!
The Universal has no NATIVE support for Voice Dial using Voice Command. You have to do the following so it will work via VOICE COMMAND as it has to bypass the Installed Vocie software:
Install Voice Command to the default location.
Fire up a registry editor
Go to: HKEY_LOCAL_MACHINE\SOFTWARE\OEM\VoiceCommand
Modify the string marked "path" from the default \Windows\SDDialer.exe to \Program Files\Voice Command\VoiceCMD.exe
This should now launch Voice Command
Maybe you made a mistake like missing a letter?
If you have done the above and it still doesnt work, then i'm just as lost as you are
sorry, browser problem, message was posted twice
I'm using the BT800 with my Qtek 9000 (Original ROM) and don't have any problems with voice dialing. After pressing the button on the Jabra within a second or 2 the voice dialing application is started, I hear a start sound, speak the name and it automatically starts dialing.
I have installed the latest BT800 firmware (becaus of the international dialing bug) and had not tested this functionality with the original firmware. Which firmware are you using?
MvanIperen said:
I'm using the BT800 with my Qtek 9000 (Original ROM) and don't have any problems with voice dialing. After pressing the button on the Jabra within a second or 2 the voice dialing application is started, I hear a start sound, speak the name and it automatically starts dialing.
I have installed the latest BT800 firmware (becaus of the international dialing bug) and had not tested this functionality with the original firmware. Which firmware are you using?
Click to expand...
Click to collapse
Which button do you have to press to activate the voice dial? The left or the right button under the LCD? Is it Tap or Hold, the button i mean?
@jorgee: 1st post - thanks, that's what I meant earlier when I said I'd done the reg fix and it all worked
2nd post - to activate voice dialling on a UK O2 Exec, you press the 2nd button from the left on the front of the device - next to the camera button.
@ MvanIperen, I'm using the latest BT800 firmware too, when I did a couple of rebuilds, the problem went away and it now behaves as you describe.
@ all, thanks for the replies! It was just me after all! Mental note: Mess with the registry at your peril!
[quote="this_mike
2nd post - to activate voice dialling on a UK O2 Exec, you press the 2nd button from the left on the front of the device - next to the camera button.
[/quote]
I meant is there anyway to activate voice dial from the headset? Can i only activate it by pressing the voice command button? I mean lets say my phone's in my drawer and i have the BT800, do i have to pull out the phone to be able to use the voice dial?
Jorgee said:
I meant is there anyway to activate voice dial from the headset? Can i only activate it by pressing the voice command button? I mean lets say my phone's in my drawer and i have the BT800, do i have to pull out the phone to be able to use the voice dial?
Click to expand...
Click to collapse
Maybe I misunderstand what you're asking.
You posted the registry change to make this work higher up the page.
Pressing the answer button on the headset does fire up Voice Command but only if the display is open or in portrait mode. If it's closed in your pocket protecting the screen then it won't work
I've never installed voice command, i was talking about the built in voice dial application. If the QTEK is in my pocket, and i want to call someone, which button on the headset/BT800 do i press to activate voice dial? And is it push or push and hold? Do i ghet any kind of audible warning telling me i can start speaking the voice tag?
I hope this time i am a bit clearer, sorry for the previous confusing post.
Jorgee said:
I've never installed voice command, i was talking about the built in voice dial application. If the QTEK is in my pocket, and i want to call someone, which button on the headset/BT800 do i press to activate voice dial? And is it push or push and hold? Do i ghet any kind of audible warning telling me i can start speaking the voice tag?
I hope this time i am a bit clearer, sorry for the previous confusing post.
Click to expand...
Click to collapse
On the BT800:
- To activate voice dialling (whether using MS Voice Command or the 'standard' voice dialling app) using a BT800 headset, press briefly the button nearest the headset microphone.
- To redial from the headset the last number dialled, press and HOLD the button nearest the headset microphone.
This works for me whatever situation the Exec is in: open, closed, portrait, landscape. I'm using the default voice-dialling software, not the MS one. Hope this helps.
Thanks SiliconS,
That was the answer i was looking for, sorry i had to bother you guys instead of reading the manual as my manual is in Spanish and i am only a beginner-intermediate level reader.
Again THANKS!!!! Very appreciated
Are any of you folks running WM2003SE? See, I was able to make that registry change and do a soft reset and have Voice Command working through the BT headset on my old machine, but it was running WM2003 (not the second edition version). From what I have read, SE doesn't seem to like that registry change, as when you make it, all that will happen is the connection opens when you tap the button on the HS, but the ability to use VC is not there.
I know there must be some way to do this. Any opinions or suggestions would be fab!
Thanks much!
How to change the Speech Dial to something different (handsfree set -> green button)
Hi!
I own a MDAcIII with the O2 WM6-Update installed on it. When I press the green Button of my Parrot Evo CK 3000 (handsfree set), the Speech Dial appears. I don't want to use the speech dial, I want that the list of last dialed Numbers appears. How can I change this Feature?
Thanks!
KobiP
Hi!
Not sure if this suggestion will help or not, hope it does. I have and o2 orbit with WM6 (B&B v3.7 cause Tom Codon Rocks ) and a Jabra headset when i press the button once on the headset it goes to the speech dial appears but if i double click it (quickly) it ether calls last number dialled or opens the dial pad.
Wooley said:
Hi!
Not sure if this suggestion will help or not, hope it does. I have and o2 orbit with WM6 (B&B v3.7 cause Tom Codon Rocks ) and a Jabra headset when i press the button once on the headset it goes to the speech dial appears but if i double click it (quickly) it ether calls last number dialled or opens the dial pad.
Click to expand...
Click to collapse
Sorry, that doesn't happen in combination with the Parrot Handsfree. Double press is the same as once, speech dial. But if I press the green button longer, I redial.
Nevertheless: Thank you for your hint! Thumb up
Hi Guys,
Does anyone have a solution for the problem that the call button on bluetooth headsets won't work anymore with the TP2?
I use it in combination with Voice Command which worked flawlessly with the Touch Diamond, it's also been set to the same (and only) hardware key as the diamond but it won't work on the headset!?
It works fine when you press and hold the call button on the phone though...?
thanks!
jan
redsunpost said:
Hi Guys,
[...]
It works fine when you press and hold the call button though...?
[...]
Click to expand...
Click to collapse
When you say it works fine, do you mean through the BT headset, or just through the speakerphone?
P.S. I had an opportunity to talk with someone at Microsoft, and the response I received was "it's a known problem" and "wait for the next update or next version".
Alas...
i've edited it..
Strange problem cause the diamond had the same windows mobile version?
redsunpost said:
i've edited it..
Strange problem cause the diamond had the same windows mobile version?
Click to expand...
Click to collapse
It's nothing to do with the WinMo version, it's a different BT Stack.
I have been playing with it today and will post an update in the tweaks thread once I have it patched.
Cheers,
Beasty
Its not the BT Connection with a headset in general. That function works fine. I've tested it with my bt headset. Pressing the button I can accept the call and/or redial.
The problem lies within Voice Command itself. Once installed it gets assigned to the one and only hardware button configurable (hold call button for 3 seconds). The problem with that is when I do that with my BT headsets (normal and motorcycle one). They get powered off by pressing them for 3 seconds (same button). xD
I disabled Voice Command though due to the ringtone volume bug. Every 2 seconds the ringtone gets low for an announcement that you don't hear. Still waiting for a proper fix without all the work of replacing files.
I was looking for the original voice dialing function. But it really isn't there on the TP2. Voice Command is much better though. But damn that bug.
ChriX84 said:
Its not the BT Connection with a headset in general. That function works fine. I've tested it with my bt headset. Pressing the button I can accept the call and/or redial.
The problem lies within Voice Command itself. Once installed it gets assigned to the one and only hardware button configurable (hold call button for 3 seconds). The problem with that is when I do that with my BT headsets (normal and motorcycle one). They get powered off by pressing them for 3 seconds (same button). xD
I disabled Voice Command though due to the ringtone volume bug. Every 2 seconds the ringtone gets low for an announcement that you don't hear. Still waiting for a proper fix without all the work of replacing files.
I was looking for the original voice dialing function. But it really isn't there on the TP2. Voice Command is much better though. But damn that bug.
Click to expand...
Click to collapse
Sorry to disappoint you chrix, but the same hardware button (also hold) is used with the Touch Diamond.
Like I said they both look the same but with the TP2 it doesn't work, i'll be looking out for your patch beasty!
Another suffering TP2 user!
Hi guys,
I am also suffering with this issue as well. I did try and see if an old registry hack worked (changing HKLM\Software\OEM\VoiceCommand path=\Program Files\Voice Command\VoiceCmd.exe) but it didn't unfortunately. As previously pointed out in this forum, I think that this issue is more down to the fact that HTC seemed to have replaced the Bluetooth stack with their own proprietary version which isn't bad by all accounts, but does seem to lack this functionality. I might try and contact them to see if there's an update to resolve this but if someone does manage to create a patch for it, I'm sure there's a number of us who would be interested!
Cheers,
Barry
I installed voice command as well.
I'd already used the send button to put my lock on so it gave me another button (see attached).
Any body Know where the button is.
Please need help to activate CSVD over BT in TP2,
I can end the call over BT, redial, but I can't start voice dial.
When I press BT button to start voice dialing nothing happens. Voice dialing enable only if I press key on the phone. Thank you.
cybersergey said:
Please need help to activate CSVD over BT in TP2,
I can end the call over BT, redial, but I can't start voice dial.
When I press BT button to start voice dialing nothing happens. Voice dialing enable only if I press key on the phone. Thank you.
Click to expand...
Click to collapse
This is an issue with certain roms on TP2 ... does not work via BT headset on MVC either on my T7381... just off the phone to HTC tech (long running saga) and he advised wait for new rom update .... HTC tested as working on their model TP2 but not on my 1.19.841.3 rom