Related
I follow instruction in http://forum.xda-developers.com/showthread.php?t=313486 but after hardreset.
My p800w is stuck in T-Mobile logo and version number. It can't continue booting up to windows mobile.
Question: How to flash ROM without ActiveSync?
How to recovery my Artemis?
Welcome any advice,
Thanks in advance.
Yea me to, mine is now a brick after that upgrade? No active sync connection possible and all I get now is the blue O2 start screen after the hard reset with the red writing and numbers in the top left hand corner..
Phone is an UK XDA Orbit
IPL 1.25.0001
SPL 1.11.0000
GSM 02.67.90
OS 3.4.0.0
HELP!!!!!!!
yeah, I had the same problem and have created a thread for it already. unfortunately I got no useful replies, and it seems that I am stuck waiting for an official o2 ROM so that I can recover my Orbit.
It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???
motomob said:
It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???
Click to expand...
Click to collapse
I read in here that you hold the voice button and soft reset.
Decaf said:
I read in here that you hold the voice button and soft reset.
Click to expand...
Click to collapse
Correct and use mtty
Already see in the forum ....
Thanks guys and apologies for the spelling..I ran the Artemis_USPL before I tried upgrading to WM6 and again have been able to run it after with my new brick now with the phone in bootloader mode but still when I try and run the german ROM update a) it will only work with the german file which freezes @ 3%? This seems to be a known problem reading around and b )when I replace it with the smaller ROM file, 54MB the german one is 66MB, I originally tried to use it doesn't read the ROM file or the update utility doesn't want to read it. I reckon I might be able to get it back if I can get one of the ROM update utilities to read a good ROm file and send it to the phone.
I can;t find this MTTY program to sniff the USB port and return the code of if the USPL util wokred as I think that could be key to all of this.
Can anyone post a quick how to here for
1) install MTTY from somewhere
2) what command to run agaist the phoen to see if the USPL util worked and what values I should be looking for
3) another WM6 ROM version (that the update utils can read) download location I can download from to try and send to the phone using the German update util
Not asking for much am I but I desperately need my phone back WM5 or 6 in the next day or so so really can't send it off.
Thanks
Error message I recive at the 3% stage when using the German ROM and english update util.
use the file attach and read that :
http://forum.xda-developers.com/showthread.php?t=285112
Thanks but I'm not that cleud up on what commands I'm meant to be sending. It works in Bootloader mode I ge a response from the phone by send it a command. But even if I get a response telling me what the CID status is its not much help as I think ti shoudl have tekane BEBEs ROM by now as I've got the german ROMUpdateUtility sending that 54,272KB file to the phone but it stops after 3%. What are my options?
motomob said:
But even if I get a response telling me what the CID status is its not much help as I think
Click to expand...
Click to collapse
That's right. On older models MTTY was quite useful, but not on the Artemis. You cannot use it to read the CID status anyway. If you are not sure about the status, run the USPL tool, just to make sure.
I've already re run the USPL ROMUpdateUtility and it completes 100% okay in bootloader mode. But after I hard reset and then try and flash the WM6 BEBE ROM or any ROM German etc back onto it it either fails with the error code I posted up earlier or gets to 3% and fails.
What are my options at this stage? Does anyone have a link to another ROM I can try like the original WM5 O2 ROM or any other WM6 ROm that might work. I'm willing to give them all a try as it's just a useless phone right now and I haven;t sent it off as 1) I need it before the weekend and 2) As I can flash some ROMs with the USPL and others have done this no problem I really feel there must be a solution as I can still falsh the phone.
What can I say RTFM... I did it all right and I didn't have a brick, I missed out one small detail... loading on the ROM with the extended ROM. All now running and it does seem a little faster than WM5.
Thank you to all those that tried to help out. To the others that are still having probs.. Don't try and run the update in the middle of a busy day in the office whilst trying to manage 100 other things meaning you are probably missing out a line like me...
One question though how do I get back my O2 power and storage meters on the today screen back as I liked them and the WiFi seems to have a bug where when it is enabled and you click on the WiFi symbol up the top it only allows you to switch it on, when it is already on.. so you have to open up the COMM manager to switch it off.
So how did you fix it exactly? I have read this thread thoroughly and can't find out what you did!
ERROR[206] occurs while trying to update ROM to WM6
While tring to update ROM to WM6 on O2 XDA Orbit i encounter ERROR[206].
I wanted to attach the screen shot but dont know how to do that, but anyway what i am doing is i attached my pda to my pc via activesync using supplied usb cord. Everything goes well till i reach a screen where it says "You are now ready to update your ROM image...." and once i click next a progress bar apperas and my pda shuts and activesync exit's automatically and my pda tries to restart with RBG band and some text:RUU, IPL 1.25.0001, SPL 1.25.0000 and USB. And thats it after few seconds or a min i get the ERROR[206] and my pda hangs.
I dont know why Activesysn shutsdown ???
Just an additional in i want to tell that without installing activesync i am not able to connect/pair my pda with my pc. So do i need to install the drivers and then try or it doen't matter cause once i install Active sync i can connect the device.
Please help me with this....
Thanks
unable to load bootloader!!!!!!!!!!!!
HELP!!!!!!!!
I have HTC3300, tried to update rom, now its bricked. I tried to start bootloader by pressing the voicebutton and softreset but loads in t-mobile screen and hangs, im unable to start the bootloader.
Is this end of story or are there any other options to get the bootloader to start????
please help
Bootloader
I had a problem with my phone loaded touch flow 4 and cid unlocking, everything was fine then after a while it froze at boot up.
I look put the battery and did a hard reset, put it into bootloadeder mode, reflashed with a t-mobile rom does not need to be cid unlocked to do that.
Once origonal rom was working, cid unlock again, flashed back to touchflow 4.0 - sorted
Where did you got an tmobile rom from can you tell me. Mine is also freezing on booting almost once every day or so after I've upgraded to 4.0
I was in the middle of upgrading my version of WM6 and i got unplugged and now it wont resume and the phone is stuck at the loading screen that says "HTC" mobile.htc.com
what the heck do i do? it wont budge.. it wont sync with active sync, it wont resume.. i'm flipping out.
did you try get your phone in the tri color bootloader screen and then running the Hard SPL program again?
god, I'm gonna admit, I have no idea what any of that stuff is. I know the tricolor screen, I dont know what an SPL is.. a friend of mine usually sends me the upgrades for my programs and i just follow his instructions, but as i was loading the new version it got unplugged and when i tried to follow the restore options it wouldnt restore the upgrade.. so I've learned the term is bricking.
Activesync won't reconnect the phone.. it tries, then doesnt recognize the device.. so even if i try to downgrade to 1.04, it wont work because it wont sync with the damn computer.. I hard reset, i soft reset, i got it to the tricolor screen, i tried all the stuff in the hermes upgrade problems thread, but i dont know wtf i'm doing. the file mtty.exe wont work.. it just freezes at whatever screen i happen to get it to, be it the tricolor or the HTC screen.
please, someone help me out.. I apologize in advance for not being as savvy as everyone else, but I need some advice here.
Go the tri colour screen
press both soft buttons (the ones that interact with the screen) and insert the stylus and reset.
from here you can make an hard reset. Whenever my phone hangs (or whatever) I use this way BUT i use the cancel button (X) and the phone simply restarts fine
Did u hard SPL your device?
Costanza said:
press both soft buttons (the ones that interact with the screen) and insert the stylus and reset.
from here you can make an hard reset. Whenever my phone hangs (or whatever) I use this way BUT i use the cancel button (X) and the phone simply restarts fine
Click to expand...
Click to collapse
I hard reset, I soft reset, it freezes either way. The only way the computer recognizes the phone is when I get the tricolor screen but active sync wont connect to FINISH loading the upgrade.
antonlim1999 said:
Did u hard SPL your device?
Click to expand...
Click to collapse
I cant because it wont connect to activesync to install anything else.. i cant dongrade, upgrade, nothing! i cant get to version 1.04 from the 1.06 im running because activesync wont recognize my phone.
I think antonlim1999 mean, did you hard-spl before you even upgrade to wm06 or not ?
sg10 said:
I think antonlim1999 mean, did you hard-spl before you even upgrade to wm06 or not ?
Click to expand...
Click to collapse
I already had wm6, i was just getting a better version that didnt have as many bugs.. I began loading it, it got to 45%, then the cat knocked the cable out and it got messed up.. I dont believe it was hard-spl beforehand.. im gonna go with no.
Could you try to SPL in the tri colour mode (as you have contact between the unit and the PC)?
Link below has all (almost) info
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
A warning to those with an aversion to reading
This is a warning to those who don't really know what they're doing. Upgrading a ROM on a WinMo device is something that should only be done when you know what you're doing.
Hope your device can upgrade well, but please, take the time to actually read the wiki and forum before upgrading again, for your own wallets sake.
hiddenconcepts said:
I was in the middle of upgrading my version of WM6 and i got unplugged and now it wont resume and the phone is stuck at the loading screen that says "HTC" mobile.htc.com
what the heck do i do? it wont budge.. it wont sync with active sync, it wont resume.. i'm flipping out.
Click to expand...
Click to collapse
You are not even in the right forum, you'll get better help elsewhere.
Start reading here: http://forum.xda-developers.com/showthread.php?t=286755
Hard SPL thread: http://forum.xda-developers.com/showthread.php?t=296722
philjohn said:
This is a warning to those who don't really know what they're doing. Upgrading a ROM on a WinMo device is something that should only be done when you know what you're doing.
Hope your device can upgrade well, but please, take the time to actually read the wiki and forum before upgrading again, for your own wallets sake.
Click to expand...
Click to collapse
thanks, but I've upgraded before to other versions without a problem and I know that pulling the plug out is a bad idea.. the cat jumped up and ripped it out causing it to brick.
What all the smart arses on this site should be telling you is that you don't need activesync to run the upgrade - it will work just fine from the tri-colour screen.
First off, when you get your phone into the tri-colour screen, check the SPL version - if it isn't 2.10 olipro, the first thing you need to do is read the vanx guide's (link in my sig) and get hard SPL 2.10 olipro on there ASAP - this will prevent you from bricking your phone.
If it is already 2.10 olipro, then breathe a sigh of relief as everthing is OK - just put it into the tri-colour screen and run the upgrade again - it should start again with out a problem.
Cheers,
Smiffy.
Hiya XDA
I've been trying all evening to get any HardSPL onto my Diamond without success, everytime I try I get to 0% and after a few minutes "error [260] connection" and the phone keeps its' black screen until I soft-reset it.
Can anyone help me get a hardspl onto my phone? I would really like to try WM6.5. I've read many SPL-guides already, so you don't have to point me to them
(even that on modmydiamond.info)
Thanks in advance!
esset said:
Hiya XDA
I've been trying all evening to get any HardSPL onto my Diamond without success, everytime I try I get to 0% and after a few minutes "error [260] connection" and the phone keeps its' black screen until I soft-reset it.
Can anyone help me get a hardspl onto my phone? I would really like to try WM6.5. I've read many SPL-guides already, so you don't have to point me to them
(even that on modmydiamond.info)
Thanks in advance!
Click to expand...
Click to collapse
Here's the Tutorial and here's the Troubleshooter. They're both stickies. Please search and read before posting.
Thanks for the quick response, but as I said. I've read all stickies and guides, and it's still stuck at 0%.
esset said:
Thanks for the quick response, but as I said. I've read all stickies and guides, and it's still stuck at 0%.
Click to expand...
Click to collapse
Did you let your device sync with Activesync/Windows Mobile Device Center?
Try recreating the sync pairing.
Try uninstalling the device from PC's Device Manager and reinstalling it and then try recreating the sync partnership.
Try another USB port.
Yes, yes, yes and yes. I even tried doing it on my laptop.
Edit: I even tried flashing down to 1.93 with HTCs official stuff, no success there either
esset said:
Yes, yes, yes and yes. I even tried doing it on my laptop.
Edit: I even tried flashing down to 1.93 with HTCs official stuff, no success there either
Click to expand...
Click to collapse
Another USB cable?
Try manually entering bootloader and connect to PC. The label should say USB not Serial and try from there.
esset,
May I ask what branding/model of the Diamond you own?
I own a pure AT&T model just purchased a week or two ago. And, so far I've also had almost zero luck flashing it. I'm moving from an AT&T Tilt which I've flashed so many times, the USB port is starting to wear down. I've also got a lot of experience with many small computing devices with all types of weird programming and flashing routines, so I'm not a newbie. But the AT&T Fuze just seems to be locked in a way that has yet to be covered by the good XDA folks here. Heck, I can't even dump the shipped ROM off the device to send it here for checking out by the developers. All I've been able to do is flash an odd 1.90 HardSPL that seems to have locked the phone even tighter than before. YUCK!
If you're in this same scenario, I'd suggest patience. Eventually someone with enough knowledge of these devices will be able to help out. It is frustrating though, after flashing the other phone so many times with so many different configurations to be held back on the new one.
tnyynt said:
Try manually entering bootloader and connect to PC. The label should say USB not Serial and try from there.
Click to expand...
Click to collapse
You might find this odd. The down-volume + back arrow key combo doesn't seem to work with some of the new versions of the Diamond. I've tried on two of them, and neither respond to this key combo at startup.
Many times entering the bootloader is not a problem though. The routine does cause the phone to go there. And, I can get it there by other means. Just not via the boot up sequence. This tells me there is something very different about these models....
I tried starting and flashing directly from the bootloader (showing USB), and the phone got to show a percentage field (the one when you are flashing) but same here, is constantly at 0% until the flashing utility times out and tells me to reboot my phone and guides me through steps if it has been semi-bricked (bootloader is the volume down + softreset, right?)
I bought my phone in the first shipment to Sweden, it's not locked to any company, bought it without subscription
Else I just flashed it up to latest ROM from htc.com (still no success with HardSPL ) to 2.03.413.2 SVE (02/06/09)
Radio: 1.09.25.23
Version: 52.51.25.26H
ninjaedit: (In the four-colored bootloader thing it says DIAM100 64M SPL-2.03.0000 MicroP-Diam (LED) v11)
Tell me if you need any other info :]
Here's another indication that the new phones are different. I've copied a DIAMIMG.nbh file to both a flash card inside the phone, and to it's internal memory. (sorry, but the thread on that location is confusing on what memory. I assume like most phones of the past that it's supposed to be the flash card, but "internal memory" is not a flash card.) But, the loader screen always responds with "no image file" when it's called up. So, is there a different name expected now?
put manual hardspl into your device, and click to it from your device..
zerocool81 said:
put manual hardspl into your device, and click to it from your device..
Click to expand...
Click to collapse
Tried that with every Hard-SPL linked to from this thread: http://forum.xda-developers.com/showthread.php?t=415191
Didn't work
Something's changed.
zerocool81 said:
put manual hardspl into your device, and click to it from your device..
Click to expand...
Click to collapse
Hi uhm, was that answer aimed for me or to scottwilkins?
If it was for me, is it possible to flash the mobile directly from the memory-card (or internal flash card)? Else if you mean the "manual make-the-screen-black-and-go-to-bootloader" my screen just goes blank, as when you do it with the RUU, and just stops there. Also seems like it looses the connection via USB doing so too. And flashing through the bootloader directly (volume down at softreset) shows the progressbar on the phone, but steadily at 0% (when trying to flash).
search and download
a) SDA_ApplicationUnlock.exe (Desktopprogram)
b) EnterBootloader.exe (ATTENTION: it must be that for diamond, normaly find by flashing-tools)
connect with active sync and copy EnterBootloader.exe to pda-root.
start SDA_ApplicationUnlock.exe on desktop and follow all but reset (DONT RESET)
start EnterBootloader.exe on pda
if bootloader-Mode and USB-Label than start flashing
wait for response
scottwilkins said:
Tried that with every Hard-SPL linked to from this thread: http://forum.xda-developers.com/showthread.php?t=415191
Didn't work
Something's changed.
Click to expand...
Click to collapse
try this.. put this file into internal storage and lounch this from ppc
http://rapidshare.com/files/207721836/SSPL-Manual.rar
okokur said:
search and download
a) SDA_ApplicationUnlock.exe (Desktopprogram)
b) EnterBootloader.exe (ATTENTION: it must be that for diamond, normaly find by flashing-tools)
connect with active sync and copy EnterBootloader.exe to pda-root.
start SDA_ApplicationUnlock.exe on desktop and follow all but reset (DONT RESET)
start EnterBootloader.exe on pda
if bootloader-Mode and USB-Label than start flashing
wait for response
Click to expand...
Click to collapse
I tried what you suggested, I successfully unlocked the phone (and did Not reboot it). Ran the bootloader; and the screen just went black, as usually, and nothing more happens
zerocool81 said:
try this.. put this file into internal storage and lounch this from ppc
http://rapidshare.com/files/207721836/SSPL-Manual.rar
Click to expand...
Click to collapse
That program makes the Fuze screen just turn black and do nothing. Cool, huh
Seems that the newer stock ROMS might be blocking something... hmmmm....
Well, crap!
I just figure out where my whole problem is...
The Fuze (my phone) = The Raphael
NOT the Diamond.
I just scrolled down the forum list, saw a phone that looked like mine and went there. DOH!
I feel like a total dumb-ass.
If I'd scrolled just a bit farther down the XDA forum, then I'd seen the Raphael phone.
Holy Cow! Go ahead, say it, I deserve it...
Thanks for all the help otherwise. It was a learning experience for me....
esset said:
I tried what you suggested, I successfully unlocked the phone (and did Not reboot it). Ran the bootloader; and the screen just went black, as usually, and nothing more happens
Click to expand...
Click to collapse
hi,
i think, you have the wrong bootloader.
i find this and try it by me self. this brings your fone definitly to bootloader.
than you can start manualy the hard spl by normal description way.
http://rapidshare.com/files/208123046/EnterBootloader.exe.html
okokur said:
hi,
i think, you have the wrong bootloader.
i find this and try it by me self. this brings your fone definitly to bootloader.
than you can start manualy the hard spl by normal description way.
http://rapidshare.com/files/208123046/EnterBootloader.exe.html
Click to expand...
Click to collapse
Thanks, but that file takes me into the bootloader, and when I start flashing the percentage is still at 0% until the software times out. Same as before, just the usual "going-into-the-bootloader".
Hello,
afther an update on my p3600 with an error.
I have only the bootscreen of the rom.
I cant flash any new rom , every time i have connection errors.
is there any chance to correkt the problem or to delet the phone completly?
A Hardreset doesn´t bring anything.
Please help me i cant do anything with my p3600.
take a look:
http://forum.xda-developers.com/showthread.php?t=572747
i read the thread,
but i have tested to update the hard spl but it doesn´t work.
The update software always told me that there is an connection error.
But when i want to install the rom 6.1 manila 2g the software found an connection and start to update but when the software is at 1% the update software told me that the rom is corrupt
This is the reason you should always install HardSPL BEFORE you start flashing any roms at all.
Once you have bricked it, then it is too late to put HardSPL on there.
The whole point of HardSPL is to ensure that you will always be able to get a connection to the device even if you have a broken rom on there.
If the phone is bricked, with no HardSPL on there, your only remaining option would be to try using an unbricking exploit procedure like this:
HTC Trinity Stack Overflow exploit - how to unbrick any Trinity stuck in bootloader!!
^^^ Sorry I have never had to do this myself and have no experience or advice on how to use that exploit utility ... hopefully there is enough help in that thread to get you going again.
Good luck.
EDIT: I thought I'd better just check you do realise that you can get the Tri-colour SPL screen up manually by holding down POWER + CAMERA buttons and 1sec press of STYLUS RESET button. Quickly reading through that splxploit thread I was disturbed to see just how many people didn't even know who to do that
Maybe it's just my paranoia from owning an "i" model but I have never done a single rom flash without first using that 3 button trick to get into SPL screen.
praefke1986 said:
...But when i want to install the rom 6.1 manila 2g the software found an connection and start to update but when the software is at 1% the update software told me that the rom is corrupt
Click to expand...
Click to collapse
Try flashing the Stock ROM that came with your phone. It may get you going again. Can be downloaded from the HTC website.
Hi everyone well I'm new to the flashing and dont want to jump any steps as this could possible brick my phone...
I've been having some problems with flashing as i cant find a step by step to flashing my HTC TP2. I've managed to do the RhodiumW Hard-SPL package but after trying to flash to some custom RUU's the installation seems to go fine its not until the phone first boots up, that's when the phone just hangs on the HTC splash screen
From there i cant do anything other then boot up to the tricolor bootloader screen and re-install the original 2.04.651.4 update!
can someone tell me what im missing to be able to flash my HTC correctly, or at least point me in the right direction?
Thank you in advance!!!
step 1
http://member.america.htc.com/download/RomCode/HTC Touch Pro2 (Sprint)/HTC Touch PRO2 MR1.exe
step 2
http://rhodiumw.htc-unlocks.com/hard-spl.php
step 3
http://www.mightyrom.com/mightyrom/touch-pro-2/
Hey Tommy many thanks for the post. I just upgraded my phone and peeling through the information overload, however you direct link does not work for step 1. I want to make sure that I am running the correct piece of software that you recommending. Could you please list the title for that file?
Nevermind I was able to find it via a mirror site.
Back into lurker status for now
Thanks
alright so i was able to install they mightyrom on my phone that went well my phone didnt freeze and everything started the way it should have.
but does that mean i can now flash my phone to other for example "leo cell" or Bxsteez Rhodium" if not how do i get to that point cuz when ever i flas them to they just freese on the white splash screen with the HTC logo in green letters!!
Thanks!
If you have installed Hard SPL then use the sd card method.
1. Format the sd card FAT32 ( they come FAT default) and copy the rom's .nbh file onto it. Rename to Rhodimg.nbh .
2. Insert sd card back into powered off Rhodium. Go into bootloader by pushing down volume and power.
3. If you did it properly and Hard SPL is on your phone then it should say to press power to update os...
If you aren't sure if you have Hard SPL then go to bootloader without the sd card in there, it should say SPL - 0.85.Olinex if you have Hard SPL, anything else won't register the flash file.
Cheers...
OK I was able to update to Winmo 6.5 with no issues....but here is my questions with regards to the Rhodium_W Hard-SPL
I was attempting to run it and it never gets pass 0%...In reading the details of the install instructions it reads
"the device needs to be connected to Activesync or WMDC via USB cable. and it must not be in Flight/Airplane mode (i.e. the phone part should be on).
3) internet access is required as the program checks online for updates and for the license."
Click to expand...
Click to collapse
I have yet to activate my phone with Sprint could this be my error that I need to active my phone? I wanted to have the phone flashed and customized before activating.
signalsoldier said:
OK I was able to update to Winmo 6.5 with no issues....but here is my questions with regards to the Rhodium_W Hard-SPL
I was attempting to run it and it never gets pass 0%...In reading the details of the install instructions it reads
I have yet to activate my phone with Sprint could this be my error that I need to active my phone? I wanted to have the phone flashed and customized before activating.
Click to expand...
Click to collapse
I think you should ask this in the hard spl thread in the cmda section...That is the place for those questions Assuming that you have a cdma phone because you did not mention it. Otherwise check the hard spl thread in the gsm section.
Heading that way thanks for the directions mate!
Alright so ive been able to flash my rom to my first custom rom by energy which i like very much, although still a noob, i want to flash it to a different rom
What is the best way to flash to a different rom with out leaving any files behind that would affect the new rom?!
do i have to do a hard reset or something that would clear my phone from any old files?!
htcru7 said:
Alright so ive been able to flash my rom to my first custom rom by energy which i like very much, although still a noob, i want to flash it to a different rom
What is the best way to flash to a different rom with out leaving any files behind that would affect the new rom?!
do i have to do a hard reset or something that would clear my phone from any old files?!
Click to expand...
Click to collapse
Just flash away
LOL alright thanks i guess im just paranoid but thanks i'll "flash away"
Lock
When you start Rhodium_CDMA_HardSPL_V1_10R3_100HSPL stoppers on 0%.
I removed the firmware via mtty 1.42 entering the command: task 28 \ task 29. Ie fully formatnul system. This is often applied to remove the lock on the HTC 6800. At this time nothing worked. Under bootloger any firmware stoppers on 0%. Besides, even the official RUU_Rhodium_W_S2_Sprint_WWE_2.04.651.4_RS_2.32.00WF_NV_SPCS_2.20_0224_PRL60660_S
hip
and HTC Touch PRO2 MR1 from the official portal hangs at 1%, then is restarted Device, and as expected if there is no OSes lit logo HTC ...
What should I do?? If GSM is blocked, how do I remove it to flash?
Ps Is it possible to disable the lock on the firmware via mtty
1.42??
Thank you very much for your answer!
Scream-krg said:
When you start Rhodium_CDMA_HardSPL_V1_10R3_100HSPL stoppers on 0%.
I removed the firmware via mtty 1.42 entering the command: task 28 \ task 29. Ie fully formatnul system. This is often applied to remove the lock on the HTC 6800. At this time nothing worked. Under bootloger any firmware stoppers on 0%. Besides, even the official RUU_Rhodium_W_S2_Sprint_WWE_2.04.651.4_RS_2.32.00WF_NV_SPCS_2.20_0224_PRL60660_S
hip
and HTC Touch PRO2 MR1 from the official portal hangs at 1%, then is restarted Device, and as expected if there is no OSes lit logo HTC ...
What should I do?? If GSM is blocked, how do I remove it to flash?
Ps Is it possible to disable the lock on the firmware via mtty
1.42??
Thank you very much for your answer!
Click to expand...
Click to collapse
the Hard-SPL will only work if you booted windows mobile. you have to sync the phone in windows mobile to the PC.
is there other way to get through in hard spl because i dont have any account for example, paypal...... http://media.xda-developers.com/images/icons/icon9.gif
chrisjavier666 said:
is there other way to get through in hard spl because i dont have any account for example, paypal......
Click to expand...
Click to collapse
Hard SPL is free for non-commercial users.
my tp2 is bricked
i tried to upgrade my htc touch pro 2's rom. i received error 226 and anytime i switch it on, it gets to the tricolor boot and displays a lot of info and says try again. Can anyone please help me?
nastyrock said:
i tried to upgrade my htc touch pro 2's rom. i received error 226 and anytime i switch it on, it gets to the tricolor boot and displays a lot of info and says try again. Can anyone please help me?
Click to expand...
Click to collapse
Did you try flashing the stock ROM? It's always a good idea to try that if you think there's no hope. It flashes everything.
Also, did you try task29?