Related
Hi Guys,
I have been playing around with versions of BB and WM and now I think I have crashed it! The last version installed was 3.7, and it was switching on, but now when I did a re-set, the HTC Screen loaded, but the phone has been stuck on the Windows Mobile Screen for the last hour (I have tried loading without the SD card as the last thing I did was to install TomTom). Obviously I have no ActiveSync connection therefore i cannot flash the rom to the official WM6 Uprade.
Any ideas what todo now!.
Thanks
Hello over there,
I had the same problem with B&B 4. I think you have to hardreset your phone.
Hi, Thanks for the Reply, I just got the XDA so not quite sure how to do the Hardreset! Cheers
I managed to find it! but its still not working! its just the same as before!
it took a few trys but all ok now!!! thanks!
I have this problem too
I have this problem too,
WM6 Dopod P800w offiicial rom
Is stuck on Welcome screen WM screen, i had already HR for three times. for this problem
Very mad...
Ok, PC is fine, close any running programs. Hermes has stock WM5 with some programs added. Only reg tweaks are PTT and removed 3G animation at start.
Device syncs normally every day and both Work and Home.
When I follow all the directions, run the Updater - The PPC gets the Color Bars as the Updater is trying to read it....then AS (V4.5) disconnects and closes. (gone from taskbar) I can soft reset the device, reopen AS, they sync just fine. At this point I have the updater do the next, it pulls up the Current ROM info and says it will upgrade to the new one. I select next, and it starts.....and AS closes again. After a minute the upgrade app says it lost connection. (duh!)
Any ideas why?
I'm not a stranger to upgrading roms on PPC's, have several that have both been updated a number of times. No issues, though that several AS versions earlier.
I've given thought to Hard Reseting the device, but I'm wondering if its more AS's fault.
Any and all input much appreciated!
Thank You!
JETninja said:
Ok, PC is fine, close any running programs. Hermes has stock WM5 with some programs added. Only reg tweaks are PTT and removed 3G animation at start.
Device syncs normally every day and both Work and Home.
When I follow all the directions, run the Updater - The PPC gets the Color Bars as the Updater is trying to read it....then AS (V4.5) disconnects and closes. (gone from taskbar) I can soft reset the device, reopen AS, they sync just fine. At this point I have the updater do the next, it pulls up the Current ROM info and says it will upgrade to the new one. I select next, and it starts.....and AS closes again. After a minute the upgrade app says it lost connection. (duh!)
Any ideas why?
I'm not a stranger to upgrading roms on PPC's, have several that have both been updated a number of times. No issues, though that several AS versions earlier.
I've given thought to Hard Reseting the device, but I'm wondering if its more AS's fault.
Any and all input much appreciated!
Thank You!
Click to expand...
Click to collapse
Are you following the directions at THIS GUIDE . What ROM are you trying to put on there? Did you CID unlock the device? Are you running Vista? Do you have .NET 2.0 or 3.0 version?
That should be enough questions to get us started.
Did you read my title? This is the stock ATT WM6 that came out yesterday. No need to unlock the phone, it is a 1 week old ATT 8525 with the stock ATT WM5 Rom on it.....
Windows XP SP2+ PC.
If it's the rom RUU_Hermes_CINGULAR_WWE_3.62.502.3_6275_1.54.07.00_108_UOOS_SVN05_Ship maybe it had some problems because if you go to the official release site http://www.htcamerica.net/support/8525/software-downloads.html they are still showing the WM5 rom for download.
There may have been a problem with the release and they pulled it back for some reason. Just a thought and not much help I'm afraid.
Yes thats it. When it ID's my current Rom and what it will upgrade to, it is correct. (it shows it's 3.62 vs my current 2.xx) Many peeps have had no problem upgrading to it. (most find it a very good Rom from the varios sites I read)
And this page at HTC still has it up:
http://www.america.htc.com/support/8525/software-downloads.html
JETninja said:
Ok, PC is fine, close any running programs. Hermes has stock WM5 with some programs added. Only reg tweaks are PTT and removed 3G animation at start.
Device syncs normally every day and both Work and Home.
When I follow all the directions, run the Updater - The PPC gets the Color Bars as the Updater is trying to read it....then AS (V4.5) disconnects and closes. (gone from taskbar) I can soft reset the device, reopen AS, they sync just fine. At this point I have the updater do the next, it pulls up the Current ROM info and says it will upgrade to the new one. I select next, and it starts.....and AS closes again. After a minute the upgrade app says it lost connection. (duh!)
Any ideas why?
I'm not a stranger to upgrading roms on PPC's, have several that have both been updated a number of times. No issues, though that several AS versions earlier.
I've given thought to Hard Reseting the device, but I'm wondering if its more AS's fault.
Any and all input much appreciated!
Thank You!
Click to expand...
Click to collapse
You just need to wait for a while AS shuts down that is normal be patient and it will start updating you will see a progress bar will take approx 10 min after that
@brorex he can wait till christmas next year, if the updater cant communicate with the device , because it has closed AS then it will never update.
@JETninja
try doing what i said to this guy here,
http://forum.xda-developers.com/showthread.php?t=341282
yesterday he upgraded with the same rom and device and it worked
brorex said:
You just need to wait for a while AS shuts down that is normal be patient and it will start updating you will see a progress bar will take approx 10 min after that
Click to expand...
Click to collapse
I thought that too, but after the color bar test when it want to set you up to actually install the ROM, the Upgrader whats you to make sure there is an active connection with AS. Well, there isn't. It shut down and the PPC is still showing the color bars. I can reset it, then re-sync to AS. (after having to re-launch AS from the Program Files - it no longer resides in the Tray when it shuts down during the process) I then get it going again, it attempts to start the ROM upgrade, AS quits again.....about a min later I get the Communication Error message....
I'm downloading a 2nd copy right now, will try it as soon as it completes...
*Edit...think I have an idea what I'm doing wrong, I have it connected and synced too early, the first part of the ROM updater is just a PC test, I'm thinking the PPC should not have been connected at that time. Re-trying it now.....
Try putting it in boot loader and upload...thats what i did when i updated my 8525...Very much like the new ROM...
Going to give it a shot here at work on this PC. If no go still, will try the above mentioned methods. PC at home kept getting communication errors...
i had the same problem
make the connection at AS then start the update process.... the 8525 will go into 3 bar mode and when the update gets to the upgrading rom screen... the installed rom wont show up.... hit upgrade... and then continue and it will work.... i was stuck there for a while too because if i waited for the istallation to load then made the as connection the right image would show up in the installer but then it would stop working after that.....
I just put this rom on my 8525 and it worked well for me. My 8525 is unlocked with supercid so I had to extract the OS and update using the methods described for working with SPL-140 Olipro with IPL-1.01 or the "How not to Brick thread".
That won't help you much as you don't want to do that mod to your New 8525 and void the warranty, but thought you might like to know the stock OS seems pretty stable at this point and I have had no problems yet.
Thanks everyone! It finally worked here on my Work PC. At home I could get to the Bootloader, but it would lose connection for some reason. Here I lost it the first time, but tried it again and it managed to stay connected and apply the update. Got it up and running, applied owner info, just now re-doing the AS relationship. (a good 500+ contacts! LOL! It'll take a little while as usual!)
Then it's back to all the tweaks I like so far...and some new ones I've held up on since I've been waiting for WM6.
Out of my 3 PDA's (2 ipaqs and this puppy) this one has certainly been the trickiest ROM update, but it seems to be more my device since most don't have this much trouble.
Thanks again!
So far- So good, but just one problem- BATTERY!!!
After I installed upgrade, my battery drains in few hours... I reset phone, I reloded upgrade- nothing helps! Warranty still in affect, but phone worked well and I'm positive- hardware is OK. What else can i do to fix this problem?
I have the same problem
ai6908 said:
Try putting it in boot loader and upload...thats what i did when i updated my 8525...Very much like the new ROM...
Click to expand...
Click to collapse
I have the same problem exactly. As soon as I start the upgrade the device immediately sleeps and the connection is lost. 1 minute later I get a Connection error message.
I am new to all this. How do i put the machine in 'boot loader' mode?
Thanks
Just did this rom update again on a 8525 the installation went extracting files active sync shut down wait a few minutes nothing happens the the upgrade screen no ACTIVESYNC connection while update is happening as soon as device is in bootloader mode activesync closes out
I have just joined the community and updated my TYTN to 4.31 ROM - look great
I was wondering if anyone is facing my problem:
I have set in the Pwer settings to "turn off the device after XX minutes"
The device does turn itslef off, but it seems that only soft reset can get it back on!
The hard buttons are not responding, the devce cannot even accept calls!
Did anyone face the same problem and manage to resolve it?
As a workaround, I am currenty using, Not to trun off the device, which probably consumes alot of battery!
no i don't have this problem it is working OK with me with same schaps rom 431
did you update your bootloader? I would hard reset again. If that doesn't work then try to reflash. Make sure your bootloader was updated first though.
Lets me see if I got this straight
When I load the RGB screen, I see this information in the RED block:
HREMES200
IPL-1.01
SPL-1.40.Olipro
The Device information shows
ROM Version: Schap's 4.31
ROM date: 10/03/07
Radio Version: 1.16.00.00
What is the bootloader exactly?
What should I select when I run the Schap's 4.31 ROM, there are several options there
BTW - the OS is SLOW, is that how it is with every wm 6.1 for Hermes devices?
I got confused when I first flashed a different rom (after installing HardSPL Olipro) - I just choose Safe SSPL as a tutorial recommended I do, and I've flashed three ROMs now without an issue just by using the Safe SSPL option.
After reflashing (and updating to hardSPL) I managed to find out the problem - it was the hebrew language by Orange which has casued this.
After removing it all worked well (almost)
Hi guys
I recently upgraded my TP2 to WM 6.5 downloaded from HTC themselves. after about a month the device keeps crashing with this device.exe error message on the screen then i cannot hear calls received should i put the phone into vibra mode or silent mode. the person can hear me though. i have to restart to fix this.
is there a patch to fix this somewhere ?
Try a hard reset and see if the problem is solved. Make sure you have backup everything you want to keep Otherwise I suggest you try a cooked rom. In my opinion they are superior to the stock ones.
Did the 2.29.405.2 update OTA initially and noticed problems. So reinstalled it from SD card but no help.
Bought sim free, unbranded/locked and never rooted:
Cannot dial out from phone lists or contacts. Going to phone and clicking on an entry in the call list does not launch phone call any more. Going to contacts, opening one and clicking on an available phone number does not launch phone any more.
The only way I can make a call is to punch it in on the keypad! Grrr.
Wifi connects to my home base after a reboot but, after an undetermined amount of time it drops the connection and cannot get it again. Going to Wifi settings shows it scans, connects and tries to obtain IP address. After a short time it gives up, turns wifi off and starts over. Again & again.
Cannot get it to connect again without another reboot.
This is a crippling loss of functionality for me. Can anyone suggest a way to roll back this update so my phone works as id did?
Many thanks all,
M1
First try a hard rest(you will lose all personal data on the phone,pictures and other stuff on the SD will be fine). If that does not work try either the 2.29.405.2 or 2.10.405.2 RUU.
More info - to my horror, around 15 minutes after I had tried and failed to make calls from contacts the phone started making them one after the other as if they were stuck in a spool or something! Ouch - any thoughts?
Backup everything you can and flash the same ruu from shipped roms.
Sent from my HTC Desire using XDA App
> flash the same ruu from shipped roms
where do I find this? - android noob!
http://shipped-roms.com/download.ph...9.00.32U_5.11.05.27_release_151783_signed.exe
And if it works, keep it safe!
Sent from my HTC Desire using XDA App
Thanks to all for help on this. Decided worth a trouble shoot before a hard reset and culprit seems to have been an app - extended controls widget. Removed this and all seems well again.
Try this one. This definately works! i have used it.
http://forum.xda-developers.com/showthread.php?t=768256
I was stuck at 2.29 update.
Then i used this guide and windows tool.
So i did this process and it rolled my phone back to stock android 2.1 rom 1.X
The first version that the phone was bought with.
This tool will boot the phone into bootloader and load a stock 1.x rom ota off the sd card as the tool will extract it to sd card and then load it.
This will wipe all your data not sure about the sd card as i dont remember any of that because i formatted my sd card after i had used the tool.
Thats because i had rooted my phone and tried custom sense hd rom.
The only reason i had was of the battery usage as the consumption was very badly increased and that the 2.29 rom was unstable.
PS: I did first try the htc service in Denmark. They couldn't help me and said i was stuck with the 2.29 rom update. :/
After my phone got rolled/flashed back to stock android 2.1.
The next day in the morning i could upgrade again to android 2.2 rom ver. 2.10 OTA from htc servers.
Maybe this works for you as i did for me and others.
Turns out it wasn't the app.
After a couple of days playing ok my sim free stock htc desire is unstable again.
Cut me off mid call - went to phone and clicked on last call entry - absolutely nothing happened, repeated with same problem. Exited phone to home screen then opened contacts and tried to make call from there - same behavior, a complete hang.
No web access either so opened wifi manager to find it hanging on "obtaining IP address" from my home network and continually shutting down and restarting wifi automatically at this stage.
Noticed general UI lag and several apps failing to open too.
Left phone alone and again, around 10 minutes later all of the actions - including trying to make the phone calls started running one after the other. Like everything had been caught in a spool or something. After this all seemed OK until it happened all over again later.
Although the UI seemed OK and some apps worked as expected, the only way to get phone and wifi working whilst it was hung was a warm boot.
Dreading a hard reset as it's going to waste another day or two getting everything reconfigured just so (can't find a back up solution that does everything - multiple mail account settings etc) but looks like only option.
Will try going back to mikep99's suggested rom as soon as I have time and will not be responding to an HTC OTA auto update offer again.
Grrr.
I still suspect an app conflict.
Can anyone recommend a util that might give me a clue which app / sys process could be hogging system / radio resources?
just got another OTA update pushed to me. installed (nothing to loose) and Congratulations my phone has been updated to 2.29.405.5.
Not sure whats going on here as that was the update I got 2 days ago. This time round it was only 4.8mb download so I'm assuming it's an update update. Hope it fixes things .....