Develop Bugs

My FSC-n560 is bricked. Help please!

Hi!
I was using Newplow's WM6 038 ROM with my N560.
Yesterday I tried to write another ROM(WM6 038 with 8MB pagepool) but during update got an error.. It said it just failed.
Now my N560 is stuck on booting screen(people climbing mountain..)
I tried Warm, Cold, Hard reset but with no luck.
Even the power button doesn't work so I had to remove battery. When I insert battery it powers on by itself.
I can enter bootloader screen by pushing power+record button so I tried to copy rom image file to SD card but it doesn't work.
I tried two ROMs(OS_213U.nbf from Original WM5 ROM and Newplow's) and 3 SD Cards(2GB SD, 1GB MicroSD with Adopter, 16GB SDHC)
Is there any recovery tutorial in bootloader mode?
Help me please!
Sorry for my English.

Have you tried flashing a ROM through the computer rather than the memory card? Try going into bootloader and flashing that way rather than the card.

The pagepool ROM is meant for N560s that have been upgraded to 128Mb RAM... have you upgraded the internal RAM to 128Mb? If you have not, then this may have caused your problem.
I had this problem when flashing to 038 normal RAM (from 035). A hard reset reset to the normal start screen, but nothing worked. However, trying a new burn with the Loox flash tool restarted the process and it worked. I found the cure was to make sure you hard reset the N560 before doing a burn. It appears to be that you have to do this to release enough RAM for the burn program to reside and for "working" storage. You may not have done this.
I suggest you try simply re-running the flashtool with SD/SDHC cards removed, battery in place, on the cradle via your PC, even though it appears stuck. The signals coming from the USB link may wake up the bootloader routine in the N560?

Solved the problem! Thanks for your comments!
I asked same question in Newplow's guestbook and the person who made pagepool rom answered. I used MTTY to revive my pda.
What I did is in below post. need translation
http://4pda.ru/forum/index.php?showtopic=55274

Hi all,
I have the same problem. N560 is stick on the himalaya picture. I tried to falsh from WM5 to new rom for Wm6 and after installation the pda stuked. So I did a warm reset and now only the start picture is apperaing. Problem is that battery is down now.
Can someone give more info on the process followed to revive the PDA ? I just cannont read russian (may be Jinsu77 ?)
Many thanks for support in advance

same problem here please please please someone help us
the only thing i can do is the l c:\os_213u.nbf on mtty program and nothing else happend to the machine
sorry for my english

read, and pay attention here:
[email protected]@p://a.mod-site.net/gb/u/newplow-1.html
POST 203.

It was me asking on Newplow's guestbook.
In case you're using Vista, you need some trick to be able to rom update. Read below.
http://www.modaco.com/content/windo...u-on-vista-it-can-be-done-the-ultimate-guide/
And then you need to download MTTY (I used version 1.42, got it by googling) and follow below steps.
(used google translation from 4pda.ru)
------------------------------------------------------------
For rom update without ActiveSync.
1) take this set of extract, copy it to the folder with the firmware.
2) copy the file os_213u.nbf example in C: \
3) You press the button Recorder + food and poke in the hole reset (Recorder button and hold until you eat dolphins)
4) plug the device to a PC, the Task Manager, shooting process - wcescomm.exe
5) Run mtty, choose Port: USB, connect.
6) If mtty caused an error and shut down, simply restart mtty, if not typed commands, then repeat the procedure with paragraph 3.
7) in mtty command, enter: (first letter in kommande - a little l l от слова from the word L L oad)
> l l c:\os_213u.nbf c: \ os_213u.nbf
Since the end of the process will be an inscription about the error, remove the device from the PC.
9) Run rom update, zhmete "next", until you see dolphins.
10), plug the device to a PC and program.
---------------------------------------------------------------
Hope this helps you all

in advance sorry for my english
I am doing all the instructions carefully and the mtty show this
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,1A0F023Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
the pda shos the dolphins and the full blue bar
after without change anything i run the PocketLOOX5xxFlashTool that i have in the same folder with the :
EnterBootLoader.exe
OS_213U.nbf (originally rom)
RUUServer.dll
RUU.dll
and the only thing i can see is that the PocketLOOX5xxFlashTool is trying to find the pda without any luck
also the pda is stucked in the same screen with the dolphins and the blue bar
do you see any mistake in this procedure

Helppp!!! please

tuluba said:
Helppp!!! please
Click to expand...
Click to collapse
have you closed EVERY process of activesync before proceding with mtty?

I close the wcescomm.exe and the rapimgr.exe is there anything else?

The pocket LOOX 5xx FlashTool cant connect with the N560 and at the and says that Error"The language in this Flash Image update (ENGLISH) differs from that on your device()!" and i have always english rom exept maybe from the last rom "the killer" with the 128MB rom that i dont know if it is an english or something else because the device never opens to see

After flashing in MTTY(don't care about error messages), you need to unplug your n560 from PC. And then proceed romupdate until you see the dolphin picture. Now you plug n560 to PC and cilck next and wait for a while.. Hope it works!

I change the language of the rom and it works
thank very much all of you

At all they have Probs with flash from SD Card: only use a Card with 512MB! I think a Card greater then can't read by the Bootloader....

hey.
i am compeletly new here. I have the same with my n560. I tried to upgrade to 128mb but after restart I see only climbing. I tried everything here but on dolphins afterr line is blue it is finished. that I am unpluging device. starting looxflastool for 560 and first is trying to connect by active sync and that when no connection made I see dolphins on left screen of flash tool window. than I am pluging again and after couple secs I see that: Error"The language in this Flash Image update (ENGLISH) differs from that on your device. I tried to change rom on every language but not working as well. PLEASE HELP

if that helps than i will add than on top when delfins i see on 560 is two lines. first is typed 2.14.G4 on second directly below is 2.15.
and when mtty 1.42 finishing flashing i see following:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0224002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)

Need help!!! Please!!!
I bricked my N560. I tried to downgrade from WM6 to WM5 and now I see only delfins and in the first line "2.14.G4" and in the second line "2.15"
What can I do?? How can I flash WM6 or WM5 ROM when there is no connection to the PDA????

ChrisDo said:
Need help!!! Please!!!
I bricked my N560. I tried to downgrade from WM6 to WM5 and now I see only delfins and in the first line "2.14.G4" and in the second line "2.15"
What can I do?? How can I flash WM6 or WM5 ROM when there is no connection to the PDA????
Click to expand...
Click to collapse
You can usually get back to the boot loader if you do a hard reset. I am sure you know how, if not you will find it in the FSC CDROM manual that came with the device. Let us know if this works? I have got stuck at this point too, so I know it works..... hopefully!

Rom upgrade problem

Last night I wanted to install the official new dutch Vodafone rom for my diamond, from 1.37 to 1.97, so I started reading on the forums.
First I did a hard SPL, and now I have a SPL-1.30. Olinex, so I think that is right.
After the hard SPL I tried installing the RUU, but every time it starts installing, the progressbar stays at 0% and after some minutes, i get an 262 error. I tried it at several PC's, XP, Vista, Windows 7. So that is not the problem.
Anyone has an idea how to fix this?
greetings from holland, and sorry for my crappy english

Anyone has an idea, im realy wanting to upgrade

Sounds like u did everything right....but when flashing, using your pc is the last solution. Always flash Radios or Roms using the internal method.
Got this from Suiller:
COOKING ROMs & Radios from phone =-
1. open from your PC the rar or zip archive and extract only the BIG .nbh file
2. rename as DIAMIMG.NBH
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!)
4. soft reset your device and within 3 seconds push together the Vol_Down + Back button (the one on the right above the hangup button) and keep pressed until the boot loader appears (the one with the color stripes)
5. soon as you see the bootloader stop to press those poor buttons
6. a very simple gray menu will appear asking you what to do, simple press the power button to perform the ROM/Radio upgrade
7. while the upgrade runs be patient and don't press again the power button, reset the device or play with it until it finishes, when finished a message "UPDATE SUCCESS" will appear, now you can safely reset your device
8. who prefer can perform a hard reset after the fresh cook (soon after reset simply press Vol_Down + Circle button, then when you see another simple gray menu choose Vol_Up to confirm format), even if this has no-sense because internal memory is pre-formatted during flash, but... there is always a but... for some unknown "scientific" reason sometimes an hard-reset can save time & headache
I only hard reset after a new Rom has been installed.........I don't do this for Radios.

I have the vodafone 1.97 rom on my computer, but it is an exe file. And I can't unrar it. So where can I find that big.nbh file?

I placed the nbh file, and i called it DIAMIMG. But when i boot, i get a grey screen that says loading and doesn't goes away.
Help needed!

HTC-P said:
I placed the nbh file, and i called it DIAMIMG. But when i boot, i get a grey screen that says loading and doesn't goes away.
Help needed!
Click to expand...
Click to collapse
i know this may sound silly buy i am sure it must be like this diamimg.nbh
not DIAMIMG.
i hope this helps

HTC-P said:
Last night I wanted to install the official new dutch Vodafone rom for my diamond, from 1.37 to 1.97, so I started reading on the forums.
First I did a hard SPL, and now I have a SPL-1.30. Olinex, so I think that is right.
After the hard SPL I tried installing the RUU, but every time it starts installing, the progressbar stays at 0% and after some minutes, i get an 262 error. I tried it at several PC's, XP, Vista, Windows 7. So that is not the problem.
Anyone has an idea how to fix this?
greetings from holland, and sorry for my crappy english
Click to expand...
Click to collapse
Change the hard-spl to 1.93 olinex and your problem is over, has worked for me with all roms so far. And when you flash, put your phone in bootloader mode manualy and your flashes works every time.
And if the rom is a exe file you can forsure unzip it!! use right tool for that, ex. winzip and you have your .nbhfile
If the file is DIAMIMG.nbh you can rename it to RUU_signed.nbh and fla**** with udK.s Custom RUU

Maybe it's a noob question but where can i find the 1.93 version. And can i just install it over the SPL 1.30 version?
And how do i put it in manual boot?

Here you have the 1.93 version
http://forum.xda-developers.com/showthread.php?t=400950
just flash the new one over 1.30 version
Manual boot
Volumedown + reset (hold it down for a while, and the 4 color screen will appear)
Put manual boot only when flash rom!! not hard-spl

It finally worked! Thank you all!

Official Diamond ROM 2.03 update - HELP

Hey guys,
I have no idea what's going on. I appreciate your suggestions. I flashed my Diamond many times (and other phones as well) with most of the ROM available. Unit a month ago or so I've been using the official 1.93 ROM with previously installed hard SPL 1.40. When I attempted to install a new 2.03 ROM I went through the whole procedure same way as always with a little exception. Right after completion - 100% the unit reboots, shows the rainbow screen with a message "Upgrade ROM code error" - try again. What is the world is this? I also have a message on my desktop "Error 270-update error" - The image file is corrupted. My unit is european and I downloaded the ROM from both US and Euro sites. From this point I managed to downgrade again to version 1.93. Then I ran again the hard SPL 1.40 and reattempted to upgrade to 2.03 - SAME THING!
I don't know what to do next. Why I cannot flush it with the latest ROM? Any ideas or similar situations? Please see picture.
Thanks

Same Thing happened to me :S wtf??

xevier69 said:
Hey guys,
I have no idea what's going on. I appreciate your suggestions. I flashed my Diamond many times (and other phones as well) with most of the ROM available. Unit a month ago or so I've been using the official 1.93 ROM with previously installed hard SPL 1.40. When I attempted to install a new 2.03 ROM I went through the whole procedure same way as always with a little exception. Right after completion - 100% the unit reboots, shows the rainbow screen with a message "Upgrade ROM code error" - try again. What is the world is this? I also have a message on my desktop "Error 270-update error" - The image file is corrupted. My unit is european and I downloaded the ROM from both US and Euro sites. From this point I managed to downgrade again to version 1.93. Then I ran again the hard SPL 1.40 and reattempted to upgrade to 2.03 - SAME THING!
I don't know what to do next. Why I cannot flush it with the latest ROM? Any ideas or similar situations? Please see picture.
Thanks
Click to expand...
Click to collapse
Hi have you tried to flash from the internal storage?

Have you tried flashing with internal storage method?

Exactly the same problem here, so I tried to flash to a really old original HTC ROM after the failure and it flashed fine
So I thought I would try upgrading over the top of an original ROM, had the same error , bloody HTC

So, any ideas how to resolve this issue? Are we stuck with the old ROM? I'm glad that I'm not the only one experiencing the same problem.
No, I have never tried to flash from internal storage. How can this be done? do I copy the whole .exe file to storage and run from there? Any pre-cautions?
Thanks

Though I bricked my phone when it happened, never seen that error before despite many ROM flashes
I have now tried tommytaos ROM which is supposed to be very close to the original but some with some tweaks.
http://forum.xda-developers.com/showthread.php?t=479049
It installed just fine on my phone. Seems HTC have broken their ROM

xevier69 said:
So, any ideas how to resolve this issue? Are we stuck with the old ROM? I'm glad that I'm not the only one experiencing the same problem.
No, I have never tried to flash from internal storage. How can this be done? do I copy the whole .exe file to storage and run from there? Any pre-cautions?
Thanks
Click to expand...
Click to collapse
it's the best way to flash the rom and the safest...
From Suiller thread:
the standard procedure to cook a ROM is made trough activesync program, I mean that the .nbh file is pushed into the phone trough activesync, across the usb cable, but this procedure can give some troubles:
1. it takes long time, about 10 minutes
2. it's a bit unsafe (even if the procedure can be always restored safely)
3. it's possible only with Windows OS (NO Linux nor *BSD, et cetera...)
I don't know why this is not well known but ALL producers (like HTC) give the possibility to upgrade the rom/firmware without having MS windows (thanks GOD someone knows that there aren't only windows users).
This faster procedure can be done also with *nix variants (or whatever you use) because the ROM update is made directly by the phone.
The procedure is very simple, it will take just 2 minutes, can be done everywhere & is good for cooking radios too (very fast in this case)
-= COOKING ROMs & Radios from phone =-
1. open from your PC the rar or zip archive and extract only the BIG .nbh file
2. rename as DIAMIMG.NBH
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!)
4. reset your device and within 3 seconds push together the Vol_Down + Back button (the one on the right above the hangup button) and keep pressed until the boot loader appears (the one with the color stripes)
5. soon as you see the bootloader stop to press those poor buttons
6. a very simple gray menu will appear asking you what to do, simple press the power button to perform the ROM/Radio upgrade
7. while the upgrade runs be patient and don't press again the power button, reset the device or play with it until it finishes, when finished a message "UPDATE SUCCESS" will appear, now you can safely reset your device
8. who prefer can perform a hard reset after the fresh cook (soon after reset simply press Vol_Down + Circle button, then when you see another simple gray menu choose Vol_Up to confirm format), even if this has no-sense because internal memory is pre-formatted during flash, but... there is always a but... for some unknown "scientific" reason sometimes an hard-reset can save time & headache
notes:
* be sure to have at least 10/20% of charge, anyway the whole procedure will take about 2 minutes, so you must be ensure that your mobile will stay turned on for at least those 2 dirty minutes (just in case you can attach the power AC/DC too), don't panic if something goes wrong... read few lines below
* like told you above the same procedure is good for cooking Radio too, of course Radio are smaller and it will be really fast (about one minute!)
* you don't need windows anymore or activesync, is enough just to copy the file into the storage card (transfers WITHOUT activesync are faster)
* it's possible to make a reset simply by getting off the stylus and pressing the small red button under the stylus carrier
* don't worry if something goes wrong... any cook failure can be always restored, the important thing is that you don't fail hardspl flash... but you have to do it just one time in your life
special note about hard-spl:
if you have signed-only hard-spl I strongly suggest to upgrade to an un-signed one, personally I tested many & I can confirm that the "good ones", at least in my experience, are the Olinex 1.37 or 1.93, you can find a copy here
remember also that you can NOT brick your device if you have a good hard-spl (like the ones I mentioned above) & flashing directly from phone is really faster (also good for flashing radio)
so the only one thing you should take care is when you change/upgrade the hard-spl, but you have to do this step just once, I'm using this hard-spl from about 6 months & I was able to flash everything (plus dozen recovers for failed flash)
for rom/radio upgrades you can safely also reboot/remove cable/turn off your phone while flashing ...every lost flash can be always restored safely, it's enough to restart your device in boot mode & restart flashing, also with cable trough the classic RUU (to put device in boot mode simply reset & keep pressed Vol_Down button)
In the hope this procedure can be useful at least to save time

if you have the official rom which is a exe file you can extract the rom file using winrar.

EUREKA!!! Done Deal!!!
Flashed from Internal Storage as per following directions:
-= COOKING ROMs & Radios from phone =-
1. open from your PC the rar or zip archive and extract only the BIG .nbh file
2. rename as DIAMIMG.NBH
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!)
4. reset your device and within 3 seconds push together the Vol_Down + Back button (the one on the right above the hangup button) and keep pressed until the boot loader appears (the one with the color stripes)
5. soon as you see the bootloader stop to press those poor buttons
6. a very simple gray menu will appear asking you what to do, simple press the power button to perform the ROM/Radio upgrade
7. while the upgrade runs be patient and don't press again the power button, reset the device or play with it until it finishes, when finished a message "UPDATE SUCCESS" will appear, now you can safely reset your device
8. who prefer can perform a hard reset after the fresh cook (soon after reset simply press Vol_Down + Circle button, then when you see another simple gray menu choose Vol_Up to confirm format), even if this has no-sense because internal memory is pre-formatted during flash, but... there is always a but... for some unknown "scientific" reason sometimes an hard-reset can save time & headache
THANKS! THANKS! THANKS!

Flashing using the Internal Method is the safest and most convenient way to flash. Spread the word.......

xevier69, Thanks for your thread
Having just purchased Oli's security unlocker... I was annoyed about this problem with a HTC official rom!
But your method has solved this issue!
Thanks again

Thanks guys it works perfect!

This just happened to me too and the only roms i have ever flashed:
1.37 official spanish: came with the phone
1.37 official WWE
1.93 official WWE
and now 2.03 official WWE fails.
WTF... One would expect the upgrade not to fail, right?
I wonder if they are checking for HardSPL to be original too!?
Anyway thanks for the workaround

This worked for me to
Cheers
xevier69 said:
EUREKA!!! Done Deal!!!
Flashed from Internal Storage as per following directions:
-= COOKING ROMs & Radios from phone =-
1. open from your PC the rar or zip archive and extract only the BIG .nbh file
2. rename as DIAMIMG.NBH
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!)
4. reset your device and within 3 seconds push together the Vol_Down + Back button (the one on the right above the hangup button) and keep pressed until the boot loader appears (the one with the color stripes)
5. soon as you see the bootloader stop to press those poor buttons
6. a very simple gray menu will appear asking you what to do, simple press the power button to perform the ROM/Radio upgrade
7. while the upgrade runs be patient and don't press again the power button, reset the device or play with it until it finishes, when finished a message "UPDATE SUCCESS" will appear, now you can safely reset your device
8. who prefer can perform a hard reset after the fresh cook (soon after reset simply press Vol_Down + Circle button, then when you see another simple gray menu choose Vol_Up to confirm format), even if this has no-sense because internal memory is pre-formatted during flash, but... there is always a but... for some unknown "scientific" reason sometimes an hard-reset can save time & headache
THANKS! THANKS! THANKS!
Click to expand...
Click to collapse

Thers some other option
Install twice from activesync 1st time = error, run for the second time the same version and OK it updates.
At least with my Diamond had worked
Cheers

Hi!
The same thing happend to me too... I think it's because of the serial number we have entered when we have downloaded that 100 MB ROM Update file from the HTC support site... well i think it doesn't match with the serial and IMEI of the phone that the upgraded rom checks at the end of the update process... so i think it's kind of a protection against piracy developed by htc... taiwanese idiots!

Hi!
pls anyone send any information about an rom update file that works and doesn't report errors after it installed 100%. pls specify it's rom version too! 2.03 would be great
thanks in advance

miriamscorob said:
pls anyone send any information about an rom update file that works and doesn't report errors after it installed 100%. pls specify it's rom version too! 2.03 would be great
thanks in advance
Click to expand...
Click to collapse
read all posts please
works like a charm folks! thank you!

g0x said:
Thers some other option
Install twice from activesync 1st time = error, run for the second time the same version and OK it updates.
At least with my Diamond had worked
Click to expand...
Click to collapse
I made this too for testing First flash: Error, Second time: Ok

HTC TP2 bricked? Freezes at Start up!

Please help!
My HTC TP2 freezes at start up with the black screen and the Touch Pro2 Logo and some details in red at the bottom:
B 80
R 4.49.25.17
G 61.44tc.25.32U
D 1.86.67102
No USB connection can be established.
What happened:
1. Tried to update from original WM 6.1 to WM 6.5 by using the official HTC ROM update utility. Seems like USB connection broke during update and update freezed at 42%. Update utility process has stopped by itself (no process visible anymore in the Task Manager).
2. Restarted phone and multicolor screen appeared and stayed. After connecting with USB cable again "USB" appeared at the bottom. Started again the HTC ROM update utility which recognized the phone and started the update process again, but stopped at the beginning with an error message stating something like the ROM is broken.
3. Restarted again (by removing the battery and hit power button) and state reached like described above (HTC TP2 freezes at start up with the black screen and the Touch Pro2 Logo and some details in red at the bottom).
4. Performed a hard reset but did not help.
What can I do to bring the phone back to life?

So you can't or can get in the colored screen now? (the boatloader)
And it's kind of normal that their nothing happens after the tp2 + red information screen, this since their is no rom to startup.
EDIT
Is it possible to tell exactly what error you got?
EDIT
Try to hard reset your device, do you know how to do this?
If not this is how to do it:
To perform a hard reset
1. With the device turned off, press and hold the TALK/SEND, END and POWER buttons until you see this message on the screen.
"This operation will delete all your personal data, and reset all settings to manufacturer default. Press VolUp to restore manufacturer default, or press other keys to cancel."
2. Release the TALK/SEND, END and POWER buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
Source: http://forum.xda-developers.com/showthread.php?t=523083
This is just what worked for me..
Had the same issue on my tp...
Hope it will work for you.

Did already the hard reset - but this did not help as nothing changed!
One further info: whenever I insert the battery the device automatically starts up - until it freezes again at the start up.
Can someone please help?

It's normal that the device starts up when the battery is plugged in...
But this is just what I know out of my own experience.
So sorry I can't help you farther.
EDIT
Did some research you might want to try to flash your phone by micro sd... (not for sure if it helps but by some people it did work)
Read the tread about flashing at the top of the rhodium section and you know how to do it.

Did another trial: downloaded and copied a RHODIMG.nbh to the micro sd card, inserted it again and pressed volume up at startup -> colored screen appears shortly, then switches to a white screen telling "Loading..." in blue font color, but nothing more.
Is there anybody out there who can help?
Do I need a specific RHODIMG.nbh to make this approach working? I didn't flash this device before, so it has been still in the original manufacturer's state.

frieder01 said:
Did another trial: downloaded and copied a RHODIMG.nbh to the micro sd card, inserted it again and pressed volume up at startup -> colored screen appears shortly, then switches to a white screen telling "Loading..." in blue font color, but nothing more.
Is there anybody out there who can help?
Do I need a specific RHODIMG.nbh to make this approach working? I didn't flash this device before, so it has been still in the original manufacturer's state.
Click to expand...
Click to collapse
suppose 2 press down volume not up after soft reset

This may help,
Try entering bootloader by switching off device then switch back on holding down the Vol down key.
If you can enter bootloader this way then you wil be able to flash from SD card following the instructions from here
http://forum.xda-developers.com/showthread.php?t=550540
if you want to flash the Official update from HTC you can extract the Nbh from the Exe file you downloaded from them, just use winzip, Zzip or Win RAR to extract the contents from the Exe you are looking for RUU_signed.nbh..follow the above thread instructions to change the name of the file to RHODIMG.nbh.
I DONT KNOW IF YOU NEED TO HARD SPL FOR THIS..Probably better to do it than not. Can Anyone Confirm???
i hope this helps

Device is up and running again !
Could enter bootloader mode and tried first to install again via the official HTC installer -> worked!
Thanks a lot for your support!

great news welldone Bro and welcome to the forum!!!

osrix25 said:
This may help,
Try entering bootloader by switching off device then switch back on holding down the Vol down key.
If you can enter bootloader this way then you wil be able to flash from SD card following the instructions from here
http://forum.xda-developers.com/showthread.php?t=550540
if you want to flash the Official update from HTC you can extract the Nbh from the Exe file you downloaded from them, just use winzip, Zzip or Win RAR to extract the contents from the Exe you are looking for RUU_signed.nbh..follow the above thread instructions to change the name of the file to RHODIMG.nbh.
I DONT KNOW IF YOU NEED TO HARD SPL FOR THIS..Probably better to do it than not. Can Anyone Confirm???
i hope this helps
Click to expand...
Click to collapse
For future info, from what I have gathered you must hardSPl for all ROM flashes. If the ROM you flash is the stock ROM, you can also revert your SPL to stock. For any other ROM, you must leave your device hardSPL'd.
Hope I helped.

how were you able to connect the phone with the pc. i seem to have a similar problem but am finding it difficult to connect the phone to the pc. i have activesync installed but cannot connect to the phone

osrix said:
This may help,
Try entering bootloader by switching off device then switch back on holding down the Vol down key.
If you can enter bootloader this way then you wil be able to flash from SD card following the instructions from here
http://forum.xda-developers.com/showthread.php?t=550540
if you want to flash the Official update from HTC you can extract the Nbh from the Exe file you downloaded from them, just use winzip, Zzip or Win RAR to extract the contents from the Exe you are looking for RUU_signed.nbh..follow the above thread instructions to change the name of the file to RHODIMG.nbh.
I DONT KNOW IF YOU NEED TO HARD SPL FOR THIS..Probably better to do it than not. Can Anyone Confirm???
i hope this helps
Click to expand...
Click to collapse
is it possible to connect to active sync in bootloader, cos my phone cannot even boot, it freezes up with a white screen and htc logo.

After entering bootloader you can flash either way,either by ruu package provided by your ROM's maker or running official ruu release or if you have the renamed file on the root of your sd card....I never use sd card flashing and have never had a failed flash...If in bootloader it will not connect with activesync,but device should be recognized by ruu.exe
WC

Help htc touch diamondtive sicron.

Hay i have htc touch diamond how to uptade wm 6.1 to 6.5 ? I try to connect wia active sicron. But cannot uptade

[link 1], [link 2]
Link 1 is the same thing with link 2.

Tanks on fasst answer i got 4 colors screen , red ,yelow , blue ,white on top writte diam100 64m spl-1.37 i pressing power button nothing happening ,help . I new one here

Connect your diamond to PC as a disk drive (mass storage) and copy your ROM to Internal Storage. Make sure it`s name is "DIAMIMG.nbh" (*.nbh is the extension, make sure it is only once, not like this: "DIAMIMG.nbh.nbh" ) and than hit the reset button and hold vol down + back key. After update make a hard reset, hit the reset button and hold vol down + center key and follow the instructions on the screen (vol up to format only phone memory).
I hope you understood.
Good luck!

This part is ok now writte "trigger usb host " noting happend but i clean f disk ( memory internay ) only left image file how to run update ?

So... put "DIAMIMG.nbh" into Internal Storage (root). Unplug you diamond from PC, hit the reset button, and hold vol down + back key, press power key, wait for update to complete.

thecrazyman64 said:
So... put "DIAMIMG.nbh" into Internal Storage (root). Unplug you diamond from PC, hit the reset button, and hold vol down + center, press power key, wait for update to complete.
Click to expand...
Click to collapse
Vol down + the back button

i did do this go info no image file i have version 1.37 what rom i must use ?Even to update windows to 6.5 english

Tajanstveni said:
i did do this go info no image file i have version 1.37 what rom i must use ?Even to update windows to 6.5 english
Click to expand...
Click to collapse
Just going by my Diamond and what you said in a previous post, it should say (quoting my diamond) "SPL-1.24. Hard"
You can't flash custom ROMs with a stock SPL.
Link for HSPL is in here, read along with it.

I tray to download renamed it put in root but when start loading file mising image file writte why?

Tajanstveni said:
Hay i have htc touch diamond how to uptade wm 6.1 to 6.5 ? I try to connect wia active sicron. But cannot uptade
Click to expand...
Click to collapse
please read this - http://forum.xda-developers.com/showpost.php?p=2508373&postcount=1
its one of the basic things we do... and you will get most of answers here...
this is 3rd topic on the forum for diamond - http://forum.xda-developers.com/forumdisplay.php?f=430
you can see other useful posts as well.... MTTY is highly recommended when you flash new rom to diamond...

Tanks for asnswer fast but problem is that i cannot conect device with pc when i start diamond ruu program later i get error 224 What i need some drivers for reconect to pc? I use microsoft active sycn 4.5 but i cannot coneect completly come message on display . Exist another method to connect touch diamond to pc ?

After factory default reset and format internal storage now is problem when i try to start rom uptadte from internal storage writte "loading ...." i wait more that 10 min nothing happend only loading.... where is the pronlem

Tajanstveni said:
After factory default reset and format internal storage now is problem when i try to start rom uptadte from internal storage writte "loading ...." i wait more that 10 min nothing happend only loading.... where is the pronlem
Click to expand...
Click to collapse
If you can connect to activesync (should be possible, since you are back to original),
use the customRUU method. At least that should give an idea of where the process is getting wrong, plus will allow recovery.
HTH...

Same Problem?
Tajanstveni said:
Hay i have a problem wih htc touch diamond when i tray to connect to pc with active sync 4.5 said that device cannot be sicnoized completly and i cannot update costum rom come error 224 device not found ,can anibody help me ?
Click to expand...
Click to collapse
Looks like you created a new thread for the same problem...
http://forum.xda-developers.com/showthread.php?t=643159

Sorry for my mistake but probolem solved ,tanks for help