Vario 2 & Bluetooth - 8525, TyTN, MDA Vario II, JasJam ROM Development

All,
I have a T-Mobile Vario2 and have tried several WM6 roms and keep getting an error with the Bluetooth.
I have tried to pair several devices e.g Holux 236 and Sony BT HBH60 headset but the phone keep giving me an error saying Bluetooth Hardware Failure.
Also when I tick the the option to keep bluetooth on and go back and check the option has been deseleted automatically. I cant seem to keep the option ticked.
Why is this happen? I have tried the official TyTn ROM and T-Mob WM6 both giving me the same problem?
I am using the following radio verison = 1.50.00.00
I have never dropped the phone and have HardSPL installed.

msuk said:
All,
I have a T-Mobile Vario2 and have tried several WM6 roms and keep getting an error with the Bluetooth.
I have tried to pair several devices e.g Holux 236 and Sony BT HBH60 headset but the phone keep giving me an error saying Bluetooth Hardware Failure.
Also when I tick the the option to keep bluetooth on and go back and check the option has been deseleted automatically. I cant seem to keep the option ticked.
Why is this happen? I have tried the official TyTn ROM and T-Mob WM6 both giving me the same problem?
I am using the following radio verison = 1.50.00.00
I have never dropped the phone and have HardSPL installed.
Click to expand...
Click to collapse
Is it still under warranty? It sounds like you tried everything, it may be broke. If it's not under warranty, search and see if you if you can find a picture pointing to the bluetooth/wifi chipset and physically check each leg of the chip. Maybe it's a cold solder joint on the chip. good luck.
Chris

Related

[HTC 8525 + WM6] Bluetooth keeps disconnecting

Hello!
I do not know if someone has the same issue. I upgraded the WM6 to my HTC 8525 and bluetooth just keeps disconnecting all the time. It happened without any reason at all. I am using "Plantronics 510". The headset is fine, just phone switches the bluetooth off and I need to go to settings to switch it back on. I saw some people have a problem with car-enabled bluetooth. Not sure if it is the same problem.
Any advice? Does someone get the same problem? Any patch or solution?
Thank you!
viva_unix said:
Hello!
I do not know if someone has the same issue. I upgraded the WM6 to my HTC 8525 and bluetooth just keeps disconnecting all the time. It happened without any reason at all. I am using "Plantronics 510". The headset is fine, just phone switches the bluetooth off and I need to go to settings to switch it back on. I saw some people have a problem with car-enabled bluetooth. Not sure if it is the same problem.
Any advice? Does someone get the same problem? Any patch or solution?
Thank you!
Click to expand...
Click to collapse
which WM6 ROM are you using?
I had this problem with my Audi A4 car phone. The ROM versions using build Build 17745.0.2.3 were not good for that. Now, I'm using the Black Majik ROM and that works like a dream for the BT connections.
walshieau said:
which WM6 ROM are you using?
Click to expand...
Click to collapse
I have Cingular HTC 8525 [HERM100]
ROM Version: 3.30.2.1
ROM Date: 04/17/07
Radio version: 1.41.00.10
Protocol Version: 32.74.7020.18H
viva_unix said:
Hello!
I do not know if someone has the same issue. I upgraded the WM6 to my HTC 8525 and bluetooth just keeps disconnecting all the time. It happened without any reason at all. I am using "Plantronics 510". The headset is fine, just phone switches the bluetooth off and I need to go to settings to switch it back on. I saw some people have a problem with car-enabled bluetooth. Not sure if it is the same problem.
Any advice? Does someone get the same problem? Any patch or solution?
Thank you!
Click to expand...
Click to collapse
Did you manage to solve this? Is so how?
Thanks
Msuk
i started having the same problems but i noticed it after i installed the voice command.. the rom that i use is the gm360 gold. the problem ive got was whenever i was in a phone call using my blutooth and i received a text message it would deactivate my headset. if ur having somewhat of the same problem try disabling ur voice command software...
Multiple AT&T/HTC WM6 ROMs?
My 8525 with the WM6 ROM can no longer route the audio to the BT headset (a Moto HS850 - but this is irrelevant, I suspect).
Basic BT headset usage was fine with WM5 (excepting the known issues with VoiceCommand).
I thought that perhaps the issue was related to the various little registry tweaks and sw patches. However, I had to do a reflash (for other reasons) and currently have just the default WM6, no registry tweaks, no BT sw patches, and MS VoiceCommand 1.6 installed (but set to NOT use the BT headset).
Pairing works fine. So does activation recognition (i.e. the little headset appears in the notification area when I open the boom on the headset and I can hear the background establishment of the BT channel). But audio (dialing tones and Connected call audio) do not reach the headset. The audio also doesn't go to the phone's speaker.
So, are the official ROM updates that repair this? Or, is the cost of going to WM6 the abandonment of BT headsets?
By the way, VoiceCommand 1.6 works fine--if I tell it to stay away from the BT headset.
Pays WM6 Roms
I had the same BT disconnecting problems with my original german Vodafone WM5 and also still have them with Pays WM6 ROMs (2.02 - 2.15) in my Audi A6 MMI.
With the original german HTC WM6 ROM BT worked very well.
Everything else on Pays ROMs is really great. He´s doing great jobs.
Any idea?
I have the same problem with my 8525 and I use plantronics 520. It did the same thing even with other headset too, and also happens in WM5.0, 6.0 and 6.1.
I am tending to believe its a hardware issue, but dont know how to prove it!
ai6908 said:
I have the same problem with my 8525 and I use plantronics 520. It did the same thing even with other headset too, and also happens in WM5.0, 6.0 and 6.1.
I am tending to believe its a hardware issue, but dont know how to prove it!
Click to expand...
Click to collapse
Come On, experts on the XDA portal, no solution?? noooo way!!??
My friend had the same issue with an tytn2 and last schap's rom in french language.
After an hard reset i get BT work fine with his OPEL.
But before i made lot of test desinstalling soft check registery key with no result. I still do know why BT was disconecting woth no reason.
Cheers.
Audi Bluetooth hands free
I had the same problems in wm6 with some roms.
I use the official HTC TyTn wm6 with excelents results, also Schaps 4.31 work very good (No disconection at all).
Now I am using Pay WWE 4.30 with many disconections.
BTW I have the audi TT bluetooth option.
On my 8525 Hermes I use the latest Pays Rom and it was disconnecting all the time (Parrot BT) - BUT then I decided to TURN OFF THE WAN and it improved greatly. Other thing I noticed is that the Hermes has to be in DIRECT LINE OF SITE of the BT device at all times or it is erratic.
BT
It seems there are differences in the WM6 versions. As said earlier in this thread for me original HTC and Schaps WM6 ROM versions are running without any BT disconnections.
Tried several WM6.1 versions now and every single one is working fine with my Audi MMI.
Similar problems handing BT control between applications
Hi all, I've been experiencing similar problems since changing ROMs. Originally with Schaps 3.60a I was able to make a call whilst listening to music all using my BT headphones. The Call would pause the music & resume afterward. It worked great! However since changing to Schaps 4.0, 4.2 & now CRC's PHKv12r9, I've never had the same. On a couple of rare occasions it has all worked fine but more often the bluetooth has to be turned off & back on again to reconnect. it seems to relate to what other programs are also running. I suspect there must be registry settings which control the bluetooth operational modes which are brought into play by the various programs running.

Different Bluetooth Stack?

I've been struggling for several months now to get my MDAC III working with my built-in car Bluetooth hands-free. The full details are below, but in short, I'm told that the system seems to work OK with Wizard, and I'm wondering what about the Wizard could be different to the Artemis (Bluetooth stack perhaps?), and if there is a difference, is there anything I can do about it?
The full issue: The system I'm trying to connect with is in a Land Rover Freelander 2 (LR2 in the US) Initial pairing was a bit hit and miss, but now I've got the the phone paired with the PTI, that's not a problem and they automatically pair whenever I start the car.
I can succesfully initiate or answer a call from the car, but the call itself isn't routed through the car's speakers/mic, it just goes through the phone as normal. However, once in a call if I select the "privacy" option on the PTI (which would normally have the effect I've already got of passing the call to the phone), and then select the "hands free" option, it does what it should and routes the call through the car. Effectively, it's as if the system starts in "privacy" mode rather than "hands free". Once I've done this once, subsequent calls work fine, routing straight through the car, but only until the ignition's turned off. The next time I start the car up I'm still paired, but calls go through the phone again.
If anyone's got any suggestions, I'd really appreciate them.
Thanks!
Try this
Had similar in a BMW...
Try www.jetwaremobile.com
Thanks, did try that but didn't seem to help, it seemed to be more geared towards additional functions like phonebook syncing rather than just getting a working connection in the first place. Maybe I'll give it another go.
Same Probleme On 207
hi,
I have the same ....
I precise that work fine with the original m650 rom, i search many hours but i found nothing, i try bluetooth toggle with no effect...
please help us !
thank for dev for everything they do !
RE
I try many combinaison so:
if i want to use my bt car kit, i'm forced to validate hands free option at every phone call...
I think it's btaudiotoggle the cause of mly problem, he is included in the aje rom...
you think it's possible ?
TangerineTractor said:
Had similar in a BMW...
Try www.jetwaremobile.com
Click to expand...
Click to collapse
Thanks TangerineTractor!
I fixed the problem I have with car kit of OPEL ANTARA using the software you said. It works disable sending Phonebooks.
I am having a similar problem with Wizard Mobile 6 cooked ROM. Before with the official O2 ROM on my Xda Mini S, it worked fine. The car would automatically recognise the phone whenever in proximity, and all calls would go through the speaker.
Now, I have to press the car kit's button (Nokia Bluetooth) each time I get in the car, to tell it to search for devices - i.e. the phone doesn't automatically announce its presence.
So, is there a different Bluetooth Stack we can try?
My Orbit works fine with my Nokia CK-7W using a B&B ROM.
Thanks, and yep that's the same car kit I have.
When you get in the car, do you have to do anything, or does the car kit automatically detect the phone? Mine doesn't since getting the Wizard Mobile 6 cooked ROM.
Do you know what Bluetooth Stack you use, and if I can download it anywhere for the Wizard?
No, just switch on the ignition key and away it goes. Also if the car kit is set as the default hands free if the phone rings it should try to connect to the car kit.
The radio I am using is 2.95.90 I have no idea what bluetooth stack it is, Tom Codin cooked the ROM, he will know.
Okay thanks. Does anyone know if the BT Stack is part of the Radio ROM? If so I'll just try a different Radio ROM.

Bluetooth on WM6 not compatible

Does anyone have a clue why my Vario 2 will connect to my Car Bluetooth when using WM5 (either HTC version or T-Mobile) but when using WM6 it seems impossible to connect?
What happens is this:
When using WM6 I can connect my phone with my (Citroen) car bluetooth and I can scroll through my phonebook using the buttons on my steering wheel. It even confirms I'm using the car BT as a handsfree device.
But as soon as I start a conversation, the only thing I hear trough the sound system of the car is a loud "click" and then only noise.
And the phone is no longer using its own speaker too....
When using WM5 I don't have this problem.
I've tried many things, like the HTC version of WM6, the T-mobile version of WM6, I've tried the Schaps 4.30, I've tried different radio versions. Nothing works.
Anyone any clue?
Riotmanager said:
........I've tried different radio versions.....
Click to expand...
Click to collapse
The bluetooth stack has nothing to do with the radio image, theres no point in changing radio versions.
In the car stereo setup, is your device still listed? If it is....remove it. Then on your device in WM6....scan for the stereo.....if it is found pair with it and can you please reply with the services it offers in the paring dialogue on the Hermes.
I know the radio has nothing to do with the BT, but I was kind of desparate....
When I pair, the only service I can choose is the handsfree function.
Riotmanager said:
Does anyone have a clue why my Vario 2 will connect to my Car Bluetooth when using WM5 (either HTC version or T-Mobile) but when using WM6 it seems impossible to connect?
What happens is this:
When using WM6 I can connect my phone with my (Citroen) car bluetooth and I can scroll through my phonebook using the buttons on my steering wheel. It even confirms I'm using the car BT as a handsfree device.
But as soon as I start a conversation, the only thing I hear trough the sound system of the car is a loud "click" and then only noise.
And the phone is no longer using its own speaker too....
When using WM5 I don't have this problem.
I've tried many things, like the HTC version of WM6, the T-mobile version of WM6, I've tried the Schaps 4.30, I've tried different radio versions. Nothing works.
Anyone any clue?
Click to expand...
Click to collapse
Same issue than you, on a 407 peugeot, I get back on WM5, I work/phone in my car...
I like WM6 news fonctionnalities, I try some Schaps, some CRC, some Black, none were fonctionning...
If anybody has any ideas, I'm ready to try,
Rds,
Well just to update this thing, I have a jabra BT320s which NEVER showed up as wireless stereo, but on the latest pandora kitchen (big storage 3.62 version) it is detected as handsfree and stereo now. Perhaps try that ROM??

Bluetooth pairing process is different, 6.0 vs. 6.1

The device is Holux GPSlim 236. The phone is Hermes. The phone will pair without question on a 6.0 rom, does not matter who cooked it.
It will specifically not pair with 6.1 roms.
I can see the device when scanning for bluetooth devices, i can choose it, it asks me for passcode, but will not accept the "0000" as the passcode. (tried hardware and software keyboards). IF i type in a passcode OTHER than "0000", it appears to pair, i can see the spp slave service and select it, but once the gps software tries to talk with it, it asks to pair again.
Something is definitely different in the pairing process between 6.0 and 6.1.
Any suggestions are greatly appreciated.
Also see thread about it here from the Himelaya:
http://forum.xda-developers.com/showthread.php?t=378103
Thanks,
Rock
Did you select it as a serial port? You have to do this after you pair the device with the phone!
I am not familar with gps units, does it have a pairing mode like a headset? I know with my Plantronics headset, if I let my phone discover it without the headset being in pairing mode, the phone says it pairs with it, but it really doesn't, so I put it in pair mode then turn on bluetooth on my phone and pair up as normal(0000 passkey) and all works fine.
I have exactly the same GPS unit and have no problem pairing it with the probably 15+ WM6.1 roms I have tried.
Try leaving the battery out of the 236 slim for a few minutes and see if that helps. (can't remember is there is another way to reset it)
Bluetooth Pairing with 6.1
In the latest PC Pro magazine in the UK, there is an article on WM 6.1. It says:
"There's another neat feature in WM 6.1, namely that when you try to pair the phone with something like a GPS dongle or hands-free kit that has a fixed PIN, the operating system will cycle through a set of common codes (0000, 1234, 8888 and so on) to try to find the right one."
It goes on to say that there is the potential to get locked out of the pairing if it goes wrong.
I have to say that I have not had any problems pairing with my GPS unit and my car kit, using a number of 6.1 ROMs. Indeed I have seen no evidence of the above software routine trying to pair for me. Possibly, that routine will only appear in the production ROMs, rather than the development ones which we use on XDA Developers.
I had issues with the same device on some roms. I eventually changed BT drivers from WM6 and all went back to normal.
On some WM6.1 roms things went OK though.
Try not using any password when you try and pair it manually.
If it asks would you like to pair your device automatically select no and do it manually.
I was having this problem but WM6.1 does not require a bluetooth passcode for most devices.
mines gps is a holux 240 and i have the same probs
ive mentioned it on a couple of threads, im glad to know im not the only one
im stickin with K's 6 final until this problem gets sorted out
this thread doesnt seem to getting any viewing, so im asking could a mod move this to General Discussion>networking please, it might be sutible there
crusti said:
this thread doesnt seem to getting any viewing, so im asking could a mod move this to General Discussion>networking please, it might be sutible there
Click to expand...
Click to collapse
ummm no, dont move my thread thanks. you can start one over there if you would like.
crusti said:
mines gps is a holux 240 and i have the same probs
ive mentioned it on a couple of threads, im glad to know im not the only one
im stickin with K's 6 final until this problem gets sorted out
Click to expand...
Click to collapse
You are not the only one
I reverted back to the 6.0 and it pairs without issue. I am thinking that alot of these cookers do not pay much attention to the development of bluetooth in some of their roms. Its not like I changed something on the GPS, so something must have happened with the software.... Still investigating. I hope it works on schaps new rom.
miffymiffy said:
Try not using any password when you try and pair it manually.
If it asks would you like to pair your device automatically select no and do it manually.
I was having this problem but WM6.1 does not require a bluetooth passcode for most devices.
Click to expand...
Click to collapse
this method paired my jabra automatically, it didnt even ask if i wanted to do it auto, i juck clicked "pair" and there it was.
When pairing the holux 236 on the other hand, it would ask for a passcode, then reject it if you put in the correct code of "0000". If you canceled it, it would appear in the connected devices list!!, but still ask to pair once the gps application tries to connect. VERY jacked up.
Hissing Syd said:
In the latest PC Pro magazine in the UK, there is an article on WM 6.1. It says:
"There's another neat feature in WM 6.1, namely that when you try to pair the phone with something like a GPS dongle or hands-free kit that has a fixed PIN, the operating system will cycle through a set of common codes (0000, 1234, 8888 and so on) to try to find the right one."
It goes on to say that there is the potential to get locked out of the pairing if it goes wrong.
I have to say that I have not had any problems pairing with my GPS unit and my car kit, using a number of 6.1 ROMs. Indeed I have seen no evidence of the above software routine trying to pair for me. Possibly, that routine will only appear in the production ROMs, rather than the development ones which we use on XDA Developers.
Click to expand...
Click to collapse
Did that article describe any way of disabling that feature? That functionality could easily trick a simple bluetooth device if it is not expecting such a rampage of codes...
rock99rock said:
Did that article describe any way of disabling that feature? That functionality could easily trick a simple bluetooth device if it is not expecting such a rampage of codes...
Click to expand...
Click to collapse
No, there was no mention of if it could be disabled.
Wam7 said:
I have exactly the same GPS unit and have no problem pairing it with the probably 15+ WM6.1 roms I have tried.
Try leaving the battery out of the 236 slim for a few minutes and see if that helps. (can't remember is there is another way to reset it)
Click to expand...
Click to collapse
Wam, which rom are you using now that it works with? id like to download and try it. The 5 or so ive tried did not work.
I power cycle the device without any change in pairing succession.
Thanks!
BTW: Other users experiencing differences between 6.0 and 6.1
http://forum.xda-developers.com/showthread.php?t=391488
http://forum.xda-developers.com/showthread.php?p=2240665

[Q] Opel/Vauxhall CD70 stops Diamond Bluetooth

I have problems with my Bluetooth and the paired device in the car with almost every recent ROM.
After about 10 minutes driving with a connected phone, the Bluetooth shuts down on my Diamond. When I go to Settings -> ... > Bluetooth -> Mode -> Turn on Bluetooth is unchecked. If I check it again it connects again with the phone and about 10 minutes later it's off again.
I went back to the RUU_Diamond_HTC_WWE_EastEurope_1.93.479.3_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe. It's against my feelings, believe, etc. but I want to solve it .....
I installed Advanced Configuration Tool (3.0), went to Bluetooth -> Audio gateway power save and Disabled it. I did it because I was reading about suspended devices and power save features. I thought that the loss of Bluetooth is been caused by a saving power feature.
After a soft reset, the Bluetooth stays connected.
It's a start, but I'm not happy with it ... I would like to use cooked ROM's and optimal settings in the ROM.
There are other tweaks too in Bluetooth, for example the supported bitpool, etc. Perhaps those settings cause the shutdown of a connected Bluetooth device instaed of the power save feature.
Has anyone this kind of problems too with paired Bluetooth devices?
If so, would you like to help me to find the cause?
If not, can you describe what device you use (Jabra, TomTom, car radio, etc.), which ROM, which radio and extra tweaks?
Hi
I do have the same problem. I am using my Diamond with my Opel Astra (Vauxhall) and a CD70 radio with built in handsfree (Opel UHP). It disconnects after 10 minutes and after calls. Everything else works fine. Changing rom and radios has not helped so far. If I don't close the comm manager it stays connected but disconnects after a call because the comm manager is closed with the end of the call. Is there a way to force the comm manager not to close?
Olli
olliver said:
Hi
I do have the same problem. I am using my Diamond with my Opel Astra (Vauxhall) and a CD70 radio with built in handsfree (Opel UHP). It disconnects after 10 minutes and after calls. Everything else works fine. Changing rom and radios has not helped so far. If I don't close the comm manager it stays connected but disconnects after a call because the comm manager is closed with the end of the call. Is there a way to force the comm manager not to close?
Olli
Click to expand...
Click to collapse
I have a CD70 too in a Opel Zafira.
This "comm manager" thing is interesting, but it looks to me like an Opel issue.
Can't you flash firmwares by opel?
Riel said:
Can't you flash firmwares by opel?
Click to expand...
Click to collapse
That's an option, but my Trinity (P3600) performed great with the same car. Will an upgrade solve my problems? I know one thing, it's not cheap either.
I tried it with different ROM's, but it still happens.
I tried it with different radio's, nothing changed.
Till today, I've got now the new radio (v1.05.25.BS14).
http://forum.xda-developers.com/showthread.php?t=432770
It has fixed the delays in GPS + faster GPS fix and more important fo me Bluetooth didn't stop today.
I'm sure 100% sure yet, but seems to be better.
I got something to complain too about the new radio. The radio signal is less strong than the .05 radio.
Same problem here
My Vectra is equipped with CD70.
Previously I've owned a Kaiser and the problem was solved by one of the 6.1 radios, bluetooth connection was rock solid.
Right now I have the same problem with Diamond - after every single phone connection, when I'll hangup, the phone disconnects CD70. When I'll try to reconnect manually using CD70 everything is fine.
I've noticed that the same problem exists when I'm using Nokia bluetooth headset - one call, bluetooth connection dropped...
I've tried following Diamond radios:
.05
.07
.08
.BS14
and two Raphael radios by Bepe:
1.03.25.18
1.02.25.11
Each Diamond radio behaves the same way. Each Raphael radio adds a bonus - random bluetooth connection problems.
Right now I'm back with .05, I think I'll look for the software I've seen once (can't recall the name) - it's a PDA application designed for connecting to the car bluetooth systems and it has been cerftified to work fine with CD70.
Use Jetware Mobile for htc-diamond.
jetware
That's the software I couldn't remember the name.
Anyway I gave it a shot and it gets even worse, I couldnt get the connection lasting longer then 2-3 minutes, totally unstable
Right now I got back to radio .08 - the bluetooth link is rock solid, I guess I'll just need to get used to reconnecting after each phone call
Same bluetooth system in my car, same problems as you guys.
To avoid the disconnections after calls you need to go, with 'Advanced Config' to bluetooth->Audio gateway power save, and switch it to disabled.
For me this little change solve the 'first' problem, but I have another one that I don't know how to solve: the aparently random bluetooth disconections. Sometimes BT is not disconnected in hours, sometimes in days.
I am also using Jetware Mobile, but i didn't feel any improve...
The random ones depend on the radio rom version - I was using .05 and it was rock solid.
I will try .16 with audio gateway started and with power save disabled as you advised - I thought about it earler but previously I tried to disable the power save without enabling audiogateway service
Well, we will see if it works or not.
Hi,
I also have a Vectra CD/70 combination, for 2 yrs now.
I had a HTC3300 and 2years i had not a single problem with Bluetooth connection.
Now i have a HTC Diamond Touch Pro and have the same problems you guys have.
I tried all your suggestions, radio's and so on with no good result.
The good news is .. its an Opel problem and it seems to be that a Bluetooth Firmware Upgrade is available from Opel Germany. I just contacted my dealer and next week he will Upgrade my bluetooth firmware.
I will keep you guys informed.
Hello,
had the same problem with my Opel CD70.
Using Jetware Mobile and limited the entrys who copied to the car to a max. of 5. Also disable the call lists. Now it works.
I think the Opel/Vauxhall Bluetooth Connection disabels if to many entries are copied to the car.
Hello,
any News about our Bluetooth Problem ???
I also have a CD70 from Opel and I cannot understand why my Diamond swich of Bluetooth after a while ?
Is it an Opel-Problem or does anybody now an Application which helps ?
Thanks a lot for Your help,
Stepos
Hi,
I am currently using BTrestore (http://home.casema.nl/rgschmidt/WM/Downloads/BTRestore_V_1_0_0_PPC.ARMV4.CAB). This utility checks the status of the bluetooth stack every 5 secs and (re)enables it everytime it's down. It seems that the 5 secs are short enough to keep the phone connected. It's not a real solution and unfortunately this tool is sometimes instable too, but it absolutely extends the connection time with the UHP.
Maybe bullock can tell us if the carkit upgrade solves anything...??
I also created a ticket at HTC, but they refuse to troubleshoot user specific issues. They told me they only look into issues if they get enough calls from different users and to keep an eye on the update site (they seem to be able to solve issues without knowing what the actual issue is...). So I would encourage everyone here to create a HTC ticket for this issue. I still think it is an HTC issue: a bluetooth stack should never go down without any user intervention.
Good luck!
BTrestart and Jetware Mobile doesn`t help, my Touch diamond disconnect again from Opel CD70 and swiched off Bluetooth !
Can anybody help ?
Sorry guys, the OpelDealer is still "searching" for the Bluetooth upgrade.
After several phonecalls maybe next week (1st week of Febr) it will be made available to the dealer.
Like i said ... i willl keep you informed ... still have this lousy problem !!
..does anybody use the new Rom 2.03 ? Any difference ?
I also asked my Opel-Dealer for an Update of UHP, next week I 'll get new Information....
... well guys I had my CD70 updated !! I am/was very sceptical because the only thing they did was a re-install of the Language of the Navi System with a version 2005 CD. I asked if that was all to correct my Bluetooth problem .... the (smiling) answer was YES.
I have it now for 24hrs ...... and Bluetooth is still on )
I will let you know the result after a week !!
..i can't beleave it works with a 2005-update ! Great !
My Opel-Dealer is still busy in selling 10 Opel Corsa every day (..the magic word is "Abwrackprämie") , so I'll have a date there next week...
When I bought my Vectra the dealer had also to reinstall the Language-CD, maybey it was the wrong version....
...... Sorry guys ......
This update DOES not do the magic trick !! So we have to find another solution
who has the right idea ??

Categories

Resources