Related
I spent a whole day yesterday learning to unlock my new Cingular 8525. Then I tried it using HTC Hermes SIM Unlock v2a, and I followed closely discussion threat between crazyut and pof (http://forum.xda-developers.com/archive/index.php/t-286248.html), but I failed!
Steps as follows: I directly run RUU until ERROR 114 appeared. Then tried to copy HERM_Unlock_v2.exe to the phone, but found that I need to install the software to enable transfer of file from computer to the phone, so I install it. Unfortunately, the installation failed. In Device Manager there is item Windows CE USB Devices, with sub-item: HTC USB Sync(!). There is message: This device cannot start (Code 10). Then I tried uninstall and reinstall, but did not work.
So I use another computer. It can be installed, and connect the phone to this computer, and transfer the file. But I could not run it (I double click it; and also tried to run from: Start, Run, but no response).
Question: (i) Can the phone still be unlock (since the process was interrupted), (ii) Can I continue the process using another computer?, (ii) how can I transfer the file to the phone that can be executed, so I can complete the process.
Appreciate your help.
what bootloader do you have??? one of the first lines in the hermes unlocking thread is this:
It can be used in all HTC Hermes devices, the only restriction is that the device must have bootloader version 1.04
How to enter bootloader can be found here: http://wiki.xda-developers.com/index.php?pagename=Hermes_Resets
there is no need to post the same question in different threads. I have deleted your other post in regards to this matter. Next time make a post in the device specific thread
Many thanks finally a response to my posting (noted also your note regarding second posting - thanks). My bootloader is 1.06.
My understanding is that I can downgrade the bootloader from 1.06 to 1.04 using MaUpgradeUt_noID.exe program, is this correct?
During the process, there is already a message "ERROR 114" as mentioned in Install instruction.
as an FYI you would have gotten a faster response in the hermes upgrading board.. but here is a post you need to read about downgrading your bootloader.
http://forum.xda-developers.com/showthread.php?t=284401
when you follow those instructions make sure you follow #3 as stated.. if its not done as stated you will not accomplish this correctly...
Thank you, I will check and read the info from the link you mention. I.ll get back to you later. Thanks
I have googled the DownGrade_SPL.rar for more than a couple of hours, but could not get free file. All website that I found, we should pay, and some of them $35 - is this really the case? Is there website that can provide free file? Thanks
you dont need the downgrade....
first flash your phone cingular 1.6 bootloader phone with this..it will change your cingular phone to bootloader 1.4..both files are from cingular roms which makes you abe to downgrade your phone from cingular 1.6 to the 1.4 bootloader..understand??
http://forum.xda-developers.com/showthread.php?t=277664
Then follow instructions from here http://forum.xda-developers.com/showthread.php?t=282073
after that you're phone should be unlocked and supercid...
it works.. i have done it to my cingular phone.. just read read and read some more.. everything you need to know is adressed on this website....
Enjoy
honestabe said:
you dont need the downgrade....
first flash your phone cingular 1.6 bootloader phone with this..it will change your cingular phone to bootloader 1.4..both files are from cingular roms which makes you abe to downgrade your phone from cingular 1.6 to the 1.4 bootloader..understand??
http://forum.xda-developers.com/showthread.php?t=277664
Then follow instructions from here http://forum.xda-developers.com/showthread.php?t=282073
after that you're phone should be unlocked and supercid...
it works.. i have done it to my cingular phone.. just read read and read some more.. everything you need to know is adressed on this website....
Enjoy
Click to expand...
Click to collapse
thanks for pointing that out.. i COMPLETELY forgot about that... my head was definitely not in the game last night... Thanks
Many thanks to Shogunmark and Honestable for the advise. I have open the link and it seems that I need to study that first before proceed with thyis great work (e.g. I need to understand how to flash the cingular 1.6 bootloader with ... what file? -apologies for not understand some jargons). Let me also go through the information in the links. And I will get back to you, if I need further clarifications.
Many thanks
Re: Unlocking the 8525
Why not just call Cingu;lar and ask for the unlock code. If your a customer for more than three months, they have to give it to you!
noonrrr said:
Why not just call Cingu;lar and ask for the unlock code. If your a customer for more than three months, they have to give it to you!
Click to expand...
Click to collapse
cause this does more than unlock sim on the phone, this also unlocks the cid on the phone as well...
Hi! I made it!
I learn much from the process. I found the forum has been an exellent site for consultation and discussions. Thanks much to Shogunmark.
All the best for the New Year!
Broto123 said:
Hi! I made it!
I learn much from the process. I found the forum has been an exellent site for consultation and discussions. Thanks much to Shogunmark.
All the best for the New Year!
Click to expand...
Click to collapse
Thats what this whole community is here for! Enjoy your device
First let me apologize for the title of this thread, I really couldn't resist. I just bought a i-mate jasjam and have spent the last several days reading these forums, the wiki, and all the other places that clicking things here will take you. I want to say right out that EVERYTHING I know about the Hermes I learned from this site, and that I am a complete beginner, and please do flame away if i am wrong. I'd rather get insulted online than have a brick in my pocket.
THe one thing that there isn't in the wiki (that I found anyway) is a current, step by step for total noobies like me who don't know what to do first and get scared by dealing with more than three file types in one sitting, that uses the SD card method. It seems that the SD method is faster, easier (especially if you run Vista), and even a little safer that the "old school" RUU method.
Soooo, I'd like to write a new wiki page to this effect, and am more than happy to put in screenshots, links, host file downloads, etc. What i'd REALLY appreciate is if you senior types could take a look at this simple outline and tell me if there is something drastically wrong with it. After a good schooling I'll post a complete article with more copied info from the threads and complete sentences and punctuation and stuff.
PROPOSED "DAY-ONE, JUST OUT OF THE BOX CAN"T WAIT TO" UPGRADE
1.enter bootloader mode to check sp version
2.format an SD card to FAT32, checking card integrity and fixing errors
3.Use Winar to Extract the .NHB file from Hard-SP-v7.zip, transfer to SD card with card reader and rename to HERMIMG.NHB
4.put the card in the phone and enter the bootloader by pressing side OK, Power, and soft reset button (with stylus). Once in bootloader mode accept the upgrade
This safe-nates things up, and CID unlocks the phone, right?
5.re-format SD card to FAT32, checking card integrity and fixing errors
6. Use WinRar to Extract the .NBH from HERM_Radinly_1.41.00.10_CustomRUU, transfer it to the SD card and rename it HERMIMG.NBH
7. put the card in the phone and enter the bootloader by pressing side OK, Power, and soft reset button (with stylus). Once in bootloader mode accept the upgrade
8. check the radio version in system info
9. re-format the SD card for FAT32, checking integrity and fixing errors
10. Use WinRar to Extract the .NBH from WM6 ROM of choice, transfer it to SD card and rename HERMIMG.NBH
11. Put the card in phone and enter the bootloader mode as above, when in bootloader accept the upgrade. Follow instructions from mrvanx for activesync
12. transfer my CAB files for applications to (Temp?) folder on card and then run each of them to install my apps (Skype, CeStar,TengoThumb,etc.)
Does this sound about right? Thoughts? Flames?
Thanks to all for such fantastic work, donations on the way for all who wrote files I have downloaded over the past few days, you guys rock!
whats with the SD card upgrading?
you can run HardSPL by itself, you dont have to extract and put the nbh file on ur storage card.. unneccesarry steps if you ask me..
Midget_1990 said:
whats with the SD card upgrading?
Click to expand...
Click to collapse
Well, I run Vista, and I like the idea of not having to fiddle with the drivers in order to do RUU, and I saw a few posts that some people had difficulty getting things to work with Vista. Also, posts have led me to beleive that it is faster to do it this way, which would lead to less chances of things going wrong (it's really hard to make Vista stop doing things in the background all the time). Also, there are already really awesome guides for doing it the RUU way, but not one for a complete SPL/Radio/ROM upgrade using this method, I think it appeals to a lot of people, including the dreaded Mac user. If it's not actually a good way please do explain, and finally, to me it just seems plain easier. I've only found a few posts that had troubles with the method and dozens that praised it. thanks for replying!!
Madcap, thanks for the input, I was going for continuity but I take your advice, keep 'em coming!!!
oh...you didn't mention Vista in your original thread.. lol .. best advice I can give you ... Throw vista in the trash.
Madcap180 said:
oh...you didn't mention Vista in your original thread.. lol .. best advice I can give you ... Throw vista in the trash.
Click to expand...
Click to collapse
Yep, I ll drink to that
ugh .. u mentioned the D work.. great.. now I'm going to relapse..
Step 4 does not CID unlock the device. It looks like it just installs Hard SPL which will allow the user to recover from a bad radio flash.
Of course this should not matter as there really isn't a need to CID unlock any more (unless you want to unlock/unhide your EXT ROM)
HardSPL just makes your phone Temporary superCID right or something to that effect.
Zzan said:
Step 4 does not CID unlock the device. It looks like it just installs Hard SPL which will allow the user to recover from a bad radio flash.
Of course this should not matter as there really isn't a need to CID unlock any more (unless you want to unlock/unhide your EXT ROM)
Click to expand...
Click to collapse
Cool, it was my understanding that Hard SPL temporarily makes you super CID (as Madcap said) allowing you to flash on any ROM you want, for all intents and purposes is this not pretty much the same thing as unlocking? Not arguing, just trying to clarify. A lot of noobs know that CID is an issue and that they need to disable it somehow when they flash......
Please keep comments coming,Thanks!!!!
P.S. MOD, in my sleep addledness I think I posted this in the wrong place, should it be moved to the UPGRADE forum? THANKS!!
P.P.S. Drinking is the only way I can tolerate having a Vista machine, we all were so happy about getting our new laptops this year, and then we turned them on....it's like getting a christmas present in the shape of a new bicycle, but when you tear off the wrapping paper there's really a tetanus shot inside.
SUCCESS!!
I followed the OP steps (with very minor modification) and was able to go from a completely new, out of the box, never even put in a sim card phone to HardSP-V7, upgraded radio, new WM6 ROM (Schaps, this ROM is awesome, thanks!!!). All without using a cable or upgrading any drivers. From beginning of first download to totally upgraded was one hour. Why anyone would ever do this the old-fashioned way is beyond me, especially if you are running Vista. I'm making a tutorial and have collected the few little things you need to do this and will add a wiki article with pics ASAP.
Thanks to everyone for all the great info and hard work here, a complete noob like me can go from 0-60 entirely by reading this site. I am loving this phone more by the minute!!
A noob who has read the posts and wiki, and then created and tested a step by step routine for others like himself in order to address something that the wiki doesn't.
A fine example that a lot of others should note.
crazyC said:
A noob who has read the posts and wiki, and then created and tested a step by step routine for others like himself in order to address something that the wiki doesn't.
A fine example that a lot of others should note.
Click to expand...
Click to collapse
Yes only thing left is posting in the Hermes Upgrade forum.. ;-)
jompao said:
Yes only thing left is posting in the Hermes Upgrade forum.. ;-)
Click to expand...
Click to collapse
Yeah, i deserved that
mlalahoi said:
Cool, it was my understanding that Hard SPL
<CUT>
P.P.S. Drinking is the only way I can tolerate having a Vista machine, we all were so happy about getting our new laptops this year, and then we turned them on....it's like getting a christmas present in the shape of a new bicycle, but when you tear off the wrapping paper there's really a tetanus shot inside.
Click to expand...
Click to collapse
Sorry man, I just couldn't help myself. I am in love with Vista. No problems whatsoever with it. Have had it installed since it came out and never had to re-install. Speed is the same as when I installed it. Can't say that for XP! LOL. I forget how many times I had to install that piece of........................
LOL
p.s no flames........please.
I love Vista. Its given my two year old laptop a new lease of life.
Hi mlalahoi,
I am getting a lot of issues after installing CE-Start. Played virtually with every WM 6 ROM arround and still experiencing freezing.
Have run Shadow and LVSW without CE-Start for couple of days and both ROMs was very stable and fast. After CE-Start lot of problems.
Will be nice to hear your experience with the Chinese characters
crazyC said:
A noob who has read the posts and wiki, and then created and tested a step by step routine for others like himself in order to address something that the wiki doesn't.
A fine example that a lot of others should note.
Click to expand...
Click to collapse
I'm drinking to that CrazyC - my first couple of posts made me look a total ARSE (But I've learned loads since then...Honest)
marttin said:
Hi mlalahoi,
I am getting a lot of issues after installing CE-Start. Played virtually with every WM 6 ROM arround and still experiencing freezing.
Have run Shadow and LVSW without CE-Start for couple of days and both ROMs was very stable and fast. After CE-Start lot of problems.
Will be nice to hear your experience with the Chinese characters
Click to expand...
Click to collapse
Did you download the 2.8 Suite from the mobem website here AND use thier installer to install TO THE PHONE (install to SD doesn't work)?
I had similar problems when I went through the process of getting my hermes to be dual English and Chinese. THe first time I tried to manually install some cab files I found on a chines forum somewhere, totally jerked my normally very good Shaps ROM. I ended up having to do a hard reset, trying to uninstall the cabs just caused an unrecoverable hang. Make sure you use the official, latest install program and install to the phone, mines been flawless ever since.
Without registering you don't get the dictionary, but you can get a really good free version of CEDICT for mobiles here, it allows you to search by pinyin w/wo tones, english, or chinese characters. If you have trouble getting it to copy-paste between other apps try this app from the Wiki.
I have a collection of good ppc Chinese learning tools, pm me if you want to set up a file transfer, and do check out www.mandarintools.com for all your CHinese computing needs, no affiliation, just a great site.
Hi mlalahoi,
Thanks for the links! Actually I was using all the time v2.8 of Ce-Star, including the original installer - never used cabs to install. I found that "my" version of Ce-Star package is 6KB less than the one you recomended - here might be the problem. During the weekend will flash a new Rom and will play with the "new" Ce-Star 2.8 -- hope it will rock
I am using the ppc version of 金山 (PowerWord) and it serves me well. My Chinese characters needs are very simple ones - to be able to reed text and e-mails in Chinese, and rarely to answer using characters.
Will send you feedback about stability of the ROMs with "new" Ce-Star
Just thought I'd drop this here... Despite how much I read and re-read all the instructions, I mis-understood the two unlockers, and flashed the Alltel ROM on my Verizon XV6900 with the 0.40 Unlocker and wound up with a brick.
Even flashing the Verizon RUU dump wouldn't fix it... SPL 2.01 RGB screen and that's it.
So after much research... MTTY to the rescue. set 16 0, task 8, and viola... unbricked! (I think flashing the verizon ruu first was important)
No storage card needed (or possible on the Verizon, there's no slot!)
Thanks all... still trying to get GPS working now, so far nothing.
vogue_brick1 said:
Just thought I'd drop this here... Despite how much I read and re-read all the instructions, I mis-understood the two unlockers, and flashed the Alltel ROM on my Verizon XV6900 with the 0.40 Unlocker and wound up with a brick.
Even flashing the Verizon RUU dump wouldn't fix it... SPL 2.01 RGB screen and that's it.
So after much research... MTTY to the rescue. set 16 0, task 8, and viola... unbricked! (I think flashing the verizon ruu first was important)
No storage card needed (or possible on the Verizon, there's no slot!)
Thanks all... still trying to get GPS working now, so far nothing.
Click to expand...
Click to collapse
There is a microSD slot on the XV6900. It is on the right side of the phone under the chrome trim. You can see a small SD icon on the side of the phone next to the stylus under the battery cover!
louderjw said:
There is a microSD slot on the XV6900. It is on the right side of the phone under the chrome trim. You can see a small SD icon on the side of the phone next to the stylus under the battery cover!
Click to expand...
Click to collapse
Thanks! I looked all over
vogue_brick1 said:
No storage card needed (or possible on the Verizon, there's no slot!)
Thanks all... still trying to get GPS working now, so far nothing.
Click to expand...
Click to collapse
Not trying to be a flamer here ... but ... you should really learn about your phone stock ... capabilities ... features ... etc. ... prior to doing custom flashes ... especially with the radio ... fortunately for you and me ... it is extremely hard to "brick" a HTC phone ... it may seem bricked ... but I've only ever seen a couple true bricks ... most can be recovered by the heavy hitters here
My point is that you really need to understand your phone and what you're trying to do prior to doing custom roms ... unlockers, relockers, etc. ... this is extremely important when doing radio changes ... fearless and aggressive is no way to approach these changes
And as always .... read ... read ... read ... did I mention READ!!!!!
Again ... not flaming you ... kinda using you as an example so others will learn and maybe keep the number of true bricks to a minimum
Fuzzy
I agree, I got a little excited with this and should have taken my time... My last phone was an Apache xv6700 and I had a blast flashing that and upgrading it over the past 2 years. I rushed into it with this one because I'm an impulse guy and had just bought the phone within 24 hours
me too!
vogue_brick1 said:
Even flashing the Verizon RUU dump wouldn't fix it... SPL 2.01 RGB screen and that's it.
So after much research... MTTY to the rescue. set 16 0, task 8, and viola... unbricked! (I think flashing the verizon ruu first was important)
No storage card needed (or possible on the Verizon, there's no slot!)
Thanks all... still trying to get GPS working now, so far nothing.
Click to expand...
Click to collapse
could you explain how to use mtty! i "bricked" my xv6900 a couple weeks ago too. its stuck on the rainbow screen with the original spl (took a few flashes to get there)! i tried mtty when i did it and there wasnt a usb option in the program! im running on vista. already got my replacement too!
Not sure how to help you... There was a USB entry in the list when I did it, on XP.
On a separate note, I got GPS working and it's incredible.
Nice to see a Verizon user with GPS working!
Mind posting a little guide? I have my Vogue on order right now and want to update it right away for the GPS.
vaxick said:
Nice to see a Verizon user with GPS working!
Mind posting a little guide? I have my Vogue on order right now and want to update it right away for the GPS.
Click to expand...
Click to collapse
Here are the steps I took to successfully get the Verizon hacked with gps:
1. get it hooked up with activesync
2. unlock with imcokeman 0.40 unlocker
(the docs said to flash to the original rom here, but there is no verizon ruu, and my phone auto-reflashed itself anyways and ran customizations)
3. unlock with imcokeman 2.31 unlocker
4. install the alltel RUU (should be in sticky thread)
5. download Build OS from ppckitchen.org and use the updater to get the vogue 6.1 gps 3.02 kitchen
6. pick options and build, flash..
fire open google maps, pick menu->use gps.. magic.
It helped me out of a jam tonight, lost in bumblefukk and found my way back with it.
could you please explain in step-by-step detail as to how you unbricked your xv6900?
I'm currently working on my friend's xv6900 (TyTN II user myself) and unlocking and flashing roms on this phone is so different (yet kind of the same?) and I'm now at a point where I'm stuck at the HTC startup screen and thats about it. where did you get MTTY and how exactly do you use it? I tried downloading one but it was a very old version (2001) and I'm pretty sure that it's not the one you were using.
if anyone else knows how to unbrick this phone please chime in thanks a lot!
vogue_brick1 said:
Just thought I'd drop this here... Despite how much I read and re-read all the instructions, I mis-understood the two unlockers, and flashed the Alltel ROM on my Verizon XV6900 with the 0.40 Unlocker and wound up with a brick.
Even flashing the Verizon RUU dump wouldn't fix it... SPL 2.01 RGB screen and that's it.
So after much research... MTTY to the rescue. set 16 0, task 8, and viola... unbricked! (I think flashing the verizon ruu first was important)
Click to expand...
Click to collapse
Can you explain what you did after MTTY? I bricked mine, got stuck in the SPL 2.1.1000 bootloader, used MTTY, got it unbricked, but now am stuck at the leaked sprint rom's splash screen. Any help would be greatly appreciated!!
Hi amm
I am new to windows mobile. i got this ophone of my old work mate.
I have tryed to put windows mobile 6 on the phone as it only have wm5 on it, but i get as far as the phone changing to upgrade mode ( 3 striped red, blue and green) screen and then it says that the phone cant comunicate.
I have tryed going though o2 website but it not recignizing my serial for the phone ( ex contract and also was a replacement handset)
any help would be nice, by the way i am on windows vist a, but i have also tryed it on xp, but the same still happns.
Thanks
Paul
anyone? noow any suggestions
This answer may seem condescending, but it isn't.
1. Are you attemtping to flash a rom update from the phone's original carrier or a non carrier specific rom? If a non carrier specific rom then see #2. If carrier specific did you download the rom from a secure place such as the carrier's website? If not, you may want to and try again.
2. Have you made sure your phone is CID and sim unlocked? This has to happen if you are attempting to flash a non carrier specific rom onto your phone. There is literature in your specific phone's Mobile 6 forum that is stickied or in the Wiki which will show you the best way to accomplish flashing. You must first read, then use the correct methods and tools or you will most likely create a brick. At this point of the game your phone is a little older and the path to Mobile 6 is well laid out. Which leads to the next question.
3. Have you done a search for this problem? You are not the first and will not be the last to have run into this issue. Using the search button does wonders here. If you have the cajones to flash your phone you are adventerous and the knowledge you will pick up will help in the long run. I say this because flashing is addictive and once you see the immediate improvements you will continue to look for better roms.
4. Please remember this is a developer's forum so the intelligence level is higher than most other forums but the patience level is much lower for those not willing to follow directions and/or help themselves. Some things have well laid out paths and others are trial and error. A lot of people here are doing a large amount of work for little to no money so please READ before embarking on your journey.
5. Get to work. Oh yeah. Please lit your phone's information in your signature. It will save someone asking the first 2 or 3 questions I did everytime. You could use mine as an example. Believe me it saves time and people are more willing to help.
hey thanks for your message
I am trying to flash the phone with Official O2 UK WM6 Trion (Hermes) rom 3.54.206.1_6275+radio 1.47 (3-8-2007) , the phone is simfree.
but even on trying to install Olipro v7 2.10 i get messages like 266 or 260 conection timed out or something. i am technical minded and i have tryed to serch for the awsers using google.
I suggest reading the Wiki and your Mobile 6 forums for the way to flash without using the usb cord. It will take a non-sdhc memory card and uses the nbh file from the rom you are flashing. Research that.
What is the HTC name for your phone? The Trion is a Hermes or a Wizard correct?
Also, CID and sim unlocking your phone will eliminate many future problems. Just be aware it automatically voids your warranty.
Okay - can you do a soft reset and have the phone work fine? That is step one. If so, then go to the Hermes Mobile 6 forum and check out the stickies. Dr. Puttingham wrote a great guide to flashing our phones.
If you can't get the phone working from the soft reset I suggest reading the Wiki and the Mobile 6 forums for the way to flash without using the usb cord. It will take a non-sdhc memory card and uses the nbh file from the rom you are flashing. Research that.
The Trion is a Hermes, which is what I have (Cingular 8525). I would suggest a non carrier rom of Mobile 6.1. You will find it to be much faster and stable.
Also, CID and sim unlocking your phone will eliminate many future problems. Just be aware it automatically voids your warranty.
hi i just found out that thephone is not a trion afterall it is a xda mini s, can this still be upgraded
I believe the Mini S is a Wizard. check out the forums. All the answers are there. I retired my Wizard 3 months ago . This is an easy problem to fix. Just read. I still suggest Mobile 6.1. Especially on the Wizard.
Like the title says this is my virgin flash. So what do you guys think should be my first ROM? I've looked at a bunch.
Looking for stability and style.
Just to get this correct I need to unlock my phone even though it's att and I'm using att. (Should I just unlock the CID or both)
Then I need to install HardSPL 7.1?
Then flash the ROM I choose.
Then load APPS as needed?
Thanks for the help!
Hardspl v7 http://forum.xda-developers.com/showthread.php?t=296722
I would unlock and supercid http://forum.xda-developers.com/showthread.php?t=293665 then I ran hardspl again just to make sure, because unlocking changes the bootloader.
Then you should be good to go. Hardspl will help you in case you get a bad flash or bad rom, it's easier to recover. Supercid will allow to flash unsigned code (custom roms).
Looks like your on the right track, I'm just not sure where you got v7.1 for hardspl? That's why I included the links.
Also, "any rom you choose", but only from the Hermes forum. Flash a rom for another device means instant brick and you may not be able to recover it.
Hard SPL is a safety net only, there are NO guarantees you won't end up with a permanent brick, Hard SPL or no...
Most times you have to do something REALLY dumb to end up with a total brick but there is a miniscule chance, especially if you are playing around with the radio rom.
Happy flashing...
It was late last night and I couldn't remember if it was 7 or 7.1 lol. I'm charging the phone now. Gonna make sure it's nice and full then I'm gonna give it a shot. Thanks to you both for the help. I just needed to hear I was going about this the right way. I think I'll try one of Schaps ROM's first then try one of Josh's and see what I like about each. I've only got about 50 pages in on each so I'll read alittle more while the phone is charging. Thanks again!!
Oh wanted to ask also is there a Page or sticky just for Apps, skins, themes, and such or do I need to know what I'm looking for and search it?
Dang I thought my other phone had a microSD card in it.....turns out it's M2. Guess I'll stop on the way to work to pick one up. Non SDHC 2gb or less! Another question when it states now copy this to your phone....What file do I copy it to? (I'll head back to the Wiki and see if I can find that myself but figured I'd ask).
copy the RUU_signed.nbh and rename it hermimg.nbh the exe file is the flashing utility, and you don't need it if your flashing via the sd card.
make sure the card is formatted as fat32 (not fat).
Ok I did it the RUU way without the SD card. I'm now at 2.10.01 so I'm good. Now off to work and will hit the unlocker next. Thanks for the help!!
Ok unlock has been completed now I'm going to run Hardspl again. What about the radio I see that is has changed. Should I change that back to what it was at some point?
Ok I've done my first ROM flash wow! I grabbed Schap's WM6 Pro 4.31. I'll try it out and see if I like it. If not try another. Thanks again for helping me thru!
If you wish to risk changing the radio, do so but only if theres a problem. If the radio rom flash is interrupted, you will almost certainly have a brick on your hands.
Use the sd card method to flash so you then minimize the amount of problems you may have.
Remember though, if the radio rom is working fine, don't touch it....
Cheers...
boog321 said:
I would unlock and supercid http://forum.xda-developers.com/showthread.php?t=293665 then I ran hardspl again just to make sure, because unlocking changes the bootloader.
Click to expand...
Click to collapse
Hard-SPL makes your device appear as SuperCID... it's all you need.
vp3G said:
Hard-SPL makes your device appear as SuperCID... it's all you need.
Click to expand...
Click to collapse
Ah, cool! Thanks, vp3G! I guess I took all the info wrong. Reading the 2 threads it wasn't clear. I guess my method worked though! haha
Yea, it's all quite confusing... Hard-SPL ended up negating the need to use pof's unlocker. Olipro is a friggin' genius (as is pof).
So all I needed to do was Hardspl and I would have been good to go? I have another hermes I'm doing for myself. I do find I'm not getting very little service if not none at all in the house. I use to get 3 or 4 bars. Should I change the radio? Does the radio change with each ROM loaded?
You can try going back to the radio that you originally had, just do it the sd method to minimize the chance of something going wrong.
You could compare the difference between the 2 hermes.
vp3G said:
Hard-SPL ended up negating the need to use pof's unlocker).
Click to expand...
Click to collapse
True, but if you wish to sim unlock then you still need Pof's unlocker.
I have to admit I'm getting there myself LOL. It really isn't that hard after you do it the first time. Some things I got stuck on (Pure newbness).
Some ROMs are compressed with .rar and .7.....I found you must download a unzipper/compressor to extract the files you need. I used Winrar some use 7zip. I'm getting there. There is soooo much info on this site. You find that you search for an answer and you get a page of answers with 3 different ways to do it LOL!
We have all been there at one point, too!
When I first brought my hermes home and it was still locked to the at&t network, I was so worried I was going to break it.
Lots of reading, and lots of tinkering later, and I am working on my own rom. Granted, I didn't port it, but I have done so much tweaking that I don't think anyone could tell where it came from.
Funny thing is, I still keep learning so much more. I think it's like my other hobby, ham radio, I don't think anyone can try everything! It seems to go on and on.
Ya know you gotta love the internet LOL. I've learned about so many things (mostly due to them breaking lol). Here's another question for you guys. For those who have Josh's 6.1 ROM. Where is the lock unlock button??? I see the lock device setup for password protection but I don't see a regular lock the screen so I don't make but calls button. LOL I'm gonna try to load his S2U2 thing when I figure out how to do it.
You can add device lock to the today screen under settings>today (at least it should be there), but if your using manilla I don't have a clue lol