Another ODD battery problem - 8525, TyTN, MDA Vario II, JasJam ROM Development

Since I have upgraded to WM6 with the official ROM release for AT&T I have been having odd battery issues.
I forgot to charge my phone last night but when I left the house this morning it showed 40%.
I stream audiobooks from my phone to my car stereo via Bluetooth and less than 10 minutes into the drive I received a low battery warning. By the time I got to work which is about a half hour drive the phone switched itself to airplane mode and then powered down. I could not get it to come back on until I plugged into my PC at work and then it booted so it had been fully shut down.
I have noticed at other times that the battery level goes from a high number to a low number VERY quickly. It also seems to charge very quickly and can go to a full charge from a USB connection in just about 2 hours.
Anyone else see this? It was a very steady reliable discharge rate under WM5. I have seen others talking about the OS potentially mis-reading the battery level but have seen nothing conclusive. I think perhaps it is just not updating the actual battery level when it should so when I see it at 40% it was really very low and just had not updated.
Anybody else???

I havent had my phone for long and flashed it immediately to Windows Mobile 6, but what I have noticed is that it charges pretty fast and I just notices just now that if I turn the phone off while still plugged in for charging but the charge indicator on the phone was green when it was on changed to orange to indicate charging when I turned the phone off. So maybe there is something at the software level affecting the charging process as turning the phone completely off allows me to charge even further than when the phone was on.

What has worked for a number of people is to let the phone get to 0% battery so it shuts the GSM off and then itself, then plug it into the mains charger overnight. This seems to have the effect of re-calibrating the battery meter. I have no idea if this actually works or if its complete coincidence but a number of people in various Schaps threads have had success with this. There is also the possibility that your battery is just screwed. Most of us I assume have devices that are a year or more old and mobile batteries dont last very long especially in power hungry devices like the Hermes.

Another battery Observation!
I have experimented with 3g off al day, and only E (Edge) was displayed on top. 12 hours, 5 phone calls equal to 36 minutes total, I had 60% left on battery. Same hours, 5 Phone calls, with 3G turned on, 42 minutes of conversation, one email sent, 5 received, battery displays 90%. I believe EDGE is what consumes power and drains the battery. leave on 3G and your battery will indeed last longer.

WM6 Battery Life
johnny13oi said:
I havent had my phone for long and flashed it immediately to Windows Mobile 6, but what I have noticed is that it charges pretty fast and I just notices just now that if I turn the phone off while still plugged in for charging but the charge indicator on the phone was green when it was on changed to orange to indicate charging when I turned the phone off. So maybe there is something at the software level affecting the charging process as turning the phone completely off allows me to charge even further than when the phone was on.
Click to expand...
Click to collapse
I have noticed at home that when I plug it in to my Linux box (no synching of course) the charge light comes on briefly then shuts off and may come back on after about 10 seconds. I suspect in my case it may be the cable going bad but it only just started since the WM6 upgrade.

WM6 Battery Life
asfoor said:
I have experimented with 3g off al day, and only E (Edge) was displayed on top. 12 hours, 5 phone calls equal to 36 minutes total, I had 60% left on battery. Same hours, 5 Phone calls, with 3G turned on, 42 minutes of conversation, one email sent, 5 received, battery displays 90%. I believe EDGE is what consumes power and drains the battery. leave on 3G and your battery will indeed last longer.
Click to expand...
Click to collapse
After a full charge yesterday afternoon I used my phone for a bit of reading an e-book for a half hour, 40 minutes listening to audio streamed via Bluetooth yesterday afternoon and another 40 minutes on the drive to work this morning and the phone is down to 50%. Wifi is disabled and I had no phone calls in that time. The only other usage is it automatically updating calendar and contacts with my exchange server but only every 4 hours ending at 6:00pm so that is not a big drain.
I have the device set to shut off the screen after 3 mins inactivity (not just backlight) but the battery drain seems to be much faster than it was with WM5. Perhaps it will straighten itself out with a few discharges and re-charges.

Related

Battery Charging Issue

I have a wierd issue on the new purchased TP2.
I am recently I owner of Tytn II, just switched over to TP2. Once I received the TP2, it came in a full battery status. Then I used it all up and then proceed to my 1st charge ( over 12 hours, with phone off)
Things happened after I woke up in the morning.
1. No lights on for charging ( I assume that's a new feature when battery is full, instead of charging when red )
2. once I turned on and shows only 45-50% of battery status.
So I used it all up again, and see if it charges on the this time.
I am just wondering if anyone have this charging issue.
Dude, you are not treating your battery correctly. The below link has some useful info. Especially the link in post 3 by Sjuust.
http://forum.xda-developers.com/showthread.php?t=524393
Btw, when it's charging, the status light will be a solid amber. When fully charged, it's a solid green. If there's no light, check your wires and stuff. Perhaps it's a bad socket.
Just doing a follow-up on the issue, the 2nd time not successful too
I tried and it worked only when I turn the device on to get a full charge.
Anyone think it's weird
Seems you mini usb does not connect propper. Try another cable, if this works you know the problem.
Or: press the male side of the mini usb each direction until you see a light burning. If this happens the usb opening in the phone is broken and you should get it fixed.
If this all does not work, still get it fixed. It's probably not the battery, but the usb opening in your phone.
D810Noob said:
I have a wierd issue on the new purchased TP2.
I am recently I owner of Tytn II, just switched over to TP2. Once I received the TP2, it came in a full battery status. Then I used it all up and then proceed to my 1st charge ( over 12 hours, with phone off)
Things happened after I woke up in the morning.
1. No lights on for charging ( I assume that's a new feature when battery is full, instead of charging when red )
2. once I turned on and shows only 45-50% of battery status.
So I used it all up again, and see if it charges on the this time.
I am just wondering if anyone have this charging issue.
Click to expand...
Click to collapse
that is very unusual as when phone is fully charged it stays on constant green light(led). at no time should it go off. unfortunately your battery may just need a few more normal charging cycles to achieve its full potential. if the led light goes off that is another issue! have you added any battery customizations?
Same problem here
I have - more or less - the same issue as D810Noob. My TP2 came fully charged out of the box. First time I charged it, the amber light was on during charging. Next morning no light was shown. I am not sure, but as I recall it, the battery was 100% charged. In the recent days, after one night charging (phone switched off) the green light is being shown but battery meter shows 89% (yesterday) or 91% (this morning). I have the 1% increment battery driver installed with the greenbatteryfix-icon installed.
This morning, after having switched on the phone and after having been confronted with 91% charge status, I reconnected the phone to the charger until it reached 100% (left the phone on during charging). With only two calls of two minutes in total and gprs (no hsdpa) running for two mail accounts, battery status dropped two 80% in 5:30 hrs. Never had such a drain with my TYTN2 that had (more or less) the same configuration.
It may very well be that my battery is not (yet) calibrated correctly, albeit that I fully discharged it last night. I will redo this a couple of times before returning to the shop, but this needs to be improved otherwise I will go back to my TYTN2.
Cheers, Dela
Still having this issue. I have drained my phone completely yesterday evening until it switched off itself. Ten restarted until it switched off again. Then had it charge for forteen hours (phone switched off). When I switched on the phone this morning, battery meter showed 96%. A bit more than an hour later it shows 80%. Had no phone calls, only receipt of six emails and half an hour drive in my car with BT connection. BT is on continiously, BTW.
This does not look good, does it? Anyone who can shine a light on this?
Cheers, Dela
PS: the charging light was green when I took it off the charger this morning, whilst the battery meter showing the 96% charge status right after the startup.

Battery Problem

Hi. I have a Voda branded TP2.
I have installed the 1% battery indicator and have realised that the battery is dropping at an alarming rate. In two hours without any data activity, just two calls of 5 mins each and the battery has already reached 74%. The number drops in front of my eyes. Quite scary actually.
Anybody else faced a similar porblem?
2 things I can advice you (as a TP2 beginner)
-First times: charge up to 12 hours non-stop even when light is green (has nothing to do with phone but with the chemical proces inyour battery) this will prolong lifetime
-This TP2 WWE ROM has a lot (and I mean A LOT!) of background running stuff compared to other WM 6.1 - ROMS. So you thing it is not using any current but it is!
Maybe you could install advance task manager and check out all running programs and processes ...
hope this helps ...
greetz,
Kjoere
Thanks. I have done the 12 hours charging many times - about 6-7 times. Will try the advanced task manager.
Anybody else with a battery problem?
Any application / software is known to be a battery drainer?
Thanks
Had a strange one last night. Went to be, put the phone on charge (was about 16% iirc), and the orange light came on to say it was charging. Then, this morning at about 3am, I hear the phone making bleeps. Check it out, and it's at 5%, with orange light flashing. Take out charger, put it back in, and it starts charging. I went out afterwards, came back about 4.30, and it says it was about 80% complete. Go sleep, wake up about 7.30am, and it's fully charged (green light). Then, I unplug charger, turn on, and it says 96%, and I notice it dropping the amount of charge in front of me (like OP's notice), until it got to about 91%.
Now, about 5 hours later, it reckons the charge is 74%. So dunno why it went down so quickly, and why it didn't actually charge... But will keep my eye on it and see how it goes...
data connection
Another way 2 keep your eye on it: check data connection (start>settings>connections>comm manager) a lot of stuff open this connection which uses power. if it turns on without you knowing .... (especially auto-update plugins (weather?)), sometimes AS also ...
gr
C.
For indo, it says here (amongst others)
http://forum.xda-developers.com/showthread.php?t=519673
that it isn't a good idea to do "old style battery cycling"
I really don't know what to think of LiPo battery management, so many different theories.
Also, something that annoys me is that I fully charge the TP2 overnight, in the morning the lights green. If I simply unlug charger and plug in back in it well go back orange and stay orange for a good half hour... and I can start again a few times...
To be honest, I had to hard reset my device couple of times and haven't had time to 'fully' recharge it after the resets.
I guess I will give it a few days of full charging and then check on the battery.
But, I am not joking when the 1% battery meter just drops numbers faster than a meter at the gas station.
vinayaksupekar said:
To be honest, I had to hard reset my device couple of times and haven't had time to 'fully' recharge it after the resets.
I guess I will give it a few days of full charging and then check on the battery.
But, I am not joking when the 1% battery meter just drops numbers faster than a meter at the gas station.
Click to expand...
Click to collapse
I had this problem when I have push mail turn on. If you disable push mail and set it to receive like every 15 mins, it save the power a lot.
Try the advance config to auto disconnect every x mins, this will helps as well.
Hi HaveryR and others,
yep your source isn't to bad. Beginning with full charges (6 to 12 hrs instead of 3 like the manual says) isn't about the old charge-memory story (because Lithium-Ion battery don't work this way, only the nickel-cadmium and nimH do) but about fully charging cells.
I mean the best way to look upon this is like a pile of bricks on top of each other (all different cells if you wish). So the first time it is important to give all the bricks enough time to charge - so even when it says 100% it does not mean that it has (you're indicator is a feedback of a reading by your cpu). So not all the bricks (let's say) have the same quality (yesyes even in this day and age of hight teck).
So you can also take this parallel to discharging: if you discharge fully, you risk that one of these bricks get busted and so will NEVER recover.
So i agree on this with your source a LiOn batter is bettery served with frequent partial charging and must NEVER be drained completely
Greetz,
Kjoere
Guys,
I put the TP2 on for charging the whole night (about 9 hours). In the morning the LED was green and the battery meter said 100%. I took the charger off from the handset and re-inserted the tip in. Guess what? 95%.
AM not sure if it is a battery problem or handset problem?
Its come down to 73% with just one phone call of 5 mins. Mail is on, but its on manual and havent pulled anything since morning.
Any idea?

Battery re-calibration??

This started on suiller's ROM guide, but I feel it's really OT so I should take it outside.
I've had battery issue ever since I got the Diamond. With moderate use (maybe ~15-20min of call per day, email check every 30 min, moderate web browsing) the battery level can drop by ~ 15-20% per hour on average. This means the battery would only last 5-6 hours without charging, which is not good enough to last through a day.
I first looked at whether the phone has any serious battery drain application, and it doesn't. With BatteryStatus I see the battery drain is ~ 100-150mA with GSM on, BT on. When I'm downloading email, or browsing the web, it does go up to 200 ~ 300mA briefly, but that is only when it's transmitting / receiving data. In standby mode with screen off it drains less than 50mA. These numbers seem pretty typical from my experience.
And here's the weird thing - on a typical day, when I wake up, and take the phone off the charger, it can drop from 100% to 93% within 30 min. On the way to work, when I would browse the web lightly, it can easily drop from 93% to 80-85% within an hour. That's pretty bad battery life.
Yet there are instances when I've been browsing the web, or playing MP3, or using YouTube for a good 10-15 min, but the battery level would not drop.
I figure maybe the battery needs to be re-calibrated, so I decided to discharge the battery and recharge it. I know this doesn't help improve the battery life of LiIon batteries, but I was trying to recalibrate it.
What happened, when I was discharging the battery, was I found the battery drop was very quick from 100% down to ~ 50%. From that point on, the battery drop is much slower.
And from 50% to 25% the battery seems to last forever. The most interesting thing is with the battery down to 15%, I did a lot of 3G web browsing, listening to MP3's, turn wifi on, and that 15% of battery lasted a good 3.5 hrs with heavy use until it's so low the phone stopped working.
The whole discharging process ended up taking 10 hours, and that's with HEAVY use for the last 3-4 hours too. That's actually acceptable for battery life (not great, but at least it'll last me through a day outside with moderate use) and obviously doesn't jive with the 15-20% drop per hour when I'm operating in the 50-100% full range.
When I'm charging the battery, I also noticed the level went up from 0% to 70% very quickly ... pretty much over 40 min. BatteryStatus shows it's being charged at +600-700mA.
As the battery gets full, the charging is much slower ... BatteryStatus shows it is charging by ~ 100-200mA only.
With the battery level up to 99%, it took almost forever to finally get up to 100%. I think it took at least 20 min.
So after a full discharge - recharge, I used my phone as normal this morning to see if it's been calibrated, but nope. It still drops from 100 to 93% within minutes of doing virtually nothing, and easily drop to 80% after an hour ride to work.
Does your battery perform the same way? Should I replace my battery? Or is there a way to properly calibrate the battery?
btw location and reception has nothing to do with it. I have good to excellent reception throughout this test.
I'm having the same problem but not with every rom (don't know wich ones, tested almost every rom hero) So is this a piece of software wich shows the live that doesn't work ?? or is it the battery ? As i can see it it's depending on rom thus it's not hardware
But hey I'm n00b
i've noticed that a soft reset or power up will use 3-7% of battery depending on the weather (what else could it be )
don't have the ability to discharge but i agree that in many cases the battery usage drops drastically & there is no reasonable cause
hope someone can figure this out!
From 4pda.ru
http://4pda.ru/forum/index.php?showtopic=85754&st=100&p=2338080&#entry2338080
1. discharge the battery completely (by playing video, audio, etc.)
2. Remove the battery and wait about 1min then place it back (do not power on the phone)
3. Full Charge the phone, wait when LEDs stop blinking (do not power on the phone)
4. When fully charged - remove the battery (do not power on the phone)
5. Wait about 1min then place the battery to the phone and now you can power it on.
If battery is more or less OK it will re-calibrate.
I hope it will help!
STM123 said:
From 4pda.ru
http://4pda.ru/forum/index.php?showtopic=85754&st=100&p=2338080&#entry2338080
1. discharge the battery completely (by playing video, audio, etc.)
2. Remove the battery and wait about 1min then place it back (do not power on the phone)
3. Full Charge the phone, wait when LEDs stop blinking (do not power on the phone)
4. When fully charged - remove the battery (do not power on the phone)
5. Wait about 1min then place the battery to the phone and now you can power it on.
If battery is more or less OK it will re-calibrate.
I hope it will help!
Click to expand...
Click to collapse
Thanks. I tried those steps yesterday and my phone is pretty much behaving the exact same way after the battery cycle.
After all the steps, the battery shows it's 100%. I unplug it, and it drops to 97% within MINUTES literally. Now I plug it back in, and it takes forever to get from 97% back to 100% (> 1hour)
I think it may be a battery problem and not a calibration problem. The drain averages ~ 120-150mA when phone on, screen on, no data, and below 100mA with phone on in standby mode. That seems pretty typical? I'd think the battery should last longer than 8 hours (till it completely dies) in that case.
Where do you guys suggest I buy a new battery for the Diamond (other than HTC directly)? I bought one from DealExtreme but the battery runs ~ 10C hotter than normal all the times ... I don't think I want that as my primary battery.
If you get through a full day with moderate-heavy use on your battery, I say that is normal and good battery life on a Diamond. So, why bother that the percentage is not proportional? I would not get a new battery for this since the problem is only in the reported percentage, not the battery life itself.
I've had plenty of cars that went from full to half tank on the meter significantly faster than from half to almost empty. You know about it and adapt to it, simply.
Hello !
I'm understand you, i have a ELF (Touch P3450), and a Diamond, the same problem appear for the two phones!
Every Morning, when i disconnect from charge my diamond, my level battery go to 93% in 10mns without reasons (One sms, no 3G, no Wifi etc).
My battery go down to 50~70% around 14H (2H pm), and stays at this level for many hours (4-5hours ~), i think it's not a problem with our battery, but a dysfunction of the sensor battery, which shows wrong data =/
By the way, that problem doesn't appear every day, for example, today my battery has that level : 83% (15h43), so today it has a good level.
Since i have flash that ROM : http://forum.xda-developers.com/showthread.php?t=521941, with radio 1.13.25.24, i have less less issues with my battery, it's more stable!
That's all, hope that helps you.
Ok guys, I've made a few discoveries that I figure I could share with everybody. Maybe you'll find it useful.
Last week I went on a trip and turned off the data connection while I was out of the country. Instead of letting the roaming charges kill me, I was relying on wifi to check emails and browse the web.
I ended up checking emails just as often, because where I worked had wifi AP.
Now, I could usually get 8, maybe 9 hrs out of my battery with moderate use before it's completely empty previously. So I was very surprised to find that with a similar usage pattern, but using wifi instead of EDGE/GPRS I still had 30-50% battery left at the end of 8-9 hours day everyday during the trip. I know data uses a lot of battery, but I always thought wifi drains even more, so that's quite a stunning discovery.
Now, I don't think it was due to wifi draining less than GPRS/EDGE (can't be true), so it must be something else. In trying to figure out what made the difference, I did a bunch of tests after the trip, and this is what I find-
1. Data channel dis-connection / re-connection is BAD
I used to always set my phone to auto-disconnect data channel (EDGE/GPRS) after 5 min of inactivity, in an attempt to save battery. What I found, was keeping the data channel open does NOT actually drain more battery than leaving it off at all. Transmitting data drains battery, but not leaving the channel open. However, disconnecting it, and re-connecting it all the times actually drains quite a bit of battery. I set my phone to check email every 30 minutes, and then there's also the odd weather forecast that needs data channel. In a 9 hrs day, that means channel disconnection + reconnection of about 40 times.
The last couple days I have left my data connection ON all the times, and I actually get more hours out of my battery. My battery used to drop ~ 10-15% per hour with moderate use. By keeping the channel on all the times it's been kept to under 10% per hour!!! I've only tested it for a couple days. I'll report more on it once I get to test it for longer, but the idea that 'keeping data connection off when you're not using it to save battery" seems to be a complete myth. The opposite actually saves battery!!!! And as a bonus, I don't even have to wait for the data channel to connect when I need it!!
2. Recycling the radio is VERY BAD
Everybody knows 3G is a real battery killer. However, similar to EDGE/GPRS, keeping the 3G channel open does NOT drain any more battery than turning it off, or turning on EDGE/GPRS channel. When the data channel is idling, it doesn't matter whether it's on EDGE, GPRS, 3G, or even completely turned off, the battery drain is close to zero in all cases.
Now, you do see a 1.5 - 2 times battery drain with 3G compared to EDGE/GPRS, so I've always turned 3G on only for web browsing or watching YouTube, and use GPRS / EDGE for regular emails update. The thing is though, if you're not transmitting much data (which you won't for regular email update), the difference in battery drain is minimal. SWITCHING between 2G and 3G though, requires a radio power cycle (turn off then back on to switch frequency) and THAT drains a lot of battery!!!
So if you're often switching between 3G and 2G, and you only transmit little data in 2G mode, you might actually be better off keeping it in 3G all the times instead of forcing the radio to power-cycle all the times.
I've tried keeping it in 3G all day long and I noticed minimal increase in battery drain. However, there might be another reason you want to consider - RADIATION. 3G not only drains more battery than 2G, it also transmits at a stronger power than 2G and as a result create more radiation. For that reason, I'm still keeping my phone to 2G for email updates and what not, and switch to 3G only for web browsing. For radiation you may try this thread if you want to read more about it.
3. VGA screen is a REAL battery killer
I do quite a bit of reading on my phone (ebook, on-line magazines etc) and reading ebook was never a battery concern in my days with the Touch (QVGA screen).
That's why I was quite surprised on the Diamond, reading the ebook for 1 hour, with EVERYTHING else turned off (GSM, EDGE, GPRS, 3G, BT, wifi), my battery level went down by 12% in ~1 hour.
The VGA screen drains a lot more battery than the QVGA screen. Now, if you need to use the phone you need to use the screen, there isn't much of a choice. It does make sense, however, that if you're using the screen for a while (like reading ebook) switching from a high brightness level to a lower brightness level.
Oh, and the auto-adjust brightness thing? That doesn't help you save battery at all. This is because it polls the light sensor every 2 sec (default value, but you can change it) and adjust screen brightness accordingly. This mechanism drains battery in itself, and in most cases end up using more battery than keeping the brightness constant at a low to medium level.
The auto-adjust thing is cool, and in theory it sounds like it can save you battery, but unless you constantly set the brightness to max even when you're in a dark environment, disable the auto-adjust and just set it to a constant 50-60% instead.
These are the few things I've noticed and I'm still trying things out, but over the last 2 days I've seen a significant drop in battery drain. I would be lucky to go through a 8-9 hrs day with moderate to heavy use before, the first 2 days I tried this I still had 60% battery left after 5 hrs of moderate use. The Diamond is very weak on battery life so every bit helps! I hope these tips are useful to you!
Thanks for your share
number16 said:
When I'm charging the battery, I also noticed the level went up from 0% to 70% very quickly ... pretty much over 40 min. BatteryStatus shows it's being charged at +600-700mA.
As the battery gets full, the charging is much slower ... BatteryStatus shows it is charging by ~ 100-200mA only.
With the battery level up to 99%, it took almost forever to finally get up to 100%. I think it took at least 20 min.
Click to expand...
Click to collapse
It's exactly what the charging process is supposed to do.
Read more here:
The charge time of most chargers is about 3 hours...
Increasing the charge current does not shorten the charge time by much. Although the voltage peak is reached quicker with higher charge current, the topping charge will take longer.
Some chargers claim to fast-charge a lithium-ion battery in one hour or less. Such a charger eliminates stage 2 and goes directly to 'ready' once the voltage threshold is reached at the end of stage 1. The charge level at this point is about 70%. The topping charge typically takes twice as long as the initial charge.
Click to expand...
Click to collapse
source:batteryuniversity (dot) com

Charging Issues - Not charging all the way

Is anyone else having a problem with the touch pro 2 not charging fully when it is off. I have the Tilt2 and have tried many different ROMs. For whatever reason if i charge the phone while it is off, it only charges to around 96% or less. I do have the 1% battery driver installed and i can not figure out for the life of me why it will not fully charge. If i leave the phone on, it charges to 100% but at some point i get a message telling me it disconnected from the connection. Can anyone help. Thanx
Same issue :-(
me too. Same problem
There's been several threads on this. The general consensus is the battery stops charging when it reaches 100%, and then begins to discharge. I've noticed the same behavior but haven't found a fix.
Very odd
The weird thing is that I have charged my phone while it is off and one morning I wake up and turn it on and it is at 91% then the next morning it will be at 100% then the next morning itll be 86%. I usually turn it off around the same time and turn it on around the same time. I cant see it starting to discharge if there is only an hour possible time difference. REALLY annoying lol
Icon issue with charging and Battery level
I have an odd issue. I am running the stock ATT rom until I can get the stupid phone to take the HardSPL (different issue being worked on).
The icon at the top shows the battery at full capacitiy all the time. I have Phone alarm on and it has a battery indicator that shows it as low as 20% while battery icon is still 4 bars full. Also there are times when I remove it from the usb and the charging icon stays on instead of showing the battery icon. If I soft reset then it seems to go to normal and the charging icon is replaced by battery which seems to always show full.

Charging problem! slow or no charge..

ok, over the last week or so ive had this issue, gradually getting worse...
my battery will charge to around 40-45% and then charging will slow right down.
two hours later, it will be on around 50% if im lucky, and about 3 more further hours before i hit 60% (this is some of the time, other times, it just remains on its current charge%)
if i leave it overnight for about 10hours or so, highest it goes to now is about 73%, but this is rare, usually 45-50%ish.
ive tested with htc ac wall charger, htc usb, blackberry charger, car charger and a random microusb wallcharger. all have same issue.
when tested with two friends desire hd's on different days, my battery charged perfectly, and at the normal gradient speed over the % range. and my phone reads it correctly at the 100%-98% when back in my phone after change back.
i thought it was down to my phone, just dont know if its rom or hardware. shud i factory restore, or claim on insurance?
i have another issue here...http://forum.xda-developers.com/showthread.php?p=18480603&posted=1#post18480603
which also applies to the question of restore or insurance...
thanks
What Rom are you using, i am using runny 2.2 only 62% charge in 6 hours
9 hours later on battery only upto 68% i have amazing battery life now
i'm using runny 2.2.....left it on charge for 2 hours with phone on, but wifi and everything off and it had only gone up 2% ! !
Turned phone off and plugged in charger, 30 mins later, only went up 1% ! !
72% charge at this point.
So took it off charge, put it in my pocket, went upstairs to bed, turned it on to set alarm and it said 100% on battery....weird!!
matt
Lol this is an issue with calibration. The battery is charging but the software doesnt report it.
You have to charge the phone for as long as possible so you know it is on 100% whether the software says it or not, go into CWM, wipe the battery stats and then let the battery drain fully until it shuts down by itself. Then plug it in and leave it until you know for certain it is at 100%. If the green light comes on leave it for an additional half an hour. Then it will be fixed.
ive only recently got this handset, as last one was replaced on insurance a month or so ago, and its runuing on stock rom with latest updates....?

Categories

Resources