Related
Hello everyone.
I have just bought my Hermes (AT&T 8525) after one year of planing so. It came with WM5. I downloaded some of the ROMSs, radio and bootloaders commented here. I tried reading all the vast infromation in this forum and the wiki, but still having a problem.
THE PROBLEM IS AS FOLLOW:
When I start the flashing process, using HTC_TyTN_WWE_3[1].54.255.3_6275_1.48.00.10_108.exe or RUU_Hermes_CINGULAR_WWE_3.1.57.502.1_6275_1.48.00.00_108
... everything goes well, until the progress bar appears in my PC. When it appears, ActiveSync in my PC closes and my Hermes goes to stand by (the lcd goes off) so I cannot complete the installation process.
The phone works pretty well and I'm really amazed for all its capabilities. But still, I'm stucked with wm5.
Why do you think this happened?
PS: I flashed the radio (1.51.00.10) and bootloader (HARD SPL v7). My ROM version is 2.15.502.3. I use "ActiveStink" to sync my files without problems.
Any advice will be more than welcome!!
I'm no expert but that appears to be normal behaviour!
ActiveSync is only used at the start of the process. After a few files have been transfered, Activesync is closed and a different link is established. If you just leave it for a short while longer, a progress bar should appear on the Hermes too.
Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?
todd_jg said:
Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?
Click to expand...
Click to collapse
I'm having the same problem - always have. The message tells me that I'm disconnected and that I should check my USB connect etc. I left that box up there for about 15 minutes. Now I've closed the box and have waited several minutes with no activity. This is pretty aggravating. Thanks for any help.
try turning off your antivirus aplication. thats work for me flashing my tytn to wm6.
I've done everything.... I guess
Hi...
Yes, I consulted the www.mrvanx.org, excellent tutorials.
I flashed without problem the radio and bootloader. The progress bar started to "progress" and everything was fine. The only problem I have is flashing the WM6.
I don't remember where, but I readed that flashing the bootloader "Hard SLP v7" causes my HTC not to accept any Oficial WM6 ROM. The article said that I only had the chance to flash a coocked or modified ROMs. Is this true?
If not... what else can it be? I also closed all my applicacations including the antivirus, goback, disabled the internet connection, the logictec mouse center, etc. and nothing, the same as Chicoh happens to me.
"Error 260: Connection... check the USB cable bla bla bla."
Should I restart in safe mode to do the flashing?
Should I try to install a modified ROM?
Have in mind I've tried three different official ROMs: WWE, Cingular and spanish.
Thanks to all the comunity!!!
Saludos desde México!!
Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.
liquidsilver said:
Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.
Click to expand...
Click to collapse
I'm trying that as we speak. I have a good feeling about this. I'm a little concerned that I didn't think of it though. Makes perfect sense - Skip the middle man.
UPDATE: Crap. No luck. Thanks all the same though. I'm not giving up.
What OS are you using, xp or vista? My vista 'top had the same problem wouldnt flash for the longest time and i had to use my xp.
However, it does work now. Not entirely sure why.
Now I had success!!!
Hello my friends.
It seems that the article I readed days ago detailing that after flashing the Hard SPL v7, I could only install a modified ROM, not an official one from HTC or Cingular.
I downloaded Black Satin and installed it without any troubles. The entire process lasted only 3 minutes!!!
I wanted to have an official ROM, don't ask me why, and never tried the "other" ROMs that are actually excellent!!! some apps that were on WM5 are not in WM6, which is kind of sad, but if there's something that I love of WM Smartphones is that I can download and install whatever I want or develop it if it doesn't exist!!!
By the way, I use Windows XP Pro.
Thanks for all the support!!!
PS: Before flashing the Hard SPL v7, I tried installing the cingular WM6, but didn't make it. That's why I readed almost all the pages and threads here in xda-developers and found that flashing a new bootloader was a very good idea. The rest of the story is known by you.
After many flashings of roms, I finally flashed back to the official AT&T WM6 rom located at the link below:
http://forum.xda-developers.com/showthread.php?t=334771
My phone, even with my new sim card doesn't pick up any reception at all. All I get is the two arrows with the "x" and that other weird symbol with the exclamation point next to it.
I have a tilt and when I pop my sim inside, it works perfectly, no hiccups what so ever.
I live here in Hawaii and we just recently turned on the 3G network and I'm not sure if it affects my 8525.
Any ideas on what may be wrong? I had used Black Majiks WM6 on my 8525 previously but this past Monday I had issues with it so I tried flashing a bunch of times and still no fix.
I've searched through the threads for the last 2 days and everything I've tried so far hasn't work and I'm really desperate and need input from more professional users. PLEASE!!!
More information regarding phone problem.
When I try hit the green phone button, it doesn't do anything. Also going to phone settings under the settings menu, and it doesn't go there! Don't know why, I try to click it and nothing. Other icons work, not that one though.
This is getting ever more frustrating and I'm still searching through the thread for possible solutions, but nothing. Someone out there has to have some clue as to what may be wrong!
Found out another thing that might be of importance.
When I reset my device, soft or just turning it off and on, I get a "No GSM" on the AT&T screen.
Man, I've even gone as far as visiting Mr. Vanx's site to downgrade everything back to WM5. I still get the "No GSM" on my startup screen and no connection!
WTF?????????????
Well if you can get to the boot loader try flashing the official rom from HTC's Site for your phone. I'm not saying the one you DLe'd from here was bad but maybe it's just not the right one for your phone for some reason.
http://www.america.htc.com/
Well not to say the ROM you DL'ed from here was bad or anything but if you can get to the bootloader flash the officially released ROM from http://www.america.htc.com/ for your phone and see if that fixes your problem. Maybe the ROM you got from here is just not the right one for your phone or something. Worh a try anyway as you can't really use it as is.
Scrambler001 said:
Well not to say the ROM you DL'ed from here was bad or anything but if you can get to the bootloader flash the officially released ROM from http://www.america.htc.com/ for your phone and see if that fixes your problem. Maybe the ROM you got from here is just not the right one for your phone or something. Worh a try anyway as you can't really use it as is.
Click to expand...
Click to collapse
You know, the weird thing is that I tried to download stuff from the American HTC site, and I can only max out at 10.0kbps and I can NEVER get the whole file, only 15% maybe.
Talk about running into one problem after the other.
Is there a mirror out there somewhere?
Xyberz
Check your PM's
Xyberz said:
You know, the weird thing is that I tried to download stuff from the American HTC site, and I can only max out at 10.0kbps and I can NEVER get the whole file, only 15% maybe.
Talk about running into one problem after the other.
Is there a mirror out there somewhere?
Click to expand...
Click to collapse
I agree, anyone have it I can download? I keep getting lockups on my 8525 with the Schapps build and I want to try the offical build to see if it's the device or the build........but it downloads SOOOO slow......
Just finnninshed uploading RUU_Hermes_CINGULAR_WWE_3.62.502.3_6275_1.54.07.00_108_UOOS_SVN05_Ship.exe the Official ATT/HTC America file to Media Share. Here is the link for you. Hope it helps, let me know.
http://www.mediafire.com/?e0wkzvgm6ym
or
http://www.mediafire.com/?sharekey=ab1a9d4d5155409591b20cc0d07ba4d2067ccab3e6e21d05
Ok thanks for the uploads. Got the file. I just want to make sure if I should upgrade to Hard-SPL V7 before I use the update the rom?
I went all the way back to Herm SPL 1.06 and Cingular WM5. Don't want to brick the phone so wanted confirmation before I do anything else. Can't afford for things to get more messed up.
Xyberz said:
Ok thanks for the uploads. Got the file. I just want to make sure if I should upgrade to Hard-SPL V7 before I use the update the rom?
I went all the way back to Herm SPL 1.06 and Cingular WM5. Don't want to brick the phone so wanted confirmation before I do anything else. Can't afford for things to get more messed up.
Click to expand...
Click to collapse
Well I like using Hard-SPL V7 especially for the cooked roms as it gives you a bit of safety, but the rom I uploaded here is the Official HTC America / ATT Rom so you can follow their flash instructions for it. I even successfully flashed this ROM from VISTA 64 bit with no problem to my Herm 100.
As with any Flashing their is always a risk if something should go wrong that you will have a brick but your already near that point as you can't do anything with the phone at this point anyway.
GL & let us know how you make out.
So i had 6.1 but it kept freezing, so I went back to 6.0, and was going to install 6.1 again...and now the screen goes to three colors, and then the installer box says "the image file was corrupted, please check your update utility"
and i dont know what to.
any help?
please and thank you.
First of all you the Kavana's & Rickwyatt's works on T-Mobile Dash, HTC S620 & S621 and you have to make sure your phone is unlock (use SDA Application unlock) to do it.
Try to use on these Upgrades, I recommend you Kavana's 6.1 cuz is easier to install with the (.exe) file but If you want T-mobile MyFaves the Rick's version came with it, Rick is a little more complicated for a lot of files included in the installation package but If you run (install.bat) and follow the steps. And Follow the instructions.
Kavana's: http://forum.xda-developers.com/showthread.php?t=374890
Rick's: http://forum.xda-developers.com/showthread.php?t=397845
Good Luck
Adavid
By the way, if the Phone got frozen remove the battery...I got T-mobile DASH and I have install both and work's good, the problems with Rick's the open applications close automatically if you don't use it.
Good luck again
Rick's 6.1
When you unzip Rick's package you have:
USPL <folder>
Auto
EnterBootloader
rapidtool
ROMUpdateUtility
.
.
.
Just click on Auto and follow the steps.
cant install rickys kavana rom
hello-i need help pls
while trying to execute ricks rom by autobat, after a few steps an error pops in that says cant find rom update utility, make sure u typed right..etc
can someone help
thx
*staring at the stickys...looking at the n00bs guide to installing 6.1*
*pointing and laughing at all who didnt read and follow it*
*going to bed*
gixxum said:
*staring at the stickys...looking at the n00bs guide to installing 6.1*
*pointing and laughing at all who didnt read and follow it*
*going to bed*
Click to expand...
Click to collapse
Think i may have a link to it on my sig just incase they can't read threadz?
Try This it will help a lot.
well
maybe im n00b- but still, while trying to flash i get an error massage that "windows can find romupdate utility" my phone is unlocked. so, ill appriciate ur help/
Did you UNZIP the zip file prior to running the auto.bat file??
anyone have any luck getting ubuntu installed on a s620? i get a message that says "you deserve to be punched square in the mouth." i want my phone to perform as a dns server, router, network storage and cell phone. it is app unlocked.
gixxum said:
anyone have any luck getting ubuntu installed on a s620? i get a message that says "you deserve to be punched square in the mouth." i want my phone to perform as a dns server, router, network storage and cell phone. it is app unlocked.
Click to expand...
Click to collapse
The correct distro you need is dashuntu, wow and i thought you knew it all
Can't remember off the top of my head what ubuntu is translated into? Something about tree huggers, so now we can be Dash huggers
yes i have.
ive restored my xp to earlier point , now ive managed to install the rom.
for some reason i get a daily update from microsoft, seems to me they f*** my system.
the-light said:
yes i have.
ive restored my xp to earlier point , now ive managed to install the rom.
for some reason i get a daily update from microsoft, seems to me they f*** my system.
Click to expand...
Click to collapse
Glad you got it sorted.
On computer go Start\Control Panel\Automatic Updates and you can turn them off.
Turn off that Microsoft update B.S.
I have had my s620 for a while now and everything has been fine, flashed it with a rickys rom then changed my mind and went with kavanas (sp?) then something happened....
i broke the darn screen!, not a problem i replaced it. simple but... i lost all my settings, smart toolkit and the t9 programs were no longer installed?
i've been trying to flash back to kavanas or the new rose rom with no luck, whatever i do it wont run the SPL part of the auto.bat ???
i've unlocked it again, played with the usb connection settings, everything i can think of! someone please help!
i've attached a screen shot of where it hangs for you...
***EDIT*** and i have tried all the obvious things, and some of the less obvious (running the SPL file myself from the device, restarting the device, hard reset, etc)
Maybe try flashing with your official ROM first. I don't know that much but what ever is screwed up from having a broken screen might get fixed doing that. I know, annoying extra step but worth a shot...
i wish it was so simple lol!
I cant find my official rom anywhere, its a UK BT Broadband Rom ???
I've tried 3 different Roms, even tried to bypass the Auto.bat files for the roms and do the flashing manually with no luck!
Edited: (Link removed, was software update. Not the Full ROM)
There's the link to download the official BT Broadband ROM Update
The BT ROM is here http://www.mediafire.com/?mgldgtxc3gq
So did it end up working when flashing with your official rom?
well first try nope, no luck
It went through the install process and not all of the cabs installed (it copies everything to the phone and then runs individual packages) so i stopped the process in fear of bricking my phone.
Im stumped on this one, what could i of done when i replaced the screen that would stop the flashing process from working???
southect said:
well first try nope, no luck
It went through the install process and not all of the cabs installed (it copies everything to the phone and then runs individual packages) so i stopped the process in fear of bricking my phone.
Im stumped on this one, what could i of done when i replaced the screen that would stop the flashing process from working???
Click to expand...
Click to collapse
What cabs? The ROM is a .exe the first link placed on this thread is not the ROM it's the BT software update, run the BT ROM i placed link to and see if works?
Actually the first link is the newest ROM for his Phone from the BT Broadband website. I searched it quite extensively to find it. Newer then the one you posted.
Edit: http://bt.custhelp.com/cgi-bin/bt.c...at_lvl3=1978&p_cv=3.1978&p_cats=760,1851,1978
drkfngthdragnlrd said:
Actually the first link is the newest ROM for his Phone from the BT Broadband website. I searched it quite extensively to find it. Newer then the one you posted.
Edit: http://bt.custhelp.com/cgi-bin/bt.c...at_lvl3=1978&p_cv=3.1978&p_cats=760,1851,1978
Click to expand...
Click to collapse
Actually it's not it is an .msi install for the bt software update it's about 5mb in size and there is not a new bt ROM please use the link i provided....
I'm an ex BT user and i just knowz.... BT do not distribute the ROM....
Nevermind he's right, didn't read that page thoroughly...
ok thanks people, especially the person that 'searched extensively'!
I will try the link provided now and report back
Worked Perfectly
Thanks you guys, worked perfectly after i re-flashed to the original rom.
Will backup the Bt Rom for later use, just in case.
Thanks again
southect said:
Thanks you guys, worked perfectly after i re-flashed to the original rom.
Will backup the Bt Rom for later use, just in case.
Thanks again
Click to expand...
Click to collapse
Thats cool happy to help Always good to keep a copy back.
Glad to hear it, sorry for the wrong link...
Hey there,
After lots of problems with my P3300 (see this thread), I've decided to flash it to see if that helps. I'm not too bothered about getting the GSM working again as I have another phone, but I'd like to be able to run all apps again.
So... I'd like some advice please.
What would be the best ROM for me to use if I just want to use the phone as a GPS device, portable wifi web browser and notepad?
Basically something pretty stripped down with as good battery life as possible.
Is there any advantage with going for WM6 over WM5?
Bear in mind I've never done this before and am currently reading up on all of it.
From what I've read so far I'll have to do the CID unlock first (currently have WM5 in french installed and would like an english ROM)? I think it may be unlocked already but am not sure. Is there a way to check? Do I risk anything if I run USPL even though the phone is already unlocked?
Thanks in advance for any advice!
You can check if your phone is CID unlocked if the SPL number which comes up while booting during the big white HTC screen says 1.11.0000. If it says anything other than that then it's not unlocked.
Best stripped rom for me is Sheen's clean base version 3. Check it out, it's on the first page of the thread.
alternatively, if u want fast and stripped, go for yues extraclean (see my signature)
greetz
ferfecir Clean
This is the best clean rom which is a modified version of Yues clean with 30mb free ram.
http://forum.xda-developers.com/showthread.php?t=531972&highlight=ferfecir
mta33 said:
This is the best clean rom which is a modified version of Yues clean with 30mb free ram.
http://forum.xda-developers.com/showthread.php?t=531972&highlight=ferfecir
Click to expand...
Click to collapse
Pagepool 4 MB
RAM 32 MB
ROM 69 MB
Thanks for the replies. My SPL says 1.12.0000 so I guess I need to do the CID unlock.
Ferfecir Build 20931 looks like the most promising from those.
Can anyone please point me to a good tutorial for flashing the ROM via activesync? I'd rather not have to format the memory card if I can avoid it and my soft reset button is broken. (I have serached but had no luck)
Thanks!
download uspl from here http://forum.xda-developers.com/showthread.php?t=311403
and any rom you want...
unpack the uspl
plug the cable in the device and establish a usb connection
run the "start_uspl.exe" be patient...after being prompted to click some "next buttons" follow the procedure...and i mean it...follow the procedure...that with 50% battery,no programs running on the pc,no unplugging the cable and so on...
and you will have the uspl flashed
go to boot loader...The bootloader is invoked by pressing down the Power and Voicedialer buttons simultaneously, and using the stylus at the same time to press the RESET button at the left side. Continue pressing the two buttons for a few seconds after pressing and releasing the reset button until the bootloader screen appears.
if uspl says 1.11.000 then you are good to go
now you can flash any rom (cooked for artemis) and any artemis radio (i recommend you the 3.34.90.) onto your artemis
simply download,extract,run the rom update utility (RUU) ,follow the procedure and watch the show...
if you ever get an error during flash or anywhere else in the rom update utility...refer to this page and troubleshoot your troubles http://wiki.xda-developers.com/index.php?pagename=RUU_Errors
if you get an error saying invalid file size or something like that (you will get it if you try eg this rom..http://forum.xda-developers.com/showthread.php?t=465291)
go to this thread http://forum.xda-developers.com/showthread.php?t=521406 download the file and flash it if it is an ordinary rom...just run the RUU
afterwards just check it in the bootloader if it says 1.11.cmon it is ok....and you will be able to flash virtually any rom cooked for artemis onto yours
i must be damn crazy to post this thing...because it is all there in the wiki and the forum stickies,believe it or not
Thank you very much for the detailed instructions.
Just two more questions!
My reset button is broken. Can I just turn the phone off and back on to check if I have 1.11.0000 instead of using the bootloader?
And the RUU is this one? http://code.google.com/p/htc-flasher/downloads/list (only file I have for the new Ferfecir ROM is a .nbh, is that all I need?)
Thanks again.
this is a very open-ended question.
Everyone on here will have their own favourite rom....if there was 1 definate fits-all "best" rom ...everyone would be using it..but there isnt and we are all using the rom that suits us best
some people want their phone to be more like an iPod and so the multimedia aspect is a priority along with decent graphics and animated menus
some people want the PDA functionality most so they want a really stripped-down fast rom that is reliable and handles email well
everyone wants to use it their own way....thats why this site exists.
The guys who make these ROMS are the guys who say "this is good, but i want it to be more like THIS."
Follow farukb's (excellent) instructions....unlock your device properly....if you get any problems, search for the answer before asking for help....chances are hundreds of people will have had the same problem and hundreds of people will have already given the answer...and then ....just look around the site. See which roms are available that fit YOUR needs, and flash it....if you dont like it, try another.
I'm trying 6.5 roms at the moment and love it....i've flashed it probably once a week with a new ROM each time a new version is released and have seen the OS evolve....right now i'd say PDhee's Mega 6.5 M2D rom is the best of the bunch providing you're not planning on installing LOTS of exra programs.
that's the beauty of these things, if you dont like the ROM, just try another. Sometimes the ROM won't work quite right (especially if flashing ROMs between different cooks) so just try flashing it again to make sure it resets everythin correctly. If it's still not right, try a different ROM.
farukb said:
i must be damn crazy to post this thing...because it is all there in the wiki and the forum stickies,believe it or not
Click to expand...
Click to collapse
yeah, unfortunately (and it seems to have increased over the last year or so) nost people on here are noobs who can't be bothered to read through some threads or use the search and we just get the same questions asked constantly.
I dont minds helping people....providing they've looked for the answer themselves first.
every time a new rom is released there will be people asking what error 260 or 270 means?, do they need to USPL? etc etc
it's easier to ask someone else to take time out of their day to aswer your question than just type "error 260" into the search box and find out for yourself. They dont consider that people are having to answer these questions 10 times a week, in their own time, for no thanks, just to have the same question asked the next day. Purely becuase they couldn't be bothered to see if anyone else has asked that question before.
sorry...rant over....i love you all
seebasso said:
Thank you very much for the detailed instructions.
Just two more questions!
My reset button is broken. Can I just turn the phone off and back on to check if I have 1.11.0000 instead of using the bootloader?
And the RUU is this one? http://code.google.com/p/htc-flasher/downloads/list (only file I have for the new Ferfecir ROM is a .nbh, is that all I need?)
Thanks again.
Click to expand...
Click to collapse
no
you need to use the reset button (stick the stylus in the reset hole) .
Reset is like turning your computer off and on again
Power button is like turning the monitor off....it doesnt stop programs running and it doesnt properly reboot the device.
Your only alternative is taking the batter out i think (just like pulling the plug out will also reboot your computer).
If you havent already run USPL, then you probably WILL need to do it.
i dont know the specific ROM you're talking about, but just an NBH file will NOT work. You need the EXE file to run it.
Just download any suitable ROM off this site and it will have the whole package....if you're downloading from another site you'll have to ak that other site for help
my reset button doesn't work. i took the phone apart to change the touchscreen and must have misaligned something when putting it back together. sticking the stylus in the hole doesn't do anything anymore. will take the battery out instead, thanks.
regarding the rom, it is one i downloaded from here: http://forum.xda-developers.com/showthread.php?t=531972&highlight=ferfecir
the rar file downloaded from 4share (http://www.4shared.com/file/112067347/72728603/ARTEIMG-Ferfecir_-_20931_en_gncel_hali.html) only contains the nbh, no exe.
and for the record, i've spent all afternoon/evening researching this, searching this forum and the wiki etc! i appreciate it's annoying answering the same noob questions over and over again but i thought my thread was specific enough to warrant it and am grateful for all the replies.
seebasso said:
regarding the rom, it is one i downloaded from here: http://forum.xda-developers.com/showthread.php?t=531972&highlight=ferfecir
the rar file downloaded from 4share (http://www.4shared.com/file/112067347/72728603/ARTEIMG-Ferfecir_-_20931_en_gncel_hali.html) only contains the nbh, no exe.
and for the record, i've spent all afternoon/evening researching this, searching this forum .....
Click to expand...
Click to collapse
...yeah, and if you read ferfercirs description fully, you will come past "sd-card-flashing" which is the way to flash the *.nbh -part of your rom in a way without needing an activesync connecton
greetz
i did read that bit
but as mentioned a couple of times in this thread already, my reset button is not operational so i cannot use bootloader (afaik). so i assumed there was another way.
but i guess i'll find a rom that comes an an exe and save myself some trouble
no need to keep searching,
u can simple take the provided *.nbh file that came without an exe, rename it to ruu_signed.nbh, exchange the existing RUU from a complete installer-routine and off u go, provided u have used uspl first
greetz
ok thank you once again, i'll try it tonight.
one final question! do i need to have a sim card inserted while running USPL or does it not matter?
It is recommended to remove both your SIM card and your MicroSD card during any type of flashing, whether it be USPL or ROM. Even my reset button is not working anymore, my phone got dropped in water and I had to give it for repairs. After motherboard change they assembled it slightly wrong I guess, and it doesn't work. But I can still get into bootloader by just pressing the Voice record and power buttons together for 10 seconds. Try that.
Secondly, I hate to be plugging myself here, but I have just cooked a clean 6.1 ROM myself, with the latest build of 6.1 that is 21054. you might want to check that out, it comes with the full package and not just the nbh
here it is - (http://forum.xda-developers.com/showthread.php?t=551728)
Again, sorry, but Im giving you an option thats all
thormdac said:
no need to keep searching,
u can simple take the provided *.nbh file that came without an exe, rename it to ruu_signed.nbh, exchange the existing RUU from a complete installer-routine and off u go, provided u have used uspl first
greetz
Click to expand...
Click to collapse
ok i need help again sorry! i tried this but i got an error after 5% saying the .nbh was an invalid size
i used the ROMUpdateUtility.exe from Arte_WM65_23009_M2D_Mega_beta1 ROM (i removed Arte_WM65_23009_Mega_b1.nbh from the folder and replaced it with Ferfecir's .nbh which I had renamed to ruu_signed.nbh)
What did I do wrong?
I ended up flashing with Arte_WM65_23009_Mega_b1.nbh and it worked great but that ROM is too much for me and I want Ferfecir's simpler one.
Thanks
You need to flash the newer USPL which allows nbh files of a smaller size to be flashed.
thanks! it worked. everything working perfectly and my gsm works again too. woohoo.