Related
Who can share with us the knowledge, wisdom and techique of applying the screen protector correctly, evenly and eventually bubble free.
If we all admit it, we need help, or is it just me with the shaky hands and crooked eye?
Tomo said:
Who can share with us the knowledge, wisdom and techique of applying the screen protector correctly, evenly and eventually bubble free.
If we all admit it, we need help, or is it just me with the shaky hands and crooked eye?
Click to expand...
Click to collapse
I've applied a lot of screen protectors, but I'm no expert. YMMV. Even so, you want to start with a dust-free environment. Tiny specks of dust, if like me, you live out in the country, are as problematic as air bubbles, and a serious pain to remove. If you get one on a sticky surface, while you're removing it with scotch tape, you're also risking more little particles landing on it. It can be a never-ending nightmare and eventually leave the protector so marred with residue that it's no longer worth using on such a gorgeous device--so prevention is the best cure.
Step 1: Dust free room.
I recommend a bathroom for a dust-free setting. Well before taking anything inside, hit the shower on as hot as it goes and let it steam up the room, keep the door as closed as possible. Once it's off, the steam will cool and weigh down particles in the air. Once the room is no longer moist, carefully bring in your phone and protectors, maybe a credit card too without letting in too much outside air or new unweighted dust. Open and close the door slowly--quick movements will draw in lots of dusty air, but don't dilly-dally while getting inside either. It's time-consuming to set up, but worth it if you live in a dusty area.
Step 2: Orientation
Now you want to find a location on the phone that will allow you to orient placement of the protector. If the protector has a hole for the speaker, or light sensor or whatever--that's the end you want to start with because the more border you have to work with, the easier it will be to align it straight from the start. You're going to want to start on a narrow end so you are laying it down longwise as this will be easier to manage bubbles as you go mm by mm. Make sure your screen is completely clean (hopefully you haven't removed the original plastic covering until just now), and then peel off a little of the screen protectors' backing and orient it along a border of the phone. If you can get that part straight, the rest of the protector will go down straight as well.
Step 3: Slow Application
Now you're going to slowly peel back more and more of the backing as you slowly apply more and more of the protector. If you get a bubble as you go, back it up a millimeter and lay it down again more slowly. This is the time to use the credit card if you get a bubble that just keeps coming up in the same spot--don't wait until it's applied and try to push it out. That's a nightmare.
A good protector can last years if applied properly the first time and not abused. I use clairvue and they're very durable. I don't know about the included TP2 protector.
Step 4:Breathe
You weren't breathing while doing this were you? No wonder it sucks.
I alwaus use a bank Card.
being down en slowly slide the bank pass upward. This covers all the screen and leaves no bubbles. then do it a second time, mosliding the card upwards. Works for me most of the time. (at least, don't know if the screen is straight, or has a little angle in it?)
Mine went on without a problem...
first clean the screen of all gunk dust finger prints (yes we know you played befor putting on the screen protector) etc etc
Do this as said above in a dust free room or just have hoovered is normaly just as easy
peel the lower part of the protector off the plastic backing ... the backing they provide is quite stiff so you can use this to apply the protector
you only want to peel back around 1-2cm or about half an inch i chose the bit which goes over the buttons you may want to do the camera end first
I then used a glasses cloth but any decently fine weave cloth which is dust free will do and slowly very slowly stuck the protector to the screen and massaged the edge down peeling it off the backing as i went.
OPk re reading that it doesn't ake much sense but if you fold it over on itself using the backing to hold it off the screen and run the edges down you won't get air bubbles i found
Mild soapwater misted to the sticker and to the surface to be attached.
Then apply the sticker and align to the surface where to attach
Push the soapwater out from between the film and the surface.
NOTE: this is a general rule to apply stickers! I have no knowledge on phone shields.
nevermind i must have had a small bit sticking off the side the corner of mines just lifted and must have got a few small bits of dust in the gap ... i wonder if the adhesive is water soluble
Well I thought I'd screwed up my screen protector, but I salvaged it. It took about eight goes but it's on and working brilliantly.
Here are some salvaging tips:
1. When you're lifting the protector off, try and avoid bending any part too much. This is particularly relevant for the corners.
There are two ways of lifting the protector from the screen. The best is with sticky tape (Sellotape?) which can be applied near the corner and will be the easiest method. But if your stickky tape's rubbish, it might not lift the protector. In that case, you can carefully use the tip of a sharp knife to lift the very smallest amount you can. As you lift, you're looking to minimise the contact area by turning the knife sideways and definitely not allowing the knife's point or sharp edge touch the protector.
2. As it lifts, try and help the protector up by just holding the edges.
3. Take your time. The thing WILL drop back down a few times as you lose your grip, but just relax, take a deep breath and start again.
Once it's off:
1. Clean the phone screen.
2. fortunz and magius00 have given some great application tips elsewhere. Here what you're looking for is a perfectly clean screen with no dust.
Now. Before reapplying the protector:
1. Wash it with soap. I've used both shower gel and washing-up liquid. Wash both sides. Use your fingers to wash it.
2. Minimise contact with the "sticky side" once it's washed.
3. Rinse it well. Both sides. Clean water.
4. Don't bother to dry it. Definitely don't. You'll make it worse than ever. You can gently shake it to lose the largest drops. Both sides can have water droplets. Fear not.
As the protector goes on, try and minimise the contact around the edges whilst maximising pressure from the middle. Basically, the more secure the edges at this stage, the more difficult it's going to be to squeeze out any trapped air bubbles. Squeeze the bubbles from the centre outwards.
Once I'd done this about four (!) times, patiently putting the protector on and then gently easing it off again as some stray pube or grain of sand had found its way in between (how?), I eventually achieved an air-bubble, pube and sand-free application. The only trouble was the screen underneath appeared misty - but at least it was being protected; I planned on ordering a new one after the weekend. I did however notice one or two very clear patches. Now, some 48 hours after putting the protector on, the mistiness is totally gone and I have a perfectly clear, bubble-free screen protector on my lovely new toy. I don't need to order another screen protector after all.
Yayyy.
I had no problem getting mine on, but since it's been on it's already somehow managed to get scratched and it's peeling by the end call key as well.
Can't wait until there are some decent ones on the market.
Any known good makes to look out for?
dazultra2000 said:
I had no problem getting mine on, but since it's been on it's already somehow managed to get scratched and it's peeling by the end call key as well.
Can't wait until there are some decent ones on the market.
Any known good makes to look out for?
Click to expand...
Click to collapse
Brando do good ones, I have ordered mine.
Thanks to all for advice. I went with EXCIM (http://cgi.ebay.ie/ws/eBayISAPI.dll...K:MEWNX:IT&item=270398112761#ebayphotohosting )and it fitted easily and well, no bubbles or stange curly hairs. It's a bit thicker than the one that comes with the TP, but also a teenshy bit smaller which makes it a more forgiving fit on the device.
Another tip - use clear tape to lift the screen protector and / or dust from screen protector. Works like a charm!
Further to the sticky tape suggestion - 3M Scotch tape works the best for this
yippy following the in the bathroom (ensuite) method and a credit card applied my first ever blemish free screen protector (the standard one that came with unit) ...first go ....so thanks all concerned
I got a small scratch/paint chip on the black plastic near the usb port does anyone have any ideas on how I can fix this? I was thinking of using black nail polish.
Any other ideas would be appreciated.
Thanks!
Sent from my SAMSUNG-SGH-I897 using XDA App
Couple questions: is it on the rim of the charging port? I got one from removing my charge cable at an angle and it twisted and gouged the plastic on the way out, which leads me to my next question, is it deep? Like is it superficial or is it more like missing the gloss finish and possibly some plastic?
A usful product to have for glossy finishes is Displex, it works amazing on this phone. I am incredibly anal about high gloss finishes and blemishes showing up on them, even if i can only see them in direct sunlight. If you use this product with a cotton swab and gently but firmly rub in a circular pattern the scratches will go away very quickly, if you do it too much or too forcefully you may cause a bit of a clouding effect you can notice in strong light, so just do it for about 30 seconds and wipe it clean with a micro fiber cloth and do a little more, you should need a pea sided drop altogether, this will last for quite a while, just make sure you squeese the tube up and down to kind of mix it if it's been sitting a while. If the blemish is more of a gouge and not a fine scratch then this wont work as well, what it does is polishes the edges of the scratch down and fills in the bottom of the scratch with what's being polished smooth, so it works wonders for small problems, with larger issues you'll end up with a smooth ripple in the plastic as it will wear the hard edges down but obviously won't rebuild what's missing. I was reluctant to use it on my captivate cause it didn't do squat to my htc pure, but it performed remarkably on my captivate, just be methodical about how you use it and when you're done and your scratch is gone to your satisfaction be sure to put a little(and I mean little) on your micro fiber cloth or incredibly soft rag and buff over the area back and forth in one direction, for me that helped eliminate any cloudy effect and polish it back to a brand new phone shine. Just go into Google shopping and search for Displex, it's very inexpensive.
Sorry to repost so quickly but I forgot to mention about the nail polish, you can test it out but if it doesn't work I would be reluctant to use nail polish remover anywhere near the plastic on my captivate as it usually contains acetone which destroys plastic finishes usually, just put a drop on the surface of a cd, if it doesn't bother it you're probably ok, but I would still be reluctant. I'm a painter and have a lot of experience with solvents. The other possible issues with nail polish is it might not grip the phone well and depending on how thick it's applied might actually just pop off when it dries to be really hard. I tried it on my Fuze and it wouldn't cling to it at all; it also left a nasty seam and was just as bad of an eyesore as without it there, acrylic paints are easier to work with and dry very shiny but aren't always that hard, you'd need a type that mixes with a hardener as apposed to generic model paint, model paint takes considerable time to cure and wears down faster than the acrylic plastic of the phone.
Thanks for the advice my friend took a look at it and said its missing the gloss as the black finish came off and now there's a small white circle near the usb port.
I don't know how that happened as I always pocket the phone by itself and nothing else.
Sent from my SAMSUNG-SGH-I897 using XDA App
You may want to still try that polish I mentioned, sometimes with hard plastics like this the nick gives it a powdery look that looks worse than it is, if it's still relatively smooth but is an ugly blemish then it will most likely polish out to a high shine again and the white spot may go away. I don't know the process Samsung used for manufacturing but I was under the impression that they were solid colored plastic possibly with a protective coating over that, if I'm right then that white you mentioned should polish out. Best of luck whatever you decide to do.
Hello xda! This is my first post here, but I've been reading and working off of the hacking forums for a while. I own a Captivate, and I've been having some issues with my screen protector.
Every time I try to get a clean environment, I always end up with dust under my screen protector. I've read on other forums that the best method to ensure a dust-free adhesion is to do the application in a humid bathroom, and to use a drop of soapy water on the sticky side of the protector. Is the Captivate sufficiently water-resistant so that squeegeeing the water into the border of the screen wouldn't cause problems?
I wouldn't be asking if the phone had a borderless screen, but the way it's designed makes me nervous. I just want to be sure those cracks don't lead anywhere.
Thanks, I really appreciate what this forum does for Android users!
Yes. That's how most soft protectors are applied. I've applied two different kinds with a soapy water solution. Note; you only need a light mist. Some packages even come with a spray bottle just for this. I've read that liquid dish soap works best as other things like hand soap leaves residue (hand moisturizers and such).
However, another method I like to use is to simply install the screen protector outdoors (obviously away from heavily pollenated areas). You'd be surprised at how much less dust there is in that big scary place with the blue ceiling.
Humid bathroom means you're running a warm shower. If the mirrors and the screen protector are fogging up it's too humid.
I take a bowl and put 2 squeezes of soap into it and then stir it with my finger. Then I dip the screen protector into the bowl (don't forget which side is the sticky one), making sure its thoroughly covered as well as my fingers.
Shake off as much of the soapy water as possible then quickly stick the screen protector on and use your thumbs to slide it in the correct position. Squeege as much water out as possible but otherwise give it a full day or two to dry.
Oh, and take the battery/SIM out of course
Your phone will be fine. Like JPS81 said, use liquid dish soap and just a little bit. Also, when you do the mix, let it sit for 10-15 minutes or until the bubles go away, it will be a whole lot easier when applying the protector. If you are still scare, when you are using the squeege or credit card to take the water out, use a cotton cloth so it can absorb the excess water.
I installed a Bodyguardz screen and full body protector on my Captivate. That requires wetting the protectors and it worked out just fine. I've also done it with Blackberries which have much more spaces liquid can get into and had no problems.
As long as you dry up the drops that squeeze out of the sides, the phone will not really get wet inside. Makes sense to allow it to dry out a bit before putting the battery back in just in case.
I accidentally dropped my Captivate in a bowl of water and it was completely submerged for a few seconds. I took it out, and after wiping it dry it was as good as new.
Applied using this method for the first time with two Captivates - it works great, and even if a little water enters the speaker or the sides, it doesn't hurt it. Anything less than submerging the protectors in water yields really ugly results.
So, screen sizes getting bigger seems to be making it more and more difficult to apply a screen protector without getting any stray cat hairs or dust in between it and the screen. How do you guys do it, or do you just put up with a bit of dust?
I just got a wet application screen protector today since that was the last kind of protector I successfully applied to a phone (long ago), but that was a no go. It seemed fine until I was done and realized that somehow, from some where, a bunch of hairs got under the protector. I tried to use some tape to get them off but it didn't work, and then I dropped the protector and things just got worse from there.
This was in the bathroom after taking a steamy shower as I have read over and over that it's supposed to get most of the crap out of the air.
How do you guys do it? I have looked it up several times, but I just don't get how these people have such an easy time of it.
I use painters tape after I clean the screen (before applying of course) to make sure no other dust or hairs are on the screen. Use a can of air to blow away crap in your work area also.
Sent from my Galaxy Nexus using xda premium
I'm really really good at applying screen protectors (wet application) because I started using Invisible Shield when they first came out about 10 years ago.
The trick is to not use their solution, as they only give you like a tiny vial of solution.
1. Get a plastic cup (I use one of those red beer-pong cups), fill it with warm water to the top, put 2 drops of dish detergent in, swirl your finger in it. That is your solution.
2. Remove the protector from the backing, dip the entire thing into the cup, place it on your screen. You should be able to easily move the protector around the screen to adjust positioning. If you cant, take it off, dip the whole thing in the solution again, and put it on the screen again. Yes, your device will get very wet, but do not worry... it's not a problem at all (I've done this to tons, and I mean tons, of phones/cameras/gps, etc...) Don't worry.
3. Once you're happy with the positioning, use a credit card to squeegee out the water in between. Adjust positioning again to make sure it's perfect, squeegee again. Squeegee a few more times, make sure you've gotten as much water out as possible. If your device has rounded corners (such as the back of the note 2 cover), after you squeegee out all the water the corner will still stick up. Put your finger on each corner for a few seconds, maybe 20-30 seconds if necessary. It will stick.
4. Done. It will be invisible, you will not notice a thing on your phone.
Kobe_No_Means_No said:
I'm really really good at applying screen protectors (wet application) because I started using Invisible Shield when they first came out about 10 years ago.
The trick is to not use their solution, as they only give you like a tiny vial of solution.
1. Get a plastic cup (I use one of those red beer-pong cups), fill it with warm water to the top, put 2 drops of dish detergent in, swirl your finger in it. That is your solution.
2. Remove the protector from the backing, dip the entire thing into the cup, place it on your screen. You should be able to easily move the protector around the screen to adjust positioning. If you cant, take it off, dip the whole thing in the solution again, and put it on the screen again. Yes, your device will get very wet, but do not worry... it's not a problem at all (I've done this to tons, and I mean tons, of phones/cameras/gps, etc...) Don't worry.
3. Once you're happy with the positioning, use a credit card to squeegee out the water in between. Adjust positioning again to make sure it's perfect, squeegee again. Squeegee a few more times, make sure you've gotten as much water out as possible. If your device has rounded corners (such as the back of the note 2 cover), after you squeegee out all the water the corner will still stick up. Put your finger on each corner for a few seconds, maybe 20-30 seconds if necessary. It will stick.
4. Done. It will be invisible, you will not notice a thing on your phone.
Click to expand...
Click to collapse
Will this work with SGP Ultra Crystal screen protector? or are they only the non-water applyable?
Can't speak specifically for the sgp but I've been using the wet application method on all my dry application protectors for some time across at least 5 different phone models with no issues. Much easier to apply accurately than dry
Sent from my SGH-T889 using Tapatalk 2
degeneration said:
So, screen sizes getting bigger seems to be making it more and more difficult to apply a screen protector without getting any stray cat hairs or dust in between it and the screen. How do you guys do it, or do you just put up with a bit of dust?
I just got a wet application screen protector today since that was the last kind of protector I successfully applied to a phone (long ago), but that was a no go. It seemed fine until I was done and realized that somehow, from some where, a bunch of hairs got under the protector. I tried to use some tape to get them off but it didn't work, and then I dropped the protector and things just got worse from there.
This was in the bathroom after taking a steamy shower as I have read over and over that it's supposed to get most of the crap out of the air.
How do you guys do it? I have looked it up several times, but I just don't get how these people have such an easy time of it.
Click to expand...
Click to collapse
I read some where that you should apply it in a bathroom and before you start get a spray bottle and put water in it. A couple sprays in the air before... No dust works for me
Sent from my SGH-T889 using XDA Premium
Well I just got 2 more cheap protectors in the mail, the first one I tried to get perfect, and each time I tried to get rid of a piece of dust it would get worse. The second one I have one bubble and I gave up. Fine. I have a bubble... oh, and they are cheapo reflectors, and supposed to be matte... so now my screen looks pretty horrible. Sigh. Whatever, my screen is protected. I will get an SGP later and figure something out in the mean time... maybe take them to a tmo store since they did it for me last time and it came out perfect somehow. I think my house is just too dusty, and there's no way to change that. I live in the desert, I have cats, the place is old. Sigh.
omg just did both of the note 2's and it took about 30-40 minutes, ridiculous, but afterwards looks nice till today i had the damn T-Mobile protector on it lol i got tired of seeing T-Mobile =P
Here's the trick for me. I got in the bathroom turn on the shower for a good few minutes. (Hot water) because the humidity in the air will get rid of most of the dust. Then you apply your screen protector by 1st.
Positioning it first without taking off the adhesive side (to know where the edges should be)
2nd.
You must not use a credit card to squegee out bubbles that'll scratch the screen, if you are put a microfiber cloth over the credit card so you'll be pushing down with the cloth not the card
Sent From the Van Down by the River
phreshjoker said:
Here's the trick for me. I got in the bathroom turn on the shower for a good few minutes. (Hot water) because the humidity in the air will get rid of most of the dust. Then you apply your screen protector by 1st.
Positioning it first without taking off the adhesive side (to know where the edges should be)
2nd.
You must not use a credit card to squegee out bubbles that'll scratch the screen, if you are put a microfiber cloth over the credit card so you'll be pushing down with the cloth not the card
Sent From the Van Down by the River
Click to expand...
Click to collapse
Well i did it at my dining table and i regretted doing so because I ended up getting a few particles underneath, but all you need to do at that point is take any type of sticker (mine came with 2 stickers which were called Dust Removal stickers, but its truly a regular sticker lol) so I had to use that several times, but the final result is great
I ended up ordering the SGP Ultra Crystal and also ordered MobC from amazon (http://www.amazon.com/gp/product/B009M7TZYO/ref=oh_details_o00_s00_i00) which ended up coming in first, so I am still waiting for the SGP but honestly i do regret ordering them because the MobC are freakin great, crystal clear, and i have no regrets of putting it on!
Kobe_No_Means_No said:
I'm really really good at applying screen protectors (wet application) because I started using Invisible Shield when they first came out about 10 years ago.
The trick is to not use their solution, as they only give you like a tiny vial of solution.
1. Get a plastic cup (I use one of those red beer-pong cups), fill it with warm water to the top, put 2 drops of dish detergent in, swirl your finger in it. That is your solution.
2. Remove the protector from the backing, dip the entire thing into the cup, place it on your screen. You should be able to easily move the protector around the screen to adjust positioning. If you cant, take it off, dip the whole thing in the solution again, and put it on the screen again. Yes, your device will get very wet, but do not worry... it's not a problem at all (I've done this to tons, and I mean tons, of phones/cameras/gps, etc...) Don't worry.
3. Once you're happy with the positioning, use a credit card to squeegee out the water in between. Adjust positioning again to make sure it's perfect, squeegee again. Squeegee a few more times, make sure you've gotten as much water out as possible. If your device has rounded corners (such as the back of the note 2 cover), after you squeegee out all the water the corner will still stick up. Put your finger on each corner for a few seconds, maybe 20-30 seconds if necessary. It will stick.
4. Done. It will be invisible, you will not notice a thing on your phone.
Click to expand...
Click to collapse
degeneration said:
So, screen sizes getting bigger seems to be making it more and more difficult to apply a screen protector without getting any stray cat hairs or dust in between it and the screen. How do you guys do it, or do you just put up with a bit of dust?
I just got a wet application screen protector today since that was the last kind of protector I successfully applied to a phone (long ago), but that was a no go. It seemed fine until I was done and realized that somehow, from some where, a bunch of hairs got under the protector. I tried to use some tape to get them off but it didn't work, and then I dropped the protector and things just got worse from there.
This was in the bathroom after taking a steamy shower as I have read over and over that it's supposed to get most of the crap out of the air.
How do you guys do it? I have looked it up several times, but I just don't get how these people have such an easy time of it.
Click to expand...
Click to collapse
For with app screen protectors...exactly as Kobe mentioned. Couple of drops / 1 part dish washing liquid to 5 parts water (distilled water if your tap water has too much minerals)...just so the solution is slippery enough for the application process. Run your finger nail down the edge of the credit card / tool your going to use to ensure there are no nicks / sharp edges that will damage / crease your wet app screen protector.
Steamed bathroom also helps.
I recommend dry applications for flat surface...wet applications for curved surfaces.
With dry app screen protectors, those clear / ultra clear packs off of eBay usually work well. The only issues I have seen is that the adhesive may get weak over time (if you need to lift protector to remove dust then press down again) and initial cutouts maybe hard to see from pics. Eventually these dry app screen protectors fall to 3/5/? packs per <$1 ???
Position the dry app screen protector then apply / remove film. There will probably be dust, pet hair, etc. Lift up one corner / side / section at a time and slide the shipping tape between the screen protector and screen (sticky side of shipping tape against sticky side of screen protector)...then press dry screen protector down on the shipping tape which will also press against the screen. Carefully lift the corner / section of the screen protector...then flip the shipping tape over and slide back under between the screen protector and screen (sticky side of shipping tape now facing screen) if needed. Usually the particle is on the sticky screen protector side, but sometimes it maybe stuck to the screen side. The idea is to use a shipping tape with strong enough adhesive to remove the particle without ripping off / damaging the screen protector adhesive. Painting tape adhesive maybe too weak in removing any dust / pet hairs...UPS grade shipping tape maybe too strong...I like Staples equivalent shipping / packing tape...it has just enough adhesive strength to remove any dust / pet hairs.
Hope some of this helps.
What works for me:
http://forum.xda-developers.com/showthread.php?t=1988725
Got my spigen... I am probably never buying from anyone else. Well, I dunno, but from the packaging to the application I felt like I was using quality. I thought I had ordered the ultra crystal but I actually went for ultra oleophobic for some reason... and I am crossing my fingers that the surface tension changes after some use (doubt it) but it does do what it says, finger prints do not stick. However the down side is the s pen doesn't feel nice against it (it did feel really nice against the crappy matte protector, felt like a pencil on paper, but I couldn't stand the rainbow effect, maybe I will try a spigen matte in the future). Any way, I used the "hinge" technique I saw somewhere online and it worked pretty well. Got 3 pieces of dust under the screen (1 on the screen, 2 on the bezel) and I used some scotch tape to life the protector and one of the included dust removal stickers to quickly take care of the problems.
the protector is FREAKING INVISIBLE! right now the screen is off and I can see reflections, and I can barely make out where the protector ends.
Thanks for everyone who gave me their tips and tricks, I finally have a screen protector on my note that I am happy with.
Also, for those people going naked, it doesn't affect my screen but I saw I already have 2 minute scratches on my screen. I keep my phone in my pocket on its own, and somehow I managed to scratch the screen already (got on release day). I have wasted a bunch of cash getting a screen protector on that I was happy with, and I might spend more in the future, but at least I know that if anything terrible happens I can replace the little piece of plastic instead of forever having to deal with a scratch.
EDIT: playing around with it some and then wiping it off, I already am fine with how the S pen feels. I think it was actually sticking to whatever they used to apply the outer layer of protection that you remove after applying the protector. A little bit more drag then on the naked glass, but I like that I can now get more of a tactile response of my writing. I am hooked on Spigen.
I do all my screen protectors at the dinning room table in about 2 mins with perfect results every time. I attached a few screenies but they really don't do it justice. It is insanely hard to get a good picture of something clear when using a flash. the specks of dust that are noticable are on top of the protector not underneath. I'm using the spigen oleophobic and love them.
I have to have it perfect, but i always end up with dust/dirt bubbles, or it`s not aligned correctly.
I would pay to mine fitted perfect, why does somebody not set up a business fitting them.
Phone shop`s should offer the service for a small fee.
I usually buy a cheap pack or 6-10 as i throw a lot away, or still end up not having one fitted.
John.
Tinderbox (UK) said:
I have to have it perfect, but i always end up with dust/dirt bubbles, or it`s not aligned correctly.
I would pay to mine fitted perfect, why does somebody not set up a business fitting them.
Phone shop`s should offer the service for a small fee.
I usually buy a cheap pack or 6-10 as i throw a lot away, or still end up not having one fitted.
John.
Click to expand...
Click to collapse
For dry applies, look up the hinge method on Youtube, it makes applying screen protectors a breeze, and gets things perfect every time the first time. As far as dust goes, I recommend shining a LED flashlight around the screen, and using a piece of tape to spot remove every last bit of dust just prior to peeling the screen protector's 1st side up.
For wet applies, I find that I get better results by not using any soap, and just using water by itself. Less chance of it appearing cloudy or hazy after it dries. The key is to use liberal amounts of water to keep the protector sliding.
Every time I install one I screw it up so I finally gave up and just started picking them up at the AT&T store and let them do it. Ordered a mime ghost glass a while back and was heading down to the AT&T store to see if they would install it, but stopped at Radio Shack on the way there and those guys were more than willing to install it for me also. The guy said the mime is much easier to install because its more solid and not like those flimsy cheap ones you buy elsewhere. Seems most places that sell them aint got no problem installing them if they aint all tied up with other stuff.
Thats the problem. the cheap ones do not stick as well as the ones from good companies such as Spigen, MediaDevil, martin fields
glass protectors are the thing now, MIME feather glass from the USA is the best
Tinderbox (UK) said:
I have to have it perfect, but i always end up with dust/dirt bubbles, or it`s not aligned correctly.
I would pay to mine fitted perfect, why does somebody not set up a business fitting them.
Phone shop`s should offer the service for a small fee.
I usually buy a cheap pack or 6-10 as i throw a lot away, or still end up not having one fitted.
John.
Click to expand...
Click to collapse
I would use the hinge method for placement, as far as the dust/dirt try the shower method. Run the shower for five minutes with the door closed on hot (allows steam to form). Turn off shower and allow the steam to settle (2-3) minutes, this pulls the dust and dander out of the air. Then apply the screen protector to the handset.DO NOT leave the handset in the bathroom while the rooms fills with steam or when it is settling. I did not believe this method would work but I have used it on my Rezound, Droid X, Nexus 7 tablet and my HTC One with dust/hair free installs.
I used to be clumsy at it, but now I fit mine flawlessly. I have done it with 3 phones and 2 tablets and all of them were bubble free. My rule, keep the device under a light so you can see the dust particles or anything else clearly. Wipe it with micro fiber (or use alcohol wipes if the surface is smudgy). Use a scotch tape to remove the dust particles, small strokes, even in the areas which look clean. It takes 2 minutes to cover the whole device. Align the screen protector across the edges and work your way down, making sure the sides align and are in straight line. You will get bubbles which you can then remove using a credit card by wiping them towards the edges. Works for me everytime.
I work at a cellphone store and whenever someone buys a screen protector we install them for free glass or plastic:laugh:
what I find is the easiest method of applying a film screen protector and worked for me for 2 years whilst working in a vodafone store is the following:
1) ensure the screen is clean of dust, a good cloth in a relatively clean environment does the job, if not do it near a boiling kettle.
2) before peeling off the first layer line the screen protector up along the top of the handset, where you would like it begin. (for the htc one, it would be just below the top speaker grill),
3) peel back the first layer only slightly, line and up press down adhesive side with the top of the handset, easiest done with the top of the handset facing away from you. (benefit of this is, you've pulled the whole thing off and it's less likely to catch dust if only a small part of the protector is visible to wilderness.
4) with the top of the protector adhered to your screen, swivel the phone around so the top is closest to you without letting the protector move from it's position,
5) from here, it is a simple task of taking a piece of cardboard or hard paper and gently push forward from the top, whilst slowing peeling back the bottom plastic until you're at the bottom.
6) you may have some small bubbles right on the bottom edge of your protector, just use your thumb or the paper to gently squeeze them out.
Works for me 90% of the time. Also depends somewhat on the quality of the protector. But I would recommend a Glas.Tr or MIME type protector.
I love that dust remover that came with the mime. I covered the whole screen, ripped it off and put the glass one on in less than a second.
I bought mine from mobilefun.com. Don't remember exactly which, but it was one of the "premium" ones (not cheapest). From a 5-pack I got it perfect on the 4th try! Be patient and read the insructions carefully (which I didn't before the 3rd try) hehe ...
OK, i read no instructions apart from which tab to pull of first on the protector, i cleaned the screen with the included cloth, no steamy room or anything, it took me five attempt's to get the protector in the right place and there were bubbles galore, but i managed to get them all out, no dust underneath that i can see so i wasted no screen protectors i still have two left.
John.
Three things are recommended, dust removing sticker, microfiber cloth and a room with heated vapor such as a bathroom, after you have showered(dont take device in during shower).
I got some cheap matte ones from eBay... They are truly awsome and fit the whole screen(you must be pro master on fittin screen protectors)
http://www.ebay.com/itm/35084675949...eName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
My secret for fitting perfectly is to hold your screen down after wipin all the dust while getting the protector ready itself... Once I put it on without any dust under ir, I press it very hard and move it in direction where I need if not correctly positioned... When its just sticked on, you can still move it slighty - thats all it takes to get those 0,1mm right