Develop Bugs

URGENT help on Hard SPL screen

Hello,
I executed the Hard SPL cab and went into bootloader or some sort of a multi colored screen which says IPL - 0.50 Trin100 and underneath it says SPL 3.03.0000. It connects to my computer and says USB but when I attempt to flash the new WM6 rom which I just downloaded from the rapidshare it resets the machine and continues to remain on this screen of multi colored stuff. I cannot seem to get out of it no matter what I do. What do i need to do to abort the multi colored screen or allow it to flash my HTC trinity with the Dopod WM6 rom?
Thanks,
Gilbert
PS: please don't shoot me if this was discussed elsewhere. i searched and could not fine anyting

happened to me yesterday.
with this screen install AGAIN the hard....
see
http://forum.xda-developers.com/showthread.php?t=316113
and
http://forum.xda-developers.com/showthread.php?t=312499 -page 45

How? I try to execute again the Hard SPL file and it gives me an error and says close window on PC.
Thanks,
Gilbert

it keeps giving me error in connection and i think i bricked my phone i tried to reinstall several times and i get the same results. Poor me.

Same hapen to me, then ive tried to instal over it a another rom and it came to life.

if you're in the bootloader already, try and run the RUU (update program) again on your pc after reconnecting your device.. if that doesn't work, please give details of the error. I don't think you're bricked yet

racerx_ said:
if you're in the bootloader already, try and run the RUU (update program) again on your pc after reconnecting your device.. if that doesn't work, please give details of the error. I don't think you're bricked yet
Click to expand...
Click to collapse
Thanks for your help. I get Error 260:
The update utility cannot connect to your pda. please check usb is connected. click exit to quit.
When I try to run the upgrade alone in XP it starts at 1% then resets the bootloader.
Thanks,
Gilbert

k which upgrade are you running? still trying to get hard spl working, or running the Dopod WM6 upgrade?
*i've been having some troubles upgrading today too, with the WM6.. scary times ha*

racerx_ said:
k which upgrade are you running? still trying to get hard spl working, or running the Dopod WM6 upgrade?
*i've been having some troubles upgrading today too, with the WM6.. scary times ha*
Click to expand...
Click to collapse
I am trying to upgrade the
RUU_Trinity_DOPODASIA_WWE_3.00.707.17_6275_1.46.00.11_108_Ship but i also tried to reflash the 1.23 HTC rom with GPS to see if it would flash since my device is an HTC trinity and not dopod but the same thing keeps happening.

Try to flash PDAVIET version, my came to life doing this

have you tried to flash any other ROM? I was stuck with the same thing, but managed to flash a cooked ROM..
what's your bootloader showing?
if you fail to flash any other ROM, i think you need to try the stack overfow exploit posted here.. http://forum.xda-developers.com/showthread.php?t=308691&highlight=error+206
it's a bit technical, but i think it's your best bet if all else fails.. Pof might be able to help you over there

No matter what i do, what rom i try to flash i get the same damn error message: Error 260 - Connection!!! I am connected so I don't what is wrong with it. I will try some more then decide to take a hammer and break it into 1000 peices.
Thanks.

racerx_ said:
have you tried to flash any other ROM? I was stuck with the same thing, but managed to flash a cooked ROM..
what's your bootloader showing?
if you fail to flash any other ROM, i think you need to try the stack overfow exploit posted here.. http://forum.xda-developers.com/showthread.php?t=308691&highlight=error+206
it's a bit technical, but i think it's your best bet if all else fails.. Pof might be able to help you over there
Click to expand...
Click to collapse
My bootloader is showing the following:
Trin100
IPL-0.50
Trin100
SPL-3.03.0000
Thanks for all your help.

hmmm... i'm not familiar with that SPL number... unless somehow that got halfway updated with the WM6 update.
I think you better head to that thread and try the stack exploit. Did you try loading a cooked ROM to see what happens?

that is it. i give up. i am not experienced in messing with codes. i am going to retire the device for good and use a regular phone. this is crap. thanks for ur help.

oh, that is the SPL version of the new ROM... i guess you weren't using hard spl when you tried to flash it?
ha, well don't give up too quick.. that's one expensive retired device you've got there.

Just keep cool and you should try to install an official Rom to downgrade this SPL !!
Gilbert said:
I will try some more then decide to take a hammer and break it into 1000 peices.
Thanks.
Click to expand...
Click to collapse

Help!
My bootloader is showing the following:
Trin100
IPL-1.00
Trin100
SPL-9.99.CP
When upgrading with the new released WM6 ROM, it keeps failing at 28%
Please help!

best bet for you, is load a different ROM now. Either cooked or official. That will get your device out of crash-proof spl bootloader.
Once the ROM is loaded, if you want to try the official wm6 again, run SSPL first and see if it'll work for you
p.s. i pm'd you my handphone number in case you've got trouble still..

Gilbert said:
My bootloader is showing the following:
Trin100
IPL-0.50
Trin100
SPL-3.03.0000
Thanks for all your help.
Click to expand...
Click to collapse
Hi Gilbert,
Im having exactly the same problem as you. Right now im in the middle of flashing it back down to WM5 (its working at the moment at 17%).
Hopefully after this i will be able to flash back to WM6 (Most probably will go back to AX3L for now).
Hope this helps you out (im quite stressed about it too!)
Edit: I have just finished flashing to Official WM5, now flashing back to AX3L WM6. It works!

Urgent! My diamond has hardware problem and need to fallback to stock ROM and SPL.

Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810

Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help

Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.

If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included

Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.

You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU

I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!

Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.

band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?

Here you go....I did a search

Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!

Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4

band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...

kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.

f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that

f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.

Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??

R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?

f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...

f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??

Can't get rid of 1.40 OliNex HSPL, need help

Hi all,
I have 1.40 Olinex HSPL (Official ROM & Radio), this version prevents me from upgrading to the newest Official ROM. It reaches 100% and then shows 270 error and stuck on bootloader no matter what i do, to bring it back again i need to reflash with the old ROM.
I tried to flash the Original SPL (all versions), didn't work (the flash goes well, but the SPL stays 1.40 Olinex), I tried to flash it to a different HSPL (all versions too), still no go...
What should i do ?
Thanks

liamR said:
Hi all,
I have 1.40 Olinex HSPL (Official ROM & Radio), this version prevents me from upgrading to the newest Official ROM. It reaches 100% and then shows 270 error and stuck on bootloader no matter what i do, to bring it back again i need to reflash with the old ROM.
I tried to flash the Original SPL (all versions), didn't work (the flash goes well, but the SPL stays 1.40 Olinex), I tried to flash it to a different HSPL (all versions too), still no go...
What should i do ?
Thanks
Click to expand...
Click to collapse
1.40 Hard spl can not be overwritten as it's protected. You need to search for an app called Jump SPL. This utility will allow you to switch Hard SPL's.

liamR said:
Hi all,
I have 1.40 Olinex HSPL (Official ROM & Radio), this version prevents me from upgrading to the newest Official ROM. It reaches 100% and then shows 270 error and stuck on bootloader no matter what i do, to bring it back again i need to reflash with the old ROM.
I tried to flash the Original SPL (all versions), didn't work (the flash goes well, but the SPL stays 1.40 Olinex), I tried to flash it to a different HSPL (all versions too), still no go...
What should i do ?
Thanks
Click to expand...
Click to collapse
Unpack the attached archive. Connect your device to activesync and run the batch file (diamond-sspl.bat), press enter twice to copy the needed files to your diamond, press enter again and the file jumpspl will start on your device. Press the button on your device, which appears. Now your screen will turn black. Last step is to run your desired SPL. Done

Thanks it worked!

liamR said:
Thanks it worked!
Click to expand...
Click to collapse
You're welcome.

If 1.40 olinex is protected how to back to shippedSPL?

please refer to http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39

liamR said:
Hi all,
I have 1.40 Olinex HSPL (Official ROM & Radio), this version prevents me from upgrading to the newest Official ROM. It reaches 100% and then shows 270 error and stuck on bootloader no matter what i do, to bring it back again i need to reflash with the old ROM.
I tried to flash the Original SPL (all versions), didn't work (the flash goes well, but the SPL stays 1.40 Olinex), I tried to flash it to a different HSPL (all versions too), still no go...
What should i do ?
Thanks
Click to expand...
Click to collapse
i have the same as you and i don't have that problem .

I changed 1.40 olinex hardspl to 1.93 without any problem.

Thanks Man

arte200 not restoring

i am new to this forum. my arte200 only shows bootloader. on bootloader it shows;
IPL: 1.25.0001
SPL: 1.25.0000
i searched in this forum and downloaded many roms but all not helping. some stop at 1%, 3% and 6%. i downloaded the uspl but it doesnt help since phone can only be in bootloader.
can someone recommend me a rom to unbrick this phone?

You must use a S-SPL (Software-SPL) or H-SPL or (Hardware-SPL)
Go to upgrade section for Artemis to find uSPL

i have already downloaded the uspl but it seems it cannot be used with phone in bootloader. but my phone can only enter bootloader. any other idea?

Download the Original rom

bbk said:
Download the Original rom
Click to expand...
Click to collapse
please can u recommend the particular rom for me to use. and also place of download.

I'm sorry but i don't know your Rom.

I need!!! Oficial Vodafone SPAIN ROM

Hi!
I need the oficial VODAFONE spanish ROM with CID: VODAP30
I bricked my phone!!!! and i can't put HARDSPL to reflash
NEED!! help!!
Sorry for my english!
Thanks!!!!!

Hi jsaltiveri
Welcome to XDA
the best i can do is tell you where to look, as i am english, i am unable to find a rom for your phone, however, i dbout you bricked it.
first go to HTC and download a diamond ROM
plug your diamond into your PC
plug your diamond into your PC
hold the Vol- and reset
continue to do so until something appears on the screen
run the EXE you downloaded from HTC, follow on screen instructions
any Probs, feel free to PM Me

VODAP30
Badwolve1 said:
Hi jsaltiveri
Welcome to XDA
the best i can do is tell you where to look, as i am english, i am unable to find a rom for your phone, however, i dbout you bricked it.
first go to HTC and download a diamond ROM
plug your diamond into your PC
plug your diamond into your PC
hold the Vol- and reset
continue to do so until something appears on the screen
run the EXE you downloaded from HTC, follow on screen instructions
any Probs, feel free to PM Me
Click to expand...
Click to collapse
Thanks! for your answer Badwolve1
I tried to update with oficial vodafone UK ROM and showed me that invalid vendor ID
I tested with emergency vodafone ROM from spanish group that has the universal CID 111111 but obviously don't pass from 0%, I think that first checks the correct CID, and it stop if is not correct
And the all HARDSPL is the same error! not pass from 0%
Thanks!!!

Try this
Oficial Vodafone Rom 1.93 ESN
Extracted from:
http://www.htcmania.com/showthread.php?t=29059
good luck

carlis87 said:
Try this
Oficial Vodafone Rom 1.93 ESN
Extracted from:
http://www.htcmania.com/showthread.php?t=29059
good luck
Click to expand...
Click to collapse
Thanks! But this ROM is just with CID 111111 , and when I try to flash it not pass from 0%

try to load new hardspl
you can try to reload hardspl..
Update stops at 0%
Short answer: You're running the normal HardSPL and you're trying to flash an unsigned (not signed by olinex) ROM. You need the developer version which fixes the 0% issue. Link is at the bottom of this post. Read on to understand the difference between Standard/Developer Edition!
Long answer: First you need to understand that there are two definitions of "signed". HTC and the mobile operators sign ROMs so that the RUU flash utility allows them to be flashed. Usually this is what the word "signed" in the filename means.
Then there is another definition of signed: The developers of HardSPL introduced their own signing process. They want to ensure that people flashing cooked ROMs can rely on a certain quality standard. The normal version of HardSPL will only allow ROMs signed by OliNex to be flashed. If the ROM you are about to flash is signed, it will say so in the thread you got it from. If it isn't signed, you will need the developer version of HardSPL. That one will allow any ROM to be flashed. Get it at the bottom of this posting.
A note on this: The signing process by olinex makes sure that the ROM you're about to flash won't brick your device. It doesn't mean all other ROMs are necessarily evil.
Click to expand...
Click to collapse

ERROR 262
the-funky said:
you can try to reload hardspl..
Click to expand...
Click to collapse
I try with signed HARD-spl, but the same error 0% error 262
Nobody? have the solution??
Thanks!
Jordi