Hello everybody.
I am trying to update my phone, with WM6.0, however I am getting a country id error. The version I got for testing reasons is WWE. My IMEI is 35703600732450***
Could anyone help me, how am I suppose to achieve that?
there are flashtools with noID.exe in the end which dont
fail on country id errors
try looking for your device at buzzdev.net
Thanx Rudegar
However, I have an unlocked device. I unlocked it throud imei-chek.co.uk paid service. Will this help, or I still have to use a noID.exe?
If you have your device unlocked than that error shouldnt occur. However if you still get it then its inevitable i'd say to use the noID RUU.
my himalaya was never sim locked
but if i try to flash it using HimaUpgradeUt.exe i get
that error
when i flash it using HimaUpgradeUt_noID.exe
i dont
the noID at least in my case have to do with operator settings
not simlocks and the likes
if the rom dont know the operator code it will give that error
Ok, thanx. I got the files from here http://forum.xda-developers.com/showthread.php?p=1361468#post1361468 and everything worked fine (except that Thai keyboard...)
Related
hi i have xda1 with t-mobile
it only shows t-mobile and hangs there
it shows
t-mobile
4.01.19
which rom should i use and what is the method to write that rom
Thanx in advance
Normally you should see ROM Version (in you case 4.01.19) and also 2 other Version. But I´m sure, you do not see this numbers....
I think you have flashed the wrong radiostack to your device and now you have GSM Error when you enter the bootloader....
Try this instructions:
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_GSMError
Stefan
any thing else
i ve downloaded the same rom version on my phone but still it hangs at the startup with showing
3.17.03
with no radio versions and etc.
The phone was fell down from me and it started the problem from same time.
plz give me solution it is very urgent
You may have damaged some internal component when you dropped the phone. Are you pushing resetting the phone after flashing, by pushing once in the hole under the headset socket then wait one minute and push once more.
You are saying that you have ROM version 4.01.19
If I remember correctly that ROM version can only be unlocked using the SD card method. Is it possible that somebody tried to unlock it and screwed it up?
Either way it sounds like you need a new main board for it.
my phone is finally ok with some problems
i ve successfully made my mobile in working condition by some technical methods but i still have some problems with its software. from where i can get the exact radio stack for being used here in Pakistan. is it wants auto configuration but my operator and country is not listed in that menu.
3.17.03 ENG
6.24.00
324e4
which radio stack i must install and from where i can get it?
Thanks in advance to all members
hi
if someone want to know how i successfuly repaired it u can ask me
RE: my phone is finally ok with some problems
I just shipped an SX56 to a customer in Karachi, Pakistan and he is apparently happy with it.
It was upgraded with this file: sx56_WM2003_update.exe
G1.3.3
RA.33.02
A.30.09
RE: my phone is finally ok with some problems
Forgot to mention it, that file also upgrade the radio stack.
What abt my regional settings
Thanx but cud u plz tell me how can i get logon with my sim card coz my phone is not giving signals ? it wants some kind of customization process but my country's network is not listed in it
Thankx
After trying to upgrade radio stack to version 4.24.20
i just tried to upgrade my radio stack to above mentioned version. Now i m gettin an error message that says "cant upgrade rsu prss ok to restart" it comes again and again. rsu upgrading was done first time with no errors but soon after it,it start giving me that message and in the startup screen it shows the previous version of radio stack which was 6.24.00. Plz tell me what is wrong that i did and how to resolve that trouble?
Thanks
I have tried to install Orange new rom on my qtek 9000, but I get country id error. I have tried to use the "MaUpgradeUt_noID.exe" but i still get the country id error. I have also tried to install the new rom from the bootloader, but not with any luck...
Please help a newbie...
When you run the MaUpgradeUt_noID.exe did you try it straight away again.
I have found when using this tool i get the country id error but then i rerun the MaUpgradeUt_noID.exe and it then goes through
I have tried to use MaUpgradeUt_noID in the bootloader and when it's in windows. But when I have it in bootloader, windows wont make a serial connection....
I did waht you wrote, and it is updating now... thanks...
My excalibur is not original locked, i want to upgrade to wm6, but when i try to upgrade, i got a message error `[244].
Is not possible to upgrade if the phone is not a t-mobile dash?
Thanks
Run the installer again once you get that error message. Should be fine.
i think doesnt works, the same message error; invalid model....
thanks
Ahhh, invalid model ID! Sorry, I must have misunderstood... You need to download the bootloader upgrade first.
ftp://xda:[email protected]/smartphones/Excalibur/RUU_Excalibur_SPL-1.11_UpgradeOnly.exe
Run that and then try upgrading.
I don't know where that bootloader downgrade came from but whoever did it deserves a medal.
Allowed me to go from T-Mobile WM6 back to HTC s620. Without it, I'd have been screwed.
-Mc
same result
with spl-1.11 upgrade only same result, id error.... any solution?
Thanks a lot.
Hi,
as far as I know the only way is to unlock your phone with http://www.imei-check.co.uk
Newchurch
fernandet1 said:
with spl-1.11 upgrade only same result, id error.... any solution?
Thanks a lot.
Click to expand...
Click to collapse
if this Update SPL 1.11 also doesn't work you'll have to unlock with IMEI-check and do this steps
but my pne is free
my phone is free, i have shop without any operator, original unlocked.
Thanks
it coud works with the modifid update with imeicheck?
I have modified these two parameters, but i have not unlock code because my htc-620 is original unlocked.
thanks in advance
The unlock which is necessary is to set the phone in "engineering mode" so that it accepts every ROM. This has nothing to do with SIM or net lock.
IMEI check sets your phone into that mode to remove SIM/net lock.
So it's a 2in1 unlock.
So even your phone accepts every SIM you have to unlock it to this engineering mode with IMEI-check. ATM there is no other known method to do this.
then, i need to send my imei to imeicheck to unlock in order to access to the engine mode?
Thanks!!
i have tried a method posted somewhere that you use the DASHUnlock and RUUUpgrade program to write any rom to your phone.. Now when i insert SIM from another carrier, says something like FATAL ERROR. Data Crashed, contact your service operator
is there a way to fix it? (obviously im in research status, so if there isnt a answer, im goin to keep looking
also i've been experimenting with the SPL_1.11 alternate bootloader and now my Tmo Dash says at startup
(Tmo splash)
Excalibur PV
SPL 1.11 SPE MFG
(what means this? is bootloader corrupted?)
BR!!
I was guessing that the fatal error message is something designed by IMEI-check to prevent people using their bootloader for free.
Somewhere at the end of those instructions would have been a statement telling you not to worry about the datacrash error, and just re-unlock your phone. worked like a charm on my htc 620
how you relock your phone??
and.. i flashed the original T-Mobile ROM WM5 but phone still saying the same thing..
I have been searching the net and the forums on help how to do this. Most of what I have found is specific for the HTC and T-mobile dash models, but not seen anything for the orange SPV E600.
I have unlocked the phone with Dashv2unlock program I bought, and tried "RUU_Excalibur_SPL-1.11_UpgradeOnly" and then tried "RUU_Excalibur_TMO_US_1.22.531.4_4.1.13.34_02.79.90_Ship"
Both of these give me a INVALID ID error.
I am suspecting my phone has only been SIM-unlocked (I can use my O2 sim card), but not CID-unlocked? I thought these programs do both?? Do I need a separate program to CID unlock?
Is this a problem specific to the orange SPV E600?
What am I doing wrong????
You phone is CID Locked,
Unfortunately, there's still no free way to CID Unlock an Excalibur, CID Unlock your phone here (USD 38.00):
http://www.imei-check.co.uk/
da_mayhem said:
You phone is CID Locked,
Unfortunately, there's still no free way to CID Unlock an Excalibur, CID Unlock your phone here (USD 38.00):
http://www.imei-check.co.uk/
Click to expand...
Click to collapse
original poster said he/she bought the Dashv2unlock program !!! ... which is a free program that works on the "PAID" UNL file for the specific IMEI ...
http://www.imei-check.co.uk/dashunlock.php
therefore ... I think that the unlocking procedure wasn't done correctly ...
just my $0.02
UnicornKaz said:
original poster said he/she bought the Dashv2unlock program !!! ... which is a free program that works on the "PAID" UNL file for the specific IMEI ...
http://www.imei-check.co.uk/dashunlock.php
therefore ... I think that the unlocking procedure wasn't done correctly ...
just my $0.02
Click to expand...
Click to collapse
LOL, that's what i get when i don't get to read and understand the query.
I agree, unlocking procedure wasn't done correctly.
Thanks guys. I actually went through www.imei-check.co.uk before, and as you correctly pointed out I bought a .unl file specific to my IMEI code, went through the screens just like shown on the website but although my phone will now take my O2 sim, it is still giving me an INVALID ID.
Has anyone succesfully done this with an SPV E600??
Is there a step missing somewhere? I read somewhere about having to run the unlocker program twice, which I have tried with no luck still.
Yay it works!
Ok, just to update.
I managed to update my rom to with the "RUU_Excalibur_HTC_RUS_1.24.411.1_4.1.13." rom instead and this was without having to flash a bootloader to begin with.
So if there are any SPV E600 users out there, the above rom works VERY VERY WELL.