Develop Bugs

Is it possible to Upgrade my Enligsh Jasjar to Chinese?

I just found a Cheinese Rom in the FTP, and using the "MaUpgradeUt_noID" it seems can detect my rom version, but i did not continue because i can not afford to "Fail", DID anyone know how to upgrade my english ROM to chinese???
HELP!!!!!!!!!!!!!!!

ericcc said:
I just found a Cheinese Rom in the FTP, and using the "MaUpgradeUt_noID" it seems can detect my rom version, but i did not continue because i can not afford to "Fail", DID anyone know how to upgrade my english ROM to chinese???
HELP!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
should be no problem for that , you can look at FTP again there had new ROM 11336_11334_10402 that's same as I had Dopod 900 , I already try to flush WEE i-mate ROM and flush back Dopod ROM twice no problem for flush ,

how can you upgrade it? need to enter serial mode? ( how to enter for universal) what tool did you use?
thx

ericcc said:
how can you upgrade it? need to enter serial mode? ( how to enter for universal) what tool did you use?
thx
Click to expand...
Click to collapse
See here maybe help http://wiki.xda-developers.com/index.php?pagename=Universal_Technical

I did the upgrade from Jasjar WWE to Dopod CHT. Here is how I did it:
1. Connect JJ to ActiveSync thru USB and wait till the sync session is completed.
2. While the sync is still active, I ran MaUpgradeUt_noID.exe. After a few steps of checking, it will disconnect ActiveSync and put the JJ into the bootloader mode.
3. The upgrade will halt with a country code error. No upgrade has been performed yet.
4. Run MaUpgradeUt_noID.exe again while the cable is still connected and JJ still in bootloader mode. I was prompted that I am upgrading from [Blank] to [NewVersionNumber]. Click "Next".
5. The ROM will be upgraded this time till it's done. It took about 20 minutes.
6. I pressed both softkeys and reset. When the reset prompt comes up, I pressed "0" to reset to default factory settings. After some booting time, JJ starts to speak Chinese.
I upgraded to Chinese ROM because the Chinese plug-in I used to use for English ROM is kind of buggy on WM5. Thanks to everyone on this forum.

There are a few things I did after I upgraded to CHT ROM:
1. Changed the system font to the more artistic Kai font (from KAIU.ttf on a Windows machine). The original system font was MingLiU, which looked kind of scrawny on a VGA screen.
2. Re-enabled ClearType for the system and PIE. For some reason, Dopod disabled ClearType settings so the user cannot turn on ClearType from the user interface. I used a registry editor and modified a few keys to get the ClearType feature back.
With the Kai font and ClearType, the screen becomes a lot more readable and very pretty! If someone is interested in step-by-step instructions, let me know, and I will post them.
By the way, I was so excited when I discovered the im.tv site actually works for me in USA. I was able to watch the TV news in Taiwan in full VGA screen.
One difference I noticed is that with the WWE ROM, I can very easily set up Bluetooth ActiveSync. With the CHT ROM, the device can only discover the serial port service on my computer, but not recognize its ActiveSync capability. If someone knows how to correct this, please let me know.
Also, in case you don't know, the keyboard mappings between WWE and CHT ROMs are slightly different. The SYM key is swapped with the ";" character, probably because SYM is hardly used in Chinese input. The shortcut "FN + ;" can toggle the English and Bomopofo modes. Note the ";" character is now on the SYM key of JASJAR.

yyl said:
There are a few things I did after I upgraded to CHT ROM:
1. Changed the system font to the more artistic Kai font (from KAIU.ttf on a Windows machine). The original system font was MingLiU, which looked kind of scrawny on a VGA screen.
Click to expand...
Click to collapse
Hi yyl :
Can you tell me how to change system front to Kai ?
Thanks

1. Copy KAIU.ttf from a Windows machine. Paste it into the Pocket PC's "Windows" directory thru ActiveSync.
2. Using a registry editor (like PHM RegEdit), BACK UP your registry first! Then go to "HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\FontLink\SystemLink\". Change the data of "Courier New" and "Tahoma" keys to "\windows\KAIU.ttf,DFKai-SB".
3. Soft-reset your device. Now all the Chinese characters become Kai font. It is not very smooth, because ClearType is still disabled.
4. To enable ClearType, this is how I did it. Maybe some steps are not really necessary.
5. Using the same registry editor, search for the keyword "cleartype" in all the keys and values. I found three matches. I set ClearType=1, NoClearType=0, ClearTypeText=1 respectively.
6. Soft-reset your device. You will see that the system ClearType is still disabled. Go to "Settings -> System -> Screen -> ClearType" to enable ClearType. This option was originally hidden from end users. Now it's visible. Once you check the "Enable ClearType" box, the font will immediately smooth up.
That's it. One thing worthy of note is, KAIU.ttf seems to only have traditional Chinese characters, not simplied Chinese. I am not sure.

Thanks yyl , I will try it today

yyl said:
I did the upgrade from Jasjar WWE to Dopod CHT. Here is how I did it:
1. Connect JJ to ActiveSync thru USB and wait till the sync session is completed.
2. While the sync is still active, I ran MaUpgradeUt_noID.exe. After a few steps of checking, it will disconnect ActiveSync and put the JJ into the bootloader mode.
3. The upgrade will halt with a country code error. No upgrade has been performed yet.
4. Run MaUpgradeUt_noID.exe again while the cable is still connected and JJ still in bootloader mode. I was prompted that I am upgrading from [Blank] to [NewVersionNumber]. Click "Next".
5. The ROM will be upgraded this time till it's done. It took about 20 minutes.
6. I pressed both softkeys and reset. When the reset prompt comes up, I pressed "0" to reset to default factory settings. After some booting time, JJ starts to speak Chinese.
I upgraded to Chinese ROM because the Chinese plug-in I used to use for English ROM is kind of buggy on WM5. Thanks to everyone on this forum.
Click to expand...
Click to collapse
Can anyone give me more detailed information about how to use MaUpgradeUt_noID.exe? When I run it, I get an error message: "This application has failed to start because RUU.dll was not found. Re-installing the application may fix this problem", any help will be appreciated! I'm trying to update my Jasjar to CHT ROM.

yyl said:
I did the upgrade from Jasjar WWE to Dopod CHT. Here is how I did it:
1. Connect JJ to ActiveSync thru USB and wait till the sync session is completed.
2. While the sync is still active, I ran MaUpgradeUt_noID.exe. After a few steps of checking, it will disconnect ActiveSync and put the JJ into the bootloader mode.
3. The upgrade will halt with a country code error. No upgrade has been performed yet.
4. Run MaUpgradeUt_noID.exe again while the cable is still connected and JJ still in bootloader mode. I was prompted that I am upgrading from [Blank] to [NewVersionNumber]. Click "Next".
5. The ROM will be upgraded this time till it's done. It took about 20 minutes.
6. I pressed both softkeys and reset. When the reset prompt comes up, I pressed "0" to reset to default factory settings. After some booting time, JJ starts to speak Chinese.
I upgraded to Chinese ROM because the Chinese plug-in I used to use for English ROM is kind of buggy on WM5. Thanks to everyone on this forum.
Click to expand...
Click to collapse
Can you give me more detailed instruction about how to use MaUpgradeUt_noID.exe? Every time I run it, I get an error message as follows: "This application has failed to start because RUU.dll was not found. Re-installing the application may fix this problem."

yyl said:
I did the upgrade from Jasjar WWE to Dopod CHT. Here is how I did it:
1. Connect JJ to ActiveSync thru USB and wait till the sync session is completed.
2. While the sync is still active, I ran MaUpgradeUt_noID.exe. After a few steps of checking, it will disconnect ActiveSync and put the JJ into the bootloader mode.
3. The upgrade will halt with a country code error. No upgrade has been performed yet.
4. Run MaUpgradeUt_noID.exe again while the cable is still connected and JJ still in bootloader mode. I was prompted that I am upgrading from [Blank] to [NewVersionNumber]. Click "Next".
5. The ROM will be upgraded this time till it's done. It took about 20 minutes.
6. I pressed both softkeys and reset. When the reset prompt comes up, I pressed "0" to reset to default factory settings. After some booting time, JJ starts to speak Chinese.
I upgraded to Chinese ROM because the Chinese plug-in I used to use for English ROM is kind of buggy on WM5. Thanks to everyone on this forum.
Click to expand...
Click to collapse
Thanks! I am Upgrading my ROM now, May the God bless me!

Upgrade Success! thx everyone's help!

yyl :
Can you upload KAIU.ttf which I can't find in my window machine, Are you used Chiese window system ? mine was English + language pack

The KAIU.ttf comes with many versions of Microsoft Office of many languages. When the Asian character support is selected during installation, Office will install some extra Asian fonts for you. This is one of them.
Anyway, I uploaded this font to ftp://xdaupload:[email protected]/Universal
I don't know if this upload is appropriate. If it is not, the board moderators, please feel free to delete it. Thanks.
The principles that I outlined above should work with any TrueType Chinese font that you like.

johnney said:
Can you give me more detailed instruction about how to use MaUpgradeUt_noID.exe? Every time I run it, I get an error message as follows: "This application has failed to start because RUU.dll was not found. Re-installing the application may fix this problem."
Click to expand...
Click to collapse
Download "(Open_ch)UNI_DOPOD_11336_134_10402_Test.exe" from the "Universal" folder of this site (see the link in my previous post). Use Winzip to extract all the content from this EXE file into a folder on your hard drive. Place "MaUpgradeUt_noID.exe" into the same folder. Then perform the steps I mentioned above.

I have Modify the font to KAIU , But it does not suppurt Simpfy Chinese, it only support tradition chinese, does any font will fit Both?

I did it!
yyl said:
johnney said:
Can you give me more detailed instruction about how to use MaUpgradeUt_noID.exe? Every time I run it, I get an error message as follows: "This application has failed to start because RUU.dll was not found. Re-installing the application may fix this problem."
Click to expand...
Click to collapse
Download "(Open_ch)UNI_DOPOD_11336_134_10402_Test.exe" from the "Universal" folder of this site (see the link in my previous post). Use Winzip to extract all the content from this EXE file into a folder on your hard drive. Place "MaUpgradeUt_noID.exe" into the same folder. Then perform the steps I mentioned above.
Click to expand...
Click to collapse
Thanks for your help! Now I did it! My mistake was that I copyed the whole exe file to the folder!
Do you guys have Wisbar Advance 2 installed? How's it work? It really slowed my system down on my previouse english ROM.

Re: I did it!
johnney said:
Thanks for your help! Now I did it! My mistake was that I copyed the whole exe file to the folder!
Do you guys have Wisbar Advance 2 installed? How's it work? It really slowed my system down on my previouse english ROM.
Click to expand...
Click to collapse
I use Magic Button to "truly" close applications. It also shows battery meter and the icons of currently running apps.

ericcc said:
I have Modify the font to KAIU , But it does not suppurt Simpfy Chinese, it only support tradition chinese, does any font will fit Both?
Click to expand...
Click to collapse
Yes, as I mentioned in one of my previous posts, KAIU.ttf seems to include only traditional Chinese. The MingLiU font that came with the Dopod ROM has both traditional and simplified. I presume there are many third-party fonts on the market that support both. Note that fonts supporting both styles tend to occupy a lot more space.

1.40.00 Asian WWE O2 ROM GPRS Glitch

I found a glitch I've been trying to work around. I use an XDA IIs from O2 with the current Asian WWE O2 ROM in English ;-). Well if I connect to GPRS and use the internet for whatever amount of time I need it for, and disconnect, connect again, and disconnect, it will eventually freeze up the connection when I try to connect again. Either way after like 3 GPRS usages I must softreset in order to connect to GPRS, anyone have this same problem? I would like WM5 but I've upgrade and downgraded 4 times, its just not for my phone, its too slow even with overclocking.

i had the same problem~
and found this as the solution from somewhere in the search
PeterW said:
Here is a step by step instruction:
1. Download the older version of caller-id from:
ftp://xda:[email protected]/BlueAngel/CAB_Files/Caller ID/IA_CallerID_1.20_WWE.CAB
and transfer it over to your device. Any directory is OK. I used ActiveSync to put it into the My Documents folder.
2. Remove the file IA_CD-Startup.exe from \Windows\Startup on your device.
3. Rename iacontacts.dll to something else (e.g. old-iacontacts.dll). This file is in the \Windows directory of your device but is hidden. However you can rename it using your PC. Open Windows explorer, and navigate to Mobile Device>My PocketPC>Windows.
4. Rename displayCID.dll to something else (e.g. old-displayCID.dll). Access it via your PC the same as for the previous step.
5. Soft reset
6. Run the CAB file on the device - just tap on it.
7. Soft reset.
That should do it.
- Peter
Click to expand...
Click to collapse

Hi there,
I posted a problem today that doesn't sound quite like the one above.. but maybe it is... please read my post (don't want to make a mess by posting here too) and let me know if you think the caller id could the issue.
Thanks.
http://forum.xda-developers.com/viewtopic.php?p=181358

Hi there,
following my reply on the other thread, I found this one & followed the instructions. Since then I can always connect & disconnect GPRS and never need to use flight mode to re-activate GPRS

weasel said:
Hi there,
following my reply on the other thread, I found this one & followed the instructions. Since then I can always connect & disconnect GPRS and never need to use flight mode to re-activate GPRS
Click to expand...
Click to collapse
So far... soooo good. Strange that caller id would cause the issue. I also downloaded a "Keep your GPRS connection alive" app from another posting. That may be helping as well. Either way, no headaches thus far.
Thanks!

XDA Exec PHM regedit won't load

Has anyone else had this problem:
I've downloaded the PHMregedit msi from phm.lu (the activesync desktop installer version) and installed it in the same way as every other add-on, i.e. just double click the msi.
It installs to the desktop machine OK and it pulls up the ActiveSync installer as per normal BUT regedit does not appear on the ActiveSync "programs to install" list.
If I OK the install dialog then the install finishes up as normal but there is no "please check your mobile device for any additional required steps" message and the software is not installed on the XDA.
Everything else that I try installs fine.
Is there some other step I should be doing or is there a problem here?
Thanks
Pete

I just use the CAB file. Here it is:

Drag cab to my device/Documents/ run cab... then I get "unsuccesfull"
Any ideas?

RE
Why don't you try another FREEWARE registry editor, Tascal Registry Editor (TRE), here:-
http://www2r.biglobe.ne.jp/~tascal/download/pocketpc/tre_e.htm
It works well on my QTEK9000 aka Universal

Also read http://www.pocketpcmag.com/blogs/menneisyys/UltimateRoundupOfRegistryEditors.asp

Thanks Guys... Should keep me busy for a while/

FWIW, I just had the exact same problem with PHM Registry Editor. It would load up just like another program, launch the ActiveSync program loader, but then nothing would appear on my 8525. I tried soft booting a couple of times and various other combinations with no results...
However, dragging the CAB file to my storage card and then running it from the unit seemed to do the trick. Thanks for posting that cktlcmd!
cktlcmd

unable to update hx4700 2003 - MW6 using Bootloader!

I've read good reviews on chrismrulz's bootlaoder programe and I'm trying to use it to update my iPAQ 4700 from 2003 to WM6. However I am obviously doing something wrong as I just cannot get it to work!
Please can anyone offer any advice?
I hope I am following the exact instructions as mentioned here at http://forum.xda-developers.com/showthread.php?t=325727
and here is what is happening:
Step 1.
Make new folder in root directory.
No Problem c:\Bootloader set up.
Step 2.
Download WM6 ROM and bootloader into file.
Done as directed from links in instructions directly into new folder.
Checked and c:\Bootloader now has 2 files in it Bootloader.exe and WM6_4700_0_7_0_RELEASE4.rar
Step 3.
Put hx4700 in bootloader mode and place in sync cradle.
I assume I have done this correctly. Screen goes blank and you can just make out the HP logo it says USB when in cradle and shows version 1.01
Step 4.
Open bootloader and select image.
Ok I go to folder and double click on Bootloader.exe
I get a security warning about the software and ignor by pressing run.
2 things now happen simutaniously. Bootloader.exe expands and creates c:\Bootloader\Bootloader and fills it with more files and directories and....
I get a box asking me to select a file to flash ROM to my device. I change the directory back to C:\Bootloader and select WM6_4700_0_7_0_RELEASE4.rar and press open.
I get a message telling me to please wait the file is being extracted and inviting me to press ok. Before I can press ok the box is replaced with a winRAR Diagonistic Message saying c:\Bootloader\WM6_4700_0_7_0_RELEASE4.rar no files to extract.
I close this dialog box and get another message telling me to wait whilst it edits files. Then this in turn is replaced by a message saying Error reading file c:\Bootloader\Bootloader\temp_nbf\ I click on OK to acknowledge.
And that’s it nothing else happens.
I've obviously read the instructions wrong or something can anyone help point me in the right direction? Or offer any alternatives?
I'm using Active Sync 3.7.1
Thanks
Phil

Open the rar file (with WinRar), and read the instructions that are in the Readme.txt file... And update your Activesync to version 4.5, which is needed for WM6.

Excellent,
Thank you Ridolfo, so much easier than what I was trying to do. I now have WM6 working and am very pleased with it.
One problem i now have is Activesync 4.5 will not work with my Outlook 2002 I dont suppose anyone knows a workaround or do I have to buy a copy of Outlook 2007?

Phil3099 said:
Excellent,
Thank you Ridolfo, so much easier than what I was trying to do. I now have WM6 working and am very pleased with it.
One problem i now have is Activesync 4.5 will not work with my Outlook 2002 I dont suppose anyone knows a workaround or do I have to buy a copy of Outlook 2007?
Click to expand...
Click to collapse
Very strange indeed, my AS works fine with OL2002... Did you use the MS Office Update to get the latest servicepacks for OL ?
Dirk

Outlook 2002 now ok. I was havinag a bad day yesterday. Now if I can just find a way of viewing java enabled web pages I will be happy

Phil3099 said:
Outlook 2002 now ok. I was havinag a bad day yesterday. Now if I can just find a way of viewing java enabled web pages I will be happy
Click to expand...
Click to collapse
Try these .....
First install JBed, then Opera
Cheers
Dirk

Hi Dirlan,
Thank you for the files. I was already experimenting with Opera so I deleted it from my iPAQ loaded Cloudyfa_EsmertecJbed.cab and then reinstalled Opera.
Unfortunately I get an error message from Jbed saying "the file jbed cannot be opened. Either it is not signed or one of its components cannot be found.
Any ideas?
Phil

After extracting using WinRAR

Trying to upgrade from 2003 to WM6 ...
After extracting WM6_4700_0_7_0_RELEASE4.rar using WinRAR I am trying to follow the instructions in the readme.txt (as Bootloader didn't work for me as in the first post in this thread):
From readme.txt
To begin with if you want to flash your device using cradle,you have to:
1.In processes (CTRL+ALT+DEL) you must kill Wcesscom.exe
2.Then Enter in Bootloader (Contacts+iTask+Reset)
3.Put your device on usb cradle.
4.Run mtty11a.exe
5.In "Port" choose \\.\WCEUSBSH001 and click OK
6.Write command: lnb OS_WM6.nb0
7.Wait
8.Enjoy yourself
As I'm not all that familiar with this can someone explain in step-by-step what's involved with the mtty11a.exe application, and Step 6?
Currently my hx4700 is what I think in bootloader mode (Screen is dim an I can barely make out "USB" the hp logo and the current version "v1.01"). I previously tried the original WM5 upgrade and it just dies on me at 0.1%.

Hi tk2000
As I posted the original post I know exactly what you are going through. However once I went through the instructions you are currently trying to use every thing went smoothly. You have extracted the .rar file and are unsure of the mtty11a.exe file.
Assuming you have you have killed Wcesscom.exe on your pc as in step 1,
and the device in in its cradle in bootloader mode (as you described very faint HP logo, USB and version 1.01 displayed).
Then double click on the mtty11a.exe as in step 4. This then brings up an application and you will see a dropdown menu next to port, simply select the option \\.\WCEUSBSH001 and click ok.
6.Write command: lnb OS_WM6.nb0 now this stage I was a little unsure of myself I simply typed "lnb OS_WM6.nb0" in from the keyboard and pressed enter and it started to load. This takes a few minutes but afterwards you should have WM6 on your device.
I had to do a couple of hardware restarts and it took a few minutes in its cradle but it all works fine for me.

Phil3099 said:
Hi Dirlan,
Thank you for the files. I was already experimenting with Opera so I deleted it from my iPAQ loaded Cloudyfa_EsmertecJbed.cab and then reinstalled Opera.
Unfortunately I get an error message from Jbed saying "the file jbed cannot be opened. Either it is not signed or one of its components cannot be found.
Any ideas?
Phil
Click to expand...
Click to collapse
Hi Phil,
There should be an 'opera-unsigned*.cab' somewhere here on the forum. I didn't try it because Opera works fine for me.
Sorry
Dirk

Phil3099, I a followed the instructions exactly but I don't see a status bar on the pda. mtty showes the progress with lines of + but the 4700 stays on the hp logo screen with USB on top.

Will the Windows Mobile 6.1 upgrade work on a Unicel HTC S621?

Hello,
I am new to this forum, and I have read through a lot of the links and threads about this, but I have not found the answer to my question. Will these ROM Updates work on a HTC S621 that I have through Unicel? The phone is unlocked, but I dont know if that means that I still have to download the file that will unlock my phone? I am very interested and eager to upgrade my pnone to Windows Mobile 6.1, but I am honestly afraid that my inexperience with doing something of this nature will "brick" my phone and I will be without a phone. It irrates me to no end that neither HTC or Unicel are going to bother to come out with an official update for this phone, so if I want the lastest update to the phone, I have to go through unofficial channels. Could someone please tell me if this will even work for my phone before I try to do it? Thank you
Larry

Yes it will work sir, just follow the tutorial and upgrade... The tutorial is linked below in my signature... Also, as a beginner I would recommend using Ricky's rom version 24. ... if you need any help let me know okay... also, make sure you run connection setup after the upgrade...

Am I going to have a problem, or should I do something different since the instructions seem to be written for a phone on T-Mobile? I am really fretting about bricking my phone and I dont know if Unicel will do anything for me if I happen to brick the phone because I did something wrong. I would really like to try flashing the ROM on the phone to Windows Mobile 6.1, but I am just nervous, I guess. Thanks for the help and wish me luck
Larry

You should be fine if you read it over (print it out) and can follow directions. The main problems people run into are keyboard layouts and 270 errors.
No Guts No Glory

pfunkside said:
You should be fine if you read it over (print it out) and can follow directions. The main problems people run into are keyboard layouts and 270 errors.
No Guts No Glory
Click to expand...
Click to collapse
Yah exactly just read and follow instructions word for word...

nobody on this site can promise that nothing will go wrong, but it is usually determine that when something does go wrong, it is because the instructions were not being followed.
you sound a little too nervous to me to be trying this, you may want to either find someone else to do this for you, or take a deep breath, have a beer, and then dive in.
i've done this three times without an issues.

I did it to my unicel S621, and works wonderful! pm me if you need the internet settings after...

He will definitely need the internet settings... for sure...

yes, I need the internet settings please. also, how do I get rid of the "fav5" thing off the phone?
Thanks
Larry

larry.twichell said:
yes, I need the internet settings please. also, how do I get rid of the "fav5" thing off the phone?
Thanks
Larry
Click to expand...
Click to collapse
which version are you using? which rom version (i.e. are you using Rickys or Kavana's)
If you are using Ricky's go all the way down to the last thing on the homescreen which should be settings... and then scroll to the right to Chome settings and then in there you can unclick everything you do not like... everything that is bolded will show up on your homescreenv and everything not bolded will not show up..... then restart your phone and you should be on the go...

Hello,
Okay, I have successfully installed "Ricky's" ROM. I followed the steps to the letter in the newbie thread. I installed the keymapping .CAB file. My phone needs the Unicel Internet settings. I have once before reset my phone back to factory specs, which required that I have to go into the local Unicel store and get the internet settings and install them, the problem now is that I could use Wi-Fi to access the internet before with my phone, even though I couldnt through my data plan/cell service. Since I updated the ROM, I cannot even access the new through Wi-Fi. In the instructions, it states that you should run the connection wizard, but the problem is it only lists T-Mobile, AT&T, and Carolina in my phone, not Unicel. I know that the GSM partner of Unicel was bought by AT&T, but I dont want to set my phone to that because I dont know if it will screw everything up if I do.
So what advice can you offer me? Will getting the Internet Settings from Unicel or member Outragis solve all of my problems? Thank you for any suggestions! By the way, I Love the new Windows Mobile 6.1, now I just have to learn how to use it!
Thank You,
Larry

larry.twichell said:
Hello,
Okay, I have successfully installed "Ricky's" ROM. I followed the steps to the letter in the newbie thread. I installed the keymapping .CAB file. My phone needs the Unicel Internet settings. I have once before reset my phone back to factory specs, which required that I have to go into the local Unicel store and get the internet settings and install them, the problem now is that I could use Wi-Fi to access the internet before with my phone, even though I couldnt through my data plan/cell service. Since I updated the ROM, I cannot even access the new through Wi-Fi. In the instructions, it states that you should run the connection wizard, but the problem is it only lists T-Mobile, AT&T, and Carolina in my phone, not Unicel. I know that the GSM partner of Unicel was bought by AT&T, but I dont want to set my phone to that because I dont know if it will screw everything up if I do.
So what advice can you offer me? Will getting the Internet Settings from Unicel or member Outragis solve all of my problems? Thank you for any suggestions! By the way, I Love the new Windows Mobile 6.1, now I just have to learn how to use it!
Thank You,
Larry
Click to expand...
Click to collapse
Yes just private message that guy that said has the Unicell internet settings as you will need them in there and especially for receiving MMS (picture messages)... so just ask him to give them to you and I bet he will be more than happy to provide you with them.

I did PM him, I hope to hear back from him soon. I Imagine I would need to use Active Sync at home to download the updates to my phone.
Thanks for the help and advice, I am really liking the new interface!
Larry

I need Help!
Okay, so I am trying to find the files I need so that my HTC S621 that I have through Unicel to work and connect to the internet. I have contacted Unicel and they sent me a link to a file, and this is supposed to work, but it doesnt.
Here is the email:
Subject: Doing a Hard reset on the HTC621 will remove all Unicel settings
Issue/ Findings:
After doing a hard reset on the HTC S621 you will no longer have any Unicel settings and will need to reinstall them for WAP and MMS. To hard reset the HTC S621 (with the HTC S621 powered OFF) press and hold the 2 soft keys and than press the power button. Do not let go of the soft keys until you see the message to reset your HTC by pressing the send button.
Resolution:
The setting can be reinstalled into the HTC S621 by using a CAB file and a Micro SD card. The File has been posted on the internet and can be installed 2 ways.
Option 1: Active sync
From your PC go to http://www.unicel.com/devices/htsc621.html and download the zip file to your PC. Open the zip file and extract all the files within to your PC. Once this is done you should see the folder 2577 on your PC. Now connect your HTC S621 to your PC (you will need ActiveSync for this part and a memory card) and open Explore. Open “My windows mobile-based device”. Now drag or copy and paste folder 2577 from your PC to “Storage Card”. Once this is complete, unplug your device from your PC and power-cycle your device. After waiting a few seconds, you will get a prompt to do an auto-configure, press yes and your files will be installed. Once the auto-configure is complete, you will be asked to do a restart. Press yes to restart and all the settings the device had at the time of purchase should now be on the device.
After the device has power cycled, a change needs to be made to the GPRS Authentication to ensure connectivity. Please follow the steps below:
Start
Settings
Connections
GPRS
Unicel Info2Go
scroll to authentication type
CHAP
Done
End
Option 2: SD card reader
From your PC go to http://www.unicel.com/devices/htsc621.html and download the zip file to your PC. Open the zip file and extract all the files within to your PC. Once this is done you should now see the folder 2577on your PC. Now open your SD reader, with your memory card installed in the reader, drag the entire 2577 folder to the SD card. Once this action is complete, install the SD card into the S621 and turn on the device. After waiting a few seconds, you will get a prompt to do an auto-configure, press yes and your files will be installed. Once the auto-configure is complete, you will be asked to do a restart. Press yes to restart and all the settings the device had at the time of purchase should now be on the device.
After the device has power cycled, a change needs to be made to the GPRS Authentication to ensure connectivity. Please follow the steps below:
Start
Settings
Connections
GPRS
Unicel Info2Go
scroll to authentication type
CHAP
Done
End
Okay, so I downloaded the file and did what it said, but it is not auto running the file and doing anything. Is this because I upgraded the ROM and the file will not work with Windows Mobile 6.1? I am getting a little flustered and I love the new OS, but I would like to be able to use the internet on the phone. I cant even connect to the internet through Wi-Fi.
Does someone have the correct setting file for a Unicel HTC S621 that I could have to get my phone working right? I would appreciate it!
Thank You
Larry

Couldn't you just add them manually
Start - settings - then each add settings...
I'm surprised Unicel doesn't make them easier to access
This link might help but your easiest bet is getting the guy who commented to read you his.
http://www.howardforums.com/showthread.php?threadid=655672

Running out of memory?
I recently did the Kavana 6.1 upgrade on my Unicel/AT&T HTC S621. Everything is working fine except that the phone is constantly running out of memory (Which, actually, is not really fine...) Using the Free Memory app doesn't really work, as it will free only a KB or so, and it doesn't show the correct amount of RAM, in any case (usually around 5K instead of the 64K actually ob board). Any ideas?
Oh yes, and also, the phone now calls itself a C720W, which is a Dopod (Asian carrier) version of the S621... Anyone else?
Thanks,
John