Related
I tried the Upgrade, but it did never start, so when I tried to get it back to normal, doing a reset, I only get the Bootloader screen, with the USB and v0.60, I tried a Soft and Hard Reset but nonthing, I have tired to re-flash it again, but also nothing, please any help, thanks
I can not even to start the Flash program, I get ERROR : 101
ERROR 101 : CONNECTION ERROR
PLEASE ANY ADVICE IS WELCOME, THANKS
I WAS ABLE TO REFLASH IT, BUT I STILL GET TO BOOTLOADER ONLY
PLEASE HELP
latest ActiveSync installed? Removed battery?
Had this issue Yesterday. Even if You update the ROM, You will still stay in bootloader (for me it was like this). Do another update, this time only the radio (so delete ms_.nbf and nk.nbf from the directory from where You run your upgrade utility). After this (another 20 minutes) You should be able to have result after the cold-reset.
On the bootloader there is a small difference. Upgrading the ROM shows how far he actually is (in percentage), whilst upgrading Radio it does not show You the percentage, only that he is busy.
Ruud
Just try the update without any insert card (sd and sim), and a wonder will happen!
Teja
- connect the JASJAR with your PC using the USB cable. Activesync will NOT start and the XP says does recognize it
- do a HardReset (press the 2 (-) in the keyboard and softrest it all at the same time. Hardreset screen appears (DON'T press 0 or X..)
- start the update program. Please use a good upgrade like the latest from imate ftp://ftp.clubimate.com/JASJAR_WWE_11353_137_10301.zip
- start the update and when it's looking to check the version of the JASJAR softreset it
It should start to reflash it without problems.
I hope it helps...
hi guyz need your help who ever was succesfull upgrading 2495B from WM5 to WM6. I searched and tried all methods that was posted in here. but no luck. I also tried this method :-
" worked for me. 2490 device was shipped w/wm5 1.02h
Please Note: As of 10/8/07 there are 2 confirmed working roms for hx2*** series ipaqs. So far the pdaviet version is more stable, less activesync issues, preinstalled software ie: psshutxp and much more. (could use more feedback from others on this)
As promised: Here are the steps
-take out any cf/sd cards you might have installed. grab your cradle AND ac power cord (no AC cord = no flashing for you)
-put device into normal boot loadermode and downgrade to 1.0h w/files from hp website.
-format the p.s. (fyi everyone misses you have to HOLD DOWN the keys for p.s. format for like 4 or 5 seconds and THEN it will activate) After p.s. format wm5 will start.
(!! Start below this line if you are performing a wm6-4pda to wm6-pdaviet upgrade or vise versa !!)
-put device into WHITE bootloader mode and again run the 1.0h rom setup. When you arrive at the screen that asks "update" or "cancel",
1. rename the wm5.xxx.nbf to wm5.xxx.nbf.old
2. rename the new wm6.xx.nbf from the 4pda.rar/pdaviet file to whatever your wm5-wm5.xxxx.nbf was called (before you added the .old to it)
-NOW hit update. You shouldnt get any errors.
-After update wm6 wont start properly until you again format the p.s. (remember to hold down those keys to start) once this is done
-you should be golden.. with a working copy of wm6 on your wm5 deivce.
"
I have 1.02h in my pda, But i can not downgrade to 1.0h I am getting msg that " Image Low Version " Please help me upgrade to WM6
come on guyz !! No one
longhorn2006 said:
come on guyz !! No one
Click to expand...
Click to collapse
YOu dont need to downgrade, I have a 2490b and I coudlnt get the downgrade working either. I am now running viets wm6
try this
try the universal bootloader method
http://forum.xda-developers.com/showthread.php?t=329079&page=16
I'm running Vista and when I wanted to run the bootloader upgrade on my Dash I kept getting this message error. Error 260. anybody find any way around it? I've tried to manually set th ephone into bootloader mode, same result. help!! PS the error is supposed to mean "port already open" or "open port error" I'd really appreciate any help!
erro 260 - fixed
switches to my wife's laptop that had XP on and it worked like a charm. I'd be glad to assist anybody in the process od de-branding their Dash. Removing the ugly T-mobile paint logo on the unit was easy too.
ERROR 260
Sorry for thislong story....
OK, I've been on looking around the site for a while. I installed the WM6 Beta. I was looking for two days for the WM5 ROM only because I want the little things to work. Finally found it. But now every time I try to flash my phone ack to WM5 bI keep getting the 260 connection error. The readme only says to restart the comp and phone and try again. I have literally, no joke, done this 12 times in the last 2 hours, hoping maybe it will go. All the phone does is go to the green, blue, and red screen and stays there. Then the comp says it gets the error. I know it's connected because Sync Center syncs, I can look through the phone, install apps from my comp, etc. Also I tried doing the 'Update only' rom for version 1.11 or so, and it starts to go but then says its the wrong version RUU. Has anyone had this problem before? Flashing to WM6 did this once and then worked after.
I'm running Vista Premium, stock sync cable, Microsoft Sync Center for vista. All this is the sameas when I flashed to WM6.
There goes another 3 attempts, trying to change timing, reinstalling Sync Center, etc.
Decided to try it on my XP desktop, and for some reason, first time it worked. Maybe Vista didn't like it? Who knows..
Mladito Vista!!
Hi there,
I have the same little problem here!!!! I have a laptop with Vista (garbage)... so i´ll try on a laptop running XP...thank you for posting this, it was a big help..i let you know how it turns out... see you around
WM5 to WM6 --> Problems at 3%
Hi all,
I've errors upgrading my phone to WM6.
I Can open the Wizard (it`s a generic to S620/S621), but in 3% i`ve an error.
I think thats my phone has a blocked CID.
How can i unlock this? i`ve tryed with tools to unlock, but without success...
Regards,
Emerson
Hello,
Welcome to the forum.
Your problem is that your phone is CID-Locked. Hence, you'd need to use a paid service to unlock it. I personally used the following service which provides instant unlocking:
http://www.gsmliberty.net/shop/htc-excalibur-instant-remote-unlock-p-1452.html
I used a credit card, it's 39.99 $ - I was done unlocking and upgrading to Windows Mobile 6 in about 15-20 minutes.
Good Luck !
P.S:
Steps to install WM6
- First CID/SIM Unlock using GSM Liberty
- Flash Bootloader
- Install WM6 ROM (It will take some time for it to load so give it about 5-10 mins. it does get stuck at the boot screen for sometime but eventually it'll load)
- Install Office/Audio Manager
- Application Unlock your phone using SDA Application Unlocker
- Install the necessary software/tweak/hacks
there you go, if you have any questions, feel free to ask. also, if you use the search function, everything's available here.
Good Luck !
Here's the following links you require
1) Flash Bootloader
ftp://xda:[email protected]
2)here's the WM6 ROM:
http://files-upload.com/files/472108....90_Ship.ex e
here's office for those who want it:
http://rapidshare.com/files/31706137/Office.WM6.zip
here's Htc Audio Manager for those who want it:
http://forum.xda-developers.com/atta...1&d=1183909664
Ps. I better like German flash, it's smaller due to fewer language packs, and contains English, here: http://files-upload.com/files/472422....90_Ship.exe
thanks to jsp_m for the links.
Hi,
I`ve problems because my IMEI is from Brazil...
And in the site accept only 15 digits IMEI..
My imei is: 35*************02 (17 Digits IMEI)
Thanks,
Emerson
hey,
that's not a problem. everyone has 17 digits, don't include the last 2 digits when you type in your IMEI so for example
11111111111111102
just include the first 15 and submit and you'll get an unlock link in your e-mail, follow that link, scroll down to the page to download dashunlock software and download the .UNL file for your IMEI and then make sure ur phone is connected to active sync and it's green, open the dash-unlock program and then hit enter then it'll ask for the .UNL file, locate it and open it and your good to go - your phone will be unlocked then soft reset it or i think it's automatic and everything's set.
good luck !
p.s: in other words, don't include 02 when you type in your IMEI.
HTC Audio Manager
http://forum.xda-developers.com/showpost.php?p=1355010&postcount=5
Thanks!
I'll Try NOW and let all know...
Regards,
Emerson
Arrghhh!!
My phone still give the message:
Invalid Model ID [244]....
And now? i`ve payed 40 bucks for an unlock software....
Thanks,
Regards,
tatarezende said:
Arrghhh!!
My phone still give the message:
Invalid Model ID [244]....
And now? i`ve payed 40 bucks for an unlock software....
Thanks,
Regards,
Click to expand...
Click to collapse
Emerson;
Read the second post from luckybandit on this thread. That´s exactly what to do to get rid of the "invalid model" issue. Download the bootloader, flash the phone, flash the new ROM and be patient.
My excalibur is also from South America, and worked OK. If you have any doubt just let it know to this thread.
Boa sorte!
Hi,
I`ve problems with the link of Boot loader....
Anyone can send the full URL?
Thanks,
Regards,
Emerson
Hello,
I'm sorry about the links not working, here - i've attached the bootloader for you. here's what you do
1) Run bootloader (attached file)
2) Run the WM6 WWE ROM
3) Run SDA Application Unlock
4) Install Office/Microsoft Voice Command/HTC Audio Manager
5) Install Tweaks/Hacks
here's a site that has some applications and tweaks:
http://mobile.surrealnetworks.com/DashApps.htm
and search this forum, there's tons of information, hacks - etc.
Good Luck !
oh by the way, did you unlock your phone properly?
1) Download unlock software
2) Download .UNL file specifically for your IMEI
3) Connect phone to computer and make sure the activesync's icon has turned green
4) Run unlock software
5) When unlock software asks for .UNL file, browse for it, choose it
6) That's it ! It should say Unlocking done and it'll reboot
Your phone is now Sim & Cid Unlocked. If you have more questions, feel free to ask. just do what i said first then post.
Good Luck ! Hope to see everything working for u...
Hi again...
Now i`ve the Error 260 message everytime my phone boots in "Flash mode" (3 color screen)....
Follow my configuration in this screen:
Excalibur Wi-Fi RUU
ONBL 1.15.0000
Excalibur
SPL 1.15.0000
Excalibur IU
ERROR [260] - No connection
tatarezende said:
Hi again...
Now i`ve the Error 260 message everytime my phone boots in "Flash mode" (3 color screen)....
Follow my configuration in this screen:
Excalibur Wi-Fi RUU
ONBL 1.15.0000
Excalibur
SPL 1.15.0000
Excalibur IU
ERROR [260] - No connection
Click to expand...
Click to collapse
Hi,
Are you using Windows Xp? Cause I've gotten that error a couple of times too but it was in Vista. Try Xp if you're using Vista.
Hi!!
DONE with XP.... but now i`m affraid!! The "Green Screen" with nem OS apparently locked... this is normal? at least 3/4 minutos in the same screen.. both "patches" are applyed sucefully....
Is there anything else to do now?
If anyone can help i have a hp ipaq h2200 and i tryed to do a bios update but now it`s stuck the onley thing that shows me is a image with hp,usb and v1.08 can anyone help me please?is there any way i can make it work again?is there any ROM for this kind of device maybe a wm5 or wm6?
no one can help me?
Profy_X said:
If anyone can help i have a hp ipaq h2200 and i tryed to do a bios update but now it`s stuck the onley thing that shows me is a image with hp,usb and v1.08 can anyone help me please?is there any way i can make it work again?is there any ROM for this kind of device maybe a wm5 or wm6?
Click to expand...
Click to collapse
go boot loader mode before upgrade
but how do i do this?it isn`t in bootloader?(it shows a hp image up shows usb and down v1,08)
...
First important question: what upgrade did you try to do?
For iPAQ h2200 there is no cooked ROMs: WM5 or WM6x. This device can work only under branded WM2003se.
If you tried to do upgrade to any of cooked ROM like WM6.0 from different device like hx22xx by mistake, please try the following:
1. Go to HP www page and download the last available ROM upgrade (I assume English ROM)
2. Turn on iPAQ (don't carry the device doesn't boot properly) and place it to the cradle which should be connected to PC which has installed active sync software (please don't carry about lack of connection seen on active sync).
3. Run the ROM upgrade.
If you tried the HP upgrade and it stuck - just repeat them with the way described above.
Important - do not use blue tooth connection during flash !!! Only USB !!!
Good luck.
If it doesn't help I believe there is hundred of similar cases described in forums - try to search the solution there
bigu1975 said:
This device can work only under branded WM2003se.
Click to expand...
Click to collapse
More precisely: WM2003 only - no SE upgrades for the h2210.
i upgraded the v1.10 original ROM from HP home site but now i solved the problem with mtty and ultra edith but now i have a nother problem i flashed again the ROM but its stuck on the loggin bar from startup it just fill the bar but windows doesn`t start i tryed again to flash and the problem still persist any sollutions?
Profy_X said:
i flashed again the ROM but its stuck on the loggin bar from startup it just fill the bar but windows doesn`t start i tryed again to flash and the problem still persist any sollutions?
Click to expand...
Click to collapse
As I understand you correctly - you restored your iPAQ into live using the last available ROM from HP site, which is WM2003 (thank you Menneisyys). The iPAQ worked fine and then you was trying to make another ROM upgrade - which ROM did you use?
I am asking because the ROM in version 1.10 is the most actual one and there is no any other ROM for this device. I assume that source of your problem is you are trying to use incorrect ROM. Correct me if I am wrong... If this is true - the solution is to restore your device into operational using the way as you did it before and stop to flashing your device - there is no another ROM to your iPAQ
the v1.10 but the problem is that after i flash the wm doesn`t start it just stay there stuck on the startup and i reflashed the device but still doesn`t start
how did u fix the stucked screen while booting? im searching for solutions for 30 mins now, but dind't find a way...
please help somebody..
ok, for those with "same" problems like me:
i have windows 7 64bit. the rom flashing wasn't successfull on this machine. i did the same on my notebook with windows xp and it worked. before it said that it couldn't find my ppc. on the notebook it wasn't a problem.
i had these installation notes found anywhere:
1.) Go to the Vendor Website, and...
2.) Select the appropriate hyperlink for your model.
3.) Download the most recent BIOS version.
4.) Press the POWER + iTASK + CONTACTS + RESET buttons at the same time so as to enter the FLASH Mode
5.) Make sure your USB connection to the Cradle is hooked-up.
6.) Place your PDA in the USB Cradle.
7.) Stop the MS ActiveSync session on your HOST PC: CTRL-ALT-DELETE > TASK MANAGER > PROCESSES.
8.) Highlight WESCOMM.EXE and select "End Process" button.
9.) Run the file you downloaded from your Vendor in step 3.
10.) The PDA should now begin Flashing the iPAQ's ROM BIOS.
i ignored step 4.)
hope that it helped somebody
Hi!
I was using Newplow's WM6 038 ROM with my N560.
Yesterday I tried to write another ROM(WM6 038 with 8MB pagepool) but during update got an error.. It said it just failed.
Now my N560 is stuck on booting screen(people climbing mountain..)
I tried Warm, Cold, Hard reset but with no luck.
Even the power button doesn't work so I had to remove battery. When I insert battery it powers on by itself.
I can enter bootloader screen by pushing power+record button so I tried to copy rom image file to SD card but it doesn't work.
I tried two ROMs(OS_213U.nbf from Original WM5 ROM and Newplow's) and 3 SD Cards(2GB SD, 1GB MicroSD with Adopter, 16GB SDHC)
Is there any recovery tutorial in bootloader mode?
Help me please!
Sorry for my English.
Have you tried flashing a ROM through the computer rather than the memory card? Try going into bootloader and flashing that way rather than the card.
The pagepool ROM is meant for N560s that have been upgraded to 128Mb RAM... have you upgraded the internal RAM to 128Mb? If you have not, then this may have caused your problem.
I had this problem when flashing to 038 normal RAM (from 035). A hard reset reset to the normal start screen, but nothing worked. However, trying a new burn with the Loox flash tool restarted the process and it worked. I found the cure was to make sure you hard reset the N560 before doing a burn. It appears to be that you have to do this to release enough RAM for the burn program to reside and for "working" storage. You may not have done this.
I suggest you try simply re-running the flashtool with SD/SDHC cards removed, battery in place, on the cradle via your PC, even though it appears stuck. The signals coming from the USB link may wake up the bootloader routine in the N560?
Solved the problem! Thanks for your comments!
I asked same question in Newplow's guestbook and the person who made pagepool rom answered. I used MTTY to revive my pda.
What I did is in below post. need translation
http://4pda.ru/forum/index.php?showtopic=55274
Hi all,
I have the same problem. N560 is stick on the himalaya picture. I tried to falsh from WM5 to new rom for Wm6 and after installation the pda stuked. So I did a warm reset and now only the start picture is apperaing. Problem is that battery is down now.
Can someone give more info on the process followed to revive the PDA ? I just cannont read russian (may be Jinsu77 ?)
Many thanks for support in advance
same problem here please please please someone help us
the only thing i can do is the l c:\os_213u.nbf on mtty program and nothing else happend to the machine
sorry for my english
read, and pay attention here:
[email protected]@p://a.mod-site.net/gb/u/newplow-1.html
POST 203.
It was me asking on Newplow's guestbook.
In case you're using Vista, you need some trick to be able to rom update. Read below.
http://www.modaco.com/content/windo...u-on-vista-it-can-be-done-the-ultimate-guide/
And then you need to download MTTY (I used version 1.42, got it by googling) and follow below steps.
(used google translation from 4pda.ru)
------------------------------------------------------------
For rom update without ActiveSync.
1) take this set of extract, copy it to the folder with the firmware.
2) copy the file os_213u.nbf example in C: \
3) You press the button Recorder + food and poke in the hole reset (Recorder button and hold until you eat dolphins)
4) plug the device to a PC, the Task Manager, shooting process - wcescomm.exe
5) Run mtty, choose Port: USB, connect.
6) If mtty caused an error and shut down, simply restart mtty, if not typed commands, then repeat the procedure with paragraph 3.
7) in mtty command, enter: (first letter in kommande - a little l l от слова from the word L L oad)
> l l c:\os_213u.nbf c: \ os_213u.nbf
Since the end of the process will be an inscription about the error, remove the device from the PC.
9) Run rom update, zhmete "next", until you see dolphins.
10), plug the device to a PC and program.
---------------------------------------------------------------
Hope this helps you all
in advance sorry for my english
I am doing all the instructions carefully and the mtty show this
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,1A0F023Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
the pda shos the dolphins and the full blue bar
after without change anything i run the PocketLOOX5xxFlashTool that i have in the same folder with the :
EnterBootLoader.exe
OS_213U.nbf (originally rom)
RUUServer.dll
RUU.dll
and the only thing i can see is that the PocketLOOX5xxFlashTool is trying to find the pda without any luck
also the pda is stucked in the same screen with the dolphins and the blue bar
do you see any mistake in this procedure
Helppp!!! please
tuluba said:
Helppp!!! please
Click to expand...
Click to collapse
have you closed EVERY process of activesync before proceding with mtty?
I close the wcescomm.exe and the rapimgr.exe is there anything else?
The pocket LOOX 5xx FlashTool cant connect with the N560 and at the and says that Error"The language in this Flash Image update (ENGLISH) differs from that on your device()!" and i have always english rom exept maybe from the last rom "the killer" with the 128MB rom that i dont know if it is an english or something else because the device never opens to see
After flashing in MTTY(don't care about error messages), you need to unplug your n560 from PC. And then proceed romupdate until you see the dolphin picture. Now you plug n560 to PC and cilck next and wait for a while.. Hope it works!
I change the language of the rom and it works
thank very much all of you
At all they have Probs with flash from SD Card: only use a Card with 512MB! I think a Card greater then can't read by the Bootloader....
hey.
i am compeletly new here. I have the same with my n560. I tried to upgrade to 128mb but after restart I see only climbing. I tried everything here but on dolphins afterr line is blue it is finished. that I am unpluging device. starting looxflastool for 560 and first is trying to connect by active sync and that when no connection made I see dolphins on left screen of flash tool window. than I am pluging again and after couple secs I see that: Error"The language in this Flash Image update (ENGLISH) differs from that on your device. I tried to change rom on every language but not working as well. PLEASE HELP
if that helps than i will add than on top when delfins i see on 560 is two lines. first is typed 2.14.G4 on second directly below is 2.15.
and when mtty 1.42 finishing flashing i see following:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0224002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
Need help!!! Please!!!
I bricked my N560. I tried to downgrade from WM6 to WM5 and now I see only delfins and in the first line "2.14.G4" and in the second line "2.15"
What can I do?? How can I flash WM6 or WM5 ROM when there is no connection to the PDA????
ChrisDo said:
Need help!!! Please!!!
I bricked my N560. I tried to downgrade from WM6 to WM5 and now I see only delfins and in the first line "2.14.G4" and in the second line "2.15"
What can I do?? How can I flash WM6 or WM5 ROM when there is no connection to the PDA????
Click to expand...
Click to collapse
You can usually get back to the boot loader if you do a hard reset. I am sure you know how, if not you will find it in the FSC CDROM manual that came with the device. Let us know if this works? I have got stuck at this point too, so I know it works..... hopefully!