Develop Bugs

Gps Recivers & Tom Tom 5

Hiya
Im having a few problems with my bluetooth gps reciver and tom tom 5 Im wondering if you guys can help. Basically I cant get tom tom to see my gps reciver. Even though its connected in the bluetooth connections manager. Ive tried all the com ports in tom tom with no joy anyone had a similar problem and knows how to fix it such as manually setting the coms port perhaps?
this is the gps reciver
http://cgi.ebay.co.uk/NEW-BLUETOOTH...5818774240QQcategoryZ4668QQrdZ1QQcmdZViewItem

Have you looked at my description about how to get it working in the Wiki?

is this the one you are on about
http://forum.xda-developers.com/viewtopic.php?t=28085&highlight=wiki

if it is would it be possible to send me the file or to upload the 5.10 of tom tom upate

That's the thread, yes. And you can find that file on TomTom's website. I forgot to mention that this is meant for WM5, I'm so used to everything being BA WM5 these days, so if your'e running WM2003SE, I don't think it will help much...

Thanks
right i shall have a play later and i'll let you know how it goes

Ive Fixed it
Right tis working, i'll let you know how i did it just incase anyone has the same problem
step by step instructions
1)Switch on bluetooth gps reciver and bluetooth on xda
2)Go in to bluetooth manager
3) Create a new connection, and go in explore a bluetooth device, select the serial port option
4)Then go in bluetooth settings services tab and then go down to serial port connection, check enable service and uncheck authorization required and passkey required
5)Next click on advanced and uncheck the "default device for outgoing serial connections: bt gps, display the device selection screen the next time an outgoing serial connection is attempted.
6) Make a note of the inbound com port (mine was 5)
7) Hit ok
8) Next open up tom tom
9) Go in the change preferences tab
10) Then in to the gps status
11) Then the configure tab
12) Then select other bluetooth Gps
13) Then select which ever bluetooth serial com port was your in bound one (mine was 5) then hit done
14) i suggest you walk outside then your gps works faster it may take a few mins to find you

Ive Fixed it
Right tis working, i'll let you know how i did it just incase anyone has the same problem
step by step instructions
1)Switch on bluetooth gps reciver and bluetooth on xda
2)Go in to bluetooth manager
3) Create a new connection, and go in explore a bluetooth device, select the serial port option
4)Then go in bluetooth settings services tab and then go down to serial port connection, check enable service and uncheck authorization required and passkey required
5)Next click on advanced and uncheck the "default device for outgoing serial connections: bt gps, display the device selection screen the next time an outgoing serial connection is attempted.
6) Make a note of the inbound com port (mine was 5)
7) Hit ok
8) Next open up tom tom
9) Go in the change preferences tab
10) Then in to the gps status
11) Then the configure tab
12) Then select other bluetooth Gps
13) Then select which ever bluetooth serial com port was your in bound one (mine was 5) then hit done
14) i suggest you walk outside then your gps works faster it may take a few mins to find you

BT and Tom tom
Hi
I had the same problems!! but with this thread its now sorted, Thanks
But
When I exit tomtom bluetooth is turned off!
Also I have a HDH-600 headset and both dont appear to work at the same time.
my version is BT-PPC/PE version 1.0.0 build 1900.
any ideas?

Bluetooth switching off when tom tom is closed
erm ive had the same problem mate, im the one who wrote the post above. I havent found a solution yet and ive tried pretty hard for a couple of weeks. So i guess its tough look mate untill tomtom bring out an update or someone codes a fix for it.

I have another BT handsfree called an ADB Speaker, and that works perfectly when using TomTom. That's a BT car handsfree, btw.

GPS Help Please!!

Hi,
Just bought a new Nokia LD-1W GPS and trying to connect via bluetooth.
How do I pair the two devices and how do I create a incoming/outgoing com port to work with tomtom.
I've searched the forum & found nothing:-(
Please can Someone post a step by step process please as it's all confusing.
Anyones help will be gratefully appreciated.
Yohanson

Are you using this with the phone on WM2003SE or WM2005? - then I should be able to assist - Mike

Thanks for replying so fast. I'm using it on WM2003SE.
Thanks

Turn on Bluetooth on the Phone, Turn on the GPS unit.
Go to Bluetooth Manager.
Press Bluetooth symbol on the bottom task bar.
Scroll to the bottom of Bluetooth Connection Wizard.
Select Explore a Bluetooth Device.
after a while you GPS unit should become visable, select it.
On the next page select SPP Slave, then press Next followed by Finish.
On the Bluetooth My Shortcutspage (which sould show automatically at this point) Tap & Hold the GPS icon, from the pop-up select connect. You should get two small green arrows on the GPS icon showing it is connected.
All Done, all you are left with is to configure TomTom, run it up then go to prefferences/ GPS page, select "Other cabled NMEA device" (yes I know its a BT unit but trust me), set the Baud rate (check for this with the supplied info from the manufacturer, or web site, then on the last page go for outgoing Bluetooth comm port 6 (It helps if you put it in landscape mode for this bit as you can see the port numbers this way) - tke it all outside and wait for upto 30 mins for a lock, after this it should be far faster. Sorry for the edit, but didn't add the TomTom bit in first time!!
Mike

If you want any further tips on configuring your TomTom, adding speed cameras, voices etc. try www.pocketgps.co.uk that is set-up for GPS rather than phones (I use both this site for the XDA technical bits) and the other for GPS/ TomTom - Mike

Thanks mike for your thorough step by step guide, but my main problem is making a new bluetooth com port so tomtom can see it in the GPS settings.
Do you know how to access them in bluetooth setting to change outgoing and incoming ports?
I'm lost:-(

At which point following the above set-up does it not offer the selection I have stated to take, I know this works with my BA as deleted the GPS unit and started from scratch just to make sure? - Mike

XDA Exec and Holox BT-321 GPS Receiver

hi there
new to this forum which looks very interesting. Hence asking answer for a problem.
i have bought a Holox BT-321 gps receiver which is blue tooth enabled and i am trying my xda exec to recognise it. aftre turning both devices on xda can see the receiver but puts a yellow question mark before its name.
when turn the gps software on ((Medion Navigator) it does not recognise presence of the gps receiver.
i have great hopes that out there some one does know the answer to this.
to me it appears a software conflict as xda can not install this receiver.
i have tried O2 but they politely refused and asked me to contact gps receiver makers who in turn say the receiver is working fine!!
i was about to pay for a software pathway for sale at ebay but it had been banned by the ebay.
so help please
mohammad asif

Assuming that you did set a port for it (not sure whether it's incoming or outgoing) on the Exec for the GPS unit, you'll probably have to set the port to see the GPS unit on the software also.
That's how I got my GPS unit to work with my software. Please note that the software and the GPS unit that I'm using are not the same as yours. So results might vary.

I too am having exactly the same issues with the Holox 321 and o2 Exec. If anyone has had success pairing a using these two devices and can post a step-by-step walkthrough on how to do it I'd be very grateful.
Thanks.

MDA Pro and BT321
I have got exactly the same problem. It seem that the bluetooth works but the GPS receiver is not recognised. I was thinking of it could be missing drivers or something along those lines

I'm seeing a trend...

hi all,
My m8 has one of them on an XDA2i and the only way we could get it working with TT5 was to set it up as other NMEA GPS on com 6, that did the trick
hope that helps

Thanks BBD, that may help. Trouble is though, I can't even get it to pair correctly. The Exec seems to go through the motions, but the blue light that's meant to flash whenpairing is successful just stays solid.
I also get the question mark appear next to the device in the list of BT devices. What OS is your friend using? WM5 or PPC2003?

hi m8,
he is using WM2003SE, he two has the question mark beside his device I think that just means it does not have a Windows Certificate nothing more, just cheked my TOMTOM device has the question mark too and that works fine
Matt

hi,
just double checked and this is how it worked, pair the GPS receiver up, then go into TomTom and use the NMEA devices with baud rate of 38400 then select bluetooth on com6 and bingo bango your off
cheers
Matt

I think my problem occurs before TT5 is even invloved. From what I've seen WM2005 is very different from PPC2003 as far as BT goes.
I search for a new device and the BT-321 is seen as normal. I select it then enter the sec. key; ok so far. then I'm ask what services I want to use (only "serial port" is available). I select this, then finish. At this point I expect the blue BT light to start flashing telling me I have a successful pairing, but it stays solid. I have tried creating a new outgoing port, but no change.
Until I can get a successful pairing my BT port doesn't appear in the list in TT5, so I can't select it.
I wish I could find someone who has successfully paired these two devices...

Bump.

I can pair my mini s to the bluetooth reciever, but not tt5
i have paired my bluetooth reciever with my xda mini s but when i go to select it in tt5 none of the comports correspond with any i can pair the reciever with. I have installed bttools but this hasnt helped either. someone suggested i needed to build a com port but i dont know where to start, and they also said its because its an xda that theres comport problems, i donubt im the first one with this issue. i pray someone can help me out, would be much appriciated.
email [email protected]

Same problem on my Wizard with the Gpslim 236. However, my fiend brought over his rikaline last night and it worked very quickly. Go figure. I think I'll be exchanging today.

I got the BT321 working with the Universal no problem.
It paired okay, gave me the COM Port option which I took, showed the icon with ? on it.
Going to the COM Ports tab, I created an outgoing port (COM0).
In TT5.21 (I think you need the latest version of TT5) I selected COM0 and after a while it found it no problem..
F.

paring xda exec + gps holux 236
i did pare the 2 after updating tomtom to 5.21 free from tomtom web site then u get com 8 were u can set the outgoing port from the xda ,voila

I have XDA EXEC and have successfully installed the Holux BT-321 Bluetooth GPS. It runs perfectly with a number of GPS applications - so I know the port/Bluetooth configuration is ok. I had to choose an unused com port (0 or 4 work fine). (Ports 1,2,3,6,7,and 9 seem to be already used by the XDA EXEC - so could not be seleted).
BUT (going back to the first post) Medion Navigator (4.2) does NOT recognise the new GPS port. Instead it has options to select ports com1,2,3,6,7,9 but not the "new" port where the GPS is actually configured!
Does anyone have any ideas about this?

After several hours trawling forums and trying lots of things here's what worked for me on an XDA Exec running WM5. In fact I was shocked when it worked! In return for this can someone please think up the next thing after Toothache! The WM5 bluetooth connection thing could also do with a re-write - as could the WM5/XDA Exec instructions/FAQs/help, etc... on BT:
If your aim is to get TomTom working AND you're using a non-TomTom BT GPS, try this (the TomTom GPS seems to install itself without much problem):
1. Pair the GPS with your device BEFORE installing TomTom, because the GPS port needs to be already setup on your device for TomTom to recognise when installed.
2. Then install TomTom
3. Launch the BT connection thing in WM5. Make sure the BT is discoverable (first tab). Select 'Security' tab and ensure 'Authentication (Passkey) required is checked.
4. Go to 'Devices' tab and select 'new partnership...' The pairing thing should find your GPS and will then ask for the passkey - select next WITHOUT entering anything even if there's a passkey. If you enter the passkey now you will not get step 5 which is a crucial milestone.
5. The device should now ask if you want to add the GPS to your list, select yes
6. The name of the GPS is shown. Ensure 'serial' port is checked and hit next
7. You will be asked for the passkey again - enter it this time
8. At this point the GPS may look like it's not paired. The lights may flash as if unpaired. You'll also get a question mark icon next to the GPS in your list. Not to worry.
9. Select 'com ports' tab and select 'new outgoing port'. You should see your GPS listed. Select it and hit next. From the list of ports select COM8. Make sure the 'Secure connection' is UNCHECKED - otherwise you'll be pairing everytime you start TomTom! Select Finish. You should see your GPS (COM8) listed in 'COM ports' tab.
10. Turn off 'device is discoverable' (first tab).
11. Now install TomTom. Having installed the GPS as above, TomTom will now know about COM8 i.e. where your GPS is to be found. If you hadn't done that first there would be no COM8 and no GPS connected to it as far as TomTom is concerned.
12. Turn on the GPS
13. Launch TomTom and go to 'preferences/ GPS Settings'. Select 'configure'. Select 'Other bluetooth GPS'
14. You should get a list of ports and with any luck you should see 'COM8' - select it and hit 'done'.
15. I think at this point the GPS page in TomTom came alive, or maybe I had to restart TomTom - can't remember. And it works thus far!
Toothache - what a palaver!

BT/GPS Problems
Hi,
I have a program that can sort out the com port problems between the bluetooth and gps software.
I have included the program as an attachment, just unzip it into your PC, make sure you reboot your PDA, sync your PDA to the PC and run setup.
Problems solved.
Cheers,
John

bigbird49 said:
Hi,
I have a program that can sort out the com port problems between the bluetooth and gps software.
I have included the program as an attachment, just unzip it into your PC, make sure you reboot your PDA, sync your PDA to the PC and run setup.
Problems solved.
Cheers,
John
Click to expand...
Click to collapse
Hi,
I`m a new member.After installing your litle tool i can`t start this application and also can`t find it under programs or anywhere else?
I`m using a T-Mobile MDA Compact II with WM5 latest ROM, a Holux BT321 and TomTom6. `have expierences with BT and XDA`s using TT5 for a long time.
After upgrading to new devices and new sw i have the following problems:
I can connect the BT321 as a BT Mouse and get a good signal.Using TomTom6 the navigation works with a delay of round about 100 meter. I`m looking for a resolution to connect the BT321 via the NMEA Interface.
regards
AK
____________________________
MDAc II
WM5
BT321
TT6

Britishbulldog said:
hi all,
My m8 has one of them on an XDA2i and the only way we could get it working with TT5 was to set it up as other NMEA GPS on com 6, that did the trick
hope that helps
Click to expand...
Click to collapse
I have tried your advice and it works a treat, thanks to you and everybody else who contribute to this forum

com ports and Bluetooth GPS settings

can some one here please help me this is driving me mad for days now i have been looking thro the forums at some of the posts how to set up tomtom 5 and how to setup the gps bluetooth receiver i have followed all instructions how to but iam not getting any where tomtom is installed Ok the gps control panel is installed but i cant seem to get any blue tooth com ports to show up in tomtom apart from
qct data interface
RIL on com6
com7
serial cable on com1
Ir on com3
if i rember when i had it installed on my xda2i when i went to tomtom and
bluetooth other then com ports i could pick from tow bluetooth coms 5 & 6
this really is getting to me now i do believe it possible to do it there guys selling the info on ebay with pictures of it running on the XDA exec but i just cant seem to do it
please i would be so greatfull for any help i only got the phone last week i like it

TomTom & Bluetooth GPS
Hi there,
I am just guessing but give it a try, as i am using a cradle based GPS device bcs i wanna use the bluetooth headset as well during drive.
1. Try to first pair your Bluetooth GPS device with ur phone.
2. Once pairing is done, start TomTom
3. Goto ""ChangePreference->ShowGPS Status->Configure->Other Bluetooth GPS.
(Com1 is for the wired NMEA GPS device)
Your phone must within the connection of ur Bluetooth GPS device, now try BLUETOOTH SERIAL PORT Com5.
Try if its help
Sidd

Re: TomTom & Bluetooth GPS
sidd said:
Hi there,
I am just guessing but give it a try, as i am using a cradle based GPS device bcs i wanna use the bluetooth headset as well during drive.
1. Try to first pair your Bluetooth GPS device with ur phone.
2. Once pairing is done, start TomTom
3. Goto ""ChangePreference->ShowGPS Status->Configure->Other Bluetooth GPS.
(Com1 is for the wired NMEA GPS device)
Your phone must within the connection of ur Bluetooth GPS device, now try BLUETOOTH SERIAL PORT Com5.
Try if its help
Sidd
Click to expand...
Click to collapse
Hi Sidd,
I have tried that. The problem is that the phone won't allow me to connect to any other port than 8, 4 and 0 and in the Tom Tom menu there is no option of chosing those ports.
Thanks for advice anyway.
Rob

Hi Rob,
Make sure ur Beam is OFF
Start->Settings->Connection->Beam
MUST be UN-TICKED.
(By the way I am in London, where r u?)

One more idea :idea:
1. Pair ur GPS
2. Once pairing is done, switch OFF ur phone's bluetooth (bcs ur phone is engaging the com ports), do not switch OFF ur GPS.
3. Now soft reset ur phone, make sure the Bluetooth is still ON
4. Start TomTom, see if there are more ports now. Try 5 or 6
GoodLuck
Sidd

Hi Sidd,
Thanks for another piece of advice but unfortunately that did not help either My Beam is OFF and I've tried the way with soft reset but that did not work either. I am getting desperate here
My device is XDA Exec and I am using (or at least trying to use) a BT GPS receiver with it. After pairing devices everything seems to be all right except the fact that I am not able to assign any other ports than 0, 4 and 8 to be used with GPS receiver. As I mentioned earlier there is no option of choosing any of these ports in TomTom5 software with the only options as follows:
qct data interface
RIL on com6
com7
serial cable on com1
Ir on com3
Maybe you know any ComPort Manager software I could use to assign the Bluetooth connection to a specific port?
As far as my location is concerned I am in Hayes - that's Zone5 near Heathrow airport.
Cheers,
Rob

Which TomTom u using, is it the legal version or ****. Do u wanna meet, so we can try my version?
I am in Pinner, do u drive?
Sidd

Hi all,
I have exactaly the same message and problem.
Natan69
Please if you found a solution help me. i installed my tom tom today so I expect that you may solved your problem by now.
please help me you have been in this situation and you know what i am through.
Thanks

Hi all,
I had exactly the same problem than you guys...
But first of all I couldn't even install tomtom5.
The version 5.0 crashed in every attempt to install and version 5.21, simply crashed when choosing the map.
Well, I'll try to put every step I did to get it working.
First of all, had the BT GPS paired with K-JAM and set new outgoing port COM6 to it. (in my case I only had COM6 or COM7).
1 - With the full copy of 5.0 version on HDD, replaced setup.exe with the one from the 5.21 update (this allowed the setup for 5.0 to run, and is the one that has the gps.cab file);
2 - Updated with version 5.21;
3 - Copied the map to \Storage Card\
4 - In Windows created the file CurrentMap.dat using Notepad containing: & \Storage Card\XXXX-Map\ (where XXXX is the map name. the final \ is mandatory);
5 - Copied the voiceXX.cab to device and run it;
At this point I was having the same problem (both COM6 nor COM7 appears in tomtom)
6 - Downloaded the GPSInfo_WM5.zip attached here and installed it;
7 - Executed this program, configured it to COM6 (port I had configured BT GPS to work with) selected the correct baud rate (very important, it's on the user's manual of the BT GPS) and click Start GPS to check it's response to the program;
8 - Click Close GPS so that the COM port was not in use;
9 - Started tomtom, edit the settings and chose Other Bluetooth GPS.
Now the ports COM6 and COM7 was there!!!!
10 - Chose COM6 and in 10 seconds tomtom was trying to aquire satelites.
I hope this helps you all. I spent weeks trying to make tomtom work and I got it working yesterday.
BTW, excellent forum. If it wasn't this forum (and another one only in portuguese I was still mad with this thing.
Good luck in your adventures.
Cheers,
Nuno.

I installed the gpsinf but it did not solve anything
Thanx for the help

Pairing a GPS with XDA Exec to get TomTom working
After several hours trawling forums and trying lots of things here's what worked for me on an XDA Exec running WM5. In fact I was shocked when it worked! In return for this can someone please think up the next thing after Toothache! The WM5 bluetooth connection thing could also do with a re-write - as could the WM5/XDA Exec instructions/FAQs/help, etc... on BT:
If your aim is to get TomTom working AND you're using a non-TomTom BT GPS, try this (the TomTom GPS seems to install itself without much problem):
1. Pair the GPS with your device BEFORE installing TomTom, because the GPS port needs to be already setup on your device for TomTom to recognise when installed.
2. Then install TomTom
3. Launch the BT connection thing in WM5. Make sure the BT is discoverable (first tab). Select 'Security' tab and ensure 'Authentication (Passkey) required is checked.
4. Go to 'Devices' tab and select 'new partnership...' The pairing thing should find your GPS and will then ask for the passkey - select next WITHOUT entering anything even if there's a passkey. If you enter the passkey now you will not get step 5 which is a crucial milestone.
5. The device should now ask if you want to add the GPS to your list, select yes
6. The name of the GPS is shown. Ensure 'serial' port is checked and hit next
7. You will be asked for the passkey again - enter it this time
8. At this point the GPS may look like it's not paired. The lights may flash as if unpaired. You'll also get a question mark icon next to the GPS in your list. Not to worry.
9. Select 'com ports' tab and select 'new outgoing port'. You should see your GPS listed. Select it and hit next. From the list of ports select COM8. Make sure the 'Secure connection' is UNCHECKED - otherwise you'll be pairing everytime you start TomTom! Select Finish. You should see your GPS (COM8) listed in 'COM ports' tab.
10. Turn off 'device is discoverable' (first tab).
11. Now install TomTom. Having installed the GPS as above, TomTom will now know about COM8 i.e. where your GPS is to be found. If you hadn't done that first there would be no COM8 and no GPS connected to it as far as TomTom is concerned.
12. Turn on the GPS
13. Launch TomTom and go to 'preferences/ GPS Settings'. Select 'configure'. Select 'Other bluetooth GPS'
14. You should get a list of ports and with any luck you should see 'COM8' - select it and hit 'done'.
15. I think at this point the GPS page in TomTom came alive, or maybe I had to restart TomTom - can't remember. And it works thus far!
Toothache - what a palaver!

Newb question- GPS

Hello all,
As you can see by my post count I am a newb so please cut me some slack
With that said, I bought a Holux GPSlim 236 bluetooth GPS reciever and I am having trouble getting it to work with google maps..I just want to have some type of gps working on my phone no matter what program it is..Can someone please shed some light onto how I can get it set up with my phone or what is the best program to use with this phone?? Any help is greatly appriciated..

Try this http://forum.xda-developers.com/showthread.php?t=293397
after pairing your GPS device and setting up a comm port for it as follows:
Start/Settings/Connections/Bluetooth.
Make sure Bluetooth is set to "On".
Menu/Devices
Menu/New
Select your GPS device from the list and press Next.
Enter the passkey for the Bluetooth GPS. For example, 12345678.
Next
You should get a message box saying "Your Smartphone has connected".
OK
Next
Check the "Serial port" checkbox.
Done
Done
Menu/COM Ports
Select your GPS.
Menu/New Outgoing Port.
Select your device and press Select.
You will see a COM port that has been chosen for your GPS. For example, COM6.
Done
Done
Done
Now your GPS is set up on COM6.

I have the exact same setup. What finally worked for me was the com port config app found in this thread (http://forum.xda-developers.com/showthread.php?t=293397&highlight=google+maps). Google maps works great with gps, providing you have a phone signal. Have fun.