Related
AT&T(aka deathstart) will be releasing their latest WM6 in a few weeks(I am suspecting but don't know anything for sure). My problem is that I have loaded Hard SPL v7 -> OliPro 2.10. I am wanting to remove my custom ROM and install "the" factory ROM. But I can't do this with Oli installed.
So how to remove so I can return my phone back to the factory ROM. I am wanting to sell before it loses the rest of its value as well.
Found numerous links to install but can't find anything to uninstall.
Any info/advice will be much appreciated.
--Mickey
Down Grading WM6 to WM5
This topic is "well covered" in Mr. Vanx's guide....... do a google search on "mr vanx" go the the site & look around...... I've done it successfully a number of times...... downgrading SPL7 is "one of the steps"......
Good Luck,
vpu2....OUT!!!!!
This was the site that I used to walk me through the install. Unfortunately I have been all through this site and haven't been able to find "downgrading" documentation. Didn't see a search button. Lots of good info though.
--Mickey
Downgrade SPL guide
Downgrade guide
cmalberto said:
AT&T(aka deathstart) will be releasing their latest WM6 in a few weeks(I am suspecting but don't know anything for sure). My problem is that I have loaded Hard SPL v7 -> OliPro 2.10. I am wanting to remove my custom ROM and install "the" factory ROM. But I can't do this with Oli installed.
So how to remove so I can return my phone back to the factory ROM. I am wanting to sell before it loses the rest of its value as well.
Found numerous links to install but can't find anything to uninstall.
Any info/advice will be much appreciated.
--Mickey
Click to expand...
Click to collapse
Are you sure that original retail ROM cannot be flashed if you have OliPro 2.10? Before you flashed custom ROM on your "virgin" device, you had to install Olipro 2.10, right? Then you flashed the custom ROM. So the reverse procedure should work as well. Correct me if I'm wrong.
juzzie said:
Are you sure that original retail ROM cannot be flashed if you have OliPro 2.10? Before you flashed custom ROM on your "virgin" device, you had to install Olipro 2.10, right? Then you flashed the custom ROM. So the reverse procedure should work as well. Correct me if I'm wrong.
Click to expand...
Click to collapse
I think this was the right question to ask. I have not had RUU install problems before..but just to make sure, I tried to run RUU_Hermes_CINGULAR_WWE_3_1_.57.502.1_6275_1.48.00.00_108-ATT-MR3_Ship to put my phone back to the "current" Cingy version(prep for WM6 by Cingy). So when I ran the RUU ran and I got to the point where the software was attempting to check out the info on the PDA. I got the 206 connection error. I tried to follow the troubleshooting of the readme.doc. It basically said to check your connections, reboot your computer, PDA, etc...I know the USB connection works as it connects to my Vista WMDC just fine.
So, just now as a last resort, I booted to the Bootloader screen and reconnected. Vista recognized and loaded a "new" driver(why I don't know). I ran the RUU and guess what??...ROM is now loading. All appears well and no need to downgrade the SPL.
This is probably a documented feature of RUUing w/in Vista somewhere. If not, then perhaps it can be added to some Upgrading Wiki.
Thanks for everything.
--Mickey
So I wouldn't have to break down the exe into the nbh files and do it all separately like in Mr.Vanx's guide? That would be awesome if I could just flash the original exe file, and then just downgrade the IPL.
Iv'e flashed the ATT ROM on the HardSPL with zero issues. Dozens of times.
Hello, just to start I will say that I'm completely new to PDAs, because I got my HTC TyTN a few days ago. So I had WM5 and I installed WM6 from http://forum.xda-developers.com/showthread.php?t=320829
But then I saw the Schap's WM6 Pro 4.20 Roms, which had TouchFLO installed and tried to install the full version, when it asked for Bootloader version I ticked the SP 2.02/2.10 (or whatever it was), because it was the closest to my Bootloader version - 2.03 (if I'm not mistaken). It started installing but after few seconds it displayed me some error. I don't remember what was the error, I only remember that it said that something was corrupted. So I would really appreciate any help installing Schap's WM6.
P.S As I said i'm newbie with PDAs, so please if you try to expain what should I do make it a bit more .... simple .
I'd suggest using the detect spl option when you try flashing. If you still get an error I would highly recommend posting the details so you can get the correct help.
There are several ways to get in touch with a new rom.
Please read the wiki, there should be everything explained.
Hermes Wiki
If nothing works there is only one solution for me, yet.
Then I have to change manually to bootloader mode and flash the original latest provider rom. After this step I am able to flash a rom of my choice again. regards
"Error, Unknown version! You should pick safe SSPL" is the error that i get when I try the Autodetect. Should I try using safe SSPL or ... ?
I also forgot to mention that I'm using Windows Vista. I heard that there were some problems updating ROMs using the Windows Mobile Device Center, so perhaps this is the problem ?
To start with I strongly recomend you read the WIKI.
As first base you should install HARD SPL (again read the WIKI).
After you'll have hard spl on yor TyTN you should use autodetect.
(Make sure you are fully connected in Windows Mobile Device Center befor any of the above)
I've installed HardSPL guided by http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
but I still get the same error. I also changed the WMDC drivers with those from AS again beign guided from the above link. Should I tick the SPL-2.02/2.10/2.30 New Bootloader or what should I do ?
Flash using an SD card.
YES pick Safe SSPL, it will run through and be fine. Sometimes that happens.
Flash a stock WM5 ROM. Get into windows. Download HARD-SPL (2.10). Use the force SPPL option while activesynced (GUEST) to flash the BOOTLOADER. Get back into windows, and use the same procedure for the OS ROM. Use force SSPL while activecyned..
So I already upgraded to WM6 on my 8525 a while ago (I don't remember at all how I did it or which firmware I used). I want to use the 5.0.2 diamond.. is there anything special I need to do to downgrade first? I'm a little lost... and the links for the first sticky are a no go... anyone have any easy info so I don't have to get forever lost wading through endless posts :|
Download the ZIP file, extract it, and run the EXE in the extracted location. Why do you think you need to downgrade first?
Too used to hacking my psp I guess lol
So I have a Ruu_signed.nbh and a RUUWrapper.exe which gives me an application error when attempting to run in xp. Do I need to throw these on an SD card (I don't have one), the files are too big to fit directly on the device.
I feel as if I'm missing something blatantly simple
You probably don't have the .NET Framework installed. I believe version 2.0 is required.
Ahh, thank you.
I think one last questions, I hit auto detect for my version of SPL. it says "this is 1.11 retail, you are recommended to use SSPL, would you like to?" I hit yes, then I hit next, then it says "please be aware that this flasher is intended solely for SPL 1.11 and you must have 1.11 Hard SPL installed in order to flash any unsigned files"
was there a pop-up I missed for the install of the 1.11 SPL? Or am I having difficulty reading this correctly
Ooh, I guess you don't have HardSPL installed. It's highly recommended that you flash it before flashing anything else. See http://forum.xda-developers.com/showthread.php?t=296722 for more info on that and, after flashing HardSPL, you should be OK flashing OS ROMs.
Ahhh... well thank you much, I have everything up and running now *relaxes*. I appreciate the speedy responses
No prob And I would ask that you comment in the MaRaHoX Diamond thread regarding how well the ROM works for you, after using it for a bit.
will do, especially after I find and install a cab for windows live on it (need messenger)
Hello to anyone who can help me...
i am posting this thread after searching this forum for answers to my problem, and i could not find the answers...
I have the Diamond (DIAM100) with Original SPL 1.37.000 and GER Stock Rom installed.
My Upgrade goal is HardSPL 1.38 Signed (Olinex) / DiamondProject V2 GER / radio .05
I try to upgrade SPL, Radio and Rom according to several guides in this forum, but nothing seems to work for me.
I tried using the RUU Program with HardSPL, tried Diamond CustomRUU, tried manual Bootloader access, everytime the Upgrade Software stays at 0% (on the phone also) and after about 5 minutes i get ERROR [262].
Luckily, i haven't bricked my diamond yet, it always came back to life again.
i can confirm, that the device enters bootloader mode, then changes to grey screen with progress bar. But that is all.
Maybe it is a Vista issue, maybe not.
But all i get is ERROR [262]: Update Error
Suggestions, anyone?
Thanks in advance for any serious help...
______________________________________
HTC TD DIAM100
MDA Compact I (Magician, unmodified)
MDA VarioII (Hermes, running Schaps 3.54GER, thanks Schaps great ROM)
I get EXACTLY the same... i've tried everything (except a hammer) to fix it.
I'm running
Rom: 1.37.707.1 wwe
Radio: 1.00.25.03
Proto: 52.26a.25.09h
I'm also using Vista 32
(all fresh out of the HTC box)
http://forum.xda-developers.com/showthread.php?p=2338991
Are you running Vista X64 coz i had the same error in it ..
try to flash it with xp!
udayrulz said:
Are you running Vista X64 coz i had the same error in it ..
Click to expand...
Click to collapse
... Running Vista Ultimate 32bit, but not sure if that will make a difference...
I will try to get hands on XP computer tonite....
You can always try running the RUU update utility in WinXP32 compat mode.
What Hard SPL ar eyou using???.... usually the problem...
you will need Developer edition if the ROM is not signed.
developer edition worked for me on Vista 32. Thanks guys!
OK
I ran a Hard-SPL (from the dev thread) Diamond-OliNex
This completed and did whatever it did and i had to do the basic setup on the phone again.
I have now got the radio ending .06 from this thread this thread and cant get it to work with the OilNex Hard SPL or the 1.34 listed in that thread.
I'm back to square one where Error 262 Update error is occuring.
I'm tring to flash the radio as the O/S i have appears to be running sweet but its having web issues that appear to be DNS/Connection related.
This needs an idiots guide like the other phones have .... 'coz i'm an idiot and I can't do it.
Monty Burns said:
OK
I ran a Hard-SPL (from the dev thread) Diamond-OliNex
This completed and did whatever it did and i had to do the basic setup on the phone again.
I have now got the radio ending .06 from this thread this thread and cant get it to work with the OilNex Hard SPL or the 1.34 listed in that thread.
I'm back to square one where Error 262 Update error is occuring.
I'm tring to flash the radio as the O/S i have appears to be running sweet but its having web issues that appear to be DNS/Connection related.
This needs an idiots guide like the other phones have .... 'coz i'm an idiot and I can't do it.
Click to expand...
Click to collapse
Yeah, but for me the problem still is to get ANY HardSPL on the Diamond in the first place.
I was trying to put HardSPL 1.38_Signed to the phone...
Adwinp: thanks for the advice, but did not work either...
As far as i can tell, this may be a problem with the USB driver from the Windows mobility center software...
I will try on real XP and give you feedback tomorrow.
thanks guys.
Doctor_Who said:
...
I was trying to put HardSPL 1.38_Signed to the phone...
...
Click to expand...
Click to collapse
The developer edition i.e. unsigned worked for me.
I am currently going through the stages in the wiki VERY closely. Dont know if they will work :/
Doctor_Who said:
Hello to anyone who can help me...
i am posting this thread after searching this forum for answers to my problem, and i could not find the answers...
I have the Diamond (DIAM100) with Original SPL 1.37.000 and GER Stock Rom installed.
My Upgrade goal is HardSPL 1.38 Signed (Olinex) / DiamondProject V2 GER / radio .05
I try to upgrade SPL, Radio and Rom according to several guides in this forum, but nothing seems to work for me.
I tried using the RUU Program with HardSPL, tried Diamond CustomRUU, tried manual Bootloader access, everytime the Upgrade Software stays at 0% (on the phone also) and after about 5 minutes i get ERROR [262].
Luckily, i haven't bricked my diamond yet, it always came back to life again.
i can confirm, that the device enters bootloader mode, then changes to grey screen with progress bar. But that is all.
Maybe it is a Vista issue, maybe not.
But all i get is ERROR [262]: Update Error
Suggestions, anyone?
Thanks in advance for any serious help...
______________________________________
HTC TD DIAM100
MDA Compact I (Magician, unmodified)
MDA VarioII (Hermes, running Schaps 3.54GER, thanks Schaps great ROM)
Click to expand...
Click to collapse
I had the exact same problems. I tried every possible combination of Hard SPL and ROMs. Here is what worked for me in the end (no problems since):
1. install newest .Net 3.5 on windows PC (don't know if this has anything to do with my problems but after installing everything started working fine)
2. install Unsigned HardSPL (developer edition): http://forum.xda-developers.com/showthread.php?t=400950
3. install chosen ROM / Radio ROM with RUU (Rom Updater Utility): http://forum.xda-developers.com/showthread.php?t=396073
After flashing a ROM the device makes a hard reset so you should backup your data first! http://forum.xda-developers.com/showthread.php?t=299705
good luck!
Finally it worked, also thanks to all who replied in this thread.
So i like to share my experience in this:
1. first i downloaded all SPL and Radio i could find, then i looked for GER language Rom. Quickly decided for DPT V2.
2. First attempt to flash failed completely on a Vista PC (32 Bit Ultimate)
3. Back home, moved all the downloaded files to my XP SP2 PC..
4. Noticed: DiamondCustomRUU would not start in XP, got error message saying "... could not be initialized", so i tried the standard RUU instead, with the shortcut of manually putting the PDA into Bootloader mode...
5. Sucessfully flashed HardSPL 1.38 on the Diamond, and the device rebooted with Hard reset.
6. Next i tried to upgrade Radio to .05 Version... Failed, stuck a 0%
7. Changed SPL to 1.40 (Unsigned), now the Radio could be flashed. Seems that Radio Files are Unsigned?
8. Flashed DPT V2. Success.
But still wondered about the unsigned Radio file...
Again, thank you all
-------------
So as you can figure out from the thread title I have a problem flashing my htc diamond.
I have installed a HardSPL version 1.30 OliNex, I can confirm that becouse on the three color screen there is a text saying "1.30 OliNex".
I still have the original ROM that comes with the phone when I bought it, so this meant to be my first flashing.
I want to flash the phone with this rom http://forum.xda-developers.com/showthread.php?t=593678 it is a WM 6.5 based ROM.
Because in the ROM package there wasn't a ROMUpdateUtility.exe I used it from other ROM package.
Connected via ActiveSync and followed the wizard. The phone reset and there came a gray screen with a progress bar. Now both progress bars on the phone and on the PC screen remain 0% and after a wile RUU finished with 262 ERROR Connection error, see the attached picture.
After that I tried to flash it from Internal Storage. A followed the steps according the procedure, and after the three colored screen it came the gray screen with "Loading..." message. I waited for almost 30 minutes and nothing happened.
What seems to be the problem?
I assumed about firewall disabling the connection. But I turned off the firewall and again the same story.
Then somewhere I found that there is incompatibility with the RUU and HardSPL version, but tried to flash with the same RUU that I used when I was installing HardSPL.
Then I tough that the problem is about flashing unsigned ROM on a signed HSPL, but it is not that the ROM is signed.
I am afraid to use MTTY so I don't brick my phone, because this is my first time flashing a Diamond.
I'm confused What seems to be the problem?
Any help can be welcomed.
Could this be indication of a hardware problem? When waiting for the "Loading..." message disappear the back cover warms a little.
Thanks.
1. Did you use the RUU from my thread?
2. NEVER USE AN H-SPL RUU TO FLASH ANYTHING OTHER THAN H-SPL!
3. is this a CMDA phone. IE, what network are you on?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
EDIT: I did tried the RUU you recommended in your thread but it's the same.
I think it is in the PDA.
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Hmmm..
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
johnyboy_ said:
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Click to expand...
Click to collapse
The connection between PC and PDA is made, because as I said there is a progress bar on the phone screen too.
djfuego said:
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
Click to expand...
Click to collapse
As I understand you, you are saying to install later version of Hard SPL right?
So to install a new version of Hard SPL I just need to do the same procedure as the first time, or I have to uninstall the previous one?
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
djandreski said:
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
Click to expand...
Click to collapse
Presuming from your post, you are using a signed Olinex SPL, i doubt that the rom has been signed be OliNex, the only difference with Dev is you can flash any Rom, flash the Dev one from my thread, nothing to be afraid of
Good Luck
Badwolve1
What are the steps of installing new SPL?
Do I just need to do the same procedure as the first time, or I have to uninstall the previous one(somehow)?
UPDATE: I did it, I successfully flashed my Diamond PDA! It seams that the problem was in the SPL I installed 1.40 OliNex Unsigned and it flashed like a charm. Thanks guys for the help. Now this thread can be closed, or do I have to close it myself.
Great!
Glad it all worked out