Develop Bugs

I've tried upgrading my JasJar with Xda_Exec_Upgrade_v1.30

I guys, I've tried upgrading my JasJar with Xda_Exec_Upgrade_v1.30.162, using MaUpgradeUt_noID and when update was complete I cannot load my JasJar anymore. I am using hard reset, but when choosing "0" off the boot screen - noting happens and screeen remains black.
Can someone please help me with this issue?
Thanks a lot in advance,
Best regards,
Stazik

Try reflashing it again. If it does not work, try reflashing back to the i-Mate ROM.

Whats the version of your bootloader (the screen with serial at the top changing to usb when plugged into usb)? If it is 0.56 or something else below 0.6 thats an already known problem.

I had similar problems with my O2 upgrade.
Try:
- Turn off USB in ActiveSync
- Hold Power/Light and press reset button
- Run the upgrade again

Thank you very much for help and support, guys!
When I try flashing my JasJar with Bootloader update or JASJAR_WWE_13076_164_10900_wwe_ship I get the same error message: Error 101 Connection Error. And also when I disable ActiveSync USB and plug my Jasjar into USB - I get a message from windows saying the device was not recognized...
The only I can get from JasJar is a black screen, except when I press two soft buttons and reset - that gives me a screen with 0 and x to choose. Neither of choices helps thou.
Any help is appreciated. Thanks a lot.

you didnt answer the question re the boot loader number.
when your screen is grey or starting to reset, there are numbers on the screen. what are they.
if it is less that 0.6 your in trouble and assistance is different to if your boot loader is 1.0 or similar.

My screen doesn't change from gray except when I do hard reset. And then I hit two buttons and reset, then press 0 the message Clearing now appears and then everything returns to gray again.
How can I tell the version of bootloader in this case?
Thank you in advance!

they are hard to see, if the screen is grey, the numbers are black.
f the screen is blue/coloured, the nmbers are probably red.

Thanks for help guys,
I brought my JasJar for service today, somehow they were able to put older ROM in there. Now I've upgraded bootloader, hopefully newest ROM from i-mate going to fit without problems )

Well I've killed my Jasjar upgrading I was installing the bootloader update. It sat there saying "Checking information on your device" for about 30 minutes after the update started (notes said it would take 10 so I figured something was amiss - disconnected & rebooted my PC.
Now when I turn the Jasjar on I get the USB/Serial screen referred to above and (good news I figure) it has v1.00 at the bottom. How do I fix this?
TIA

Sheesh. I did a search (I know I should have done that first) and found the answer here
Took a while to find a copy of mtty to download, but found that at http://buzzdev.net
Once I'd done the Set 14 0 and tried the boot loader update again it took seconds so something definitely went wrong the first time.

For All Those Who Stuck In The Boot Screen - Try Mamaich Method !!!

Before 1 month my UNIVERSAL stuck on boot screen and like every one I'll start to test everything - including TASK 28 command to return him back but without succsess. Before 2 days some one put a thread about formating DOC and I remembered that I was try to format my DOC and after few weeks my Universal was stuck so MAMAICH wrote this:
mamaich said:
if you can enter bootloader - use "task 28 55aa", this would restore DOC to its original layout.
If you cannot - contact service center.
Click to expand...
Click to collapse
After this .... gues what .... EVERYTHIG run back to normal again
I will repeat myself:
MAMAICH
IF SOME ONE SAY THAT YOU'RE NOT A GOD - HI LIES !!!
AFTER THIS EVERYTHING IS RUNING OK ON MY OLD UNIVERSAL!!!
Thank you very very very MUCH !!!
Thank you again !!!
Hope this work to most of you

Oh My God !!!!! My Jasjar Recovered !!!!!!!
Thanks Alot !!!!!!!!!!!!!!!!!!!!!!!!!!!!!

where is this task28 55aa? cus im in the bootloader screen but i cant get anything else to work

Step by Step :
get the tools at attachment , as mamaich told, you have to use it in bootloader mode , (Power + Light Bulb + Reset)
1. Stop Activesync USB connection
2. Uni : Reboot Bootloader then Connect USB
3. PC : Run mtty1.42.exe
4. Choose USB in "Port" (Reconnect if can't find/reconglize USB and try remove sim and sd card)
5. type : task 28 55aa
6. Press Enter
7. Cause DOC reformatted, so there's no rom in DOC ,try reflash any rom that you like .
For task 28 55aa in mtty success , will show the message (attachment )
DONE .

i can only choose from COM1, COM2, and COM3, it doesnt find usb, and ive try reconnecting in

i find you must kill the wcescomm, wcesmgr and rapimgr exe's using task manager before you get the 'usb' option in mtty (kills activesync)

rite got a window come up in the progam
typed "task 28 55aa"
next line came as "USB>"
so is that it done? cus i aint seen anything else happen?

afaik, thats it
now reset back into the bootloader again and load a (whole, inc radio) ROM

stupid question here, but the update i installed earlier effed it up, so where can i get one that def works, and how do i install it on lol, im think

If you want to make sure it works i suggest getting the latest rom from your carrier (orange? - http://www1.orange.co.uk/business/download/m5000/M5000ruu.exe)
then you can upgrade (if you want to) to other, perhaps custom roms and a later radio ROM.

i got o2 rom im trying to install but it says it can only do it thru activesync, but that wont find my xda, any ideas how to bypass that?

thats because you killed activesync in the last process, start it again (from the start menu) and the upgrade should work

restarted my laptop and still activesync wont reckonise my xda, any other ideas? (its still boot loader mode, if i do a normal reset the screen just loads red and scrambled)

start the update process while in bootloader mode, you don't need activesync at all.

yeh i got the rom to install on it, went to soft restart it like it said, press 0 to conitinue, and wat a suprise a red, green and blue scrambled fuzzy screen, any ideas where to go now?

have you installed the rom yet? if not you need to reset it into bootloader mode (http://wiki.xda-developers.com/index.php?pagename=Universal_Resets) and then start the rom upgrade.

yeh i reset it in bootloader mode, and i installed the new rom from the o2 website, but it didnt work, so i need a rom that either puts it back to original 02 settings or rom that at least allows me to get a workin screen up again

what was wrong with the o2 one you had?

i went to sell my phone, so i wanted to clear the data permanently, but i thought id put an update on it to add to its features aswell, but the update effed it up big style, and now i cant sell a broken phone

someone add to wiki.

Bricked hx2110 help

I did a rom upgrade on an hx2110 - installed successfully, but now the only thing I can get the pda to do is go into Pre bootloader mode (i.e. Pre-BL 1.00.02 blue screen). SO I tried the universal bootloader method - makes it all the way to the flashing portion but then does NOTHING - the terminal simply sits there saying "ready" and does not upload anything - the program sees the correct communication port (ie. usb01 or whatever). HOW do I force an upload???
Thanks!
Rusty

On another note - I had purchased a working 2110 with a good mobo to replace this one if the flash is not repairable - is that a difficult procedure? Unfortunately, the 2110 I purchased was not working, but this may still be in the books at a later time, so some info would help.
Thanks!

Rustmonkey said:
I did a rom upgrade on an hx2110 - installed successfully, but now the only thing I can get the pda to do is go into Pre bootloader mode (i.e. Pre-BL 1.00.02 blue screen). SO I tried the universal bootloader method - makes it all the way to the flashing portion but then does NOTHING - the terminal simply sits there saying "ready" and does not upload anything - the program sees the correct communication port (ie. usb01 or whatever). HOW do I force an upload???
Thanks!
Rusty
Click to expand...
Click to collapse
Rusty,
You are so lucky that I experienced this problem and solved it on my own. You did not specify what ROM you were loading, but here is the fix:
First you need to get another pocketpc, hx2000 series like yours that is working.
Put that device into white screen bootloader or pre-BL mode (depending on which device you got to borrow)
Ensure that the battery on that device is 100% charged.
Run the original ROM upgrade for the ROM you wish to install (use PDAViet if it's WM6 and use the HP SP32408 to Run it)
Hit all the Ok screens until it brings you to the one that has the "UPDATE" button.
Remove the working Ipaq from the cradle and place it's 100% battery in you own.
Put your Ipaq into pre-BL mode and put it on the cradle. Press the calendar button to activate the usb drivers.
Once it says "USB", Hit the "UPDATE" button and it will load the proper ROM to your IPaq.
When It is done, perform a hard reset by formatting the PS on the device.
Voila!! Your Ipaq is Un-Bricked!! Put in your original battery and charge it up!
Enjoy!!
Bless...

hi Rustmonkey,
i have the similar things - i made my hx2110 brick when i flashed it with a different language ROM, it went 100% when i flashed the ROM but didn't work at all after that.
the problem is i can get it in the bootloader mode after trying many ways, at the same time the pc can't find any USB device at all.
how to make it work again?
thanks.

reggaepoo said:
Rusty,
You are so lucky that I experienced this problem and solved it on my own. You did not specify what ROM you were loading, but here is the fix:
First you need to get another pocketpc, hx2000 series like yours that is working.
Put that device into white screen bootloader or pre-BL mode (depending on which device you got to borrow)
Ensure that the battery on that device is 100% charged.
Run the original ROM upgrade for the ROM you wish to install (use PDAViet if it's WM6 and use the HP SP32408 to Run it)
Hit all the Ok screens until it brings you to the one that has the "UPDATE" button.
Remove the working Ipaq from the cradle and place it's 100% battery in you own.
Put your Ipaq into pre-BL mode and put it on the cradle. Press the calendar button to activate the usb drivers.
Once it says "USB", Hit the "UPDATE" button and it will load the proper ROM to your IPaq.
When It is done, perform a hard reset by formatting the PS on the device.
Voila!! Your Ipaq is Un-Bricked!! Put in your original battery and charge it up!
Enjoy!!
Bless...
Click to expand...
Click to collapse
You, my good sir, are a genius - worked great! Fixed BOTH 2110s

tangwd898 said:
hi Rustmonkey,
i have the similar things - i made my hx2110 brick when i flashed it with a different language ROM, it went 100% when i flashed the ROM but didn't work at all after that.
the problem is i can get it in the bootloader mode after trying many ways, at the same time the pc can't find any USB device at all.
how to make it work again?
thanks.
Click to expand...
Click to collapse
You're going to need another hx2000 series to make sure the battery is fully charged - put the battery in and then use the bootloader keystrokes immediately (contacts+itask+reset) - you made need to tap reset a few times while holding the other two to get it to work. After it is in bootloader mode, push the calander button while it is connected to the cradle/usb to get the pc to recognize it

Rustmonkey said:
You're going to need another hx2000 series to make sure the battery is fully charged - put the battery in and then use the bootloader keystrokes immediately (contacts+itask+reset) - you made need to tap reset a few times while holding the other two to get it to work. After it is in bootloader mode, push the calander button while it is connected to the cradle/usb to get the pc to recognize it
Click to expand...
Click to collapse
really amazing !!!!!!
I just saved my hx2110 as per your step by step instruction now.
Thank you very much.

ok, well, I thought they were fixed... now one of them freezes at the bootup screen, even when I do a clean reset... I've tried reflashing multiple times to no avail... any ideas whats going on?

ok, got everything working - reflashed the non-working one back to an original 2003 rom - which made if freeze at boot - then upgraded it via pre-bl to 1.00.00.L - from here, it wouldn't do anything after filling the bar at the boot screen, but it didn't CRASH (as in lights out) - so I ran the pre-bl again and ran the flash program for 1.00.00.L again WITHOUT swapping between the 2495 and the 2110 - just put the 2110 in pre-bl and away we went - flashed, formatted, and booted - then proceed to upgrade to WM6 via 1.00.00.H --> 1.02.00.H --> WM6 - works GREAT!!!
Thanks for the help everyone!

Dear All,
I`ve got the same problem but i don`t have a second ipaq.. is there anyway to repair it with out the second device???
Thank you very much
Abs

Hello,
I have run into some problems with a bricked hx2110.
I was flashing the IPAQ to a new ROM WM5 (Battery was full and I read all the instructions 10 times prior to flashing). While flashing, the progress bar went to 100% then faded out immediately and it wouldn't reset (clean reset). I put the battery in my friends hx3000 series and the battery I used was completely dead. It did flash to 100% though, but not matter how many times I try 1 + 3 + reset, it doesn't reboot. If I can figure out how to get it to boot, that would be great, but I can't get anything to come up with any key combinations.
To this point all I can do is get into Pre-BL mode 1.00.04. I have tried the below scenarios on two machines, both running windows XP SP2 (USB 2.0) with the firewall and virus software disabled.
http://forum.xda-developers.com/showthread.php?t=330382&page=4
1) I have tried the above links directions and used the the Universal Bootloader (Bootloader.exe). It gets to the point where it says "The PDA should be updating now" or something similar but nothing happens. I don't get any errors regarding communications (it sees the device when I hold the "Calendar" button until it says USB; windows then recognizes the device as "HP USB ..." so I know it's communicating).
2) I tried to use the Bootloader_GUI.exe beta so that I can watch the progress indicator but it just sits at 0%. There are no error messages so it is communicating but for some reason, the device won't let it flash (and the flash utility thinks it's doing something).
3) I tried the original ROM flash from HP (SP29856.EXE) and it recognizes the device, but because the current ROM on the PDA is hosed, when it does it's "verifying" process, it comes up with "?" marks as the model number and when it goes to flash it starts at .1% then says "FINISHED" immediately. The ROM utility thinks it flashed it correctly but it didn't flash anything. I'm guessing that the verification of the PDA failed and forced the utility to not flash.
Does anyone have ANY ideas of what to try? I wish I had another HX2000 series PDA and try the "swap" thing prior to hitting the update button but I don't. All I have to work off of it my sad bricked PDA and a full battery (friend keeps charging it). His PDA is an HX3000 series.
Any ideas would be appreciated,
Thanks!

Are you using a the HP flash program that is specified for your device?
2nd - you might be able to use your buddies device in a swap as well - not sure but its worth a shot - use HPs upgrade program, let it verify, then swap your device onto the same cable - overwrite the firmware in the update program for HIS device with firmware compatible with yours and then hit update - let us know if this works...

I am using the "official" HP flash program specific for the HX2110 (from their website - SP29856), bootloader.exe, and bootloader_gui.exe
I wanted to try my friends, but he won't let me touch his because I bricked mine lol (I swore nothing would happen to his but he still won't let me try it).
Anyway, I just copied over the ROM image (from HP) and stripped out the header (now showing 64 bytes before the ECEC). The ROM is for WM2003. I copied the ROM in binary using psdwrite.exe to an 256 MB SD card. As soon as I can get the battery back, I'm going to try to flash it from the SD card. If this fails, I am going to try to play around with MTTY / USB and manually call the ROM flash and see what happens.
Having another HX2000 series would make this easy (maybe a little TO easy )!

Bootloader never worked for me - but if you can get it to manually call the flash, more power to you good luck!

Well it was worth a shot. After spending the better part of the day with the PDA, I have made no more progress (can't get Pre-Bl to update). The only option I have now is to find someone with another hx2000 series that is willing to resurrect it from the dead for me (PM me if you can help - I will pay two way fare). Until that happens, it's going in the "broken" drawer with all my old comp stuff .
Thanks to all the tips and tricks that is posted on these forums and brighthand! There is a wealth of information on this topic and without them, I would have gotten nowhere in trying to repair the device (granted, I wouldn't have been intrigued to upgrade the ROM in the first place and would still have a working PDA, but that's besides the point ).
Best of luck to you all.

1).download original ROM from HP (sp29799) -extract files
2) download http://upload.dvhk.pl/content.php?id=88892 - replace files
3) flesh device.
bay!

link crash http://upload.dvhk.pl/content.php?id=88892 - replace files
Please it can raise it again, thanks

Absolut3k said:
Dear All,
I`ve got the same problem but i don`t have a second ipaq.. is there anyway to repair it with out the second device???
Thank you very much
Abs
Click to expand...
Click to collapse
Same here.. is there another way to un-brick hx2110 on this problem ? thx ...

Solved, my hx2100 returns to be in this world

thank you i saved my ipaq

Error 270 fix

I'm running Vista and when I wanted to run the bootloader upgrade on my Dash I kept getting this message error. Error 260. anybody find any way around it? I've tried to manually set th ephone into bootloader mode, same result. help!! PS the error is supposed to mean "port already open" or "open port error" I'd really appreciate any help!

erro 260 - fixed
switches to my wife's laptop that had XP on and it worked like a charm. I'd be glad to assist anybody in the process od de-branding their Dash. Removing the ugly T-mobile paint logo on the unit was easy too.

ERROR 260
Sorry for thislong story....
OK, I've been on looking around the site for a while. I installed the WM6 Beta. I was looking for two days for the WM5 ROM only because I want the little things to work. Finally found it. But now every time I try to flash my phone ack to WM5 bI keep getting the 260 connection error. The readme only says to restart the comp and phone and try again. I have literally, no joke, done this 12 times in the last 2 hours, hoping maybe it will go. All the phone does is go to the green, blue, and red screen and stays there. Then the comp says it gets the error. I know it's connected because Sync Center syncs, I can look through the phone, install apps from my comp, etc. Also I tried doing the 'Update only' rom for version 1.11 or so, and it starts to go but then says its the wrong version RUU. Has anyone had this problem before? Flashing to WM6 did this once and then worked after.
I'm running Vista Premium, stock sync cable, Microsoft Sync Center for vista. All this is the sameas when I flashed to WM6.

There goes another 3 attempts, trying to change timing, reinstalling Sync Center, etc.

Decided to try it on my XP desktop, and for some reason, first time it worked. Maybe Vista didn't like it? Who knows..

Mladito Vista!!
Hi there,
I have the same little problem here!!!! I have a laptop with Vista (garbage)... so i´ll try on a laptop running XP...thank you for posting this, it was a big help..i let you know how it turns out... see you around

WM5 to WM6 --> Problems at 3%
Hi all,
I've errors upgrading my phone to WM6.
I Can open the Wizard (it`s a generic to S620/S621), but in 3% i`ve an error.
I think thats my phone has a blocked CID.
How can i unlock this? i`ve tryed with tools to unlock, but without success...
Regards,
Emerson

Hello,
Welcome to the forum.
Your problem is that your phone is CID-Locked. Hence, you'd need to use a paid service to unlock it. I personally used the following service which provides instant unlocking:
http://www.gsmliberty.net/shop/htc-excalibur-instant-remote-unlock-p-1452.html
I used a credit card, it's 39.99 $ - I was done unlocking and upgrading to Windows Mobile 6 in about 15-20 minutes.
Good Luck !
P.S:
Steps to install WM6
- First CID/SIM Unlock using GSM Liberty
- Flash Bootloader
- Install WM6 ROM (It will take some time for it to load so give it about 5-10 mins. it does get stuck at the boot screen for sometime but eventually it'll load)
- Install Office/Audio Manager
- Application Unlock your phone using SDA Application Unlocker
- Install the necessary software/tweak/hacks
there you go, if you have any questions, feel free to ask. also, if you use the search function, everything's available here.
Good Luck !
Here's the following links you require
1) Flash Bootloader
ftp://xda:[email protected]
2)here's the WM6 ROM:
http://files-upload.com/files/472108....90_Ship.ex e
here's office for those who want it:
http://rapidshare.com/files/31706137/Office.WM6.zip
here's Htc Audio Manager for those who want it:
http://forum.xda-developers.com/atta...1&d=1183909664
Ps. I better like German flash, it's smaller due to fewer language packs, and contains English, here: http://files-upload.com/files/472422....90_Ship.exe
thanks to jsp_m for the links.

Hi,
I`ve problems because my IMEI is from Brazil...
And in the site accept only 15 digits IMEI..
My imei is: 35*************02 (17 Digits IMEI)
Thanks,
Emerson

hey,
that's not a problem. everyone has 17 digits, don't include the last 2 digits when you type in your IMEI so for example
11111111111111102
just include the first 15 and submit and you'll get an unlock link in your e-mail, follow that link, scroll down to the page to download dashunlock software and download the .UNL file for your IMEI and then make sure ur phone is connected to active sync and it's green, open the dash-unlock program and then hit enter then it'll ask for the .UNL file, locate it and open it and your good to go - your phone will be unlocked then soft reset it or i think it's automatic and everything's set.
good luck !
p.s: in other words, don't include 02 when you type in your IMEI.

HTC Audio Manager
http://forum.xda-developers.com/showpost.php?p=1355010&postcount=5

Thanks!
I'll Try NOW and let all know...
Regards,
Emerson

Arrghhh!!
My phone still give the message:
Invalid Model ID [244]....
And now? i`ve payed 40 bucks for an unlock software....
Thanks,
Regards,

tatarezende said:
Arrghhh!!
My phone still give the message:
Invalid Model ID [244]....
And now? i`ve payed 40 bucks for an unlock software....
Thanks,
Regards,
Click to expand...
Click to collapse
Emerson;
Read the second post from luckybandit on this thread. That´s exactly what to do to get rid of the "invalid model" issue. Download the bootloader, flash the phone, flash the new ROM and be patient.
My excalibur is also from South America, and worked OK. If you have any doubt just let it know to this thread.
Boa sorte!

Hi,
I`ve problems with the link of Boot loader....
Anyone can send the full URL?
Thanks,
Regards,
Emerson

Hello,
I'm sorry about the links not working, here - i've attached the bootloader for you. here's what you do
1) Run bootloader (attached file)
2) Run the WM6 WWE ROM
3) Run SDA Application Unlock
4) Install Office/Microsoft Voice Command/HTC Audio Manager
5) Install Tweaks/Hacks
here's a site that has some applications and tweaks:
http://mobile.surrealnetworks.com/DashApps.htm
and search this forum, there's tons of information, hacks - etc.
Good Luck !

oh by the way, did you unlock your phone properly?
1) Download unlock software
2) Download .UNL file specifically for your IMEI
3) Connect phone to computer and make sure the activesync's icon has turned green
4) Run unlock software
5) When unlock software asks for .UNL file, browse for it, choose it
6) That's it ! It should say Unlocking done and it'll reboot
Your phone is now Sim & Cid Unlocked. If you have more questions, feel free to ask. just do what i said first then post.
Good Luck ! Hope to see everything working for u...

Hi again...
Now i`ve the Error 260 message everytime my phone boots in "Flash mode" (3 color screen)....
Follow my configuration in this screen:
Excalibur Wi-Fi RUU
ONBL 1.15.0000
Excalibur
SPL 1.15.0000
Excalibur IU
ERROR [260] - No connection

tatarezende said:
Hi again...
Now i`ve the Error 260 message everytime my phone boots in "Flash mode" (3 color screen)....
Follow my configuration in this screen:
Excalibur Wi-Fi RUU
ONBL 1.15.0000
Excalibur
SPL 1.15.0000
Excalibur IU
ERROR [260] - No connection
Click to expand...
Click to collapse
Hi,
Are you using Windows Xp? Cause I've gotten that error a couple of times too but it was in Vista. Try Xp if you're using Vista.

Hi!!
DONE with XP.... but now i`m affraid!! The "Green Screen" with nem OS apparently locked... this is normal? at least 3/4 minutos in the same screen.. both "patches" are applyed sucefully....
Is there anything else to do now?

How can i Solve Brick Mode O2 XDA 3

Hi
My device has a German ROM.
I tried to Rom Upgrade to my O2 XDA III PDA but it doesn't work!
when i flashing the device it's freeze on process at%41 and give a error message. i unplugged the device craddle and flash same ROM again and process completed succesfuly. After all when i turn on my device ,there is only 3 Color on screen (Blue - Green - Red) and at the bottom of device is white. it writes R.1.10.00 at the right bottom of the screen.
Sorry about my english ! i searced it on web but i found a information and it tells find same type device and update ROM with FAT 32 Formatted SD Card.
Can anybody help me for Solve This Problem.
Thanks.

1. do you use vista/7 ?
2. did you forget to take out the sim and sd card during flashing?
that would be 2 possible reasons why you had the error in the first place.
now for the solution: if the flash was really complete and successful, which at this point you cannot tell by the success message, have you performed a proper hard reset?
the instructions on how to do that are to be found here: http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
power+reset, record+camera, then set the menu options to No, Yes, Yes confirm with the mail button.
rom upgrade through the sd card is generally not such a good idea, since it has never been fully confirmed, that and how it works.
if the hard reset does not solve your problem, you should read -=this=- really carefully and think whether you really did ALL the steps, they are all equally important.

Problem is getting worst !
Thanz chieff for your Help.
Problem is getting worst and confusing. i updated Radio version to 1.10.00 to 1.15.00. Device is turn on but it doesn't boot. My Device has no camera. When i plug it to creaddle it's orange led is ligthting and randon times it boots and 3 Colored screen shown. R.1.15.00 D.****** G******
HTC Blue Angel Windows Mobile 6.1 WWE only. But now it's do nothing. This morning i made hard reset to device and shown SERİAM V.2.07 and put ,t to creedle and tried to Urgrade room but it gives error random positions etc. %54 or %89. ERROR 112
is my device dead???
Thanx you very much for helping me.
(Sorry About My English )

About my OS
i tried to upgrade XP Pro (SP2). Vista and Windows / is Not permission to upgrade...

if you're giving up, mail it to me. i should be able to tinker with it.