Related
Hello all
My artemis won't turn on anymore. I managed to do an hard reset but when it got to resetting the device, it will not start again. Tried removing the battery for some time, but no results.
Only thing I'm able to do is start the bootloader and use mtty. Is there something I can do from there ?
Regards
Hello,
I had the same problem, ended up with service - took 3 weeks (Norway). In the beginning it happen once or twice a day, managed to turn it on but after a few weeks it didnt start at all.
Best regards
BA
I had the same problem today on my Orbit. I started the GPS (igo 2006) this morning, and it started calculating a route from my present location to somewhere really far (forgot to reset the route). It became unresponsive, so i decided to soft-reset.
However, it wouldn't turn on... I removed the battery, sim, and microsd card for an hour, and tried to start, but no luck. Soft-reseting didn't do anything either. When I got home, I plugged it in to charge, but no go... the charging light stayed off, and a soft-reset wouldn't work.. wouldn't even power on!
Finally, I pressed the voice tag button (top left button on the side, beside the volume slider), and the soft-reset button togther for a couple of seconds... and it booted up like normal.
Not sure if this is a permanent solution, but I'm going to back-up everything daily from now.
Try it... might work for you.
N.
hi guys,
has anyone experienced a problem where their Trinity will not "wake up" with the short press of the on/off button?
I'm sure I read about this some time ago and am trying to work out if it's hardware or OS related.
I'm running mUn's TE WM6 which I have been for many months now.
The problem has only started in the last 2 weeks or so.
I haven't installed anything new, but have enabled Push Mail for OTA mail.
It's doing it 1 or 2 times a day now and is very frustrating. The only way to wake the phone is soft reset.
When calling the phone from a landline, it does not ring and goes to voicemail.
Any advice or solutions gratefully received.
no one seen this then I guess.
Bummer (for me!)
Try hard reset
sickboy555 said:
hi guys,
has anyone experienced a problem where their Trinity will not "wake up" with the short press of the on/off button?
I'm sure I read about this some time ago and am trying to work out if it's hardware or OS related.
I'm running mUn's TE WM6 which I have been for many months now.
The problem has only started in the last 2 weeks or so.
I haven't installed anything new, but have enabled Push Mail for OTA mail.
It's doing it 1 or 2 times a day now and is very frustrating. The only way to wake the phone is soft reset.
When calling the phone from a landline, it does not ring and goes to voicemail.
Any advice or solutions gratefully received.
Click to expand...
Click to collapse
Try hard reset
softreset helps, sometimes i have the problem with windows mobile 5 too
jmermel said:
Try hard reset
Click to expand...
Click to collapse
thanks John.
But do you have any fact based reason for this suggestion?
I'm happy to give it a go if there's more than 50% chance it will work.
Hard reset
sickboy555 said:
thanks John.
But do you have any fact based reason for this suggestion?
I'm happy to give it a go if there's more than 50% chance it will work.
Click to expand...
Click to collapse
You might have loaded a program that is not liked. Use a backup program. If this does not work then load your backup after the hard reset and you will be back to where you started
P3600 with D810 WM6 ROM; also happens occasionally, recovered with soft reset. Seems to happen most often when I press the On/Off button twice too quickly.
thanks guys.
I'm going to try the hard reset route-I'll report back.
Some time ago this happened to me so often, but said it was due to some application, in my case was Slide2Unlock.
Since I removed by their consumption of memory it didn't happened to me.
(Sorry for my english)
Bugger, this has started to happen to me as well. Only 3 times in the last 3 days but if it keeps is up that will be enough for me to do a hard reset (overdue). Strange cause the only new thing I put on in the last week has been PCM 16 which is only a copy/paste exercise.
The fix in the Hermes forum is to force your device to sleep and not let it go into standby.
I have had some problems recently with DeviceLock 1.2 just ceasing to work and have to uninstall/reinstall to make it work again. I set it to turn the screen off when locked, as this does not put the device on standby, maybe there is the same issue with it going into standby by itself.
I have the same problem..i think that it has to do with the phone hanging..most probably due to some background programs eating too much power and memory and the phone just lacks till it hangs..happens when you have other programs that have hanged as well..my problem is with PocketAlarm..it takes so long to load my phone went to standby and the phone couldnt be called back..in brief the phone just hangs because of a program..i don think it has any problem do to with the hardware or strictly the OS..cant really explain..but the role the OS play in this problem is that it allows the program to make full use of the phone till the phone cant cope with it..its the core of the OS so it cant be avoided with any other versions or anything..sorry it seems rather unclear..hope you guys understand..
same problem for me ... from times to times, when a call hang up, i push a lot of times the red button for going back to the today screen and as it shows up, i click immediately on the Power button for turning off the screen. right after when i forgot to do something (approx 1sec) i push the power button and there it doesn't turn on the screen ... strange ...
what i've installed on it :
TomTom 6
BatteryStatus with today plugin ver 1.04.203 beta4 i put tray icons too.
i've bluezard for sniffing and/or hacking bluetooth devices.
OBDgauge too it's a software that works with a bluetooth dongle i plug into the diag port of my car.
and that's all. ah yes one more thing -> i disable the "HTC Home" because i don't like it.
Same problem here...
Still no solution?
I got this problem from some version of rom by Karmba. But V7.2 is OK so far. It seems happened when I close Egress reader by click X button then turn off screen by power switch. It then would not wakeup again. But if I close Egress and check the running programs from Task Manager to make sure the Egress is not running at the background, then I can turn on or off the screen freely.
So I think this wakeup problem is caused by some running program that was not closed properly by X button then crash the WM.
That was just my personal finding. Hope it help you guys a bit.
Hi.
My Artemis doesn't turn on, and doesn't even charge.
I don't know what has happened, it was in suspend mode, i pressed the power button, and the screen lights up all white.
I had to remove the battery to turn it off.
Now it doesn't do anything. I tried the soft and hard reset, but to no avail.
Is it dead?
PS: I left it without battery for a couple of hours, and it turned on, but then the screen turns all white, and it's dead again.
boot problem
Hi,
I have the same problem.
It doesn´t turn on and it doesn´t charge.
I don´t know how to flash the artemis. I can not enter in bootloader mode and I can´t sync it because activesync doesn´t work.
I remove the battery too but it turns off. I tried a soft and hard reset but
It does nothing.
any solution? please
Thank you
had a similar problem last month too. sent it back to htc authorised service dealer and was diagnosed with a faulty motherboard. luckily, it's still under warranty and they changed the MB. all functioning well now..
I've had five different motherboards and I'm still in trouble - I suspect there is a bad batch out there, as my original worked fine for about six months.... since then (its a long story.....)
Hy.
I have the same problem, can't even start by bootloader, sincer my batterry run out, i can't power up my artemis, any reason why ?
The battery is full .I tested on another artemis .
Edit: The only wrong thing I guess i did was flashing it to a touch rom, but it was all good till it run out of battery, if I sent htc to the warranty, they won't fix my problem because of the rom right ?
Hey guys, hoping you can help me with a problem with my harrier.
It was was working perfectly fine, and I replaced the touch screen (original screen was cracked) and it seemed to be working perfectly fine.
However one time, the battery fell out, and when i put it back (and ever since then) it showed the Pocket PC 2003 startup screen, and won't go any further then that.
Reseting didnt work, so I tried discharging the internal battery (by leaving the the battery off it for several hours), and then charging up the battery and charging up the internal battery.
That broke the cycle, now it showed the Welcome to Pocket PC, please touch the screen to continue - however touching the screen did not have any response. I tried hard reseting, and what do you know, back to the boot up screen only cycle.
Another thing, the boot up screen as soon as you turn it on, and then you can't turn it off and it's completely unresponsive.
I thought it's possible there was a loose connection inside, from when i took it apart, but i took it apart again and plugged everything in again, but it's still doing the same thing ~_~.
Does anyone have any ideas whatsoever?
Thanks!
Willuknight said:
Hey guys, hoping you can help me with a problem with my harrier.
It was was working perfectly fine, and I replaced the touch screen (original screen was cracked) and it seemed to be working perfectly fine.
However one time, the battery fell out, and when i put it back (and ever since then) it showed the Pocket PC 2003 startup screen, and won't go any further then that.
Reseting didnt work, so I tried discharging the internal battery (by leaving the the battery off it for several hours), and then charging up the battery and charging up the internal battery.
That broke the cycle, now it showed the Welcome to Pocket PC, please touch the screen to continue - however touching the screen did not have any response. I tried hard reseting, and what do you know, back to the boot up screen only cycle.
Another thing, the boot up screen as soon as you turn it on, and then you can't turn it off and it's completely unresponsive.
I thought it's possible there was a loose connection inside, from when i took it apart, but i took it apart again and plugged everything in again, but it's still doing the same thing ~_~.
Does anyone have any ideas whatsoever?
Thanks!
Click to expand...
Click to collapse
you could try flashing it back to 2003 use a shipped rom you ma still be able to download one from the service providers site or from the ftp read the ba wiki good luck
swampy395
yes!!!
Willuknight said:
Hey guys, hoping you can help me with a problem with my harrier.
It was was working perfectly fine, and I replaced the touch screen (original screen was cracked) and it seemed to be working perfectly fine.
However one time, the battery fell out, and when i put it back (and ever since then) it showed the Pocket PC 2003 startup screen, and won't go any further then that.
Reseting didnt work, so I tried discharging the internal battery (by leaving the the battery off it for several hours), and then charging up the battery and charging up the internal battery.
That broke the cycle, now it showed the Welcome to Pocket PC, please touch the screen to continue - however touching the screen did not have any response. I tried hard reseting, and what do you know, back to the boot up screen only cycle.
Another thing, the boot up screen as soon as you turn it on, and then you can't turn it off and it's completely unresponsive.
I thought it's possible there was a loose connection inside, from when i took it apart, but i took it apart again and plugged everything in again, but it's still doing the same thing ~_~.
Does anyone have any ideas whatsoever?
Thanks!
Click to expand...
Click to collapse
Soft reset to your BA, before the red software letters appear in the splash screen push camera and record buttons simultaneosly , if you do correctly simultaneosly three labels gonna appear, with camera and record buttons you can choose the labels and set "yes or no". set all to "yes" exept KITL, after do it press message button and your BA begin to boot, dont afraid for the white screen it take a moment
did you sort it? - I have been through this exactly. Pressing the camera and record buttons does not do anything in wm2003 and there is almost no delay before the boot screen appears.
I reflashed mine with ship roms and in all cases the BA froze at exctly the same place. Amazingly enough I fixed it by letting the internal backup battery go completely flat (took the main battery out for a few days), flashed with fresh ship rom and all was fine. Even works great with WM6.1
Worth a try, I tried so many things and none of them worked I was going to throw it in the bin, amazing how easy the fix was.
thanks for the replies.
Currently trying to find a rom for a CDMA blue angel.
Try this post, it does work on Vista.
I know that it is an o2 rom but will be fine then follow the steps to upgrade as before
Try this link
http://forum.xda-developers.com/showthread.php?t=281959
Hello,
I have a strange problem with my HTC Artemis (O2 XDA branded, bought in Germany, no lock)
It behaves unstable and indeterministic.
Unstable means that it crashes/stucks or turns off.
Indeterministic means that it happens when i plugg it to charger, when i'm syncing, when a phone rings, when using applications/tomtom or just i arrive to work and i find the device off.
When it crashes or i find it off, the biggest problem is to boot the device. It takes me typically 10mins, when i'm always trying to press the power button, push the reset button or unplugg the battery for a while in random order until i bring it to work.
After first crach, the device also often crashes or stucks again during the boot process.
Once, the device was so dead, that it took me two days to bring it into bootloader mode and then i could at least flash the ROM.
All these was happening with ARTEMIS TOUCH 4.01 WWE - LITE NO CUBE.
Yesterday, i switched to ARTEMIS TOUCH 4.02 WWE - LITE NO CUBE (burned FW twice) without installing any other applications and the problems are still here
My personal feeling is that it is getting every week worser.
When i bought the device (eBay), there was original FW with Win Mobile 5 on it, i immediately flashed to ARTEMIS TOUCH 3.01(?) WWE - FULL WITH CUBE, i can only remember that that time I had a problem with gsm radio - from time to time i found it stucked/off - to bring it to work i had to reset the device. So i flashed to 4.01 and this issue was away, but approx 2months ago, the above described behaviour has started and nowdays i'm fighting with it 2-3x a day.
so, can anybody help?
GiZMo
Similar here
I have a similar problem, what's really strange to me is, that as far as i can recall it started happening 2 months ago or so also!! weird huh...
my device simply reboots from time to time! even while i'm making a call.
the weird thing about these reboots is that when it comes back to live i do not have to enter my pin to enable the phone! everytime i perform a manual reboot (by software, using the pin or remove battery) i have to insert my pin to able to make a call...
i have upgraded from 3.01 full touch to 4.02 full touch about the time it started, i have now 4.02 vanilla touch but problem still occurs from time to time.
any ideas?
Im another one to join this boat!
Bought an MDA C 3, two days ago, bought of someone from gumtree.com.
Worked fine for the first hour, and then locked up - nothing on the screen, no LED. Only way to get it going was to remove battery and then press power button.
I upgraded the ROM from the original t-mob UK WM5 to mechles fine release: http://forum.xda-developers.com/showthread.php?t=371182
The lock-ups / crashes have now become rarer, on average every 4 hours (before was every 1 hour).
There is no pattern to them either, although I have saw the screen trun all corrupted just before it happens. The last one was caused when I pressed the 'start' button.
I'm on a T-Mob contract, and lost my Kaiser, got ripped of when I tryed to replace it by a tosser on here for $375 Thief on the loose thread, and was hoping my luck had changed when I bought this one!!
It is T-mob branded and I wonder if there isn't a fix on here, would T-Mob repair it under warranty??
same "issue" with no entering of PIN after reboot. But not always
GiZMoSK said:
ARTEMIS TOUCH 3.01(?) WWE - FULL WITH CUBE, i can only remember that that time I had a problem with gsm radio - from time to time i found it stucked/off - to bring it to work i had to reset the device.
Click to expand...
Click to collapse
here i found a good description of that issue:
"
Originally Posted by lasertony
I've got the same problem as !Novy, but nobody seems to have noticed his question. Are there any other guys out there with this strange problem ? I have been using this rom for a while and sometimes, without any visual warning the phone freezes up. This is particularly ennoying because there is no way to check wether it is working or not. Every other function or software keeps working ! The phone is just not receiving any calls or sms. So you can miss an entire day of calls and sms without knowing... Only when trying to call somebody the dialer says 'Dialing...' and nothing happens. No connection.
A soft reset is needed to get the phone working again.
"
btw, now i'm again trying to turn the device on, it's again stuck. grrr
Hello,
i had a few weeks ago a similar strange behaviour.
After changing the sd-card I had problems to turn the device on. After a hard reset it began to boot but hang.
The I flashed back to original O2 ROM. Then I had a unpredictable behaviour. Somtimes no sound. Sometimes I cound not be called. Sometimes Error message "no sim card". After every reset i had an other error.
Hard reset and flashing was no solution. Removing battery for less than 4 hours has no effect.
Then I wanted to send it back for repair. I took of the battery. The next day I wanted to try a last time and surprise: The device works fine without an error. Its hard to believe, but the removal of the battery for more than 8 hours was the solution.
Now I use it for 5 weeks without a problem.
regards
Andre
It is Happening to my device too!!
It stucks every 2-3 hours!Tried many of the cooked ROMs but nothing.Also tried all the radio roms for 1-2 days.still the same!
It stucks with no particular reason.SOmetimes in s2u2 sometimes when am receiving a call.... etc.
Had the pin problem too for 3-4 times!
I will try your sugestion ANDRE and we will see!
Also i will try flashing the original rom,cid unlock and then flash the cood rom twice!
Fingers crosed....
Andre1210 said:
Its hard to believe, but the removal of the battery for more than 8 hours was the solution.
Now I use it for 5 weeks without a problem.
Click to expand...
Click to collapse
didn't help
happy u
now, i will try to flash back original german o2 rom
I think mine is sorted now, thanks to a new battery.
Installed it on Wednesday and hasn't died/crashed once since then.
I did notice before that the battery was getting warm, and I stuck the handset on the vent of my AC in the car, and this seemed to make the phone more stable.
Got one from Deal Extreme or try the XDA shop.
It worked for me!!
bricked or not?
did my device get bricked?
last friday i wanted to change firmware and during step1-cid unlocking (device should never been cid locked) pda got stucked. So i unplugged it and since then i cannot turn it on or get it into bootloader mode.
the only proof of life is when I take away battery and plugg it to power supply, then the red diod turns on and off for 1/2sec.
any idea what to do?
Vinnie1 said:
I think mine is sorted now, thanks to a new battery.
Installed it on Wednesday and hasn't died/crashed once since then.
I did notice before that the battery was getting warm, and I stuck the handset on the vent of my AC in the car, and this seemed to make the phone more stable.
Got one from Deal Extreme or try the XDA shop.
It worked for me!!
Click to expand...
Click to collapse
I thought it was a battery problem too, but I've 2 batteries and both are died in the same time? I think it's too strange...
My P3300 have this problem from when it is returned from assistence and with original firmware (without other applications).
dude i think u bricked ur device i am sorry to convey such a message!
now its time for CPR go to xda wiki and try the SD flashing get ur device back to life man
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
GiZMoSK said:
did my device get bricked?
last friday i wanted to change firmware and during step1-cid unlocking (device should never been cid locked) pda got stucked. So i unplugged it and since then i cannot turn it on or get it into bootloader mode.
the only proof of life is when I take away battery and plugg it to power supply, then the red diod turns on and off for 1/2sec.
any idea what to do?
Click to expand...
Click to collapse
jahrami said:
dude i think u bricked ur device i am sorry to convey such a message!
now its time for CPR go to xda wiki and try the SD flashing get ur device back to life man
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
Click to expand...
Click to collapse
but i cannot get into bootloader mode so no flashing from SD card or PC
bricked device
so my device ist still dead
is there any possibility to hard flash bootloader (when corrupt)? or the only way is to change the mainboard?
GiZMoSK said:
so my device ist still dead
is there any possibility to hard flash bootloader (when corrupt)? or the only way is to change the mainboard?
Click to expand...
Click to collapse
the good sign are the leds that means you have a very good chance...the guy made the piont...check the wiki
random crashes are often caused by hardware malfunction...sometimes the connection on the motherboard stuck,get broken or make a short-circuit...so check the hardware