Does anybody know whether it is possible to connect a USB GPS mouse via USB cable to the Universal? Universal should be able to act as a USB host, so it might be possible. If yes, any ideas on external power supply? Maybe via USB cable splitter?
Thanks, the Modifier
No-one's yet posted to point out that the Universal cannot act as a USB host, not sure if you've been PM'd yet - I thought I ought to point this out just in case someone saw this thread and thought it confirmed that the device did.
IIRC from reading other posts, it is not possible to connect a GPS mouse via cable to the Universal. I would imagine that this is a drivers issue though (?) as the 4 pins on a usb connector should be able to deal with v+/-, rx and tx...
Anyone care to comment on the feasibility, I would prefer to be able to use my serial GPS unit than buy a new one (well, ok, no I wouldn't, I want a battery powered SirfIII BT device I can use on my mountain bike and this is a great excuse, but I *ought* to use my existing gps box! :lol: )
It's not a driver issue, it's a hardware issue. Physical bits for a host are different than for a client USB device. The Jasjar (Exec) is a client device and you aren't going to be hooking another client to it.
Related
I'm not very up on how USB works. Is it completely standard?
I was just wondering if there is a mini-usb full-sized keyboard or any other accessories that might work with the universal?
Do PDA's just need drivers and an interface and they can run anything like a PC? With the mini USB port on the Universal is it likely that any mini-usb accessory could work? I saw somewhere that it works with an IBM external HDD, would this also apply to the ZIP disks and stuff?
This is interesting BTW: http://en.wikipedia.org/wiki/Universal_Serial_Bus
you can get cables which have mini usb in one end and any type of usb connector in the other
yes pda's require drivers just like pc's
but that may not be enough
if the pda dont support host mode it would be like trying to connect your
external harddisk with your usb mouse
http://forum.xda-developers.com/viewtopic.php?t=26742&highlight=usb+host
http://forum.xda-developers.com/viewtopic.php?t=28477&highlight=usb+host
Bummer
Oh well.
I'm quite happy if someone wants to delete this thread by the way.
Hi,
I am looking for cable that I could use to connect my JasJar PDA (USB mini port) with GPS (USB mini port) and car lighter. This cable should transmit data between PDA and GPS. Also it should power PDA and GPS from car lighter socket. Look at attached picture for better explanation.
Do you know where I could buy it?
Best regards
Marek S
Cześć!
Myśle, że nawet jeśli masz taki kabel, to będziesz mieć problem. And there my Polish runs out!
(trans: Even if you had such a cable, you'd still have a problem).
Or at least I would assume so... Even if you made a mini usb to mini usb cable with power spliced in from a car adapter (easy enough to do after all) then you would still have the problem of persuading your pda to use the usb connection for rx/tx gps data, which I would have thought was a drivers problem...
Anyone?
Hi,
As I read on some forum this device can work as USB host and WM 5.0 has many drivers also for GPS devices. Is that true? If it is, problem how JasJar will communicate with GPS is not a problem. The problem for me is that I cannot make that cable myself and I need sombody help.
Best regards
Marek S
Sadly, this device cannot act as a USB host... I am frankly disappointed that they decided not to implement it, but I guess there always has to be a reason to upgrade to the next model!
I'm afraid I don't know about WM05's support for GPS devices connected via USB, although I think I have read in other threads that people have tried without success to connect GPS receivers to their Universals.
I bought a BT gps receiver to use with mine, and am hoping to cover the cost of that when I sell my IIs, wired gps receiver, cradle etc. One thing that attracted me to the Holux that I bought is that it can apparently be used as a gps mouse if you buy the optional cable - a usb to usb mini that has a curious small plastic junction box halfway along it's length. I assume that there is some form of jiggery pokery going on in there (like swapping the 2 data lines or grounding something ) because I certainly can't connect my receiver to a laptop with a normal usb to usb mini cable.
Sorry I can't help more, but I think you may be stuck unless you can find someone locally who'll chop up some cheap cables for you to experiment with... :?
I am wondering whether if you got a Minu USB to USB B, plugged it into a cheap powered/unpowered hub, the to the GPS would it work?
If it is a cheap hub, when powered, it may have the 5V rails joined, in which case the power might run back to the universal.
However, before testing this, it would be wise to test that the USB can work with teh GPS on its own. If you do not have a mini USB A to mini USB A already and tested (I couldn't see such cables) then www.maplin.co.uk could supply you with the following, which would/should provide you with a connection if it is at all possible:
mini USB A to USB A (Standard with universal surely?)
Female USB A to USB B
Female USB B Female USB A
USB A to mini USB A (Standard with universal)
That is a lot of cables
This cable should transmit data between PDA and GPS.
WHy on earth would you want that?
JaySea said:
This cable should transmit data between PDA and GPS.
WHy on earth would you want that?
Click to expand...
Click to collapse
Once you can prove that the PDA can connect to the GPS that way (one of the posters was not particularly positive on that) then the addition of the HUB would allow you to put the power onto the cable.
Gareth
kabel...
Hi Marek,
This is not going to work for DATA but this kind of cable may work to charge both JasJar and BT gps. Log in to www.allegro.pl , find covox in "szukaj użytkownika" go and buy the BT gps with the mini usb port (like G-Space GS-R238) and solder in second usb mini cable into the included car charger .
thats all...
This should charge both....ordered one and am waiting for it, doubt it'll sync though.....
http://cgi.ebay.com/Motorola-Blueto...yZ108660QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Does this exist? I'm about to purchase an HTC P3300 and I would like to use a car diagnostic software call "VagCheck". To use it, you need a cable to connect from the the PPC to the cars OBDII port. These cables only come for iPaq ppc connectors to OBDII, serial to OBDII, and USB to OBDII. These cables are expensive and I already have a serial to OBDII cable. So I'm looking for some kind of way to connect the cable to the P3300 via the mini USB connector but I know there will need to be some drivers involved.
Does anyone know if there's an adapter from mini USB to regular USB or Serial for PPC's with drivers?
BTW, there is a more expensive alternative. There's a bluetooth connector for the car that plugs into the OBDII and you can just connect via BT. But that is the most expensive set-up.
USB to serial
I guess you can use USB to serial converter, which is inexpensive.
Thread moved.
AFAIK the P3300 is USB client only, which means it can only be used as a client device to a PC. USB host capability is required to work with USB peripherals such as a USB to serial adapter.
So basically what you are trying to do won't work with the P3300 unfortunately.
The only way around this problem would be to get a bluetooth-serial module which would connect to the serial - OBDII unit and allow the P3300 to connect to it via bluetooth.
A bit silly I know, this is the result of most PDA manufacturers choosing not to equip their devices with USB host capability.
Antzzz et al,
You're right.. The current HTC range are all only USB Client.. So you can't connect an HID device, serial adaptor etc.. There IS rumoured to be a set of serial pins on the non-standard Mini-USB style connector on the D810 device range - however, we've never seen a cable that breaks out (or explains the RS232 pins)..
Does anyone have a full pinout of the extended connector??? This might be a project for further investigation.... ?
There are a few industrial RS232 to Bluetooth adaptors, such as :
http://store.pressdigital.com.au/industrial-bluetooth-serial-adaptor-rs232-p-5092.html
But they're expensive as a rule.. You may want to grab a Bluetooth OBDII interface.. (or another cheap PDA with RS232 like a cheap low-end iPAQ hx2490).
Let us know if you stumble across the RS232 pinout on the extended D810 connector.
Cheers
Andy
www.pressdigital.com.au
Support Team
i am having the same problem. i have a xda orbit with some software on it to adjust my air suspension on my car. i have tried connecting the cable supplied with it to a serial lead and then the obd11 lead but i could not get it to work. just found a Original O2 XDA Serial Sync Cable . ordered today from
http://l8shop.net/products/Original-O2-XDA-Serial-Sync-Cable-3280.asp
if you have any success in getting yours to work i would appreciate any help.
Quite a lot PDAs supporting USB-host, but for only a few an adapters or appropriate cables from the manufactures are available.
As these devices support USB-Slave as well I would like to know if there's a way to convert the USB male connector (used as slave e.g. for sync with the PC) to a USB-host female in order to connect accessories (keyboard, mass-storage devices...).
According to wikipedia the configuration of the pins shouldn't differ too much for slave and host mode.
Pls. see attachement, that's what I found regarding this question. It's a picture showing a similar configuration (as new user I'm not allowed to post external links, thanks to ab21cn
from xdaflameusers)
But it's a male-to-male converter and furthermore a converter from "big usb" to micro (mini?) usb. As there're already standard converters for the different sizes of USB I would like to start with the biggest size and to buy the appropriate converter as needed.
Does anyone has a circuit diagram or any other idea for such a generic converter?
Try adapters made for Nokie N800 series
I had a Nokia 770 a couple of years ago. It came as USB device only with mini USB connector, but online I found how to upgrade the software to USB host, and use a cable adapter. The plans I found online involved a 9V battery and 5V voltage regulator inside a metal case (they used a penguin mints case). I built one of those, even using the penguin mints case, and it worked fine.
I have never seen any indication that my HTC phone would work the same, but I am guessing that it might, if the USB host drivers are available.
Google couldn't locate the penguin mints-based converter I originally found, but this seems to be a similar circuit diagram.
Edit: Found it!
thx
thanks for the links. but i'm a little bit afraid of connecting something to my pda which has an own power supply, the risk of a burn-out is given. i've got a nautiz x5 with 4400mA battery which should have enough energy to supply usb-power to connected devices.
I think I'm going to contact the manufacture of my device, maybe this works for me, but a generic adapter would be of use for anyone.
the chips used for usb should be of the shelf as i don't think each manufacture develops an own logic for usb... but this doesn't imply that the cabeling is standard too.
what the heck makes manufactures providing features in their products which the users can't take advantage of?
do you mean using keyboards and so on on ppc?
because it's so simple if ur phone has a mini usb plug (the one u plug the power adapter into). i found a cable that plug into that and plugs a normal usb cable in on the other side and blam been typing on my phone using a desktop keyboard. it depends how much power your device requires however. i wish there was some software to feed a video line out so i could watch videos on pair of vizors that wud be rad. all i can find is a mini-sd card converter now whats the point of that. guess i need an itouch
yes
primary i want to connect usb mass storage devices to my pocket pc. gamecontroller or keyboard would be a good thing too.
my devices doesn't have a standard usb plug, the only thing i got is a adapter from the properitary plug of my device to standard usb male connector, but this is meant for usb-slave use only.
the underlying qeustion is, if there's a way to convert usb-slave to usb-host using the same pins. if it needs an additonaly pin then i don't see a way to convert it as i don't know anything about the pins cableing of my properitary plug.
a week ago i found an adapter which was able to convert the male usb to another male usb... but it didn't work.
the problem is compareable to datatransfer between two pcs via usb - it's possible, but only using properiatry hardware and drivers...
so i think there's no way to solve this problem in a generic way.
out of interest, do you already have windows CE drivers for the device to act as a host and mass storage? I wouldnt mind them if you can point me somewhere..
how to check if my htc (touch2) ca use usb host?
with all the coverage the motorola laptop has been getting these days (google: motorola lapdock rikomagic or motorla lapdock raspberry pi )
I got one to toy around with it my self. I'd really like it to work with MHL devices. Thats the moment I found out that MHL's micro usb in is to charge the device and get the HDMI out to work, but doesn't pass though and more usb data though. I imagine the bandwidth is too great.
So as a consolation I thought it would be cool if the lapdock's mouse and keyboard were bluetooth, then i could connect to its display with hdmi, and control the phone with the bluetooth input.
Does anyone know if there is a generic usb device that allows you to connect a USB keyboard and mouse and then transmits though bluetooth? alternatively does any one know of any relevant mods that might help me hack this together?
The problem with MHL is that it uses the electrical path from the USB connection.
The problem is not bandwidth, it's wires.
All of the funny things that plug into a micro USB connector just use the same 5 pins that are already there and repurpose them.
This includes "Carkit", which is the analog headset/ handsfree connection or MHL.
usb flash is also possible to connect and then not get what you
If you wanted to be really hard-core you could add another micro USB connector to your phone.
You'd have to pick off the USB signals as they come out of the PHY interface and before the main connector multiplexer.
Or you could get the guts out of a trashed BT keyboard and wire it to your Lapdock keyboard.
You wouldn't have to get the layout correct, you could just fix /system/usr/keylayout.
gltovar said:
...Does anyone know if there is a generic usb device that allows you to connect a USB keyboard and mouse and then transmits though bluetooth? alternatively does any one know of any relevant mods that might help me hack this together?
Click to expand...
Click to collapse
I looked and haven't found one. However, during the search I found the KBtalKing Pro mechanical keyboard that solved my problem (well, when it is officially released next month)--it will allow me to use it as my main desktop keyboard (which should be great to type on due to the use of mechanical keys), and also pairs up to 10 devices via Bluetooth as well as one main USB device (probably the main computer). Looks like I'd be able to type on my Android, iPhone 4, PC or Mac simply by pressing a couple of buttons on the keyboard to switch over.
Probably not the economical USB to BT conversion you were looking for, but it's a solution and then some.
You can check out handheldsci com/kb it looks like what you want.
Hi,
Did someone try up this handheldsci adapter ?? It looks indeed as the solution to use any input device/combo without using the usb connection (very useful for smartphones).