MDA III help!!! - MDA III, XDA III, PDA2k, 9090 General

I can't restart my MDA III, It's died. Display appeared only the words:" Serial v 2.05"!!! I have tried hard reset but not operate at all. anyone knows how to restart normally..plzz helps me!!

You need to flash your rom. Search this forum to see how.

how to do it??? Lam the nao ha ban??? giup minh voi

Look for the link in my signature.

I can't solve this problem with all following instructions with holding power button and press reset or hold power button and camera button and reset .... but display allways appear with this words "serial v2.05"
anyone has other advice ????..thanks in advance!!!

Sigh....
OK, first READ:
http://wiki.xda-developers.com/index.php?pagename=BA_GettingStarted
Then find your ROM ship version here:
http://wiki.xda-developers.com/index.php?pagename=BA_Upgrades
Then reinstall the ROM to your MDAIII.

thanks for help but my device can't synchronize with ActiveSync, how I can update ROM.... Display allways appear Serial v 2.05, Can you show me how to synchronize with device first???

No need for synchronization.
TIP:
1. Remove PDA from cradle.
2. Reboot your PC.
3. Replace PDA back in cradle.
4. Install new ROM.
Should work.

Related

O2 XDA Exec Dead after interrupted Rom Upgrade :-(

Hi,
I was upgrading my XDA Exec using Xda_Exec_Upgrade_v1.30.162.exe
My laptop died. It sometimes overheats but it hadn't happened in a while.
I now can't progress past the bootloader even after full clean reset.
Anyway. I have the O2 screen reading:
R 1.04.01
G 42.37.P8
D 1.13.82 WWE
My laptop detects a USB connection, although it says "USB Device Not Recognised". Activesync 4.1 won't detect it, however, I've tried changing settings etc but to no avail.
I've trawled the board here and found people recovering from similar situations with other devices. Am I gonna be able to restore my beloved exec from paperweight-status?
btw: am in Ireland where O2 don't support the exec and bought it from a guy in the UK who got it as an unwanted upgrade. have flashed it before just fine...but don't think I'll be able to return it to O2 as UK and IRL are not the same company...
Help?
Mark
p.s. ran BL10_RUU_UNI_V11.exe and got 101 connection error :-(
EDIT:
Fixed, using bootloader mode and re-running the upgrade. thanks
xda neo crash
You need to reinstall your windows mobile 5 system. If you are using orginal german neo rom, you can download rom from o2 web site, or you can download from this sites ftp server
thanks for the feedback,
I found the info on restarting in bootloader mode (i had previously misunderstood "bootloader") and was able to re-flash it by USB no probs.
I now have a happy XDA
Hello there ...I have about the same problem with my MDA Vario....could you explain how do I "restart in bootloader mode"?
My PPC just stucks before loading windows...
thanks
How to get bootloader mode
Ok, did a bit of a lookaround and got this (I thinkg the MDA Vario is the XDA Mini)
For Xda II and Xda IIi
- Press & hold the power button
- Press & hold the D pad (5 way directional button)
- Push the stylus into the soft reset hole - until you see the word 'Serial' on the screen.
You should now be able to follow the upgrade process above for a device stuck in Bootloader mode.
For Xda IIs
- Press & hold the power button
- Press & hold the Camera button
- Push the stylus into the soft reset hole - until you see the word 'Serial' on the screen.
You should now be able to follow the upgrade process above for a device stuck in Bootloader mode.
For Xda Exec
- Press & hold the power button
- Press & hold the Backlight button
- Push the stylus into the soft reset hole - until you see the word 'Serial' on the screen.
You should now be able to follow the upgrade process above for a device stuck in Bootloader mode.
For Xda Mini S
- Press & hold the voice command button
- Push the stylus into the soft reset hole (short quick press). Keep hold of the voice command button until you see the screen with multicolored horizontal stripes). The device is now in Bootloader mode and you can follow the upgrade process above for a device stuck in Bootloader mode.
EDIT:
The rest of the process (just in case you need to know) is as follows:
(and if you have problems open your connection settings in activesync and ensure that USB is unchecked...that is OFF. remember to reset the USB settings once you've successfully upgraded)
in 'Bootloader' mode
When this happens the device screen will be blank except for the words;
Serial
v 1.00a
The word 'Serial' should change to 'USB' when the cradle is plugged into the PC, and the version number below this will vary. When you get this screen, a soft or hard reset will not make any difference.
It is still possible to run the ROM upgrade file again, WITHOUT using Activesync (activesync will not restart anyway).
Firstly unplug the USB cradle and reboot the PC
Plug the cradle back into the USB port (this must plug directly into the USB port and not into a USB Hub/adaptor).
Now run the ROM upgrade file again from the PC. This should just run as per normal and correctly reflash the device.
Thanks bob_jesus!!
I am already in bootloader mode....Could you tell me where I can find the files to flash it? My device is Tmobile MDA Vario. Are there different files for flashing for every device? (O2 XDA mini s, MDA Vario, imate kjam...)??
Thanks again
Hi Ermoscow,
I'm sure if you trawl around the boards a bit you'll find it. I'm pretty new to this but yes, all these devices tend to have a different Rom, and each device itself tends to have a different Rom based on your mobile carrier.
e.g. I use an XDA exec which is the same as an HTC universal, they could theoretically use the same Rom but not the same rom as an XDA mini.
Again, this is all in my understanding and keeping it simple.
another idea would be to check the t-mobile site and download your rom directly from them, it should be available. if i find anything for you i'll post back.
Thank you everybody!
After managing to get to the bootloader mode I made a rom update which solved the problem!
Now it works great again!
thanks
Botloader Mode
I have a bricked MDA as I had a power outage while flashing the ROM. Can someone tell me how to recover. I find references to folks entering bootloader mode and then recovering, but I cannot find a post that tells me how to do it. Can anyone help? [email protected]
I'm desperate!
Regards,
Bob
Hi, which MDA is it because the instructions should be included in my post up above. You just need to find which XDA your device corresponds to and go from there. All that info's in this forum somewhere for sure.
Best of luck!
XDA Exec Dead after interrupted Rom Upgrade
XDA Exec Dead after interrupted Rom Upgrade
Hi
I was installing new ROM WM6.1 on autom exec when it rebooted it was showing black screen and just vibrating. as when I hard rebooted it after removing my phone battery and again press the power button it was again showing the black screen and vibrator continues it is not bootng up.
can any one help me please.
How can I reinstall the the old rom using usb
help required....
Please help....
It´s always good to READ the Wiki:
http://wiki.xda-developers.com/index.php?pagename=Uni_ROM_Upgrade
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Keys dont work
Hey i just put WM6.1 on my xda exec and it works fine apart from the keys not working so i have to type using the touch screen and the WI-FI randomly turns off and on i was wondering if anyone else had these problems and if they could help.
Thanks

Upgrading without activesync

After a interruptus ROM upgrade my s200 d'ont start . after the HTC i have a white screen but not more.
The activesync don't connect and i can't put the ROM another time.
I obtain the multicoloured screen with usb in the left botton.
Please, could anybody help me to update the rom in this situation , mayby without activesync ??
Regards.
Edit/Delete Message
i sugest you ask here
http://forum.xda-developers.com/forumdisplay.php?f=293
as more % of the readers of that forum have the same device as
you then this forum
All is OK , Thank's
Yes thank's, i found a ROM that don't need activesync , after that changing that rom by my rom and at the moment my s200 y ok.
Thank's.
tehe same problem
hi
i have a qtek 8310 and have the same problem that u, could u tell me what kind of rom does not need activesync, please?
thanks a lot
Indeed, I have the same problem with my S200, please explain what you did to fix your phone!
For those interrested: I've found the following text in the readme file of the regular ROM updaters (RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID in this case):
8. Q: I use RUU to update and failed, and my device always boots in three-color mode and cannot enter CE OS anymore, what should I do now?
A: If the update process has failed, you will see that your device will always boot in three-color mode. It’s normal and can be recovered. Please follow the instructions below to reset your device and to establish a connection with the computer.
1. Disconnect your PDA Phone from the USB cradle/cable.
2. Reset your PDA Phone.
3. Reconnect your PDA Phone to the USB cradle/cable.
4. Check that the communication cradle/cable is connected properly.
5. Return to the ROM Update Utility.
Note: You should ignore the ActiveSync connection.

XDA Stealth no bootloader (cannot boot)

Dear all,
i've got 2nd hand xda stealth for 2 weeks, now my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram with nb0 extension on miniSD. please any one can help me to recover my Stealth ?
sorry for my bad english.
xda stealth..
go to www.seeo2.com, download a rom upgrade utility from there.. then start upgrade procedure again. As xda stealth is a hybrid phone..dont try any custom roms on it..
thank's malhar for responding my thread.
i already download the upgrade rom from the o2 site (now is www.mwg.com), i put the rom to my SDCard, the problem is how can i enter the boot loader, in case my stealth always in blank screen with call and end button are light.
i already press press power + call + end button, but my stealth stuck on that condition. every method of flashing mode i already try but no response from my stealth.
Syaipul
oh yea malhar, for information i read the procedure for upgrading on o2 site that connect status is required for upgrading procedure in activecync, my stealth has disconnected status when i plug to my com. can i do the upgrade the rom in this case?
buddy, remove ur sd card from the device first..and then hard reset ur device by pressing reset button via stylus, then flag which is windows home key and then ok key..reset+flag+ok.. maintain the sequence..press reset first keep on pressing then flag and ok key.. it will format ur device.... then try to flash new rom on it
ok malhar, i'll try tomorrow. thanks.....1000x
sad-sad-sad
my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram on miniSD. please any one can help me to recover my Stealth
Your SPL boot loader sounds like it is gone, formatted...
You may be able to patch it, using scripts & mtty if you can get into DL mode. Sounds like you're stuck in OEMSBL though.
help me !!!!
i have try pressing flat and ok botton to format . but nothing appear on the screen . is the other way to format or upgrade rom .
• The device doesn't boot, I see only O2 logo. Hard reset doesn't help and the Firmware update process stops with the first message?
1. turn off the device;
2. enter engineering mode;
3. in Main menu choose Boot Config;
4. in Configuration menu choose EBOOT-Launch Image;
5. turn off the device;
6. now hard reset or upgrade firmware.
Sometimes helps another method: leave the device without the battery for about 30 minutes, then turn your O2 XDA Stealth on.
• How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings.
Click to expand...
Click to collapse
follow this thread from YUC wm6
http://forum.xda-developers.com/showthread.php?t=352468
blank screen
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
cant see o2 logo
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
randysng said:
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
Click to expand...
Click to collapse
Have you tried removing the battery for few hours ??? Does the engineering mode work???
engineering mode
engineering mode ? how to set engineering mode ?
randysng said:
engineering mode ? how to set engineering mode ?
Click to expand...
Click to collapse
How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
malhaar said:
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
Click to expand...
Click to collapse
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
khalifa_smart said:
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
Click to expand...
Click to collapse
It worked for me
Goto to your PDA setting and uncheck USB to PC.
Note: Check task before connecting to USB ensure no task including Active Sync.
FYI.
Im using VISTA Ultimate to update my XDA.
From WB 6.1 back to WM5. WM 6.1 too buggy and battery drained fast.
Cheers!
Please help me O2 stealth it dead not boot and blank screen .Are you Jtag for it please post it here.
i have the same problem --- my stealth is absolutely dead after using a cheap local charger
i have dismantled the board and taken some pics of the jtag connectors -- made the common LPT port jtag cable
how to proceed from here ?????
is the procedure similar to that of jtag recovery of a flame or an atom exec ??
how do i find the bootloader for O2 Stealth for flashing the NAND memomy Disk on Chip ??
please share your insights

Not able to Flash a new ROM !? Please help Me

Hey ho guys. I have a question and I hope somebody can help me.
A few Days ago I flashed this ROM:
-----> htc-developers.de/viewtopic.php?f=85&t=2510
(with OliNex Hard SPL and 1.00.25.05 Radio)
Now I wanted to flash another ROM
-----> sites.google.com/site/romshtcplus/
But now I got a Problem. Since I flashed the RTT Xtreme Rom, I am not able to flash another ROM. After the Softreset while flashing, the Mobile Centre of Win7 cant connect to my Diamond anymore.
Hard SPL is possible to flash but Radio and all other ROMS are not flashable -.-
Anyone knows what I can do? I tried the Original O2 Rom but even this one wont work.
I hope somebody knows what do do without killing my phone, cause the Xtreme ROM sux
Thx 4 help
- connect your Diamond to PC in Storage Mode
- rename file .nbh in diamimg.nbh
- copy diamimg.nbh in in your Diamond
- disconnect your Diamond
- press together "Volume Down", "Back" and "Reset" until appears Boot screen called USB Trigger Mode;
- press Power to go next...wait the process until to "Update Complete"
- reset and wait the Automatic installations

[Q] A Problem During Upgrade JasJar

Hii all,
actually this my first post in the forum and i hope to find the solution to my small prob.
The problem is appearance some words on the jasjar screen like "usb" n "serial"
they doesn't disappear although i 'v done "reset" n "Power+reset+backlight"
They are permanently appear on the screen and make my jasjar as dead ..
----
actually i've open the rom upgrade icon from the mobile directly and i didn't use the pc at all because i didn't know how to upgrade it
----
please if someone know the solution of this prob. tell me >>
n i want to know how to upgrade the rom if i already downloaded it >>
Welcome to forums
have a read on my signature link and check for usb connection
Moving to upgrade section
Please orb or anyone can help >> ):
I want the software of the jasjar which come with the installtion cd ..
I tried to join the jasjar with the pc but there's a problem with the usb ..
Plese help me as my mobile now like dead body
Thanks In Advance ;
Hello,
First instal ActiveSync 4.5 in PC. - if not already installed
Code:
http://www.softwarepatch.com/windows/activesync.html
Then in settings in (ActiveSync) disable (NOT check): "allowed to connect to one of the following port" and "Allow connection to USB".
Perhaps the translation is correct. I use the CZ version. But it's second and third check box.
Now
This works for when the Universal is in Bootloader and Windows Mobile.
1. First download the ROM you want to install.
2. Extract it to a folder (use winar or other extraction software).
3. There will be up to 3 ROMs in the package: ms_.nbf (Extended ROM), nk.nbf (OS ROM), radio_.nbf (Radio ROM)
4. Delete those which you don't want to install. (If you just want to upgrade the radio rom for instance delete ms_.nbf and nk.nbf and leave radio_.nbf.)
5. Download UniversalRUU.zip
6. Extract it and copy into that folder the nbf files you want to install.
7. Enter BootLoader mode by pressing and holding the power button and backlight button whilst performing a reset with the stylus. And plug to PC. Wait few seconds.
8. Doubleclick ROMUpgradeUt.exe and follow the instructions
9. When the upgrade is finished pull out the USB cable from the Universal.
10. You will need to do a soft reset OR hard reset depending on the situation. (note: some say do a soft reset / others a hard reset .. possibly someone with more knowledge could correct me here, but until then it's best to investigate the matter for yourself on the forum.)
11. To do a hard reset (push the two menu buttons ("-") on the keyboard + the reset button at the same time (all of this three). Doing a hard reset will result in you losing all your installed apps and data so ensure you have a backup of everything first.) Everything should be fine from this time. You have to calibrate the screen and do some tutorial...
12. If after doing a hard reset you want your Universal not to install the extras from the Extended ROM wait untilsetup is complete and then do a softreset when the popup window appears (you have 3 seconds before it installs ExtendedROM)
For a long time I have not installed the new ROM. I remember so I proceeded as follows
Greetings
Svobi
Really I don't know how to thank u
Thread closed as problem got solved

Categories

Resources