Leadtek GPS 9532 & MDA III - General Accessories

I have the following setup:
MDA III
Leadtek GPS 9532 antenna
MDA/XDAIII specifically moulded Car Holder with RJ 11 connector for GPS & the 'Y' cable feeding from Cigarette lighter to GPS & PDA (Though it's branded XDA I/II)
Tom Tom Navigator 3
However the entire system does not seem to work...
The GPS Antenna comes on flashes red for a while then flashes green roughly once per sec. With both the 'Y' cable and the RJ11 port on the PDA holder the MDA does not seem to want to communicate with the Antenna. I have tried TomTom GPS & WinFast GPS configurator, ceMonitor etc etc...
Not sure if you/anyone has had problems setting it up but if you can please please please help me that would be greatly appreciated.
Com 1 does not seem to exist when I select that one...

Doh!!!
If you have a similar set up and the error Com Port 1 Error appears go to Settings - Connections - Beam: and untick Accept all incoming Beams - it worked for me

Yes Com 1 is the correct port, do as instructed above settings/connections/uncheck beams and also disable any external keyboard driver if installed.

Related

Bluetooth gps with cable

I have used a Fortuna GPSmart bluetooth gps with xda2, I bought an optional cable which powers the xda2 and the gps and also allows data connection to xda or xda2, it needs to be set to Tomtom gps, nmea 38400 and Com 1, beams must be switched off in settings/connections/beams. I also have a Holux GR-230 bluetooth gps, I tried the cable from the Fortuna, with the same settings and it also works perfectly as a wired gps while charging both xda/xda2 and gps. This may be of interest to somebody.
Help
Hi. I have also just purchased the cable and being really stupid l Can't get it to work. Where do I change the settings you mentioned? thanks.
Go to the "gps" section of tomtom, choose nmea 38400 and com 1.
Y-(Data/Power)-cable XDA to GPSmart were to buy in EU
Im looking for a Y-(Data/Power)-cable to connect a XDA2i GPSmart. Where can I buy this in EU?
Also the Holux BT GPS cable shoud be compatible with GPSmart.
But i cant find this in EU.
I got mine off ebay www.ebay.co.uk

XDA2s, Holux GR-230 & Tomtom Nav 3

Hi All,
I am not having any lock setting up XDA IIs, Holux GR-230 GPS and Tomtom 3.07 navigator. If someone has managed to get these 3 talking, then i will be grateful if the settings could be shared with me.
thanks
gosh28us
O2 XDA2s
ROM Ver: 131.00 WWE
Radio Ver: 1.06.00
ExtROM Ver: 1.31.139WWE[/b]
Have you checked which COM port the GR-230 is using and matched it with the tomtom software?
http://www.holux-uk.com/Products/gr-230/download.shtml gives a download for checking out what COM port is used
No, i haven't. I will do that.
thanks
gosh28us
let me know what you find
For what its worth - My Tomtom GPS receiver uses Bluetooth Serial port on COM6: but I know this can be changed to Bluetooth COM5, serial on COM1 and also COM9
XDA2s + Tomtom3 + Holux 230
I have this exact combination working.
Use COM5 BT
Set the type to SIRF 9600 (38400 proved unreliable)
then tick the box on the left.
If you go back to the 1st tab, you should see it's communicating.
Cheers,
Hal
GPS viewer hasn't been able to identifier the port to be used. I have tried the combination given by Hal and that wasn't successful either. I'm now going through all the possible tomtom GPS cobinations and will update you as soon as my luck shines.
Thanks in advance for all your help.
gosh28us
When you pair the gps with your pda do you get the message that a serial port profile is available for the device?? Mine does this and it sets itself up as com 5. I am not sure if beams affects this, I always switch off beams under settings/conncetions/beams, if a wired gps is used this is essential as the beams takes com 1 and wont allow a wired gps to work if enabled.
No. i don't get that message on the XDA2s although I remeber that on the XDA2.
I have downloaded Holux GPS viewer on my PDA but when i scan, it doesn't find any com port
I have deleted the Holux GPS (GR-230) and paired again, went to the Bluetooth screen which shows HOLUX GR-230: SPP slave and it connects and shows the duration clock.
I am and have been changing the options on the TomTom GPS screen, alwyas tick the big box but when i go to the status screen don't see any firing between the attenna and the PDA icons.
thanks
On the XDA, go into bluetooth settings and make sure that under the services tabe, the "Serial Port" is enabled. Unless this is enabled, you won't have COM5 & COM6 on your XDA
Also, once you pair with the device, try exploring it & seeing what services it can provide
Weasel, I have done what you have said below and yes, COM5 & COM6 are among the list when i check the TomTom GPS screen 2nd box.
I have been using different options from the 1st box, ex. TomTom Wireless GPS, TomTom Navigator GPS etc etc, combining with COM5 & COM6 etc etc from the 2nd box but still the status screen doesn't show any communication between the antenna & the PDA.
With regards to the Holux GR-230, should i do anything different apart from turning it on whiles i'm trying to do the setup?
thanks
gosh28us

Problem with XDA IIs and GlobalSat BR305 GPS

Does anyone have this combination of PDA and GPS receiver working together? I got it yesterday, installed the cab file with the driver and then ran the com port test utility and it reported that the GPS was on COM7. Then I go to GPSInfo that was supplied with the kit and it says it can't open Com 7. You can select any port from 1 to 8 and pretty much all of them except 7 say they are open when you select them.
I've also noticed that the LED on the side of the GPS receiver doesn't light up at all, I believe it's supposed to flash or stay on constantly when it's finding a signal. I waited for a few minutes and nothing happend, and GPSInfo failed to report my position.
The GPS receiver was bought with a car mount that has a power cable, I wired it all in and the PDA is charging from the car, the GPS is plugged in correctly as well but it just doesn't want to do anything.
Any ideas?
In case you need it, my device info is :
ROM v.1.31.00 WWE
ROM Date 12/13/04
Radio v.1.06.00
Protocol 1337.38
ExtROM v.1.31.139 WWE

BA not receiving data from Garmin GPS on serial connection

Hello Guru's,
I have a GSM BA with the latest SW upgrades & have not been able to make communication with my Garmin GPS III. I connect the BA & Garmin with 2 serial cables (one is a BA serial cable & the other is a Garmin Serial cable w/ car charger) with a gender changer between these 2 cables. I have tried the following with no luck:
- GPS is set to NMEA standard (4800 speed). It works fine & shows location data on it's screen.
- BA is on COM1 with 4800 speed. I tried all the ports including AUTO configuration.
- I tried Navio & Mapopolis as receiving SW on BA.
- I connected the GPS to computer & could see the data coming on a hyperterminal.
- 'Incoming Beams' is off on BA.
Any help getting me to make the GPS work with BA would be appreciated.
Thanks
A gender changer is not enough, you need a null modem adaptor between the 2 cables otherwise the serial connection is reversed and will not function.
Thanks a lot, I got a Null Modem adapter & it works like a charm

How to set a BT GPS receiver on Universal with WM5???

Hi y'all,
i have a BT GPS receiver that i used with my Qtek 2020 (before this was stolen... ).
Now i have a XDA Exec from O2, but i am not able to set the receiver!
Anyone has any tip for me?
Thanks a lot...
...no one can help me out...??? Please...
Check out this guide and follow from after installing tomtom and you should get BT GPS working with exec, I did!!!
ps search term used was 'tomtom 5.1 guide'
hope this helps!
http://forum.xda-developers.com/viewtopic.php?t=28386
Hello,
first the bad news: not every bt-reciever is working...
but you should try this way:
Connection-Manager
Enable BT
Setting (Connection-Manager) BT-Settings
Tab devices and ad new partnership (be sure, BT-Reciever is on)
Pair it with your Universal (pin is usuall 0000)
Tap Com-Ports: new outgoing Port (your BT-Reciever) set to com 4
Tap Com-Ports: new incomming port (your BT-Reciever) set to com 8
Now it should work!
Thanks for the tipo...now i don't have my GPS receiver with me...but tomorrow i will give it a try.
The only thing that i find strange is: when i try to set the outgoing port i find my BT receiver in a box, but when i try to set the incoming port i dont' find it anywhere.
Something wrong?
Oh...and also...i use the software "GPS View" for the connection with the BT receiver...which port should i open (the COM4, the COM8 or another one?).
I ask you this because i have 10 COM ports available (from 1 to 10), but i cannot open all of them, because some tell me "COM porte error" when i try to open it.
Thanks for your help...
can anyone confirm if haicom-405 bt works with dopod 900?
Hustladave said:
Oh...and also...i use the software "GPS View" for the connection with the BT receiver...which port should i open (the COM4, the COM8 or another one?).
I ask you this because i have 10 COM ports available (from 1 to 10), but i cannot open all of them, because some tell me "COM porte error" when i try to open it.
Thanks for your help...
Click to expand...
Click to collapse
As I wrote before:
Tap Com-Ports: new outgoing Port (your BT-Reciever) set to com 4
Tap Com-Ports: new incomming port (your BT-Reciever) set to com 8
Best wishes
Teja
jona69 said:
can anyone confirm if haicom-405 bt works with dopod 900?
Click to expand...
Click to collapse
I follow the tips ...outgoing port (COM4 - which the only port can be used other failed to open), incoming port (COM8).
But it doesnt work with my Garmin10 .... which work well with my previous XDAIIs. Anyone use Garmin1o with Dopo900?
Thanks
Usually, there's no need to setup an ingoing COM port: my Holux 236 receiver, for instance, works perfectly paired with my Qtek 9000 and only the outgoing COM8 setup'd.
The only thing to pay attention for is that TomTom have to be v5.1 or above (better if v5.21), in order to work properly under Windows Mobile 5.0.
Well...in my previous XDAII worked perfectly using the software MAPSONIC and the GPS VIEWER with my BT receiver (and just setting the outgoing port).
I tried to do like Teja told me in his answer (setting the outgoing COM4 and the incoming COM8), but it still does not work.
I will try to get a TOMTOM 5.1 software to give it a try...
solved...and i don't need to setup the ingoing port...thanks for the tips
Hi there! I have MDA Pro from T-mobile (UK) and until now I couldn't set a COM port appart of COM0 port for BT-GPS...
Now have COM4 for outgoing port and tom tom once is connected after 5 seconds is disconnected and again after 5 seconds is connected and again is disconnected and again......
I am using TT 5.21
Help please
I have set the outgoing port on COM8, no ingoing port needed and it works fine...although i don't have TOMTOM!!!
Orange M5000 and BT GPS and TOMTOM 5.21
I thought I share this just in case there are other like me out there.
I had an Orange M2000 with tomtom 5.0 and 512MB SD card.
I installed TT5 as normal on the PDA but the maps on the 512MB SD card.
I just got an Orange M5000 which is XDA EXEC and could not install TOMTOM 5.0 from CD. The SETUP kept on crashing on XP PC.
Here is the solution:
1) Put the SD card with the maps in M5000
2) Did NOT install TT5 from CD but downloaded navupd521.exe from the tomtom site and installed this on M5000 fine.
NOTE: I did not have to copy CAB files. I just installed this as normal from my PC with the USB cable
3) TT installed fine but I could not get it to recognise the BT GPS
I used the instructions below from the forum:
a) Turn on BT GPS
b) on PDA goto BlueTooth seeting --> New Partnership and supply the password (0000) to pair it.
c) Then in Bluetooth settings select the COM PORTS tab
d) Select Incoming port and set to COM8
e) and again in COM PORTS tab select Outgoing ports and select COM4
f) Start TOMTOM and goto Preferences and find GPS Configuration and select OTHER GPS and select COM4
It works every time... ALL my FAvourites etc are still there so no need to type them again.
So far WM5 and TT5 rocks. I will be testing it on the road with my Plantronics BT headset soon. With my old M2000, usually when TT5 is on the M2000 CPU does not have the juice and Bluetooth devices die or stop responding. Also when I stopped TT5 application the BlueTooth stopped.
We will see how M5000 improves on M2000
Thax...
i believe you shouldnt have a problem running your headset and bluetooth GPS together.
when i had a blue angel i ran TT3 with my SonyErricson Car Kit and the TT3 together and made vioce calls at the same time and even now with the Universal i can do the same! run them both together!
only thing is that occasionaly the TT5 seems to be a little behind my actual location if i have made/received a call luckily by only 30-40 yards so can still use the screen to see where my turnings are.
has anyone else found that and got the cure....
thanks

Categories

Resources